Search Documents

By E. J. Rorem

Rockfall and unstable rock slopes can be effectively controlled by utilizing steel wire rope net systems, either as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting, permitting kinetic energy dissipation, yet providing high strength and consequently low maintenance. A review of the design considerations involved with these systems, as well as a review of several mine and non-mine installations is presented with the hope that the information may contribute to the safety against the dangers of rockfall and other mine hazards in active and abandoned mines.

Jan 1, 1996

By Werner A. Ruemmele

Eisenhower Memorial Tunnel, called Straight Creek Tunnel during construction is located 60 miles west of Denver, Colorado at 11, 160 ft. elevation. It is 8, 510 feet long, and carries two lanes of 1-70 traffic under the Continental Divide. This paper describes improvements and changes made in construction methods for utilities, concrete lining, ceiling, wall covering and paving to allow maximum offsite fabrication and activity overlap resulting in a one-year faster completion for traffic. The substantial changes proposed on a design-and-construct basis by the contractor and put into effect after State approval were: 1. Substitution of ductile iron and thick-wall P.V. C. pipes for clay pipes allowing placement and operation before hole-thru. 2. Outside pre-assembly of large rebar mats, using a novel tension-splice with cable clamps. 3. Arch concrete placement method modified to make 4, 322 ft. of lining in 10 weeks possible. 4. Safety barriers precast and epoxy coated offsite instead of cast-in-place and tile faced. 5. Prestressed hollow ceiling slabs with porcelainenamel coated steel sheets assembled offsite, instead of in-place glazed tile and in-place cast concrete ceiling. 6. Glazed tile wall panels 8 ft. long by 11 ft. high assembled off site and erected using vacuum pad mounted on special lift. 7. Asphalt paving while other work proceeded, instead of reinforced concrete slab and asphalt overlay. Work started in January 1968, but advance came to a one-year standstill for major structural redesign and negotiations of a new agreement during 1970. Using multiple drift construction followed by top-heading and bench excavation, it then progressed to hole-thru in July 1972. As a result of art 18-month overlap of activities the tunnel was opened for traffic only eight months later in March 1973. Gibbons and Reed Company of Salt Lake City, Utah sponsored the joint Venture of Al Johnson-Gibbons and Reed-Western Paving-Kemper during 1971, 1972, and 1973. The tunnel was the subject of a previous paper delivered at the RETC '72 in Chicago by R. C. Hopper, T. A. Lang, and A. A. Mathews, describing geology, unusually severe structural loading and multiple-drift tunnel excavation.

Jan 1, 1974

By C. L. Pillar

In the capitalistic system the success of a mining enterprise is measured by the rate of return on the investment and the speed by which its redemption is achieved. Exploration in search of ore deposits often results in the emergence of the lean orebody which does not meet basic company requisites. At this point a decision must be made whether to place the orebody into production or postpone production pending more favourable market conditions. The wisdom of this decision, borne out by future results, demonstrates the quality of a company's management and is instrumental in the degree of financial success it achieves. The project feasibility report must show a rate of return on the capital invested that is attractive to the company, plus its full redemption in the desired period of time, in order to bring the property into production on a sound economic basis. Mining companies have demonstrated their ability to bring the profitability of a marginal property from a point that says "no go" to a point of "go" by substantial reduction of expenditure without adversely affecting production rate or cost. Here is where the real challenge exists for today's mining engineers and plant designers; they will have to develop better ideas and concepts: ideas that will still allow maximum production at reduced capital expenditure, This is the sound way marginal orebodies can be brought into production without inflationary increases in the price of their product.

Jan 1, 1969

By William A. Vogely, Robert T. Deacon, Walter J. Mead

Oil and gas together are the most important energy sources consumed in the United States. In 1983, 67% of total energy consumption was represented by these two resources (43% was oil and 25% natural gas), while coal accounted for only 23% of U.S. energy use. All other sources (hydroelectric, nuclear, geothermal, wood and other waste products) accounted for only 10% (U.S. Department of Energy, 1983, p. 1). In this chapter we address the issue of regulation in the oil and natural gas sectors of the U.S. energy industry. In addition, we analyze the cartel characteristics of the Organization of Petroleum Exporting Countries (OPEC). If OPEC is an effective cartel, then U.S. oil as well as substitute energy prices, production, and consumption will be affected by cartel action. Further, as the nation learned in the 1970s, major changes in oil prices produced major disturbances in other sectors of the U.S. and world economies. Consequently, it is important to determine whether the roughly ten-fold increase in nominal prices that occurred in the 1970s was the result of cartel action, the result of normal economic forces adjusting to the fact that the world was running out of cheap oil, or some combination of the two. Furthermore, the presence of OPEC- associated oil price increases is related to regulations that were imposed on the energy sector during the decade of the 70s. THE RATIONALE FOR GOVERNMENT INTERVENTION Economists have traditionally judged the state of an economy to be efficient if it is impossible to improve the welfare of any one member of society without harming someone else. Any economy that satisfies this condition is said to be Pareto efficient, after the Italian economist Vilfredo Pareto who first gave rigorous attention to such questions (see Chapter 4.10). It is easy to see why an economy that fails to satisfy this condition could not be efficient; by definition, it would be possible to alter the allocation of resources in a way that improves everyone's welfare.' Much of the appeal of this weak efficiency criterion is that it avoids comparisons of levels of well being among different individuals. The cost of such generality, however, is that in any given economic system a wide array of different Pareto efficient states will typically be attainable. In the simple Robinson Cursoe economy of the undergraduate textbook, for example, efficiency could just as easily be attained in the case where most of the island's resources are owned by Friday as in the case where they are under Crusoe's control. However, the distribution of welfare among the two inhabitants would obviously be quite different in the two situations. Such equity issues cannot be settled on objective or scientific grounds. To decide which distribution of welfare is socially "best" an explicit value judgment is needed. It is useful to keep in mind the preceding distinction between efficiency and equity issues when analyzing the role of government in a market economy. Decentralized market processes will not necessarily result in a distribution of welfare that society considers just. For this reason a potential role for government lies in the redistribution of income among individuals. In some circumstances, however, market pro-

Jan 1, 1985

By J. Partyka

Respirable dust produced during blasting operations in underground mines exhibits both diffusion and convection properties of the airflow. However, the application of the mathematical model presently used to calculate the change in time in the concentration of blasting pollutants is mostly limited to a single drift and cannot be easily utilized for blasts taking place in stopes. This paper discusses an analytical solution based on considerations that enable us to reliably identify the initial condition. Such an approach may be used for any blasting area regardless of its position, its size, or the ventilation system in use during blasting. In addition, a test procedure using field data is established to determined those parameters not measured directly. As well, equations are derived to find the diffusion coefficient, and the position and size of a dust source from the field data. Mathematical considerations The convection-diffusion problem, for a one-dimensional case, is described by the following partial differential equation (PDE): ct. = Dcxx - Vcx + source - sink(1) where C = the concentration of a pollutant T = time V = the mean air velocity in x-direction D = the diffusion coefficient X = distance away from the pollutant source source = any additional pollutant source specified by an initial value problem sink = decay of a pollutant inside the region specified by the boundary conditions. Respirable dust produced during blasting is best considered as an initial value problem (IVP). To derive a mathematical model, the following assumptions are made: •At time zero (t = 0), the dust source is at point x = 0 of an infinite drift. •The problem is considered a one-dimensional case. •The mean velocity of air and the diffusion coefficient are constant. •There is no source or sink of dust other than specified at point x = 0 and time t = 0. We have to solve the following problem [PDE ct=Dcxx-Vcx-m<x...m;0<t<m(2)] ICc(x,0)=f(x)t=0, the initial condition Where c = dust concentration in mg/m3 V= the average mean velocity in a drift in m/s t= time in s D= the diffusion coefficient in m2 /S x = distance coordinate in m. We observe that in problem (2), we have moved the boundaries to[ -m and +m] in order to have an initial-value problem. We introduce new coordinates, s = t and z =x - Vt. To rewrite the PDE in terms of (z, s), we use the chain rule ct = czzt + csst = -Vcz + cs cx = czzx = cz cxx = (cz)x = czz. We now substitute our computed ct, cx. and cxx into the PDE to get new IVP in terms of z and s :

Jan 1, 1991

By A. S. Paschoa, A. W. Nóbrega

INTRODUCTION There are now over twenty years since the radiological characteristics of the brazilian regions of Araxá, Tapira and Barreiros, three locations adjacent to each other, in the state of Minas Gerais, Brazil, started being surveyed by investigators from the Instituto de Biofísica da Universidade Federal do Rio de Janeiro (IB/UFRJ), Pontifícia Universidade Católica do Rio de Janeiro (PUC/RJ), and New York University (NYU) (Roser and Cullen, 1958; Cullen et al, 1980). The importance of the Araxá apatite – Ca5,(P04)3(OH, F, Cl) - and pyrochlore - NaCaNB206F - for the production of large quantities of fertilizers and niobium was early recognized (Roser and Cullen, 1958). Interesting data have been gathered and published throughout the years on the contents of naturally occurring radionuclides in geologic materials, soils, grass, foods and waters of the Araxá region (Eisenbud, et al., 1964; Penna Franca, et al., 1965a, b; Roser et al., 1966; Penna Franca et al., 1970; Cullen, 1977; Penna Franca, 1977; Cullen and Paschoa, 1978; and Cullen et al., 1980). The radioactivity of the Araxá region is associated with mineral deposits of niobium rich pyrochlore and phosphate rich apatite. There are in this region mineral ores with 3 to 5% pyrochlore with 2 to 2.5% Th as Th02 and 50 to 150 ppm U308 in the matrix, while the apatite deposits contain up to 150 ppm U308 and a thorium concentration similar to that of the pyrochlore deposits (Paschoa and Palacios, 1981). As an indication of the high thorium content of the Araxá soils the 228Ra and 224Ra activity concentrations were reported to range from 10.6±0.2 to 62.4±0.7 pCi228Ra/g soil in 7 samples and 2.1±0.1 to 104±1 pCi224Ra/g soil in 19 samples (Cullen, et al., 1966). The uptake of radium isotopes by edible roots vegatables and fruits growing in the soils of the Araxá region can be illustrated by the data listed in Table I. The biological availability of natural radium isotopes in some segments of the Araxá soil allows a large variation in the 228Ra, 224Ra and 226Ra concentrations in vegetables and edible roots, as can be seen in Table I. This fact makes quite difficult a quantitative local assessment of the radiological implications of mining the Araxá mineral deposits of pyrochlore and apatite for production of niobium and phosphate fertilizers, respectively; since one cannot easily separate the naturally occurring from the technogically enhanced radionuclide contents of foods. The position of the city of Araxá inside the contour of the state of Minas Gerais appears in the upper part of Figure 1, which shows the outlined map of Brazil with the positions of the cities Brasilia and Rio de Janeiro also indicated. The lower part of Figure 1 is a representation of the Araxá region in an expanded scale, which indicates the locations of the pyrochlore and apatite deposits in relation to the city of Araxá, as well as the nearby hydrographic basins. The distance between the city of Araxá and the pyrochlore deposit is about 8 km, and between the pyrochlore and apatite deposits is 4 km. This paper deals tentatively with the radiological implications of the industrial operations taking place in the Araxá region for the exploration of the pyrochlore and apatite deposits. However, one must bear in mind, firstly, that the radiological implications of these industrial activities are by far too complex to be covered adequately by the limited amount of data to be presented in this paper, and secondly, that such implications cannot be considered of local character only. INDUSTRIAL OPERATIONS The commercial exploration of the Araxá deposits of pyrochlore and apatite started only few years ago, motivated by the increasing demand of niobium and phosphate fertilizers in Brazil and the world. As a consequence of the industrial operations in Araxá, a redistribution of the uranium, thorium, and radium originally present in the local deposits of pyrochlore and apatite started occurring in the seventies, with possible radiological implications for the Araxá region and its immediate surroundings, not to mention the destinations of the end products of such industrial operations. A literature review on the radioactivity associated with the extration industries of selected minerals was made by the USEPA (Bliss, 1978). The low level radioactive wastes of the industries for copper ore mining and rare metals processing have been object of particular attention (Fitzgerald, Jr., 1976; Eng, et al., 1979), but the short and long term implications of the radioactivity associated with the niobium industry were also subjects of concern (Knight and Makepeace, 1978). Recently, high 232Th and 226Ra concentrations in samples from the tin mining industry in West Malaysia were reported (Hu et al., 1981). A great deal of attention has been dedicated to the implications of the redistribution of radionuclides originally present in the mineral ores used by the phosphate fertilizer industry (Moore, 1967; Menzel, 1968; Spalding and Sackett, 1972; Eisenbud, 1973; Guimond and Windham, 1975; Guimond, 1976; Roessler,

Jan 1, 1981

By B. C. Scott

Every year more and more mining companies are entering joint ventures to look for minerals. Large companies join large companies, small companies join small companies, and large companies join small companies. Mining companies join oil companies, chemical companies, machinery companies, and companies with no other connection to the minerals business. And well they might, for here is a way for both minerals-oriented companies and those that have no background or knowledge of the minerals business to get actively involved in an outwardly-attractive but high-risk enterprise with the chance to participate in a lucrative minerals find. Thus, for reasons beyond those normally associated with joint ventures in many other fields, corporations, companies, groups, and even individuals are looking to joint exploration ventures as the answer to all problems of getting into or staying in mining.

Jan 1, 1972

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs&apos; work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By D. M. Steelman

Digital systems have been employed in industry as an aid in process evaluation and control for about 20 years. The earlier systems were quite simple and did little more than periodically scan a multitude of process variables, perhaps comparing them to alarm limits, and print out the results. As time passed, the needs of industry and the imagination of process engineers became more demanding. Rather than perform only alarm checking and logging, operating guides were generated to help the operator gain optimum performance from the process. Eventually, systems were entrusted with the job of manipulating the set points of the local analog control loops in a (DDAC) digitally directed analog control mode. Today digital systems are used to gather all-the process information, including both analog and digital variables; to make the necessary data manipulations; and to control the process end elements in a (DDC) direct digital control mode. During these years of transition from the very simplest systems to the complex systems of today, the demands upon the system engineer have been every increasing. The process engineer has required, among other things, more computational ability at high speeds, faster input and output rates, greater flexibility, better communication facilities (man-machine interface), (process oriented software), and finally, greater reliability at lower cost.

Jan 1, 1969

By A. K. Bhowmick

Size reduction is very energy intensive and is the single most power-intensive operation in mineral processing plants. Research has shown that only a small part of the energy is utilized efficiently. One of the major thrusts of all equipment manufacturers has been to improve this efficiency. Choosing the right equipment to maximize energy utilization in any comminution application has always been the utmost criteria. Due to the high energy cost and depletion of good grade minerals, it is becoming essential to optimize all the subsystems within a given comminution system for the overall economic success of such ventures. Bradley Pulverizer Company of Allentown, Pennsylvania recognized this and started offering its Feeder Controller in 1988 for automatic feed control. After its first successful operation, Bradley made this as a part of all of their grinding system standard offering. It was also recognized that the Feeder Controller was just a beginning and more automation and controls would be required for an overall, efficient grinding system.

Jan 1, 1993

By H. J. Brown

Pluess-Staufer (California) Inc. Lucerne Valley California operation is one of the largest producers of high brightness high purity fme grind limestone products in western North America. The San Bernardino Mountains area of southern California contains the largest high brightness, high purity limestone mining operations and undeveloped reserves in western North America (Fig. 1, Brown 1987). Combined annual production of high brightness limestone products from several operations is approximately 1.5 million tons, with an estimated gross value of $75 million dollars per year (Fig. 2). An additional 5.0 million tons of cement grade limestone is mined by several large cement producers in the nearby Mojave area (Brown, in press). The purpose of this paper is to summarize the geologic setting, genesis and mining of white, high purity crystalline limestone by Pluess-Staufer (California) Inc.

Jan 1, 1994

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways, has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit, and a number of surveying technicians, has proven, in the past, to be a very expensive and time-consuming operation. Alignment with a laser has solved most of the problem. Figure 1. With the advent of the Perkin-Elmer Model 5620 Construction Laser, use of laser light is now both dependable and economically feasible for unlimited applications in modern construction and surveying. The laser projects a continuous, narrow red beam of brilliant light, providing a constant alignment reference, and will not interfere with operations.

Jan 1, 1968

The National Mining Hall of Fame and Museum (NMHFM) in Leadville, CO will induct the class of 2011 on Sept. 10, 2011. Representing the coal, metallurgical/processing, research and development, marble and lead industries, this year?s inductees cover a diverse crosssection of the mining industry. William Francis Diamond, Wayne Hazen, Redfield Proctor and Jeffrey Zelms will join 210 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 24th Annual Induction Banquet and Ceremony. The members of this year?s class were selected for being visionaries, leaders and ambassadors both within their own sectors and across the industry at large. Diamond had an illustrious engineering and managerial career that spanned four decades with Island Creek Coal Co. During that time, he was responsible for the engineering and construction of the deepest coal mines producing in North America at the time.

Jan 1, 2011

By Harrison A. Schmitt

During .the past five decades or so we have passed from a time when it was difficult to point to a mine or an ore body and verify that it had been discovered by geological methods, through the. Twenties when the common saying was, "Who ever heard of a mine found by a geologist?", to recent decades when hundreds of mines and ore bodies are acknowledged geological discoveries and the above query can be ignored. Recently, however, the application of mining geology appears to have been downgraded, or so it seems to me. Basic geology in mining has been cheapened and glossed over in favor of geophysics and outcrop sampling, even though the latter is merely one technique of mining geology and, to some extent anyhow, has been used for a. long time. (Locke, 3, pp 81-87). Geophysics by itself and in conjunction with geology has had success in certain geological provinces, but limited attainment in mountainous terrane except in those few cases where strongly magnetic minerals are associated with ore. Nevertheless, in the Cordillera .many experimental techniques are offered as proved ones. This is not an intent to try to depreciate honest geo- physics. Continued experimentation and use of it is approved by all, but at the same time it is foolhardy to throw mining geology overboard, Generally both approaches should be considered and usually, at first anyhow, geology is the most direct one.

Jan 1, 1960

By William H. Langer

U.S. Geological Survey (USGS) recently initiated the Front Range Infrastructure Resources Project. This is a multidisciplinary study along the Rocky Mountain Front Range from Pueblo, Colorado, to Cheyenne, Wyoming, and is designed to collect, compile, and analyze new and existing data on natural aggregate (stone, sand, and gravel), as well as water, and energy resources. To identify aggregate resources in the Front Range, a 1:500,000-scale reconnaissance map showing locations and quality of both bedrock and surficial sources of natural aggregate in the Front Range urban corridor was prepared by processing the digital geologic maps of Colorado and Wyoming. The first step of the process was to identify map units as either bedrock or unconsolidated material. Bedrock was classified according to type (i.e., limestone, granite, gneiss, etc.), which in turn was classified based on the suitability of the bedrock for use as crushed stone. Unconsolidated materials were classified according to relative age, with the older, more weathered materials being defined as less suitable for use as aggregate than younger materials. As a spin-off from the Front Range Project, the techniques developed for analyzing the Front Range geology have been modified and expanded to include all of Colorado and New Mexico. More detailed digital aggregate maps (1:24,000 scale) are being prepared in collaboration with the Colorado Geological Survey (CGS). Maps from the CGS "Atlas of Sand, Gravel and Quarry Aggregate Resources, Colorado Front Range Counties" show the distribution of potential resources of sand and gravel and provide general information about the physical properties of the resources. These maps are being digitized and merged into a single Geographic Information System (GIS) data base. In addition, the project is adding more specific information to the maps about deposit thickness, volume, and quality. This additional information is being obtained through field-characterization studies and modeling activities. The GIs data base can be displayed and queried using off-the-shelf software such as ArcInfo?, ArcView?, and Map Professional?. In addition, the USGS is developing a decision-support system to assist users in analyzing various land-use options on resource availability.

Jan 1, 1999

By K. Baba

Liberation of valuable minerals from a gangue matrix during size reduction of multiphase mineral particles is an important objective in mineral separation processes. A methodology for the prediction of volumetric grade distribution from one dimensional, linear intercept image analysis is being developed using a transformation function to describe the relations hi p between the linear and volumetric grade distributions. As part of this research effort it has been found that a transformation function, derived from Monte Carlo simulations of irregularly shaped particles, mainly depends on the volumetric grade and the dispersion density, i.e., the number of nuclei (or grains) per particle. A possible mathematical form for the transformation function is described in detail.

Jan 1, 1985

By Zong-Xian Zhang, Charlie C. Li

It has been observed that the rock debris of a strain burst event are often in the mode of tensile fracture. Seismic waves could create tensile fractures in the material nearby reflecting surfaces, such as at the boundary of the fracture zone and the rock surface of an underground space. The fractured rock could be ejected to the space when the seismic waves are powerful enough. The average ejection velocity of the ejected rock is a measure of the magnitude of a burst event. The ejection velocity is directly associated with the released energy from the seismic waves and with the strain energy stored in the rock prior to the burst. In some cases, the seismic wave induced tensile fracture and the energy conversion occur in successive moments during bursting. In this paper, tensile fracture caused by seismic waves is investigated through an 1D model. The relationship of the average ejection velocity of the ejected rock in a rockburst event is analytically established with the energy of the seismic waves and the strain energy stored in the rock.

Apr 26, 2022

By Y. S. Roditis

Traditionally, open pit optimization has been used to produce a single outline which can guide the pit design. This paper describes how a series of optimum nested pits are utilized to: a. produce different mining sequences and to help in mine planning and phase design; b. evaluate different metallurgical processes, production scenarios and equipment size; c. investigate the sensitivity of a project to prices, recoveries, production rates, costs, ultimate pit slopes etc.

Jan 1, 1993

By Rodrigo Estay Huidobro, Andrés Martinoli, Claudia Pavez-Orrego

The effects of induced seismicity caused by mining activities are one of the main problems that the mining industry faces. Although it has been documented by countries with a great mining tradition (United States, Canada, Australia and Chile) for over a century, the problem has been intensified throughout the years due to the greater depths that mineral extraction reaches, where the stress levels and environmental conditions increase the possibility of a rockburst occurrence. Seismic events inside the mine cause important losses of human lives and infrastructure damage. To deal with this problem it is necessary to implement several kinds of safety protocols. For example, seismic indicators allow to identify, through the analysis of a set of seismic parameters -magnitude, energy, time, decay rate, among others-, periods of time when a seismic event of considerable magnitude is most likely to occur. The objective of this work is to use the frictional energy generated by a microearthquake inside the mine as a seismic indicator, linking it with the occurrence of large magnitude seismic events which are outer the background activity. Thus, we seek to determine the set of seismic parameters which allow the best performance of the frictional energy/heat indicator. In the present study, we considered magnitude, frictional energy, and time as seismic parameters to study the efficiency of the proposed indicator. The optimal set of parameters was determined using two different methodologies: accumulated thermal energy and alert bands. The Piece Skill Score and the Accuracy indexes were used to evaluate each set of parameters. Both approaches show a high rate of true positive and true negative hits. Furthermore, it was concluded that both methods show complementary results in terms of the detection of critical events (Mw > 3.0).

Apr 26, 2022

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"There are three distinct producing iron ranges in Minnesota, the Vermilion, Mesabi and Cuyuna. In trend the Vermilion and Mesabi are approximately parallel (E.N.E. and W.S.W.) and about fifteen to twenty miles apart. The Vermilion lies farthest north, near the. Canadian boundary. It is from seventy-five to eighty miles due north of Duluth. The length of its productive part is about twenty miles.The Mesabi Range is from fifty to seventy-five miles north and northwest of Duluth. Its length along the strike is about 110 miles, and the length of its present productive area about eighty miles. The Cuyuna range lies southwest of Duluth nearly ninety miles, and is the last of the Lake Superior iron ranges to be developed. The relative positions of the ranges are shown on an accompanying map. The Mesabi Range is by far the largest producer and contains the largest ore reserves of the three. The Cuyuna is next in quantity of proven ore, and in production since 1916, while the Vermilion is first in average quality of ore.On the west, both Vermilion and Mesabi ranges disappear beneath heavy glacial drift; and on the east, extend into Canada, the so-called Gunflint range near the international boundary being an eastward continuation of the Mesabi formation. This latter range is of no economic importance, however, at present. The exploration and development of the Cuyuna range has proved up a considerable tonnage of manganiferous iron ore, besides ordinary merchantable iron ore."

Jan 1, 1920