Search Documents

By Cyril W. Draffin

Introduction Americans have long been proud of their ability to recognize a need, define it, and then develop workable solutions. The U.S. underground coal conversion (UCC) program is a good example. In 1974, the need to utilize coal resources that could not be mined was recognized, and Congress gave the Bureau of Mines $1.7 million to gain a better understanding of the UCC technology and its potential applications. Since 1977 when the U.S. Dept. of Energy (DOE) was formed, workable technologies have been tested, the market for underground coal conversion has been recognized, and extensive industrial interest has developed. Perspective The U.S. is blessed with extensive coal resources. Coal supplies about 19% of our national energy needs, yet recently promulgated environmental standards and increasing mining costs have limited direct coal use. UCC potentially can use coal that is economically or technically infeasible to mine because the coal is too thick, deep, dirty, high-ash, and wet; has an excessive angle of dip; or has unpredictable and poor over-burden characteristics that make mining unsafe. Coal can be gasified underground or perhaps liquefied below the earth's surface. Underground coal gasification (UCG) is the prime element of the underground coal conversion program. It enables coal to be converted to gas underground. UCC Coal Resource Recent data show a total U.S. coal resource base of about 6.4 trillion tons. Of this, 1.8 trillion tons might be accessed by UCC, including some minable coal. A commercial UCC process could quadruple roughly the 450 billion tons of U.S. coal reserves, which presently are recoverable by mining. The U.S. coal resources are divided into five sectors. The two most eastern sectors contain relatively thin, swelling bituminous coals that are difficult to gasify. Of the two, the bituminous coal in the Eastern Province is the most difficult because it is deeper than in the Interior Province and the terrain is more rugged. The sector along the Rocky Mountains contains huge amounts of thick low-rank coals that are the most promising for early development by UCC. The coal has good continuity and the terrain is suitable. Low-rank coals such as subbituminous and lignite are highly reactive and tend to shrink and disaggregate when heated. Most of the coal in the Pacific

Jan 9, 1980

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abandoned coal mines also imposes potential hazards in current mining operations since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive man-made tunnels in previous work has led to the development of a surface- operated automatic earth resistivity survey system and associated computer data processing system for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to- diameter ratios greater than ten to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting coal mine workings. The hardware and software aspects of the new system are described together with applications of the method to the survey and mapping of abandoned coal mine workings. Field tests are presented showing the detection of both air-filled and water-filled mine workings.

Jan 1, 1981

By J. Herhold, S. Plaum

The focus within the economical optimization of projects, which are conducted underground, shifts more and more towards the conduction of construction work underground. Underground operations can be defined in a wide range of various projects, from underground mining tasks to the construction of engineering structures. Within these projects the conduction of construction work cannot only be defined as absolutely necessary, but sometimes also as optimizing for underground processes (e. g. installation of workshops underground to support the mining processes). Even though the conduction of underground construction might cause positive outcomes concerning the productivity, it also tends to be challenging due to local (sub-surface) conditions and influences. To minimize the risk of failure and sudden events within in the conduction of construction work underground, the tool “work preparation” shall be used. Under the given constraints, such as local influences, expected construction work and set time frame, the conduction of the construction work will be planned in advance by consideration of the construction logistics as well as the selection of a fitted construction technique. PROBLEM DEFINITION Economic Challenges - Raw Material Extraction Enterprises in the construction, mining and raw material extraction industries are increasingly under the pressure to perform economically to sustain their position on the global market. Profitability, efficiency and productivity are the basic conditions to be an active participant on the global market as well as a business partner and contractor for mining and construction projects or projects related to the extraction of raw materials. The completion of large-scale as well as common construction projects above ground has been under the pressure to minimize costs and time whilst maximizing the potential outcome, in the meanings of quality and economic gain, for more than a decade now. Whereas the construction industry has to fight the competition on the market with efficient project outcomes, the mining industry has to find ways to perform efficiently to further conduct the extraction of decreasing raw material deposits. The ongoing exploitation of existing raw material deposits to satisfy the constantly increasing raw material demands world-wide, led to the predicament that economically mineable deposits have decreased dramatically. Even tough mineral deposits do still exist on a global level, near-surface deposits decrease rapidly. Therefore, the extraction of raw materials within mining operations will be relocated further away from the surface in greater depths. With the growing distance from the surface to the mineral deposit, the extraction costs will increase many times over. With that in mind, the extraction costs will increase whilst the economic efficiency will decrease. The extraction of certain deposits will no longer be profitable with the common approach. To further extract raw materials efficiently even in greater depth, companies have to change their practice in different ways. That leads to the fact, if the deposits are in the depths, where the extraction processes won´t be economically, other (support) processes have to be in order to guaranty an economical corporate process itself. This precept will divert the focus from the actual mining process to support processes, where potential for optimization still can be found, as shown in figure 1.

Jan 1, 2019

By R. B. Hawkins

The discovery of the gold deposits of the Jerritt Canyon district and the construction of the E. R. Bell Mine is one of the significant mining developments in the United States during the past ten years. This mine will exploit one of the larger deposits of disseminated gold presently known, with proven, recoverable reserves in excess of 67.6 million grams of gold. Interest generated by the success of this project has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell Mine, is a 70/30 joint venture between Freeport Gold Company and FMC Gold Incorporated, both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan, Inc. and FMC Incorporated. Under the terms of the joint venture agreement, Freeport Exploration Company, another Freeport-McMoRan affiliate, manages the exploration and pre-mine development. Drilling, design, construction and management of the Bell Mine are provided by Freeport Gold Company.

Jan 1, 1982

By David W. Wisecarver

The U.S. Bureau of Mines, in cooperation with U.S. Borax and Chemical Corporation and the Kennecott Copper Corporation, has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of microseismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron Mine near Boron, California, and the Rimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nevada. Microsesimic noise rates in stable inactive mining areas are between 0 and 10 noises/ hour; the rates in stable active mining areas are between 10 and 50 noises/hour; and the rate in unstable areas is as high as 2500 noises/ hour. High microseismic noise rates in the Liberty Pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic tech¬nique is applicable to large pit walls, and that the wide band, wide range microseismic equipment appears to be suitable for open-pit investigations.

Jan 1, 1969

By A. W. Dickerson

Following on from many years of research aimed at improving the effectiveness of truck haulage operations in mines operated by BHP Minerals, BHP Research developed a concept for an Innovative Large Mining Truck, (ILMT) which has the potential to significantly improve the cost effectiveness of rear dump mining trucks. The ILMT concept reduces the empty vehicle weight dramatically, greatly reduces unequal rear tyre loading and improves ride and handling characteristics. The concept has been taken to the "proof of concept" prototype truck stage with the cooperative efforts of BHP Coal, BHP Research, Liebherr Mining Truck, Inc., Liebherr-Australia and Birrana Engineering. Testing of the prototype truck commenced at a coal mine in Queensland, Australia during May 1996. Preliminary results from the testing program are very encouraging. Expectations are being met and in some cases exceeded.

Jan 1, 1997

By R. Keith Evans

Potential large scale uses in secondary battery systems and fusion reactors together with a steady increase in demand for conventional applications, particularly in aluminum smelting, has resulted in an increasing interest in lithium and its compounds. Current world requirements are met from both granitic pegmatites and non-pegmatitic sources and although the emphasis in this short paper is on the pegmatitic minerals, and, in particular, on their "direct usage" applications, a short summary of other sources and requirements for chemical production is included for the sake of completeness.

Jan 1, 1977

By G. J. Joy, J. P. Rider

Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 30 m/min (100 fpm). This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the U.S. National Institute for Occupational Safety and Health (NIOSH) is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research (OMSHR) Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities — 152, 213 and 274 m/min (500, 700 and 900 fpm)— and at water pressures of 689, 1,034 and 1,379 kPa (100, 150 and 200 psi). Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Average reduction efficiencies of at least 90 percent were seen at the three sampling locations closest to the shearer for all three manifold systems at nozzle spray pressures greater than 689 kPa (100 psi). Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer, a spray manifold was fabricated and evaluated at an underground operation.

Jan 1, 2016

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Joy Global is helping to bring mining performance and analytics to the next level. By evaluating underground haulage, a significant component of the Room and Pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Joy Global is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way. These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer ‘nice to haves’, they are ‘must haves’. Starting with the best products and the right people is a first step, but then what? How do mines take their operations from just OK to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way. The fundamentals of operational excellence (OpEx) are based upon the DMAIC process, which stands for define, measure, analyze, improve and control. DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes; then improving the performance and controlling the operation. Joy Global uses Joy OpEx or ‘lean’ principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety. These same principles can be applied in most situations to streamline processes, improve operations and deliver value. As applied to mining, OpEx is seen as moving the needle on value creation by first identifying the value stream, then analyzing the areas that are not optimized. Once defined, these areas are ‘designed out’ of operational processes to create an automated operational flow. At a US coal mine, Joy Global was brought in to apply Joy OpEx principles to optimize mining and haulage to improve productivity and reduce costs. This multi-phase process started by defining the existing systems challenges to start finding areas for improvement."

Jan 1, 2017

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs. Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By Randall E. Hughes, John F. Burst

This chapter describes the nature and occurrence of the principal clay minerals that are used as ceramic raw materials, explains how these raw materials are used to produce finished goods, and summarizes positive and negative trends that will affect future demand for raw materials and products in the ceramic industry. The term ceramics was derived from the ancient Greek keramikos (a clay jar). A ceramic product is a material that has been fired to at least 468.3°C (Mitchell, 1983). In addition to being one of our earliest manufacturing and construction materials, ceramic products are among the earliest records of civilization. The enduring significance of ceramics is shown by the fact that, even today, the manufacture of whitewares, brick and related red-fired wares, refractories, and engineered ceramics continues to be a major sector of the US economy. A wide range of materials can be made into ceramic products, although relatively few earth materials make up most of the ceramics in today's markets (Table 1). Most ceramic products are made from clay or a related material. The long history of clay use in the ceramics industry stems from its variable and sometimes unique physical and chemical properties, as well as its ubiquitous occurrence and relatively low cost. Clay is important to ceramics because of its plasticity, moldability and filterability, chemical content, color. refractoriness, solubility. corrosion resistance, electrical properties, and other properties that result from the essentially two dimensional morphology of the individual clay mineral platelets. Because of their basic relationships to the chemical and physical properties of clays, the chemical and mineralogical content have been the subject of continuous studies over the past few decades. Advances in knowledge about the chemical, mineralogical, and physical properties of clays are responsible for most of the advances in processing. The need to remove off-colored contaminants, minerals with low melting points, and soluble salts has resulted in beneficiation by wet processing methods such as water washing. Water washing is restricted to kaolins, although low cost methods of water washing have been extended more recently to ball clays in Europe. High intensity magnetic filtration and flotation technologies have noticeably improved the quality of kaolins and broadly expanded their use in the ceramics industry. In addition to products for construction (e.g., brick, tile, sewer pipe, field drain pipe, cement, fiberglass, roof granules, and paint) and manufacturing (e.g., refractories, kiln furniture, sanitary ware, pottery, and dinnerware), clays are used in calcined form as ceramic fillers, carriers, extenders, and grogs. Ceramics suppliers are under economic pressure in several of these product areas. Manufacture of refractories in America has declined as steel production has decreased. Similarly, dinnerware and tile production have declined because of foreign competition. Fortunately, new uses for clays,

Jan 1, 1994

A kinetic model for leaching of various metals with different lixiviants in a batch system has been developed. Material balances for reactants and products at the solid/liquid interface were formulated and solutions to these balances were obtained in view of practical conditions. Special emphasis has been given to examine mixed controlled reaction systems where both heterogenous reaction and mass transfer play important role on the overall rate expression. The resulting kinetic expressions for either powder or rotating disc are discussed in light of experimental findings for various metals. Examples of the metal dissolution systems considered in this study include cobalt, nickel, copper and gold in acid, cyanide or ammoniacal solutions.

Jan 1, 1992

By C. Y. Chen

In order to put an end to the uneven environmental standards and enforcement established by various coal mining States in the United States, the Congress passed and the President signed the Surface Mining Control and Reclamation Act (Public Law 95-87 or the Act) on August 3, 1977. Within one year after passage, the Secretary of the Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for State regulatory programs under the Act and to allow States to assume primary regulatory responsibility. In order to implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules, but ones which take into consideration the distinct differences between surface coal mining and underground coal mining. The regulations developed by the Secretary and promulgated on March 13, 1979, with respect to subsidence control, included (1) a subsidence control plan as part of the permitting process, (2) substantive provisions establishing performance standards for subsidence control, and (3) provisions providing for the prohibition of mining under perennial streams, impoundments larger than 20 acre feet, and certain public facilities and urban areas.

Jan 1, 1985

By R. Owens, C. Roos, B. Hill, S. Rosenthal

It is common practice, and even legally required in many jurisdictions, to design two-lane haul roads in open pit mines to three and a half times the widest dimension of the haul trucks operating on the road. In open pit gold mines with high strip ratios, the road width has a significant impact on the economics of a design. It is possible to minimize the flattening of the highwall if the road width is reduced, assuming the width used is not needed to flatten the slopes for geotechnical purposes. With the use of autonomous haulage and pullouts, it may be possible to operate safely and efficiently on a reduced road width of two times the width of the hauling equipment.

Mar 2, 2022

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By Ernest L. Ohie

In 1939 the Geological Society of America published a summary of the geology of the ore deposits of the Mississippi Valley region, This volume, edited by E. S. Bastin, contained contributions from the foremost students of the area which described theregionalgeologic setting of the various deposits as wel as the detailed geology as then known. The various ideas as to the origin of the ores were discussed with the general, though not unanimous, conclusion that the deposits were hydrothermal products, Only those deposits in the immediate Mississippi Valley area were considered without any attempt to introduce evidence from other districts generally accepted as being of the "Mississippi Valley type." Since 1939, much new information has come from extended studies of two of the important districts described in the 1939 report andimportant extensions of the known ore have been found. Likewise, concentrated geologic efforts have been fruitful in severa "Mississippi Valley type" districts - both U. S. andforeign - not treated in the 939 paper. The wealth of new field information on the structural and stratigraphic relations of this interesting ore type, coupled with the results of theoretical and laboratory studies of the past 18 years, makes desirable a review of our present knowledge and interpretation of these important deposits which for many years have yielded over 20 percent of the world's annual production of lead and zinc, together with large amounts of fluorspar and barite. No restatement of the details of the geologic evidence willbe attempted here; the interested student is referred to the papers cited. Slide No. 1 shows the distribution around the world of the deposits under consideration. A principal thesis of my remarks is that there is so much similarity in all these deposits that it seems necessary for all of them to have had a similar mode of origin, whatever that may be. Variations in the shape, size and mineralogy of the orebodies give each district some individuality, but there are enough of the "typical" characteristics present in all cases to make classification in the "Mississippi Valley type" agreeableto most geologists. Thus the overall process giving rise to the ore solutions surely was the same for all in the group. Either they all have igneous affiliations or they all do not. Acknowledgment of this kinship between deposits in the various districts offers many advantages in trying to arrive at a decision as to just what the origin may have been, for the amount of guiding and limiting evidence which must fit into the hypothesis is greatly increased over that available in any one district, To a certain extent this was recognized by the authors of Special Paper 24 in treating all of the immediate Mississippi Valley areas together; by expanding the consideration to include ore deposits of this type all over the world the changes of success, i.e., arriving at the correct answer, are improved several fold. Since most of these districts are quite simple structurally, a number of hypotheses might fit the facts in any one of them, but if the facts to be met can safely be drawn from all the districts, then the explanations which will fit all the data are much less numerous. One purpose of this paper is to call attention to the field facts that have been reported from the .various areas which seem to have an important bearing on the kind of ore fluid that was responsible for the ore and on the way it circulated.

Jan 1, 1958

By Norman L. Kotraba

In Electric Arc Furnace (EAF) steelmaking, dust emissions are collected in a baghouse to prevent their escape to the Environment. This fine dust, predominantly iron oxide, also contains oxides of various other metals introduced into the EAF from the scrap charge. For example, mixed or galvanized scrap brings with it zinc, lead, and small quantities of cadmium which preferentially accumulate in the collected off-gas dust. Stainless steel scrap brings chromium into the charge, some of which also makes its way into the baghouse dust as hexavalent chromium-containing oxides. Because many of the contained heavy metal oxides are water-leachable, the U. S. Environmental Protection Agency has listed EAF dust as a hazardous waste which, as of August 8, 1988, cannot be 1andfi11ed without first being treated. Moreover, beginning August 8, 1991, all dusts with zinc concentrations of 15% or greater will be required to undergo high temperature thermal treatment to remove the heavy metals prior to any further disposal. This deadline represents several EPA-granted time extensions to the original requirements; extensions which were granted to allow for further development of process technologies.

Jan 1, 1991

By Edwin K. Maughan

The Rocky Mountain region contains part of the paleocontinental shelf that lay in Arizona and New Mexico through Utah, Colorado, and Wyoming into Montana and North Dakota. The shelf was bounded by the northeast-southwest-trending Transcontinental arch and the Cordilleran miogeocline in late Paleozoic and early Mesozoic time. Major tectonic features that affected middle Phanerozoic sediments on the shelf were the Big Snowy trough and Williston basin in the north and the ancestral Rocky Mountains in the central part of the region. The Zuni uplift and similar positive areas occurred along the axis of the Transcontinental arch in the southern part. The late Paleozoic and early Mesozoic sedimentary rocks record transgressive-regressive marine cycles in which the Cordilleran shelf and much of the adjacent craton were inundated by epeiric seas. Early in the Carboniferous, an epeiric sea covered most of the shelf. Greater topographic relief developed in Late Mississippian, was at a maximum in Middle Pennsylvanian, and then diminished through Permian and Triassic time. The development in the Pennsylvanian Period of horsts and grabens along northwest- trending faults on the northwest flank of the Transcontinental arch resulted in the ancestral Rocky Mountain system. The eastern part of the region was emergent by Middle Triassic, and the emergence lasted until Middle Jurassic, owing to uplift along the Transcontinental arch. During the early part of the Mesozoic, the sediments were dominantly terrigenous and were deposited mostly in shallow littoral marine environments shifting to continental. Most middle Phanerozoic structural elements within the area of the shelf are characterized by lineaments that have either an east-northeast or a conjugate north-northwest trend. The east-northeast lineaments closely parallel the northeast trend of the continental slope (miogeocline) in Nevada to southern Idaho. The conjugate set closely parallels the northwesterly continuation of the miogeocline north of an approximately right- angle bend in south-central Idaho. The northeasterly trending Transcontinental arch and the northwest-trending margin of the Canadian Shield are parallel structural elements with the north- east and northwest trends of the miogeocline. The rectangular lineament pattern on the shelf suggests a system of rectilinear fractures within the underlying Precambrian crystalline basement rocks that moved several times in the Phanerozoic in response to external forces applied against the continental crust. Movement of these blocks influenced erosion, deposition, and lithofacies of the sediments in middle Phanerozoic time. Zones of crustal weakness, represented by the lineaments bounding these blocks, probably were influential in localizing sedimentary mineral accumulations and petroleum deposits, as well as later igneous intrusions, volcanism, and emplacement of hydrothermal ores. Igneous activity in this region was rare during the middle Phanerozoic, but these conjugate fractures seem to have been avenues for later passage of hydrothermal solutions responsible for ore emplacement.

Jan 1, 2013