Search Documents

By D. Malhotra

Most primary-molybdenite producers use a selective-flotation process in which molybdenite is floated from the ore while other sulfide and non-sulfide gangue minerals are depressed in the same step (Figure 1). The process was developed at the Climax mill. Reagents used in the rougher-flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother) and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born, et al, (1976) and Malhotra, et al, (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50 percent of the total molybdenite-flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors which would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate non-oil based collectors and collector systems that are less expensive than vapor oil.

Jan 1, 1985

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the con¬ventional petroleum production cycle in then-known fields within the U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oil-or bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67% of the OOIP will remain in place at the end of the

Jan 9, 1980

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays.

Jan 1, 2013

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the conventional petroleum production cycle in then-known fields within th’e U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oilor bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67070of the 00IP will remain in place at the end of the

Jan 1, 1980

By Keith K. Griffiths

Computers are a valuable tool to the aggregate industry and should not be overlooked. The selection of proper mechanical components is necessary. Merely the addition of a computer to operate a mechanical system will not guarantee that the system will work. Material delivery by rail or truck for stock-piling and intra-plant material transfer can be accurately supervised by automation with simplified controls for the layman to use. There are mechanical problems that occur in material blending and load-out systems when such a system is automated. Such things as material flow, bridging, stockpiling methods, overloading of equipment and safety must be considered. How these problems can be overcome by proper selection of compatible mechanical and computer equipment will be discussed. Also, there are many individual material circuits in a plant that can be computerized at a nominal cost. This type of computer installation will not necessarily result in increased production, but it will produce greater efficiency in manpower. These small computers, binary counters, memory circuits and other devices and their application to the aggregate industry will also be presented. A careful evaluation of the mechanical and computer inter-relationship by someone understanding both "Rocks and Electronics" is essential to proper handling of material by computers. Computers for the mining industry may be either digital or analog computers. Unless the computer is to control some type of chemical process, such as a cement plant, the, analog computer is not required and the digital computer' will be quite adequate and less expensive.

Jan 1, 1967

By D. R. Gibbons

This morning I would like to speak to you about an area of chemistry that is enjoying a revival-organometallic compounds. This renewed interest, principally stimulated by defense needs, has already created new markets for the products of the mineral industry. Although the consumption of metals in these new products is modest at oresent, several hold promise of importance. Because this is a new and growing market, I am sure the Council of Economics is aware of many of its facets and is interested in new developments. Of course, the chemical industry has been a significant consumer of minerals for many years. I estimate that in 1957 the chemical-industry purchased a total of $1175 million worth of minerals as raw materials (not including fuels). This estimate can be broken down as follows: [Metals and metallic minerals $375 million Nonmetallic minerals (excluding hydrocarbons ) 330 million Hydrocarbons 470 million $1175 million]

Jan 1, 1958

By Mritunjoy Sengupta

The Green River formations in the Western U.S.A. contains vast amounts of petroleum reserves in oil shale deposits. Exploitation of this petroleum reserve calls for large scale mining of the oil shale. Applicable mining methods include conventional underground mining using roan and pillar, sub-level caving and block caving; underground insitu retorting of oil shale and open pit mining. Roam and pillar mining offers one of the most economic methods of underground mining of oil shale. A 2.4 x l09 litre per year (50,000 barrels per day) of crude oil production would require a daily oil shale production of 100,000 tomes per day from underground operations. For this large production, a highly mechanized room and pillar mining muld utilize large capacity diesel equipment such as 85 tonne trucks and 8m front end loaders. The total air requirements of an oil shale mining operations can. be as high as 28443/s. Ventilation planning for such a large scale underground mining operation presents a formidable task. The major objectives of providing ventilation air to underground workings are to dilute airborne .dust and diesel fumes to harmless levels, and to insure that the mine environment is compatible with the health and safety of mine personnel. Regulation of air velocities and air temperatures is a major factor in mine environmental control. Colorado State law requires that a minimum of 0.047m3/s of fresh air be supplied for each kW of diesel power operating underground. Additionally, 0.047m3/s of fresh air must be supplied for each underground employee, and a minimum air velocity of 0.15m/s must be maintained in all working places. It is desirable to exceed this minimum velocity in order to prevent stratification of ventilation air. Moreover, Colorado law also stipulates the maximum allowable concentration of noxious gases mine air, below: ? C02 - 0.5% by volume, 5,000 ppm. ? CO - 0.005% by volume, 50 ppm. ? Oxides of Nitrogen - 0.0025% by volume, 25ppm. ? Nitrogen Dioxide 0.005% by volume, 5 ppm. This paper examines ventilation requirements for the underground mine, with respect to air quality requirements and distribution of air in mine workings in light of the above regulations. Analyses were made for sane typical mining plans to determine airflow resistance or pressure drops and fan horsepower requirements. In addition, the possible occurrence of high concentrations of toxic gases, was examined. Expected temperature levels in mine workings were approximated.

Jan 1, 1980

By Allan M. Hale

The central Florida phosphate industry is not a recent development. The first phosphate mining occurred in approximately 1888 (1). Many of the original mining companies were "wildcat" operations operated with rapid phosphate extraction as the sole purpose and no long-term commitment to development. Many of the early pioneers were ill-equipped to mine phosphate at either a practical or economical level; as a result many of these early companies "folded" after only a brief period of operation. However, as these early companies went out of business, several large companies developed, expanded their mining territories bought up the folding companies and by 1903 (little more than 10 years after the first mines were started), approximately 37 of the original 60 mines were control- led by three major companies (1). In the early period, mining reclamation was nonexistent. The mined out areas were left to revegetate and reclaim "naturally" over the period of many years. Reclamation practices were only started relatively recently and the various reclamation techniques developed and used in the past have continued to be employed with varying degrees of success through the present time. The reclamation techniques used in the past and currently include land and lakes restoration, sand tailing reclamation, slime ponds reclamation and overburden fill.

Jan 1, 1980

By J. D. Miller, C. L. Lin, J. Dong

Nano clay mineral particles such as kaolinite — with primary particles typically smaller than 2 μm in size — can cause significant problems in flotation processes and tailings disposal, including the processing of Florida phosphate rock and Canadian oil sands. In this study, the consolidated state of flocculated kaolinite sediment was examined, and high-resolution X-ray microtomography (HRXMT) was applied to describe the structure of the consolidated sediment. Using this tomographic information, the complex geometry of the channel network structure for the consolidated flocs was established for the first time. With the establishment of the experimental channel network structure, permeabilities were estimated by flow simulation using the Lattice Boltzmann method. Results for kaolinite sediment with and without polymer are compared and discussed. Results for flocculated kaolinite sediment in a gravitational field are also presented and discussed. The results show that as polymer dosage increases, the permeability of flocculated kaolinite sediment increases, and as suspension pH increases, the permeability of flocculated kaolinite sediment decreases.

By Rollien R. Wells

The Bureau of Mines was created in 1910 by an act of Congress and subsequently directed to: "...conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste ..." Under this broad charter, the Bureau's responsibilities have changed and grown from an almost exclusive concern with coal and coal mine safety to the present emphasis on a full spectrum of mineral producing and consuming problems. In the past 30 years, the domestic consumption of coal, oil, gas, metals, and industrial minerals has more than quadrupled, in parallel with the rapid and enormous growth in industrial production. Of the scores of metals and nonmetals essential to the Nation's progress and security, many are scarce and difficult to wrest from domestic sources. Reserves of some ores are dwindling. Available ore resources are becoming leaner and more difficult to treat. In recognition of this many faceted problem, the Bureau has engaged in a continuing quest for new and improved technology to enable economic exploitation of marginal minerals and fuels, to find substitutes for minerals in short supply, and to create better materials to meet the expanding and diverse requirements of the growing economy. The current central concern of the Bureau is focused on meeting projected fuel, metal, and mineral demands at the lowest real cost by recovery from available resources by new and improved technology that minimizes waste, hazards, and social and environmental problems.

Jan 1, 1970

By E. Haug, Quamrul Ahsan, R. Norcross

Cyanide leaching is the most common process employed in the majority of the gold extraction plants. These gold extraction plants naturally generate tailings and/or effluents that contain highly toxic cyanides, In geographic locations with excess precipitation and therefore net positive water balance, a portion of these tailings must be discharged. Before these highly toxic cyanide-containing effluents can be discharged to the waterways, cyanide and any other toxic substance must be destroyed. Geographic locations with high evaporation and low precipitation, as in the western USA, result in net negative water balance and therefore these plants can operate with a zero discharge option. However, with the current stringent environ­mental regulations and concerns for bird and wildlife mortality, even these operations may be required to partially treat their tailings to preclude potential harm to wildlife. Furthermore, heap leach opera­tions are now generally required to detoxify the heaps before abandonment. It is, there­fore, apparent that all gold extraction plants may be required to install some form of effluent treatment in order to achieve the above objectives,.

Jan 1, 1990

By Patricio A. Espinoza, Aldo Casali, Cristian Ardiles, Guillermo González

Cluster analysis is used to design grade soft-sensors in a rougher flotation plant and a ball mill overload soft-sensor. Soft-sensors are virtual sensors which either replace unavailable actual sensors or infer measurements for non existing sensors. In the case of the grade soft-sensors clustering serves to determine clusters of related operating points. To each cluster there corresponds an ARMAX model structure whose parameters are estimated using only the points in the corresponding cluster. Thus a much better correlation is found than if all the data points were used for a global model. The problem of identifying clusters when the measurement of the real sensor is not available is addressed. In the case of the overload soft-sensor, variables were selected which are related to overload, either from a phenomenological point of view or according to operator experience. Different clusters are formed, some of which are identified as determining an overload condition or a possibility of such condition. Each of these clusters has a set of operating conditions which suggests the corrective action to be taken when necessary. Both kinds of soft-sensors are tested with industrial plant data and promising preliminary results are obtained.

Jan 1, 1995

By C. P. Newman, T. Gray, G. Beale, T. Cluff

Predictive geochemical and limnologic modeling of pit lakes is an important aspect of modern permitting. One of the key assumptions of many predictive pit-lake models is that highwalls and pit backfill become unreactive once submerged by the filling pit lake. Existing pit lakes provide useful data to test this assumption. The Sleeper pit lake (northwestern Nevada) is near hydrologic equilibrium and contains good-quality water that generally meets regulatory requirements for pit lakes. Despite the overall stable geochemical composition, seasonal trends in the hypolimnion indicate the generation of solutes and fluctuations in pH. This work applies mass balance, analysis of subaqueous pyrite oxidation, and trends in solute concentrations to evaluate the potential causes of long-term solute generation in the hypolimnion of the Sleeper pit lake. Results will aid in refining the effect that inundation of highwalls and waste rock has on ultimate pit lake chemistry and long-term closure planning. In the case of the Sleeper pit lake, ongoing solute loading does not substantially change the closure plan at this time as influent groundwater contains abundant alkalinity. INTRODUCTION As mine pit lakes become more widespread, regulatory agencies are increasingly requiring advanced predictive modeling of pit-lake geochemistry during permitting. The end goal of all those involved in these permitting actions (i.e., the mining company, the regulatory agencies, and the public) is to have pit lakes become geochemically and hydrologically stable for the long term, which may then allow mining permits to be relinquished. The modeling endeavors therefore are important to inform long-term closure of pit lakes. The conceptual models and numerical methods used to predict pit-lake water quality are complex and require substantial amounts of data and a variety of assumptions (Castendyk et al., 2015). One of the common modeling assumptions is that solute generation via acid mine drainage is eliminated (or at least decreased) by the filling of the pit lake and inundation of highwalls and any in-pit waste rock. However, few studies have reported on observations that support or refute this assumption. The water-quality record of the Sleeper pit lake is an ideal dataset with which to test these assumptions. The former Sleeper mine is located in northwestern Nevada (Fig. 1), and has been inactive (in terms of ore extraction) since 1996. The mine extracted Au and Ag from the famous high-grade Sleeper vein and associated widespread stockwork mineralization (Nash et al., 1995). Water quality in the pit lake has been monitored since the cessation of dewatering in 1996. The current pit lake actually occupies three separate sub-pits, the Sleeper, Wood, and Office pits (Fig. 1). The Sleeper and Wood pits undergo regular water-column monitoring using a conductivity-temperature-depth (CTD) probe, and sampling for dissolved inorganic constituents at several depths (~10, ~130, and ~330 ft. below lake surface). Groundwater quality is also monitored using a series of wells (Fig. 1).

Jan 1, 2019

Roof bolting has been widely used in hard rock underground mines for its many advantages. In this paper, the applicability of roof bolts to mine openings in frozen ground and effects of bolts on the stability of the openings are presented. A comprehensive finite element program ABAQUS, was used to analyze the temperature distribution, the stress field, and the displacement field around a mine opening. Openings supported by roof bolts and unsupported were analyzed. The thermal and mechanical processes were treated as a quasi-coupled problem, with the thermal analyses being conducted first, followed by the mechanical analyses in each case. For the opening under consideration with a roof area of 15 m2, five to seven roof bolts are appropriate. When the number of bolts are less than five, the displacement within the ground can be improved only locally.

Jan 1, 1995

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By Ian M. Loomis, Keith G. Wallace

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy research and development facility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste. The waste storage horizon is 655 m (2150 ft) below surface in bedded salt. To date the WIPP project has not emplaced any waste. There are three intake shafts used to supply air to the underground. All air is exhausted though a single return shaft. The total design airflow during normal operations is 200 m3/s (424,000 cfm). The ventilation system is designed to provide separate air splits to construction, experimental, and storage activities. Separation is achieved by isolating the storage circuit from the construction or experimental circuits with bulkheads. Any air leakage must be towards the storage area of the facility. Field studies have shown that the pressure differential necessary to maintain the correct leakage direction is susceptible to the effects of natural ventilation; therefore, extensive studies and analyses have been conducted to quantity the natural ventilation effects on the WIPP underground airflow system. A component of this work is a monitoring system designed to measure the air properties necessary for calculation of the natural ventilation pressure (NVP). This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure at strategic locations on surface and underground. The psychrometric parameters of the air are measured every fifteen minutes. From these data, trends can be determined showing the impact of NVP on the ventilation system during diurnal variations in surface climate. Both summer and winter conditions have been studied. To the author's knowledge this is the first reported instance of automatic and continuous production of time and temperature variant NVPs. This paper describes the results of the initial monitoring study. INTRODUCTION The ventilation system at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, is designed to perform two distinct functions. First, it supports normal mine ventilation requirements complying with all state and federal mine regulations. Second, the system is designed to prevent an uncontrolled release of radioactive contaminants from the storage and transportation areas of the facility. Although a nuclear radiation release in the facility is considered unlikely, many special features are implemented in the ventilation system to prevent the possible spread of contamination. The facility is constructed with the waste transportation and storage areas separated from the mining and non-radioactive experimental areas. The ventilation system is designed such that air leakage is from the mining and experimental areas to the storage areas. Furthermore, radiation detectors are located throughout the storage and waste transportation areas underground and an exhaust filtration building is installed on surface to prevent the possible release of radiation to the environment. For over two years the underground ventilation system has been rigorously tested and balanced. It was during this period that the adverse effects of NVP were noticed and subsequently quantified. From extensive field studies and computer models, several mitigating features were designed and constructed and special operational procedures were implemented to control the impacts of NVP. To quantify more accurately the NVP at the WIPP, a continuous monitoring system was installed. This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure every fifteen minutes at strategic locations on surface and underground. From this psychrometric data, the NVP is calculated. Fan operating pressures and flows and strategic differential pressures are recorded from the site Continuous Monitoring System (CMS). The monitoring system provides a means of evaluating how the ventilation system behaves in regard to climatic conditions and to judge the efficacy of the mitigating features and operational procedures. To the author's knowledge, continuous calculation of NVP as a function of time and surface temperature has not been previously reported. Overview of the Waste Isolation Pilot Plant The U.S. Department of Energy determined that the plastic nature of bedded salt may provide the best solution to isolate transuranic (TRU) waste from the biosphere. Initial evaluations at the WIPP site began in 1974. In 1979, the United States Congress enacted Public Law 96-164 for the construction and development of the WIPP project. The mission of the WIPP is to demonstrate the safe, long-term disposal of TRU waste generated by the national defense programs of the United States. TRU waste is classified as a low to medium level waste. The waste is stored in drums and does not produce significant heat (not greater than 1 W per drum). The WIPP site is located approximately 47 km (29 miles) east of Carlsbad, New Mexico in the Chihuahuan Desert. The repository is located in the 630 m (2000 ft) thick Salado Formation. This Permian Basin salt deposit is about 225 million years old and appears to have been minimally disturbed by earthquake, faulting, and ground water activity since it was deposited. The underground facility is 660 m

Jan 1, 1993

By David M. Spatz

Team, as defined by Katzenbach and Smith (1993), is a small number of people with complementary skills who are committed to a common purpose, performance goals and approach for which they hold themselves mutually accountable. As the mining industry searches for new ore discoveries increasingly under post-mineral cover, the process of mineral exploration has taken us from prospector to geologist to multidisciplined explorer to multi-disciplinary team. Multidisciplinary exploration techniques have improved in terms of sensitivities and penetration and more than ever before each technique requires specialists with appropriate training and skills to process data and interpret results. To produce a quality product, specialists must collaborate openly and honestly in an atmosphere where the collective result takes into account the knowledge and expertise of each individual and the relationships between all pertinent data sets.

Jan 1, 1998

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979

By R. M. Von Storch

Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that influence miring. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined, conditions are met in most coal mines in southeastern Utah including those of the United States Steel Corporation. This coal bed measures up to 16 feet in thickness, the pitch is as much as 25% and mining is under a cover approaching 2, 000 feet. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colorado. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest..It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development.

Jan 1, 1967

By C. L. Karr, D. E. Goldberg

This paper considers optimization of the design and operation of an air-injected hydrocyclone (AIHC) via a genetic algorithm (CAI. The AIHC is a mineral separating device, developed by the U.S. Bureau of Mines, that combines the selectivity of flotation with the capacity and simplicity of hydrocyclones. GA's are search procedures based on the mechanics of natural genetics. Computer results demonstrate the ability of a GA to rapidly locate design and operating parameters that improve AIHC performance. A computer model of the GA-designed AIHC predicts improved recovery over that currently being obtained with an AIHC in operation at the U.S. Bureau of Mines Tuscaloosa Research Center.

Jan 1, 1990