Search Documents

By R. N. Edwards

The Magnetometsic Resistivity (MMR) method is based on the measurement of the low-level, low-frequency magnetic fields associated with non-inductive current flow in the earth. The traditional resistivity method maps the electrical properties of the earth by measuring the electric field caused by galvanic current flow between a pair of current electrodes. The MMR method differs from it in that the potential electrodes are replaced by a sensitive coil or magnetometer and a component of the magnetic field due to the current flow is recorded. The presence of an inhomogeneity redistributes the current flow which results in a perturbation of the electric field and, usually, of the magnetic field. The electric field immediately above a relatively conductive inhomogeneity must, by Ohm's Law, be smaller than that expected for a uniform earth. The current density in this region is also reduced but the current density within the inhomogeneity itself is enhanced so that the horizontal component of the magnetic field measured above the inhomogeneity is usually larger than that expected for a uniform earth. A method of interpretation using the magnetic anomaly was patented by Jakoskyl in 1933 but it met with little success at that time. Part of the problem was undoubtedly with the instrumentation, and only recently have robust instruments of sufficient sensitivity been developed2 and field data of good quality obtained. There are many common configurations of the potential and current electrodes in the resistivity method. Similarly, in the MMR method one or both current electrodes may be moved with the magnetometer, either horizontally or vertically ( in a bore-hole), or the current electrodes may be maintained in fixed positions and the magnetometer alone moved. The MMR anomaly is defined as the difference between the

Jan 1, 1975

By T. Wohlford

Due to the increases available base of scientific knowledge, increased independent review required by worldwide security exchanges, and the need for accuracy in characterizing mine water resources, it has become necessary to produce a more accurate hydrologic balance. This presentation provides a critical review of the steps and tools to compile a complete hydrologic review of a mine property. The forces of regulation, increased scientific analysis, better tools, and stakeholder expectations have created a perfect storm of accuracy demand. Ausenco has developed protocol to achieve the desired end.

Feb 23, 2014

By Stephen Utter

This report summarizes the results of preliminary investigations concerning the influence of block caving mining upon adjacent mine openings and discusses possible methods for reducing critical rock pressures and damage to these openings. These investigations are one part of a general study of the rock mechanics of block caving by the Denver Mining Research Center of the Federal Bureau of Mines. The purpose of this part of the study Is to obtain an estimate of the stress concentrations around mine openings adjacent to block caving stopes for use in developing better designed openings and improving mining methods. When mine openings such as slusher drifts, grizzly drifts, and haulage drifts are damaged by rock pressures induced by block caving mining, the mining cost increases, mine production decreases, and ore recovery may be consider- ably lessened. Methods of mining that result in lower rock pressures and methods of design that enable mine openings to withstand these pressures are desirable. The development of these methods, in turn, requires a fuller understanding of the following: The stres concentrations around the mine openings and the changes in stress induced by adjacent mining; the physical properties, such as the compressive strength and modulus of elasticity of the rock surrounding the openings; and the support supplied by the concrete lining, timber sets, or other types of supports used in the openings.

Jan 1, 1962

By M. Dayne Aldridge

A description is given of an experimental ventilation control system designed, built, and tested by WVU under United States Bureau of Mines sponsorship. A description is given of the control, system used and the mine-wide microcomputer-based ventilation monitoring system used with it. Test results of experiments conducted with this system at Eastern Associated Coal Corporation's Federal No. 2 underground coal mine are presented. In addition, a brief description is given of a new microprocessor based system presently being tested.

Jan 1, 1980

By Gary G. Grim

The reliable performance of the coal reclaim system is essential to the continued availability of a coal-fired electric generating unit. The control of fugitive coal dust within the areas housing the reclaiming equipment is necessary not only to minimize maintenance and clean-up costs, but is also a safety and health consideration. This paper describes the reclaim system control and dust suppression systems as initially installed, the shortcomings of these systems and the steps eventually taken to correct these shortcomings.

Jan 1, 1983

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By George E. Aiken

Agglomeration developments in the iron ore industry of North America are closely related to shifting patterns in commercially acceptable ore grades and even the definition of iron ores. These relationships have occurred mainly during the last 20 years. Many of these changes are an outgrowth of events which involved the history of the Mesabi Range. Although magnetic taconites had been discovered in the Lake Superior area about 1870, they remained unvrorked in part for lack of concentration methods and a generally unfavorable economic climate. Some 20 years later the rich Mesabi hematites were found beginning the era of direct shipping ores which continued through World War II. These Lake Superior iron ores included reserves of an estimated three billion tons. Following World War II, decreasing ore grades and rising costs began to force the closing of many underground iron mines. The early 50's saw the beginning of the decline in direct shipping ores and a spurt in produc- tion of natural iron concentrates. However, the market for unprocessed concentrates began to decline in the early 60's as agglomerated products and foreign ore s began to dominate the U. S. market.

Jan 1, 1973

By J. Gathje

Normal process development for pressure preoxidation treatment of refractory gold ores starts with laboratory batch autoclave tests, followed by operation of a continuous autoclave pilot plant for confirmation of the various process options. This scheme will generally provide good information showing the effects of such variables as grind size, time, and temperature, and will indicate whether autoclave preoxidation will produce solids that are amenable to cyanidation for gold recovery. However, several recent test programs conducted over the last three to four years have shown that the cyanide leaching responses of treated solids from the batch tests can differ considerably from those achieved by the continuous pilot plant autoclave. Examples are provided to demonstrate these differences and to show the importance of extending the laboratory investigations to include the use of a semicontinuous autoclave test procedure. A test case is cited in which this procedure provided data that could not be obtained from batch tests.

Jan 1, 1995

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By Ivan V. Klumpar

If components of a gas-liquid stream react with each other and with stationary solids, involving parallel and sequential, reversible and irreversible, and slow and instantaneous reactions, the process can be defined by a set of simultaneous differential rate equations and simulated as multistage semibatch re¬actors. Each stage is divided into finite time increments. Within each increment, even the simultaneous reactions are treated as sequential. The proposed method follows process evolution from non-steady state startup to normal operating conditions. It allows computing byproduct buildup in recycles, tracer response curves and, in case of underground processes, expansion to adjacent parts of the deposit.

Jan 1, 1979

By H. Y. Yang, L. L. Tong

For gold recovery, a Chinese refractory, high-sulfur gold concentrate was subjected to biooxidation with high pulp density in a single stirred-tank reactor. The flotation concentrate contained 36.9 percent sulfur (S) and 33.9 percent iron (Fe). Different experimental regimes for biooxidation were applied. With a mixed culture and by controlling the amount of addition of the gold ores and the pH of the biooxidation system, maximum iron oxidation of 82.6 percent and sulfur oxidation of 79.3 percent were achieved. The experimental results indicate that the pH control was beneficial to the biooxidation of this concentrate. Approximately 28.4 percent of elemental sulfur (S8) was found in the oxidizing slags. Two dissolution mechanisms of elemental sulfur are proposed: (1) FeS2 → S80 → S2O32− → SO42− and (2) FeS2 → S80 → SO42−. The high pH had a positive effect on the reduction of the S8. The results of thermodynamic analysis indicate that as an oxidant the dissolved oxygen can effectively reduce the Gibbs free energy of the pyrite oxidation process and, compared with the reaction of ferric iron as the single oxidant, the oxidation of pyrite is easier. The efficiency of the gold recovery was related to the iron oxidation as well as the sulfur oxidation. Gold and silver recoveries of 92.4 percent and 66.4 percent, respectively, were achieved.

By H. C. Siebert

According to the "Survey of Energy Resources 1980" (1)*, which was prepared by the Federal Institute for Geosciences and Raw Materials in Hannover (FRG)for the World Energy Conference 1980 in Munich, the world coal deposits are assessed at 775 billion tce proven reserves 448 billion tce of them recoverable and 6 161 billion tce additional resources. If one ignores growth rates, the current world coal output of 2,8 billion tpy gives our recoverable reserves a static life expectancy of 175 years. With an average increase in world output of 3,2 % like between 1973 and 1980 this range would be further shortened to an alarming degree. Furthermore, the criteria used to distinguish between workable and unworkable resources give rise to the suspicion that deposit characteristics are not always taken into account to a sufficient degree. For example, little attention is paid to major ?Bonitaet" - factors such as dip and seam thickness. There have been wide-ranging scientific discussions on the lower limit for workable coal resources, but no such limits have been set at the other end of the scale. Otherwise it is well known that performance and costs are badly affected den in level and moderately inclined seams the seam thickness is more than 4 to 5 m, because special mining methods have to be used beyond this limit. These are associated with significantly higher costs than with the winning of seams of ?normal? thickness.

Jan 1, 1985

By Thos. B. Douglas

In 1907, the Oklahoma Portland. Cement Company built a small dry process plant at Ada, Oklahoma, then Indian Territory. This plant was later acquired by the Ideal Cement Company of Denver, Colorado, who in 1918 built a new wet process plant along side the old dry plant. The older plant was later shut down .and eventually razed. In 1955, the Ideal Cement Company decided to increase the production at its Ada, Oklahoma operations. After many studies it was decided to build a complete new plant along side the old, near the site of the original 1907 plant. .The new plant was to have a. production of three million barrels annually while the plant then in. operation had an annual production of two and one quarter million barrels

Jan 1, 1961

By Velu Annamalai

In-situ uranium solution mining involves the injection of a lixiviant (leach solution) through appropriately placed wells into the underground ore zone. Upon contacting the uranium minerals, this solution will dissolve the uranium. The uranium containing solution is then pumped out of the wells into a processing plant where the uranium values are removed, typically in ion exchange columns, and the stripped liquor is recycled back into the field. The lixiviants may be acidic or basic. Where the ore zone mineralization contains appreciable carbonate, as in the South Texas fields, acid consumption would be excessive and the typical solution is ammonium carbonate bicarbonate at about 5-10 g/l and a pH of 7-9. Because the usual uranium minerals, uraninite or coffinite, contain uranium in the insoluble tetravalent state, it is necessary to add an oxidant to increase the valence to the hexavalent state where the uranium is soluble. Oxygen dissolved in the lixiviant has been shown to be quite effective for this purpose. It is also much more economical than other oxidants. Of concern is the possibility that (1) its solubility may or may not provide concentration levels adequate to give an economically attractive uranium level in the extracted liquor, and (2) the addition of oxygen in excess of the saturation level so as to increase the uranium grade in the lixiviant may cause gas blockage of the typical fine-pored ore formations.

Jan 1, 1981

By H. Kimura

A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. The process is based on the flash reduction of the concentrate particles in a gaseous reducing agent, such as hydrogen, natural gas, a reducing gas generated by partial combustion of coal, or a combination thereof. This technology is expected to drastically lower CO2 emission and reduce energy consumption by about 38% of the blast furnace requirements. The energy savings are possible largely due to the elimination of pelletization and cokemaking. Process design and simulation using hydrogen as the reductant for iron ore concentrate have been performed. A process flow sheet composed of a flash reactor, heat recovery system, water removal system for purifying recycled hydrogen, and all connecting streams was evaluated using the METSIM software. Ironmaking using two reactors was also designed and simulated, which could reduce the total required amount of hydrogen although it would increase the complexity of the flow sheet and operation.

Jan 1, 2010

By Ben W. Burdett

The operation of an electrolytic refining tank house is an art as well as a science. If the electro-refining industry is to progress, a better understanding of the refining process is necessary. This would help to reduce the amount of training necessary to produce competent tank house operators who, in turn, would be able to increase both quantity and quality of the tank house product. To aid in understanding this process, quantitative relationships between the critical tank house variables must be established. The inherent major contributor to inefficiency in most tank houses is short circuits. By quantifying the effect of short circuits on each of the other variables in the system, as well as their effect on over- all system performance, better decisions regarding manpower allocation can be made. Current distribution under short circuit conditions, which has always been somewhat of a mystery, can be studied in detail. The relative importance of electrolyte balance, proper anode-cathode spacing, low contact resistance at points of electrical connection, and other system variables can be determined, With a better understanding of these variables, the steps necessary to increase current efficiency are more easily defined. Relationships between most of these variables are described in qualitative terms in the literature, but quantitative relationships between tank house variables have never been established. A realistic mathematical model of the tank house could be used to test the effect of variations in a single variable on other variables in the system, and thus define the quantitative relationships between tank house variables. It is not the purpose of this paper to establish these relationships, but to describe a recently developed model that can assist in their establishment. A computer program implementing this model has been applied to examine the effect of short circuits on overall current distribution. Some of the results are given here as examples of the utility of this program.

Jan 1, 1973

By F. J. Susko

The Bureau of Mines investigated rapid bubble-pulp separation to improve flotation kinetics. A shallow-depth froth separator was employed to quickly recover the mineral-laden bubbles from a mixture of ore, water, and air bubbles. The shallow depth minimized the rising distance required to recover even the smallest size bubbles (100 ~m). Therefore, the slurry remained in the unit only long enough to recover the bubbles before the pulp exited through the conical bottom. Joining this unit with a rapid bubble-particle attachment unit, a rapid flotation system was formed that floated silica from phosphate in one-fifth of the retention time for conventional mechanical cells. The hydrodynamics of the rapid flotation system along with fundamental parameters for scale-up are presented in this paper.

Jan 1, 1992

By C. Gregory Knight

Adequate planning for the development, operation, and reclamation of a surface mine requires attention to present and future uses of land, both on the mine site and in the mine vicinity. This paper outlines land use implications of surface mining, and suggests procedures that could link mine planning, mine operation, and reclamation to more general land use concerns. Mining is viewed as a temporary use of land that may irretrievably commit land resources away from some future activities, but may allow other uses, some of which may have been impossible without mining. The paper accepts the premise that surface mining should attempt to minimize environ-mental damage and to maximize future alternative uses of land by appropriate reclamation. I. The Effect of Surface 1'1ining on Land Use Surface mining is a temporary utilization of the land most often criticized because the disturbances it creates are of far greater duration than the actual extractive operation, Resource recovery disrupts existing activity on the land, at least temporarily, and

Jan 1, 1977

By R. G. Church

Belle Ayr Mine was established in 1972 as the first large surface coal mine in the Powder River Basin of Wyoming. During the mid-1980s, it was eventually out-distanced in productivity by newer mines, and management recognized that the mine must recapitalize its major mining equipment and enhance its workforce flexibility in order to be competitive in the deteriorating market situation. Therefore, state-of-the-art haulage and loading equipment was placed into service, and a 12-hour rotating shift and a technician-based workforce was implemented. Belle Ayr Mine is located 29 km (18 miles) southeast of Gillette, Wyoming, in Campbell County (Figure 1). The mine is a part of AMAX Coal West, Inc., and with its sister mine, Eagle Butte, located 8 km (5 miles) north of Gillette, is a major contributor to the overall coal production of AMAX Coal Industries, Inc., headquartered in Houston, Texas. This paper addresses mine planning, recapitalization initiatives, and innovative workforce changes which propelled this large, surface coal mine to the forefront of productivity in the ever tightening low sulphur coal market.

Jan 1, 1994

By Chin Wei Yang

Linear programming (LP) has proven to be a most effective mechanism for modeling a vast array of practical problems, while the development of LP applications in engineering have been extensive enough to show its advantages and limitations. In this paper: we focus on the properties of the widely-wed linear programming transportation (LPT) model formulated and developed by Koopmans (1) . There have been many models of this type applied especially in the field of energy economics (2-7). Since most of these applications can be linked to the seminal work of Henderson (8), we stall present our discussions based on his work.

Jan 1, 1980