Search Documents

By Paulo Roberto Pereira

This paper is motivated by the belief that increasing drilling and blasting costs will not necessarily bring about better digging or crushing productivity. As a matter of fact it can be counter productive as the ensuing discussion will show. In the two case studies presented herein when powder factor increased, productivity at a rope shovel and at a primary crusher decreased. Experience has shown that equipment (shovel and primary crusher) productivity increases as the powder factor increases and concurrently operating costs decrease. This is illustrated by Figure 1where the graph shows (assuming drilling costs constant) that for increases in powder factor initially operating costs might fall till a certain point and then they start to go up again. By the same token we need to understand what is the behavior of the operation’s productivity. It seems intuitive productivity goes up for increases in powder factor but when an operation reaches the point of minimum operating cost one could say that productivity reached its maximum. For continuing increases in powder factor can productivity still go up or does it go down? This paper presents two examples where the productivities of a surface coal mine and of a quarry are reduced for increases in powder factor. This indicates that these two operations could be operating to the right of their minimum operating costs and maximum productivity and therefore wasting precious drilling and blasting dollars and resources. Moreover, their productivity is following the red dotted line in Figure 1 and the question becomes can they follow the blue dotted line for increased drilling and blasting costs? The industry owes to itself to determine this minimum operating cost point and what can be done in case that the productivity goes down afterwards despite an increase in drilling and blasting costs. In other words, utilize your drilling and blasting resources correctly. In the two examples that follow single explosive loading strategies make powder factor a valid means of comparing the results of productivity as a function of powder factor. Also, external factors such as equipment operator influence are eliminated due to the long time span considered in the analysis

Jan 1, 2005

By Armin C. Supp

Since 1975, about a dozen high capacity flotation plants have been installed in the Ruhr district. Depending on the size of the preparation plants, the design capacity of the flotation section is between 100 - 150 t/h. The flotation units generally comprise rougher and cleaner stages in which 5 to 6 or 4 to 5 agitators respectively are arranged in line. The unit volume allocated to each agitator is up to 16 m3. The type of flotation machines, the design of these plants and their instrumen¬tation and control equipment are described in detail. The run of mine coal in the Ruhr district is characterized by a wide variety of the volatile matter. Generally, a distinction must be made between coals with more than 30 - 35% V.M., which are preferably used in power station, and coal with lower V.M. content, which are preferably used as coke-oven feed. The difference between these coals in respect to grain-size distribution, ash cotent and flotation properties will also be described in detail.

Jan 1, 1985

By T. J. Harvey, W. van der Merwe, J. Joubert

GeoBiotics, LLC and Kumba Resources (Pty) Ltd are jointly developing the GEOCOAT® heap bioleaching technology and downstream processing technology for recovery of zinc from tailings at the Rosh Pinah Mine in Namibia. This paper outlines the development of a computer simulation for the bioleaching of sphalerite and the downstream processing. Computer modeling has shortened the product development cycle by allowing many flowsheet scenarios to be analyzed negating much of the expensive and time consuming laboratory testing. A model was developed using the Limn® system which is an Excel® Add-In flowsheet drawing and solution engine. Given that most engineers are familiar with Excel® this software is extremely easy to use and has less hidden calculations making model verification much easier.

Jan 1, 2003

By Vladimir Nikolić, Alex Doll

The Bond ball mill grindability test is one of the most common metrics used in the mining industry for ore hardness measurements. The test is an important part of the Bond work index methodology for designing and measuring the efficiency of mineral grinding circuits. In spite of being called “Bond’s Law,” the work index equations are not a law of nature; but rather an empirically measured regression of a large data set collected by the Allis- Chalmers corporation in the period between 1930 and 1952. As a regression, it is valid within a specific “calibration space,” and great care is required when deviating the test procedures or observing results that are outside of that calibration space. This paper is a collected summary of other works by the Authors that describe feed sizes, product sizes, quality control checks, and other information about interpreting the test and using its results. Examples of adjustments that are sometimes required when using the test are: changing the test product (P80), and coping with a feed that is too fine to apply the “proper” feed preparation steps (such as is sometimes observed from HPGR or SAGDesign product testing). Related metrics, like the Morrell Mib value and Levin B value will be discussed, along with recommendations for their use on design projects. The intended audience is any user of laboratory work index test data.

Feb 1, 2024

By S. Frimpong, G. Galecki

Dump truck tires are often used in long-haul roads in rugged terrain, with high rolling and grade resistances. These conditions increase the ton-kilometer-per-hour (tkm/hr) or short-ton-mile-per-hour (stmph)rating of tires, leading to tread wear, cuts and complete failures. The load-bearing capacities of these tires are sometimes exceeded, with truck overloading, overstressing, heating and subsequent failures. In addition, truck tire demand far exceeds the current supply capacity, with long lead ordering time. This condition has caused severe tire shortage, and the problem is expected to be sustained in the long-term. Industry has taken extensive practical measures to prolong tire service life with significant results. However, this problem can be solved through fundamental and applied research initiatives. This paper pioneers a research effort in tire service life using multibody physics, fatigue failure modes and soil failure dynamics to develop tire-road contact force dynamics. A virtual prototype simulator of the tire-road contact, using the CAT 775E (with standard tire 24.00R35) was developed and simulated within the MSC.ADAMS/NASTRAN environments. The results show the areas of the loaded tires with maximum Von Mises, principal and shear stresses, which could result in fatigue failure, tire wear and tear and blowouts. The maximum Von Mises stresses on the six truck tires are between 35 and 58 MPa. The maximum shear stresses are also between 19 and 33 MPa. These stresses will cause early tire failures given an average operating schedule of between 20 and 24 hours per day. The isolated areas with maximum stresses will be subjected to further studies to reduce stress intensity while preserving tire performance.

Jan 1, 2012

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/AgCl reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrode to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 1994

By Jeffrey B. Smith

Introduction The gas shortage is going to be with us for some time to come. If we can set aside political and industry rhetoric (along with subjective personal opinions), we still are confronted by two serious "facts of life": (1) for almost a decade the U.S. has been consuming natural gas at a greater rate than we have been finding new reserves; and (2) there is a finite amount of natural gas present within the earth&apos;s crust. Much of the known and easily exploitable sources of gas (the so-called "conventional" sources, such as the high permeability sand reservoirs of the Tertiary sequence along the Gulf Coast) already have been developed; their production is declining rapidly. The total producible reserves from conventional gas reservoirs amount to only 216 Tcf, less than an 11-year supply. However, several large potential resources of natural gas remain to be developed. These "unconventional sources" have low permeability and/or peculiar producing characteristics. The DOE program for development of these unconventional sources of gas is called the enhanced gas recovery (EGR) program. The primary goal of this program is to provide a data base of resource characterization and production technology that will lead to commercial development. DOE will encourage and support industry participation in developing and demonstrating technologies needed to reach this goal. Unconventional Resources Four major unconventional resources of gas have a high potential for commercial development. There are other unconventional sources (such as gas hydrates) that are too poorly defined to warrant a major development thrust at this time. The four unconventional sources of gas currently included in the EGR program are: 1. The carbonaceous shales of Devonian age in the Appalachian, Illinois, and Michigan sedimentary basins are the targets of the Eastern Gas Shales Project (EGSP). 2. The low permeability, low porosity so-called "tight" gas sandstones of the Upper Cretaceous/Lower Tertiary in the Rocky Mountain areas constitute the resource target for the Western Gas Sands Project (WGSP). 3. The free methane trapped in coal beds of both the eastern and western U. S. constitute the Methane from Coal Beds Project (MCBP). 4. The abnormally high pressured, high-temperature saltwater aquifers of the Texas-Louisiana gulf coast are targets of the Geopressured Aquifer Project (GPAP). Basic implementation strategy for these EGR projects involve (1) assessing and characterizing the resource potential of the resource; (2) conducting cost-shared field testing with industry to improve, develop, and demonstrate various stimulation and production technologies; (3) coordinating EGR activities within DOE and with other federal agencies (such as the Bureau of Mines) to minimize duplication; and (4) aiming all projects toward commercial development of the gas resources. EGSP What type of "geological animal" is the EGSP dealing with? While gas undeniably is related to the occurrence of natural fracture systems within the shale, the overall producing mechanism and precise location of fractured, gas-bearing locales within each basin is still poorly understood. By developing reliable resource characterization techniques and applying effective stimulation technologies we intend to elevate the Devonian shale from the status of a potential gas resource to that of a proven gas reserve. Once we have done this the private sector can take over the large-scale commercial development of the Devonian shale gas resource. WGSP The second largest project (both in terms of complexity and level of funding) is the WGSP. The primary targets for this project are the low permeability (< 1 md) gas sandstones of the Piceance, Uintah, and Greater Green River basins and the Northern Great Plains Province. Project success in these four primary geologic locales will permit investigating additional low permeability sandstones in 16 other sedimentary basins. It appears that the only practical means of increasing permeability and resultant flow rates from these sandstones lies in the use of massive hydraulic fracturing techniques. Unfortunately, it is still too early to design such jobs with predictable results. MCBP The MCBP is to be involved in producing and utilizing methane derived from coal beds. The coal, like portions of the Devonian shale, is impermeable, highly fractured (termed "cleat" by

Jan 9, 1980

By Niels Jonassen

INTRODUCTION The occurrence of the radioactive element radium, [2gg~a], often in trace amounts, in the crust of the earth gives rise to a flux of the daughter product radon, [&apos;ii~n], across the earth-air interface. This so-called exhalation process has been studied by many investigators [KO 45, Kra 64, Pe 66, Wi 741] over several decades. In the earlier investigations the exhalation process was studied in a purely geophysical context, but over the last 20 years it has been realized, that under certain conditions the exhalation may be intense enough to also have radiological implications. This is for example the case where relatively radium-rich wastes or by-products, like uranium mill tailings and phospho-gypsum, are stored in larger quantities. In order to be able to predict the radiological impact on the environnent it is necessary to know the rate of exhalation of radon from the surface of the exhaling material. Usually the determination of these exhalation rates has been done by measurements in situ directly upon the accumulated material [~le 74, Ha 791. Although such field measurements have the obvious merit of dealing directly with the full scale problem, the results are often lacking in generality, making predictions for other situations difficult or even impossible. The present paper describes some results of an investigation where it is attempted from laboratory measurements on samples of limited size to obtain material parameters, which are suited for extrapolating and predicting the radiational behaviour of larger accumulations of the material. THEORY Let us consider a sample of a radon exhaling material enclosed in a container with a dead space volume, Vd, and initially containing radon free air. If the total exhalation rate (number of atoms per unit time) is c, the radon concentration (number of atoms per unit volume) N will initially grow with the time t according to the equation [ ] where [R] is the decay constant of radon. As the concentration (or activity) in the container grows, the net exhalation rate will slow down because of back diffusion, and, furthermore, radon atoms may be removed from the container, not only by radioactive decay, but also by diffusion leakage [JO 81 ]. If, however,only the initial. part of the activity growth curve is considered, the total exhalation rate, c, is given by [c = r•Vd(2) where r is the initial activity growth rate in the container. Let the container be cylindrical with an inner cross-section S and filled to a height L with a radon exhaling material with the specific mass p, the porosity E, the radon pore production rate f and the diffusion length i. When the container is left open,i.e. the radon exhalation takes place into a virtually radon free room, the radon area exhalation rate, E, can be written [Jo 80] E = Ef?t tanh L.R (3) assuming the exhalation only takes place in one direction, towards the surface of the material. It appears that for values of L > 2•ithe area exhalation rate becomes E a = Efi (4) independently of the sample dimensions and the total exhalation rate c is then c = E •S (5) For L ;~ 0.5•i, tanh P _ k and equation (3) may be written E ~ EfL (6) then c = EfL•S = p•m= Em •m (7) where m is the mass of the sample and Em = P (8) is the mass exhalation rate. It thus appears that the radon exhalation rate from a given amount of material may often be conveniently expressed by c = E •Sfor L z 2•I (5) a orc = Em •mfor L0.5•i (7) where S is the total exhaling area and m the total exhaling mass, E and E the area and mass exhalation rates respectively defined by equations (4) and (8).]

Jan 1, 1981

By Omar A. Muhtadi

8.1 INTRODUCTION Several methods currently exist by which gold may be recovered from a pregnant leach liquor. Two of these methods are discussed in this chapter, the Merrill-Crowe (zinc cementation) process and the carbon adsorption process. These two methods represent the most frequently used techniques for gold extraction and are, -in fact, used almost exclusively in U.S. heap leaching operations. Because of the efficiency and ease of use of these two methods, it is extremely likely they will continue to be quite prevalent within the gold mining industry in years to come. The remainder of this chapter includes information on the history of the two processes, descriptions of the actual processes, criteria to consider in selecting a recovery process, and commercial design and construction considerations for both of the gold recovery methods. As with other chapters in this book, some fairly technical information is presented for the benefit of those readers needing a greater level of detail. However, the overall intent of the chapter is to provide an overview of the processes likely to be used in gold extraction, thus giving the reader a firm basis for more technical research into the topic, should this be needed. 8.1.1 History of Zinc Cementation During the late 18901s, zinc cementation was introduced for the precipitation of gold and silver from cyanide solutions. This occurred at about the same time as the introduction of the cyanidation process, the history of which is recapped in Chapter 1. The initial cementation process involved introduction of a gold-bearing cyanide solution onto a bed of zinc shavings. It proved to be quite inefficient because the reaction rate was very slow. The zinc quickly became "passive", inhibiting further gold deposition. Shortly after this first introduction, zinc precipitation was improved by adding a lead salt (usually lead nitrate) to the zinc. This allowed a zinc-lead couple to form on the surface of the shavings, eliminating passivation of zinc surfaces and thereby allowing continued deposition of gold. Further improvements were shortly forthcoming. The first of these involved the use of zinc dust rather than zinc shavings. This provided a much

Jan 1, 1988

By Jeffrey B. Smith

Introduction The gas shortage is going to be with us for some time to come. If we can set aside political and industry rhetoric (along with subjective personal opinions), we still are confronted by two serious "facts of life": (1) for almost a decade the U.S. has been con¬suming natural gas at a greater rate than we have been finding new reserves; and (2) there is a finite amount of natural gas present within the earth&apos;s crust. Much of the known and easily exploitable sources of gas (the so-called "conventional" sources, such as the high permeability sand reservoirs of the Tertiary sequence along the Gulf Coast) already have been developed; their production is declining rapidly. The total producible reserves from con¬ventional gas reservoirs amount to only 216 Tcf, less than an 11-year supply. However, several large potential resources of natural gas remain to be developed. These "uncon¬ventional sources" have low permeability and/or peculiar producing characteristics. The DOE program for development of these unconventional sources of gas is called the enhanced gas recovery (EGR) program. The primary goal of this program is to provide a data base of resource characterization and production technology that will lead to commercial development. DOE will encourage and support in¬dustry participation in developing and demonstrating technologies needed to reach this goal. Unconventional Resources Four major unconventional resources of gas have a high potential for commercial development. There are other unconventional sources (such as gas hydrates) that are too poorly defined to warrant a major development thrust at this time. The four unconventional sources of gas currently included in the EGR program are: 1. The carbonaceous shales of Devonian age in the Appalachian, Illinois, and Michigan sedimentary basins are the targets of the Eastern Gas Shales Project (EGSP). 2. The low permeability, low porosity so-called "tight" gas sandstones of the Upper Cretaceous/Lower Tertiary in the Rocky Mountain areas constitute the resource target for the Western Gas Sands Project (WGSP). 3. The free methane trapped in coal beds of both the eastern and western U. S. constitute the Methane from Coal Beds Project (MCBP). 4. The abnormally high pressured, high-temperature saltwater aquifers of the Texas¬Louisiana gulf coast are targets of the Geopressured Aquifer Project (GPAP). Basic implementation strategy for these EGR projects involve (1) assessing and characterizing the resource potential of the resource; (2) conducting cost-shared field testing with industry to improve, develop, and demonstrate various stimulation and production technologies; (3) coordinating EGR activities within DOE and with other federal agencies (such as the Bureau of Mines) to minimize duplication; and (4) aiming all projects toward commercial development of the gas resources. EGSP What type of "geological animal" is the EGSP dealing with? While gas undeniably is related to the occurrence of natural fracture systems within the shale, the overall producing mechanism and precise location of fractured, gas¬bearing locales within each basin is still poorly understood. By developing reliable resource characterization techniques and applying effective stimulation technologies we intend to elevate the Devonian shale from the status of a potential gas resource to that of a proven gas reserve. Once we have done this the private sector can take over the large-scale commercial development of the Devonian shale gas resource. WGSP The second largest project (both in terms of complexity and level of funding) is the WGSP. The primary targets for this project are the low permeability (< 1 md) gas sandstones of the Piceance, Uintah, and Greater Green River basins and the Northern Great Plains Province. Project success in these four primary geologic locales will permit investigating additional low permeability sandstones in 16 other sedimentary basins. It ap¬pears that the only practical means of increasing permeability and resultant flow rates from these sandstones lies in the use of massive hydraulic fracturing techniques. Unfortunately, it is still too early to design such jobs with predictable results. MCBP The MCBP is to be involved in producing and utilizing methane derived from coal beds. The coal, like portions of the Devonian shale, is impermeable, highly fractured (termed "cleat" by

Jan 1, 1980

By Francis Martino

There are numerous techniques and predictive models used by geologists and mining engineers to define coal reserves and plan mines. The traditional reserve estimation methods commonly used include the isopach, triangular, polygonal, inverse-distance weighting, weighted-moving-average, and trend-surface methods. Geostatistically-based estimation techniques are now being examined by many geologists and mine planners as a superior alternative to these traditional methods. With today&apos;s coal mine development costs often exceeding $100 million, and power generation $1 billion, it is logical that a technique that can indicate the degree of confidence associated with a reserve estimate (fuel supply), and thus also the degree of risk, is highly desirable to the coal producer, the financiers, and those desiring to commit to coal utilization under short or long-term supply arrangements.

Jan 1, 1983

By T. Bartnitzki, N. Fietz

"INTRODUCTION For a long time now automation has been state of the art in production engineering and chemical engineering. The advantages of automation are, for instance, higher reliabilities of production processes, higher product qualities as well as capacities and improved safety conditions for the personnel. In contrast, many operations in mining are still conducted manually by machine operators instead of autonomous control units. One example for this is the excavation of underground hard coal which is still executed with aid of human perception. The Institute for Mining and Metallurgical Machinery (IMR) has been working on possibilities for sensor-based automation of mining machinery for many years now. Thereto the focus is set on the implementation of common material analysis techniques into ruggedized conditions as a basis for automation. Laser-induced breakdown spectroscopy (LIBS) for instance is an atom emission technique which enables the determination of the elemental composition of a sample. After introducing LIBS this paper will give an overview on dust formation during the cutting process. With the illustration of a few examples the challenges in determining dust concentrations specifically such of cutting processes are explained in further detail. The final chapter will outlay the possibilities and challenges in utilizing cutting-induced dust for the automation of shearer loaders. LASER-INDUCED BREAKDOWN SPECTROSCOPY LIBS Fundamentals LIBS (laser-induced breakdown spectroscopy) is a contact-free method for analyzing materials in any state of aggregate. It pertains the atom emission techniques and is based on the generation of plasma, inducing avalanche ionization on the surface of a solid material or any spot in a gas or aqueous solution. With sufficient background information on the expected elements and an additional calibration, this method can determine all present elements not only qualitatively but also quantitatively. However, this method cannot be utilized for determining the molecular composition of materials – if this feature is required a complementary method such as Raman analysis needs to be added. (1, 2)"

Jan 1, 2015

By G. Van Weert

Oxygen transfer from dispersed air in agitated slurries represents an important unit operation in the minerals processing industry. Gold leaching, iron precipitation and especially bio-oxidation come readily to mind. However, little engineering information is available on the variations between impeller types on such O2 transfer. Engineering literature on the subject, i.e. information which relates slurry density and energy input to O2 transfer, is reviewed and compared to current experimental work. The latter was carried out with minus 50 micron sand/water slurries in a 64 I laboratory tank of standard proportions, equipped with a variable speed drive with torque meter. A standard Rushton turbine and a specifically sized A315 were compared. Results confirm an increasing impairment of O2 transfer with increasing slurry density for both impellers. The volumetric mass transfer coefficient, k,a, in a 10 vol. % slurry shows a decrease of 30% compared to the k,a in water. At 20 vol. % sand this decrease is near 50 %, depending somewhat on superficial gas velocities. Power efficiency, i.e. the kg O2/kWh, decreases about 25 % more rapidly for the Rushton turbine than for the A315 with the addition of sand. However, for equivalent O2 transfer the Rushton turbine was more efficient in this work. Experimental results are presented and their significance for slurry bio-oxidation discussed.

Jan 1, 1996

By S. Klein, M. McLeod, K. Johnson

The East Bay Municipal Utility District (EBMUD) delivers water to the San Francisco Bay Area through an aqueduct system extending from the Sierra Nevada Mountains to the East Bay. This aqueduct system, the Mokelumne Aqueducts, are comprised of three 82-mile long steel pipelines. The portion of the aqueducts crossing the Sacramento-San Joaquin River Delta is recognized to be vulnerable to seismic and flooding hazards. Previous studies evaluated alternatives for mitigating these hazards and increasing the reliability of the aqueducts for the next 100 years. The preferred solution involves construction of a 16.5-mile tunnel across the Delta and re-routing the existing aqueducts through this tunnel

Dec 1, 2022

By David K. Ingram

The objective of this U.S. Bureau of Mines investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored during the mining of two adjacent, 900 ft wide longwall panels in southeastern Ohio. The panels were separated by a five entry, four pillar system (about 350 ft wide). The overburden thickness in the study area ranged from 214 to 280 ft, and the extraction thickness averaged 70 in. To delineate the geology of the overburden, six coreholes were drilled along a profile line extending across the two longwall panels. Multi-point borehole extensometers (MPBX) with eight-anchors were installed in six boreholes to measure subsurface displacements. The MPBX units were continuously monitored using a data logger. During the mining of the first panel, displacement occurred in a radiating pattern beginning just above the extracted area in the center of the panel and extending upward and outward towards the surface and margins of the panel. Overburden deformation did not project over the gate road entries. During the mining of the second panel, the MPBX&apos;s showed almost simultaneous displacement, indicating that the overburden began to move as a whole unit. Again, overburden deformation was confined to the immediate panel area. At both panels, overburden movement began when the longwall face was approximately 55 ft beyond the line of MPBX boreholes. Moreover, all ground movement was complete when the longwall face was approximately 200 ft beyond the line of MPBX boreholes. This paper discusses the results of the study and identifies the characteristics of overburden deformation.

Jan 1, 1986

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35 percent), ceramics and glass (32 percent), lubricating greases (9 percent), air treatment (5 percent), continuous casting mould flux powders (5 percent), polymer production (4 percent), primary aluminum production (1 percent) and other uses (9 percent) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014).In the 1990s, the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced during this period were consumed in the glass, ceramics and aluminum industries. In the 1980s and 1990s, there were two major lithium operations in the United States: brine operations at Silver Peak, NV and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, NC. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period, it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994).Lithium is still produced from the brine operations at Silver Peak. But in more recent years, Chile has become the world’s leading producer of lithium carbonate from brines. Australia has maintained its position as the world’s largest producer of lithium mineral concentrate, the majority of which is exported to China to produce lithium carbonate and lithium hydroxide (Jaskula, 2014).A spodumene concentrate was also produced at the Tanco Mine in Manitoba, Canada beginning in the 1980s through to 2010 when lithium operations were suspended due to fluctuations in the lithium market price (Martins et al., 2013)."

Jan 7, 2017

By K. A. Natarajan, K. S. N. Murthy

Growth of Thiobacillus ferrooxidans on pyrite mineral surfaces and in 9K leach media was studied through estimation of bacterial protein in the different phases. Bacterial attachment was found to be governed by particle size of the mineral, period of incubation and by stationary or agitation conditions used during incubation. Increased bacterial growth in the liquid as well as on the solid phase was observed with decreasing particle size and increasing incubation periods. Increased bacterial attachment to pyrite mineral surfaces was observed to promote iron dissolution.

Jan 1, 1993

By Ron Drake

The Anderson Dam Tunnel Project is a high-priority, urgent project under construction by the Santa Clara Valley Water District in California. The project will provide a new low-level outlet for the Anderson Reservoir enabling the seismic retrofit of the Anderson Dam as mandated by the Federal Energy Regulatory Commission. This paper describes planning for construction of the tunnel through the dam’s right abutment crossing several faults in challenging and variable soft and hard ground conditions. The construction methods include SEM, hard rock drill and blast techniques, and a mechanized 8-foot (2.5 m) diameter microtunneled lake tap.

Dec 1, 2022

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994