Search Documents

By Ted H. Eyde

Nearly 17 years ago a major producer of synthetic zeolites started an extensive exploration program for natural zeolite deposits which resulted in the discovery of over 170 occurrences in the western United States. A few years later several of the other producers and consumers of synthetic zeolites also started similar exploration programs. Since then, small quantities of natural zeolite minerals have been produced from at least 12 deposits in the United States. Of these the Bowie deposit, about 13 miles north of Bowie, Arizona, is the most important,having produced over 5,000 tons of vitric tuff zeolitically altered to the mineral chabazite and minor amounts of the minerals erionite and clinoptilolite. Mining Districts and Mineral Deposits of Arizona compiled by Charles A. Mardirosian, Consulting Geologist, estimates the value of the total production from the Bowie deposit at a very conservative $2,000,000. Unfortunately, none of the companies responsible for the discovery and the initial production of natural zeolites made any effort to develop the high volume, low cost applications of this unique mineral raw material. Instead, they developed only the high unit value uses to supplement their existing synthetic molecular sieve product lines. With the producers of synthetic zeolites thinking in pounds and not in tons, further development of natural zeolite deposits stagnated for over a decade.

Jan 1, 1974

By J. Morris

Petro-diesel is a common collector for fine coal froth flotation but partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DRO. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAHs were measured in tailings and concentrate streams, and coal recovery and ash rejection were tracked. Results show that concentrate waters consistently had higher DRO than tailing waters, and DRO in both streams generally increased with increasing diesel dosage. DRO again appeared to be limited to the WSF and PAHs tended to partition proportionately with DRO. Results indicate optimal flotation performance should generally coincide with minimal DRO partitioning to process waters. Under typical operating conditions residual DRO should not present an environmental concern; however, conditions should be avoided that allow significant overdosing of diesel.

Feb 23, 2014

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Respirable crystalline silica (RCS) found in dust generated by various mining processes is an important occupational hazard in the underground coal-mining industry. Exposure can lead to disabling and incurable diseases, including coal workers’ pneumoconiosis (CWP), silicosis and lung cancer [1,2]. Clusters of rapidly progressive CWP have been observed in the Appalachian regions of eastern Kentucky and southwestern Virginia, and recent cases have been generally more severe and showing more rapid progression. CWP is approximately four times as common among long-tenured underground coal miners in central Appalachia than long-tenured underground miners in the rest of the United States, and 20.6 percent of long-tenured underground miners in central Appalachia were suffering from the disease as of 2017.

By Klaus Beckmann

Gentlemen : My object reads "Longwall Rapid Advance of Coal Mining in the Federal Republic of Germany". It is true that the percentage of coal obtained in your country from longwall faces, with at present 1.2, is still rather low, but it increased considerably since 1966 with 0.4 %. The coal mines of the Federal Republic of Germany ever used longwall as the classical method of coal getting. All attempts to introduce bord and pillar mining did not lead to any wider application of this method. The principal reasons, for this appear to have been: - the deeper depth of our workings, - the wish to keep working losses as low as possible and to utilize the deposits opened up by deep and therefore expensive shafts to the furthest possible degree, - the dense sequence of seams and the mutual influencing of the working points, - the high number of disturbances in the geologically much stressed deposits, - and the necessary considerations to the protection of the densely built-upon surface.

Jan 1, 1970

By Anita Wu

"GENERAL BACKGROUND/CONTEXT The £300 million Bond Street Station Upgrade project will provide essential congestion relief and step-free access to an important interchange and destination station in the heart of the London Underground network. In 2010 London Underground (LU) let a design & build contract to Costain Laing O’Rourke (CoLOR), with the works to be completed in early 2017. CoLOR’s lead designer is Halcrow-Atkins JV (HAT). The station upgrade works comprise the following principal elements: •,A new satellite ticket hall on the North side of Oxford Street •,Two additional escalators and stairs providing congestion relief to the Jubilee line platforms •,Four lift shafts to provide step-free access between the different levels of the station •,Additional stairs to Central line platform level •,Tunnelled connection to the Crossrail station immediately to the south •,Connecting passageways, including ten connections to existing station tunnels. To achieve this, an existing property at 354-358 Oxford Street has been purchased and demolished, and the basement deepened to make provision for the new ticket hall. From this basement two circular shafts have been sunk, providing construction access for the tunnelled passages and lift and escalator shafts. The tunneling is principally in the London Clay stratum, which is widely recognized as a favorable tunneling medium, although the deepest parts of the works extend into the Lambeth Group strata which consist principally of stiff clays at this level but also contain water-bearing sands. The majority of tunneling has been carried out using mechanical excavation and sprayed concrete linings but other techniques have been used in areas where SCL is not practicable.A key challenge for design and construction of the works has been spatial constraint, in particular due to: •,The existing underground station layout •,The Limits of Deviation for the works •,The small construction site at 354-358 Oxford Street •,Overlaying Third Party assets including Listed buildings, sewers and water mains."

Jan 1, 2016

By K. Sasaki, W. Astuti, N. Okibe, T. Hirajima

"The kinetics of leaching of a saprolitic ore from Indonesia by citric acid solution under atmospheric pressure was investigated. An examination of the effects of leaching temperature, citric acid concentration, pulp density and ore particle size on the dissolution rate of nickel found that they all had significant influence on the rate. The highest nickel recovery (95.6 percent) was achieved under the leaching conditions of ore particle size of 212-355 microns, citric acid concentration of 1 M, leaching time of 15 days, pulp density of 20 weight/volume percent, leaching temperature of 40°C and shaker speed of 200 rpm. The shrinking core model was found to be appropriate for describing the leaching kinetics of this ore in citric acid solutions at atmospheric pressure. The experimental data were well interpreted by this model with rate of reaction controlled by diffusion through the solid product layer. Using the Arrhenius expression, the apparent activation energy for nickel dissolution was evaluated as 12.38 kJ/mol. Finally, on the basis of the shrinking core model, a proposed empirical kinetic model for the leaching of nickel from this Indonesian saprolitic ore was expressed as a mathematical model, which was verified as consistent with the observed experimental results.IntroductionIndonesia has some of the world’s largest nickel laterite reserves and was the largest producer of nickel – in the form of nickel lateritic ores – in the world in 2013 (Merchant Research and Consulting Ltd, 2014). However, only high-grade saprolites are processed in Indonesia using pyrometallurgical methods to produce ferronickel and nickel matte. Lower-grade saprolites and limonites are removed, becoming waste or overburden in mining site areas. Hydrometallurgical methods, involving either chemical leaching or bioleaching, are now seen as the most important technologies for treating nickel laterites in the future because of their advantage of not only extracting nickel and iron but also other valuable elements. In addition, hydrometallurgical methods consume less energy and have lower capital and operational costs. Although they are recognized to be more suited to limonites, some researchers have studied their use in the extraction of nickel and other metals from saprolites (Guo et al., 2009; Lu et al., 2013). Hydrometallurgical processes for the extraction of metals, especially nickel, promise to be meaningful alternatives to pyrometallurgical processes to primarily treat low-grade saprolites for which pyrometallurgical processing is not favorable"

Jan 1, 2015

By Edward C. Dowling

Froth flotation has been used industrially for many years to separate valuable minerals from their associated gangue constituents. Notwithstanding the significance of this process to the mineral industry, many of the engineering tools needed for the evaluation of the flotation process are still in a developmental stage. Traditionally, the evaluation of a flotation test on both the laboratory and industrial scale has been based largely on a rougher recovery value achieved at a sufficiently long time to give a "final" or "equilibrium" recovery value. The assumption of a time equivalency for a given recovery value between various flotation tests or between laboratory tests and industrial operation underlies this method of evaluation. Such an assumption implies that flotation is an "equilibrium engineering process" and that the time-rate recovery of material from the flotation cell is not affected by changes in the flotation system. It has been shown by Bushell (1) and by Klimpel (2) that the assumption of time equivalency between various flotation tests is unjustified. Consequently, better tools are needed for evaluating flotation test results, Because mathematical flotation models which incorporate both a recovery and a rate function can completely describe flotation time-recovery profiles, they can provide an excellent tool to evaluate flotation tests.

Jan 1, 1984

By J. A. Matar

Mineralization features at the Bajo La Alumbrera porphyry copper-gold deposit are discussed as they affect gold leaching and copper flotation behavior. Alteration-mineralization geological blocks are assigned in the zoned body, and each required its own geostatistical model. They extend horizontally outward from potassic to the phyllic-propylitic boundary, vertically from surface down to 300 meters, and include oxide, secondary enriched, and hypogene mineralization. Copper and gold values are calculated geostatistically from assays and all available geologic-mineralogic information. Reserves are classified for each geologic block and for each open-pit bench into leach or float ore according to metal grades, geologic characteristics, and supergene-hypogene relations. Finally ore extraction behaviour is briefly described, grouping gold and copper reserves into metallurgical families.

Jan 1, 1986

By H. T. McAdams

The logic of regression analysis as an operations research tool is critically examined, and a formal basis for its application to mining problems is developed. The traditional view of regression analysis as a statistical discipline does not provide an adequate basis for evaluating a regression model in a specific area such as ore reserve calculation or process control. In particular, the validity of the residual-sum-of-squares criterion is questioned, and the need for a criterion based on interpolative features of the model is emphasized. Strictly speaking, a regression model is statistically supported only at points at which observations are available, yet inferences are drawn with regard to a continuum. When considered as a mathematical function, therefore, the model is observationally defined only on a domain consisting of a finite number of points. Extension of this domain to an interval of the real line must be based on physical rather than statistical argument. Vector space and function theory concepts useful as a logical framework for a physically oriented problem analysis are discussed and their usefulness demonstrated in a practical problem.

Jan 1, 1966

By K. Schonert

Jigging is a separtion process that has already been described by Agricola in 1556. Fine size material is normally treated in a hutch jigging process, in which the heavy particles are penetrating the jigging bed and are recovered in the hutch. In this process, a ragging consisting of the same or higher specific gravity particles is inserted upon the screen. The ragging is used mainly as a valve to maintain a constant upward flow of the water. Since the heavy particles should pass easily into the hutch, the ragging particles are up to ten times larger than the maximum feed size (1). In the fine size range - 1 mm the performance of jigs is mainly insufficient; some of the low density particles percolate the ragging while the hutch water flow prevents the fine heavy particles from entering the bed (2). By giving a thin layer of particles, which posesses a density sensitivity in case of certain adjustment of flow conditions, directly on the screen, the precision of separation can be increased. Stroke length and frequency have to be adjusted to give this filter layer a homogenous porosity between 60 and 70% during the pulsion phase, and the "en masse" lifting of the bed, as it is known in jigging of coarser material, has to be prevented (3). In this case, the jig cycle is only of minor influence.

Jan 1, 1987

By José Mujica, Mónica Campos, María Fe Campos

The extraction and processing of metals and other minerals have played an important role in economic, political and social development worldwide, from the early stages of prehistory to the present day (Gosner, 2020). Mining has been a fundamental part of human civilization, providing the raw materials necessary for technological, infrastructure and industrial advances. As society progresses, the importance of mining continues to grow, supporting the development of everything from the smallest electronic devices to the tallest skyscrapers (Escamilla, 2024). The economy of a nation is connected to its extractive industries (Moreira and McMahon, 2014), which have seen dramatic growth in recent years (Pietrobelli et al., 2018). In a context of increasing demand for natural resources, driven by the development of emerging technologies, the expansion of infrastructure and the foundation of engineering achievements for the coming decades (Minerals Education Coalition, 2024), mining should focus efforts on global development, requiring a comprehensive approach to sustainability that addresses the planet’s needs and protects the well-being, primarily, of the communities and environments where mining operations take place (Figari, 2024). In these areas, diversity and inclusion should be promoted, thus fostering equitable and sustainable development. The sustainable development goals (SDGs), also known as the global goals, could serve as a key framework for fostering a strong social management culture in mining. The SDGs were adopted by the United Nations (UN) in 2015 as a universal call to end poverty, protect the planet, and ensure that all people enjoy peace and prosperity by 2030 (United Nations Development Programme, n.d.). Companies have compelling reasons to align their actions with the SDGs, as their long-term success depends on healthy communities. This is a major challenge that requires collaborative efforts (Singh and Rahman, 2021). As Fraser (2021) mentions, achieving more sustainable outcomes may involve mining companies and communities working together collaboratively. This article proposes an innovative approach: Inclusive mining for sustainable development, which aims not only to maximize economic profitability but also to promote social and environmental well-being by integrating the UN’s SDGs, primar)ily focused on diversity and inclusion. This can be achieved through the implementation of a key value-added initiative for mining companies: the creation and operation of a corporate volunteering program aimed at developing and executing inclusive practices to promote gender equality, the inclusion of local communities and indigenous peoples, and accessibility for people with disabilities. This proposal will educate employees and stakeholders about sustainability and promote concrete actions through corporate volunteering to strengthen the mining company’s commitment to community development, improve social relations and advance toward achieving the UN’s SDGs, establishing the company as a global change agent.

Nov 1, 2025

By C. D. Litton

This paper describes two new gas diagnostic techniques which have been used successfully to determine: 1) the combustion status of underground mines which have been sealed due to fire (Littol1 Ratio); and 2) the location of fires in abandoned, underground mines or waste banks (Kim Ratio). The Litton Ratio makes use of the rate of change of CO, calculated on both an air-free and methane-free basis, from mine gas samples and compares these values with those expected from a normal, combustion-free environment. The Kim Ratio uses the concentrations of total hydrocarbons, C2 ?C5, less the methane, to arrive at ratio values which increase as combustion intensity increases. The details of these two new techniques, their application to real situations, and their limitations will be discussed.

Jan 1, 1989

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011

By Robert R. French

Commercial grade gypsum beds up to 16 feet thick is present in southwestern Indiana. The major deposits are found at a depth of 350 feet to more than 500 feet below the surface. The ore body averages about 75 to 95 percent gypsum. Two companies are currently exploiting a deposit which underlies an area of several square miles near Shoals, in Martin County. Another deposit has been located in southwestern Owen County but has not been developed. The Indiana Geological Survey is currently drilling in Greene County and is considering further exploratory work in Perry end Dubois Counties.

Jan 1, 1965

Laboratory tests were conducted in a full-scale continuous miner test gallery to evaluate resulting dust levels for changes in face airflow, spray water quantity and pressure, and mining height. The minimum and maximum values tested for each parameter were as follows: airflows between 1.42 and 6.14 m3/sec, water flows between 56.8 and 132.5 lpm, nozzles pressures between 413 and 1379 kPa, and mining heights between 1.52 and 2.74 m. Each of these parameters were evaluated for four common spray system designs. Respirable dust samples were collected in the operator's cab on the miner and in the immediate return. Second-order polynomial models were used to represent expected dust levels and multiple stepwise regression was used to identify significant control parameters for inclusion in the models. Separate models were developed for dust levels at the operator and return locations and for each individual spray system. Interaction between control parameters and curvature effects were found in most models. The analysis indicated that at the operator location, airflow and mining height had the most significant impact on respirable dust levels. In the return, airflow and water pressure were typically the most significant parameters. The models developed for each spray system design can be used by mine operators to guide application of control parameters for a variety of operating conditions and mining heights.

Jan 1, 1994

By Dale R. Andrus

Why is there such an increased thrust toward positive multiple use land management and where will it lead? History and purpose of the mining law of 1872. John Marshall discovered gold at Sutter?s mill near Coloma, California, on January 19, 1848, and utter chaos resulted. The great migration of people to the undeveloped western lands had begun. Prior to this discovery, copper, lead, and iron had been the minerals for which the laws were made. With this discovery of gold on the public domain, it became apparent that congressional legislation was necessary. This became even more apparent as each of the numerous mining districts which were springing up in California, and elsewhere in the west adopted local miners' customs to regulate their activities. Although these early miners acted under mining district rules and in some cases state regulations, they were, in reality, appropriating minerals without sanction of federal law.

Jan 1, 1970

By Barbara J. Arnold

A coal's size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.' s (formerly EPRI' S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By G. S. Dobby

The Cu-Au flotation cleaning circuit at Freeport Indonesia consists of three stages: two flotation column stages, in series, followed by one stage of mechanical cells. Concentrate from both column stages is combined as final concentrate. The mechanical cell stage has two parallel rows of seven Wemco 500's. The Wemco concentrate is recycled to feed of the second column stage and Wemco tails report to final tailings. This paper examines cleaner circuit performance, focusing on size-by-size performance of the individual stages and the individual mineral groups -copper sulfides, gold and in sol minerals. The recovery mechanisms of insol minerals are examined.

Jan 1, 1995

By C. Van Landingham, A. Bailey, R. A. Schoof

A residential metals abatement program has been underway in Butte for more than 20 years. More than 1,350 yard and attic cleanups were completed by the end of 2018; most triggered by lead. While the focus is on remediation of residential soil and house dust, the program also includes a blood lead monitoring program with identification and abatement of additional sources of exposure for children with elevated blood lead levels (BLLs). As specified in the remediation program, studies are being conducted every 5 years to assess BLL data collected from Butte children. The first two studies have evaluated over 6,000 BLLs from 2003 through 2017 and evaluated trends over this time period, by Butte neighborhood, and as compared to areas outside of Butte. These studies showed that rates of elevated BLLs (i.e., those above 5 µg/dL) in Butte children have declined dramatically since 2002 but have been declining much more slowly since 2011. Improved rates of confirmation testing are needed to verify the rates of elevated BLLs. While the RMAP likely has contributed to these declines in BLLs the magnitude of impact cannot be quantified.

Mar 2, 2022

By Hou Xilun

Three production methods of rapid cold bonding and low temperature bonding pellets using sponge iron powder as a binder have been successfully developed. These methods differ from ordinary bonding method by no addition of salt and other catalyzers, no corrosion of equipment and no pollution of environment. Mechanism of pellet bonding is studied. Experiment shows that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the production of metallic pellets continuous and stable. These methods are substituted for traditional high temperature firing of oxidized pellets in direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved. Production cost may also be decreased. The production of cold bonding pellets does not need additional area.

Jan 1, 1980