Search Documents

By William Kohan

The industrial grinding process has undergone changes to better address the market and economic needs. Fine grinding of dry materials has developed to the point where classifying linings and fine ball charges improve mill efficiencies. Roller mills as well have wide acceptance due to their power efficiencies. The mill, by its nature, cannot provide the specific particle size or range of sizes which are required for further processing or final use. Therefore, various separators are operated in conjunction with the mill to control particle size. The sizing device helps minimize over grinding and control top size. Rising energy costs combined with increasingly tighter quality specifications have led to increasing study of the grinding and separation process.

Jan 1, 1985

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By Jr. Bacon

Kaolin clay is one of the yeoman minerals. It sees duty in almost every aspect of our lives: -in and on most paper products (from modern newsprint to National Geographic and packaging board) sometimes as much as 25% (by weight) of the product -40% of the tile (ceramic, rubber, and linoleum) you walk on. -15 % of the tires you ride on, -30% of the fiberglass filaments in circuit boards, bathtubs, boats, doors, and more, -25% of many housepaints, adhesives, grouts, caulks, and putty -30% of sparkplugs, power insulators, dinnerware. and toilets, -50% of most catalysts (both cracking and emission control) -20% of cosmetic powders. -20% of wire insulation, and animal feed to rocket insulation!

Jan 1, 1993

By Hasan Sevim

This paper summarizes recent developments in modeling of underground coal slurry haulage networks for determination of optimum design and operating parameters. The model presented here is based on a stochastic dynamic programming formulation, applicable in any typical room-and-pillar and/or longwall mining configuration commonly practiced in the United States. The formulation and the structure of the model is general enough to handle design problems involving more than one face and mining method. Given the stochastic operating characteristics and a system layout, the model can be used to determine the equipment configuration and operating regimes that minimize the overall unit cost of coal haulage.

Jan 1, 1983

By Peter Kowalczyk

The acquisition of submarine gravity data using airborne gravity technology is a practical reality. Ocean Floor Geophysics plans to deploy a free-swimming ROV based submarine gravimeter on a commercial basis in early 2009. The submarine instrument is a variant of the well-used GT-1A airborne gravimeter. Airborne gravity surveys are now routine. The primary factor controlling the accuracy of airborne gravimeters is the precision of the GPS measurement of vertical movement of the sensor platform. The gravity measurements along a flight line are the differences between the output of the gravimeter vertical accelerometer and the estimate of the aircraft vertical acceleration using the differential GPS system. The principle difficulty of moving an airborne gravimeter to a free-swimming submarine platform is the necessity to have an accurate real time estimate of the changing elevation and hence changing vertical acceleration of the platform; GPS doesn't work underwater and an accurate estimate of depth fluctuations to the necessary precision is difficult to acquire. It is interesting that the airborne gravity gradiometer technology, which competes with the airborne gravity technology, was first developed as a classified military application for use by missile submarines during the cold war. Gradiometers were developed for this application specifically to avoid this problem. A gradiometer does not require as accurate an estimate of its vertical position to make a useful reading- it measures gravity gradients, not the gravity field itself.

Jan 1, 2008

By W. E. Lytle

Environmental permitting is a critical component for joint-venture projects located in the Commonwealth of Independent States (CIS). This paper presents the basic CIS regulatory environmental requirements for permitting of a hypothetical mining source and emphasizes air permitting. Topics which will be covered include: the Expertiza process, air pollution quantification, data requirements, and air pollution modeling protocol. A comparison will be made between permitting requirements for air pollution sources in the United States and a CIS country, Kazakstan.

Jan 1, 1998

By John Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulfide concentrate that must be treated by roasting, biooxidation or pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process that also meets Ontario's stringent environmental regulations. A comparison of biooxidation and pressure oxidation was completed early in 1990. Placer Dome selected pressure oxidation as the preferred process to replace the roaster. The commercial plant design was based on technology supplied by Sherritt Gordon. In July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The Campbell Red Lake Mine, in Balmertown in northwestern Ontario, is the first plant in Canada to use Sherritt Gordon's pressure oxidation technology to recover gold from a refractory ore body. A similar process has been used at Sao Bento in Brazil since 1986. The Porgera complex in Papua New Guinea also uses Sherritt's technology. At the Campbell Mine, gold occurs as either free gold or is encapsulated with sulfide minerals, mainly arsenopyrite, pyrite and pyrrhotite. These sulfide species are recovered from the ore by crushing and grinding to 80% -75. µm (200 mesh), followed by flotation. About 40% of the gold in the ore is recovered by gravity separation. The remainder reports to the ground slurry feed to flotation. The flotation concentrate averages about 55 to 60 t/d (60 to 66 stpd). A typical analysis is shown in Table 1. Before the installation of the pressure oxidation plant, the flotation concentrate was treated in a two-stage, fluid bed roasting circuit. Roaster off-gases passed through two parallel sets of cyclones, followed by electrostatic precipitators. Arsenic trioxide was captured in a four-chamber baghouse before the gas was discharged to a stack. The arsenic trioxide was sold or conveyed to an underground storage vault. The roasted calcine was fed to a gravity separation circuit and then subjected to cyanide leaching. Gold was recovered from the filtered leach solution in a Merrill-Crowe zinc precipitation circuit.

Jan 1, 1992

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By Thomas E. Howard

Engineers today face a tremendous challenge. Growing population and rising standards of living all over the world are creating unprecedented and accelerating demands on and for all kinds of technology. At the same time, the public is becoming more and more conscious of--and concerned with--the impact of technology on human welfare. The growing controversy over the Supersonic Transport is a case in point, It is clear that the modern engineer must expect to spend a growing share of his time considering this dilemma and evaluating the tools that are available to him, not only with respect to their adequacy for the job at hand but also their capability for meeting the increasingly demanding--and, in many cases, conflicting--requirements of the future. This meeting seems a particularly appropriate place to speculate about the future of mining technology. The summary of the state-of-the-art in surface mining contained in the papers scheduled for the International Conference, together with the recently published Surface Mining volume, constitute not only a major contribution to the technical literature but also form an impressive record of technologic progress. That record, and the advanced technology displayed in the exhibits, and to be discussed in the SME technical sessions demonstrate engineering achievement in which the mining community can justly take pride.

Jan 1, 1968

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992

By J. L. Vanderbeek

The SAG milling of ores with markedly variable grinding rates presents definite process control challenges. Decisions must be made regarding the selection of the most appropriate combination of mill volumetric load level, percent solids, and mill speed for the combination of ore types being processed at the moment. An investigation was performed concerning the effects of these parameters. General results are presented.

Jan 1, 1985

Strainburst phenomena, generally characterized by a sudden release of energy in a volume of highly stressed rock, are often encountered in such situations like crown pillar bursts in cut-and-fill mining, face bursts at development headings and floor bursts in deep shaft sinking. This paper describes a simple FE modeling approach which leads to the calculation of the energy release rate (ERR) and the total energy storage rate (TESR) in the rock mass around the openings. The merits of using such energy parameters in the analysis of strainburst problems to identify areas of high energy release/storage are discussed. However, much site-specific back analyses are needed to better understand how strainbursts and energy parameters are inter-related.

Jan 1, 1998

By R. J. Sweigard

Estimated costs and revenues can be used in the evaluation of post- mining land use alternatives. However, post-mining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There- fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact upon each alternative under consideration. In this paper, a method is presented which employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1986

By L. M. Yokum

Tremendous strides have been made in front end loaders in the last fifteen years. Fifteen years ago a 2; cubic yard front end loader was the largest standard machine you could purchase. Today there are two commercially available 15 yard front end loaders and many 10 yard front end loaders. The estimated total worldwide market for all front end loaders over one cubic yard has increased to over 30,000 units yearly. The trend for front end loaders, in general, and for the mining market, in particular, is to larger and larger loaders. Today there are 18 cubic yard and a 24 cubic yard front end loader in prototype form. It is not inconceivable that within another fifteen years that there will be front end loaders in the 50 cubic yard class with design features quite different from today's. These larger loaders are being designed at the demand of the mining industry and the design criteria are being directed at this market area. The costs of these larger loaders will be greater per unit of capacity, and it is the intent of the various manufacturers that they will be more reliable, be easier to service, give greater availability, live longer, and cost less to maintain, than previous loaders. It is also the intent of the manufacturers to compete directly with the large mining shovel as the front end loaders become appropriately larger and more reliable. There has been some trend in this direction in the past with smaller shovels and loaders. In Figure No. 1 are data for U.S. production of front end loaders (5-6 cubic yard class and 10 cubic yard class) and U.S. production of cable operation, crawler mounted power shovels, draglines and cranes (1; to 5 cubic yard class) for the years 1965 and 1970. (Source: Bureau of Census, U.S. Department of Commerce.)

Jan 1, 1972

By Kapila Pathirage, Michael S. Schultz, Gregory Sanders, Ulf G. Gwildis

Adequate understanding of the subsurface conditions along the alignment of a planned tunnel is key for managing project risk. For achieving this understanding, geotechnical borings are conducted during design. Where their spacing cannot reduce the risk of encountering differing site conditions (DSC) in-between borings to an acceptable level, supplemental exploration methodologies or data evaluation approaches may be required to bridge the data gap. This paper compares the exploration design approaches of recent tunnel boring machine (TBM) and microtunnel boring machine (MTBM) projects in the quaternary deposits along the Eastern Seaboard, the glacial geology of the Pacific Northwest, the sedimentary rocks of the South, and metamorphic rocks in western Germany, describing their respective effectiveness of managing DSC risk.

Dec 1, 2022

Sphalerite is commonly floated in an alkaline environment and under such conditions the overall activation mechanism is obscured by the hydrolysis of Cu2+ and precipitation of Cu(OH)2. Electrokinetic and kinetic flotation tests show that the activation of sphalerite is a two-stage process; the activation products formed on the surface of sphalerite in near neutral and in alkaline solutions in the first rapid activation stage are "flotation-inactive". These layers, when formed in an alkaline solution, are unstable and are transformed into the "flotation-active" form in the second stage. However, the surface layers formed during activation in alkaline environment by copper in the presence of lead ions are very stable and even after a long conditioning time the flotation rate is not improved. Consequently, while both Cu2+ and Pb2+ activate sphalerite flotation, quite unpredictable effects may result when both are present in the solution.

Jan 1, 1997

By O. Guyot, A. Broussaud, J. Björkman, P. Söderman, P. O. Samskog

Model-Based Expert Control systems (MBEC) are on-line supervisory dynamic optimization systems which combine the ability of a phenomenological model to generate a large amount of information about the state of the process and predict its evolution, with the flexibility of a rules-based approach to take plant constraints into account and apply a complex control strategy. For its new concentrator started in 1995 in Kiruna (Sweden), LKAB has implemented a progressive grinding flowsheet with closed-circuit autogenous grinding followed by closed-circuit pebble grinding with ore pebbles. The standard for instrumentation in this new plant is very high. The control hardware consists of a Distributed Control System (DCS) through which the operators interact with the plant, supplemented by a site-level Management Information System (MIS). A state-of-the-art MBEC system was imbedded in the MIS by the authors before plant start-up. It consists of several modeling and expertise software modules: a phenomenological process model and a Kalman filter estimate continuously the state of the process, an optimizer calculates an optimum feedrate, while rules-based modules establish production targets and key process set-points. The decision to install the MBEC system as an integral part of the new plant before start-up illustrates the current maturity of the technology, i.e., enough know-how was accumulated through former projects to design and develop the system to a large extent without accessing the plant. The feasibility and the power of dynamic optimization systems were previously demonstrated in Kiruna pre-existing concentrator by the authors. First, a MBEC system was installed on the three existing pebble mill circuits, providing both an increase in quality (stabilised size distribution) and a 10% increase in capacity. An on-line expert control system with limited modeling capabilities was also installed in the existing flotation plant, with the aim of stabilizing phosphorous content in the concentrate and optimizing collector additions. Both objectives have been achieved.

Jan 1, 1995

By T. K. Kim

Iron, cobalt, and nickel in waste ferric chloride solutions were separated from each other by solvent extraction. The iron was extracted from the cobalt and nickel by the use of methyl isobutyl ketone, and then the cobalt was separated from the nickel by the use of a high-molecular-weight quaternary amine dissolved in a solvent of high aromatic content.

Jan 1, 1980

By Frank R. Cappuccitti

This paper will deal with current market trends for sulfide mineral collectors in three distinct parts; the global market for sulfide collectors, collectors as tools to solve mineral processing problems and new collector Research in the 1990's. The global market and manufacturing of sulfide collectors will be detailed as well as the trend towards using increasing amounts of specialty products. The use of Total Quality Concepts for laboratory and plant evaluations of new products will also be discussed. Research in the 1990's for sulfide collectors will need to focus not on the development of new chemical species but on the application of the new technologies that have already been developed.

Jan 1, 1994

By George M. McArthur

General Statement In Montana, as in most states, the requirements for water quality control are becoming more restrictive. What was once accepted practice is now obsolete. The planning and construction of water quality control facilities has taken on new importance. Past practices and new ideas must be examined to meet the challenge. By this paper we hope to encourage the exchange of ideas for the improvement of water quality control techniques. Both the mining industry and governmental agencies should benefit from such an exchange. The following is a summary of the work done and in progress by The Anaconda Company in Butte to provide an improved water quality related to production processes. We invite your comments. Acknowledgements This paper would not have been possible without the efforts of many individuals and departments in The Anaconda Company, including the Environmental Engineering Department, Mr. Frank J. Laird, Director; Montana Operations, Mr. M. K. Hannifan, General Manager, and their assistants.

Jan 1, 1972