Search Documents

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By J. Launay

In order to control and dispatch the sewage water coming from 3 tunnels toward 2 downstream sewage tunnels, a large cavern has been excavated in a suburb of PARIS. Located at a depth of 47,00 m, it has been excavated using the NATM procedure through swelling clay, weathered sandstone, and marl and chalk. It is 16,50 m high, 12,40 m wide and 60, 00 m long, with an elliptical cross-section and its two ends are egg-shapped. The final lining of the cavern is composed of 30 to 40 cm of shotcrete, steel ribs and passive anchor bars. The excavation stages and related movements were surveyed by extensometers, pressure cells and convergence devices. The design, method of construction of the cavern and the results of the measurements made are commented.

Jan 1, 1989

By Saul J. Esdalera

The flotation response to amine collector and its adsorption on the mineral surface was studied as a function of pH and collector concentration. The flotation response increased in the order anorthite + intermediate plagih clases + albite, while adsorption of amine obeyed the Freundlich equation r = A.Cn. This adsorption is proposg to be due to a covalent bonding between the AlOH surface pups of the plagioclase altered outer layer and the amino group of the collector. Finally, the study showed thatmtial dissolution of the solid phase provides the necessary conditions for amine attachment on the mineral particles and consequent flotation.

Jan 1, 1980

By Ross Glanville

The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR cam also be expressed as the Optimum Mime Life (OML) in years since the expected mime life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mime life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mime life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low¬-tonnage mines (such as many underground gold/silver deposits) often lead to sub¬optimal results. In fact, am apparently uneconomic deposit at am arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mime' properties based on arbitrary production rates.

Jan 1, 1984

By Leslie G. McMillion

A field project to develop and demonstrate a method for alleviating problems of highly-mineralized ground water where they occur as isolated zones or pockets in fresh-water aquifers is being conducted in the Ogallala Aquifer of eastern New Mexico by the Robert S. Kerr Water Research Center. Removal of contaminated water is by a large-capacity well and the pumped poor-quality water is used locally for secondary recovery of oil, Benefits of the operation are threefold in that the aquifer is being reclaimed for future fresh water production, contaminated water is being used beneficially, and fresh water which otherwise would have been used for waterflooding is available for other purposes. Ground-water quality in the site has improved markedly after 21 months of operation. Water quality in 15 specially-drilled monitoring wells has returned to the original quality level of the aquifer, and chloride concen¬trations in the pumping well have dropped to half the maximum level recorded thus far. Project results are very favorable and provide guidelines for initiation of similar undertakings in localities where needed.

Jan 1, 1970

By R. W. Bartlett

High salinity geothermal brines typically contain up to several hundred parts per million of valuable heavy metals, and because of the large potential flow of geothermal brines from future power plants, metal production as a by-product could be significant A-planned 55-MW demonstration plant near Niland, California should generate enough spent brine to contain approximately $670,000 per year in gross metal values. Lawrence Livermore Laboratory estimates (1) a Salton Sea Geothermal potential of 1300 to 8700 MW, which would translate to possible yearly heavy metal values between $5,800,000 and .$l05,000,000. Since these estimates were made on a conservative basis, this geothermal reservoir is potentially a large ore deposit. The heavy metals in order of decreasing abundance in high salinity brines from the Salton Sea geothermal field are usually manganese, zinc, iron, lead, and silver. All but manganese and iron are valuable enough to be of commercial interest. Minor amounts of copper and arsenic are also present. Although heavy metal precipitates, particularly lead, have been found in scales within pipelines and obtained from steam flashing, most of the metals remain soluble during steam production; hence removal of the valuable metals from the spent brine before reinjection in ground reservoirs is indicated. Because the heavy metal concentrations are low, a very simple and inexpensive process is required. The heavy metal value in Niland brine is only ' about $1 per 1000 gallons; see Table 1. The brine composition shown in Table 1 was taken from one of the brine samples used in our study. Projected post-flash brine from a steam plant has somewhat higher Zn and Pb values, but the gross heavy metal value is still less than $2 per 1000 gallons.

Jan 1, 1980

By G. S. Dobby

High-intensity wet magnetic separators have been successfully introduced into the mineral processing field over the past ten to fifteen years, due largely to rapid advancements in magnet design. Wet magnetic separation, until recent years, was applied solely to the concentration of minerals of high magnetic susceptibility, such as magnetite, at relatively coarse sizes. Now, however, high-intensity separators are capable of treating weakly paramagnetic minerals and have extended the range of treatable particle size down to about one micrometre(1,2). . One of the more recent-high-intensity separators developed is the Kolm¬Marston Marston type high-gradient magnetic separator (HGMS) (3,4) It consists basically of an iron-clad solenoid surrounding a matrix material - a fine, ferromagnetic steel wool or expanded metal lath. A schematic diagram of the device is shown in Figure 1. Large, highly localized, pertebations of the magnetic field are created by the ferromagnetic matrix. It is these field gradients that are instrumental in developing large magnetic forces which act on the mineral particles. Operation of the separator is simple. Slurried sample is fed through the matrix and, depending upon the mineral parameters of particle size and magnetic susceptibility and. the operating parameters of flow rate, field strength and feed weight, some particles will be attracted to and adhere to the magnetized matrix, while the others will flow through the matrix. The separation is completed by later removing the background magnetic field and flushing the captured mineral particles into a separate container. The process can also be applied on a continuous basis (S).

Jan 1, 1977

By P. Somasundaran

Previous studies on semi-soluble minerals such as calcite (1) and apatite(2) and sparingly soluble minerals such as quartz (3,4) have given evidence for significant changes in their electrokinetic properties as a function of aging time. Such changes are relevant to mineral processing operations where the crushed ore particles might not have yet reached equili¬brium with the water that it is in contact with. In order that these changes be studied under controlled experimental conditions for long periods unattended or with fairly less intermittant attention, a streaming potential apparatus with an automatic streaming system was constructed. Also, a new streaming potential cell was incorporated into the system so that the effect of temperature, a variable coming into increasing usage in mineral processing operations(5), could also be studied. Conventional streaming cells(6) cannot be safely employed to conduct studies as a function of temperature since they have many glass joints that are prone to leakage, parti¬cularly under pressure, in the course of an experiment. This paper describes the new apparatus and some typical results that have been obtained with it far temperature effects.

Jan 1, 1973

By Lana Alagha, Keitumetse Cathrine Monyake

The abstract discusses the synthesis and investigation of polyacrylamide functionalized chitosan polymers (CS-PAMs) as selective depressants for pyrite in the flotation of galena and chalcopyrite from complex sulfide ore. The study employed response surface methodology (RSM) to model and optimize the flotation process, varying parameters like the degree of deacetylation of chitosan, weight ratio of chitosan to acrylamide, and CS-PAM dosage. The developed RSM models effectively predicted iron and lead grades and recoveries, while optimization showed optimal pyrite separation from galena and chalcopyrite using CS-PAM synthesized from chitosan with a high degree of deacetylation and a specific chitosan:acrylamide weight ratio.

Apr 9, 2022

Coal has traditionally been an integral part of life in Kentucky. Coal mining produces a large part of revenue for the Commonwealth of Kentucky and provides a significant number of jobs to the residents of eastern (less in western) Kentucky. Recently, however, the coal industry of Kentucky has had to endure many hardships. The Clean Air Act set forth sulfur dioxide emission standards which have severely affected much of the coal mining industry in Kentucky, because much of the coal mined in Kentucky has a high sulfur content. In this paper, the background around the effects of Clean Air Act on the coal industry is introduced. The economic and social effects of the Clean Air Act on the Kentucky coal mining are addressed.

Jan 1, 1993

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By Ratnakar Singh, Raj Kishore, Kisor Kumar Sahu, Ranjeet Kumar Singh, Ganesh Chalavadi

The Falcon concentrator is capable of separating minerals in fine size classes based on their differential density. Separation of mineral particles depends upon the fluid flow characteristics and relative movement of particles in a fluid. In the present study, a fluid flow characteristic inside the Falcon concentrator was established through experimentation and modeling. The Falcon concentrator has two fluid entry points: (a) Fluid entering through gravity assisted feeding system and (b) Fluid entering through the fluidized hole on the concentrator wall. In order to identify the role of fluid entering the concentrator, a tracer was injected into the system. As per the tracer based experimentation, it was established that fluid entering through the gravity based feeding system is responsible for thin flowing film formation in the stratification zone where particles are stratified based on their relative density. The momentum balance and continuity equations were simplified for a high centrifugal force field, and the fluid velocity profile was estimated inside the thin flowing film. Estimated fluid flow profiles will help to simulate the particle trajectories inside the Falcon concentrator. The influence of rotational speed, fluid flow rate, and cone angle on the fluid velocity profile were investigated. Fluid thickness over the concentrator wall is also estimated, and it is typically of the order of ~150–200 μm.

By W. R. Reed

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

Jan 1, 2008

By T. H. Dubaniewicz, J. E. Chilton

The U. S. Bureau of Mines is investigating the application of fiber optic technology to methane and carbon monoxide monitoring. A methane monitoring system is described that is based on differential absorption of infrared light. It can detect concentrations as low as 0.2% and as far away as 2 km via fiber optic cable. The upper range is 100% methane. The system requires no electrical power within the mine so it should operate safely under mine disaster conditions. A hybrid carbon monoxide monitoring system is described that combines a low-powered electrochemical cell with fiber optic telemetry. Testing has shown the system can operate maintenance- free for several months.

Jan 1, 1992

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By J. D. Crone

Crone Geophysics Limited in co-operation with Newmont Exploration Limited has developed a ground Pulse electromagnetic method. This is the first unit in a planned integrated system of surface and borehole Pulse EM equipment. Newmont had previously developed an operational Pulse EM unit for use in areas of very high surface conductivity. The Newmont equipment was large, heavy apparatus that required motorized transport. It operated in the equivalent frequency spectrum of 10Hz to 2.5Hz. The basic aim of Crone Geophysics was to design a Pulse EM system more portable than Newmont's. We wanted to operate in all types of field conditions including heavily wooded and mountainous terrain areas. We also wanted to record the higher frequency information that is contained in the Pulse EM waveform. There are three reasons why we thought this high frequency information was important in survey applications: (1) Field tests conducted over massive sulphide bodies in the Arizona desert showed that the desert weathering process tended to break down the electrical contact between sulphide crystals. The net effect is to reduce the conductivity of a massive sulphide body, particularly narrow bodies or highly fractured sulphide zones. In order to detect such occurances the higher frequency information is essential. (2) We wanted to be able to detect occurances with sulphide content as low as 5% sulphides that are usually poor to moderate conductors. (3) We also wanted to be able to determine the presence and extent of surficial conductive formations and clay deposits since many airborne EM anomalies are caused by such bodies. If we have the capability of detecting and recognizing these formations we would be able to explain the airborne anomaly.

Jan 1, 1976

By Elwyn King, Donald J. Dodds

"...Unfortunately, the research activities in soil mechanics had one undesirable psychological effect. They diverted the attention of many investigators and teachers from the manifold limitations imposed by nature on the application of mathematics to problems in earthwork engineering. As a consequence, more and more emphasis has been placed on refinements in sampling and testing and on those very few problems that can be solved with accuracy. Yet accurate solutions can be obtained only if the soil strata are practically homogeneous and continuous...." This statement about soil mechanics was made by Karl Terzaghi, thirty years ago and applies to a greater degree today to the infant science of rock mechanics. More uncontrolled variables are added to the already many existing in soil mechanics. Variables, such as Macro-discontinuity and in situ stress levels. In no other field of engineering are the problems as site oriented. Presently this site dependance demands the investigator or rock mechanics engineer to get his hands dirty rooting in the muck of a tunnel floor trying to properly install or readout test apparatus in a comprehensive site investigation. This paper discusses such a site investigation designed to determine the problems and solutions inherent in the driving of the Trans Koolau Tunnel. The paper will describe the various types of tests to be performed, how the results are to be used and the interrelation of the various tests themselves.

Jan 1, 1997

By Y. C. Guan

The dissolution behavior of silver and copper form their elemental states and Ag/Cu alloys in ammoniacal solutions has been studied using rotating disc electrodes. The variables studied included concentration of ammonia, oxygen partial pressure and rotating speed of the disc. The results have been interpreted in terms of the mixed potential theory. The effect of local current resistance on the overall current has also been examined as a part of the governing theory of the dissolution. It was observed that the dissolution potential and the rate of dissolution were very much affected by the composition of the alloys.

Jan 1, 1995

By Keith Olson

In the heart of Appalachia, where coal mining has shaped communities and economies for generations, Bluefield State University (BSU) has made a landmark decision to reestablish its mining engineering technology program. This move comes at a critical juncture for both the university and the mining industry, which faces significant workforce challenges amid evolving technological demands and an aging professional demographic. The program’s revival represents an educational initiative and a strategic response to industry needs and regional economic development. Nestled in the mountains of southern West Virginia, BSU has a storied history intertwined with the region’s mining heritage. The institution’s decision to bring back this specialized program after a hiatus of several years signals a renewed commitment to serving both regional industry demands and providing career pathways for students in an area where the cyclical nature of resource extraction economies has often limited economic opportunities. “This program’s return reflects our deep understanding of this region’s needs and our commitment to preparing graduates for meaningful careers that support our local industries,” said Darrin Martin, president of Bluefield State University. “We’re bridging the gap between education and industry with a modernized curriculum that addresses today’s mining challenges while preparing for tomorrow’s innovations.”

Jun 1, 2025

By L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly. However, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics—namely, size and location—are of great importance in reducing the risk of mine fire injuries. A new, improved fire location algorithm has been developed and integrated into an atmospheric monitoring system (AMS) program by researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve the detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.