Search Documents

By David Mast, Irwan Halim, Seung Han Kim

Fermilab is constructing a large underground cavern in Limestone to house scientific equipment. The cavern will have a complex L-shaped geometry and about 215-foot depth with relatively shallow rock cover, with service/egress shafts accesses into the cavern. Three-dimensional analytical models were developed to study the ground behavior and support performance. Multiple rock constitutive and failure models were evaluated. The models were significantly impacted by the high lateral in-situ earth pressure at the site. This paper will describe the design approaches that were taken to optimize the cavern arch geometry to allow safe construction in shallow rock, and permanent support requirements.

Jun 13, 2021

By K. Y. Haramy

A scale-invariant theory of the strength and deformability of rock masses in static equilibrium and at incipient failure is proposed. The theory provides a rationale for designing structures in rock. This paper presents results of experiments conducted by the U.S. Bureau of Mines and theoretical methods to determine and interpret in situ strength of rock masses using the borehole shear tester.

Jan 1, 1995

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

By T. Panhorst

Evaluation of through-deck blasthole sample reliability at the Lone Tree gold mine revealed a non-systematic bias in the sampling system. Ore is primarily hosted within the Powerline fault zone. Clay gouge, present in the fault zone and typically enriched in gold content, forms agglomerates during blasthole drilling leading to a segregation error during sampling. Replicated samples split from blasthole cuttings piles show through-deck samples to be either significantly enriched or depleted by 1.5 standard deviations or more from the mean gold content of their respective cuttings pile quality of through-deck samples correlates strongly with quantity of clay present.

Jan 1, 1999

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By Robin P. Gardner

The mechanistic approach to comminution consisting of incorporating particulate breakage functions into a suitable population balance equation has been developed by a number of researchers over the past decade or so. (1) To date this approach has been developed and demonstrated primarily for batch-operated, laboratory or small-scale ball mills. However, since industrial mills are mostly quite large and operated in the continuous mode; suitable population balance models and methods for obtaining the necessary breakage and other model parameters must be developed. This paper describes and investigates a radioisotope tracer technique for this purpose, Population balance models previously developed(2,3) are adapted for this study.

Jan 1, 1974

By P. M. Hawley

Kennecott Corporation, in joint venture with Galactic Resources Ltd., recently began operation of an open pit gold mining and milling facility near Columbia, South Carolina. The deposit consists of two ore bodies (North and South deposits) hosted in deformed and altered meta-volcanics and meta-sediments of the Carolina Slate Belt. This paper describes the rock mechanics and engineering geology investigations conducted for design of interim, ultimate and final reclamation slopes for the South Pit. Emphasis includes the successful use of drill core orientation techniques to confirm complex geologic structure at depth; the development of a three-dimensional rock mass competency model, incorporating surface mapping data, results of bench mapping documentation, field index testing and laboratory testing; and kinematic assessments for design of optimum slopes.

Jan 1, 1991

By Jürgen Kretschmann

Principally, mining natural resources is a finite business that reaches its limits once the deposits mined are depleted, the resources can no longer be mined in an economically profitable way or substitutes are pushing the mined products out of the market. An example of the latter is the increasing replacement of coal with natural gas and renewables in power generation in the United States [1]. According to the model of the product lifecycle, the global hard-coal mining industry has reached a stagnation phase [2]. The trend is obvious. Coal use peaked in 2013 [3], and the coal demand of China has been slowly decreasing since then [4]. Coal consumption in the United States saw a 16 percent decline from 726 Mt (800 million st) to 608 Mt (670 million st) between 2015 and 2019. In addition, according to the U.S. Energy Information Administration, it will not rise again [5]. The decline is attributed to complex market dynamics, from low gas prices because of the “shale gas revolution” [6] to federal environmental regulations like the Clean Power Plan. Moreover, important players like the United Nations and the European Union have already begun to describe pathways toward decarbonization. Increasing competition between coal-mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries, like France, Spain or Germany, are only forerunners of this development — their centuries of coal production have passed. The concept of sustainable development (SD) is fundamentally based on a model of progress in which ecological, economic and social dimensions should be developed equally and positively. Questions arise, such as: How can SD be a corporate goal in a phase of decline? How can former mining regions sustainably progress to a better future? The steps Germany has taken to handle the coal decline in a sustainable way and the lessons learned from this process are described in this paper. 

By Ralph E. Magnuson

The quality of our environment is of great importance to all of us. Today, there is a great public concern about the degradation of our air, land, and water and the resultant slow death of our planet Earth. The miner has always been concerned with his environment. Historically, mining has been a part of the frontier. As a result, the miner has pioneered and developed many parts of the world. In the beginning, he had to hack out a place for his mine, himself, and his family. He was given accolades and praise for his accomplishments. Now, however, he is attacked as a ravager of the landscape. It was and is no different on the Marquette Iron Range in Marquette County, located in the Upper Peninsula of Michigan. Iron ore was discovered in 1845 and mining was begun by 1848. Over nearly 1 ¼ centuries, a total of 379,197,000 tons have been shipped to market. Ports, docks, railroads, and towns all had to be built in order to get that tonnage out to iron and steel makers. In those early days the environment had to be mastered, not pampered.

Jan 1, 1970

By P. Rusin

Toxic substances in On solutions can retard biological leaching of copper sulfide dump ores. On solutions were analyzed for metals, organics, and chloride, and showed inhibitory concentrations of aluminum, manganese, and chloride. Inhibition of bacterial activity by the solid fraction of On solution, with and without the organic constituents, was evaluated. Toxicity to bacterial species was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50 -60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different SX reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost effective and the least toxic.

Jan 1, 1994

By A. P. Schissler

2013 has seen metals, industrial minerals, and coal all reduce in price due to market and geo-political factors. Many companies are taking write-downs to recalibrate their reserves and have enacted focused cost reduction programs. The public domain includes statements where companies have operating cost reduction goals in the $500 million range. Zero-base staffing & budget analysis is a means to achieve optimal employment and cost levels for a given level of production. The method involves measuring the work to be done similar to Lean. Lean is a method to review each step of production and remove anything that doesn?t add value or is necessary to complete finished goods. Zero-base methodology has been applied to mines worldwide producing realistic and sustainable levels of staffing and costs based on the quantity of work. The objective of this paper is to provide the framework of zero-basing with examples of application.

Feb 23, 2014

By Circe Verba, Scott Montross, Jon Yang

This work is a first-order study to assess the suitability of an organic acid lixiviant to extract rare earth elements (REE) from coal preparation fines refuse sourced from a Pennsylvania mine with a total REE of ~ 300 ppm. The extraction of REE using an organic acid, in this case 0.1Mcitric acid and 0.5Mtrisodium citrate solution, is compared against 0.5M(NH4)2SO4, 1MHCl, 1.2MH2SO4, and 0.5Methylenediaminetetraacetic acid (EDTA). Ashing the coal waste material prior to leaching tests with the citrate solution nominally improved REE extraction. Buffered citrate solution recovered 7% of the total REE in the as-received Isabella Fines as compared to 11% in ashed samples, whereas (NH4)2SO4 extracted 5–6%, respectively. EDTA recovered up to 33%of the total REE, most likely due to the higher coordination chelate bond. Mineral acids, however, outperformed the organic acids on ashed material (16–52%REE recovery), suggesting that organic acids may not be a suitable competitive option for REE extraction from these types of feedstocks.

Jun 15, 2021

By J. García, B. Arango, F. Calderón, O. J. Restrepo-Baena, A. Carreno, L. Rojas-Mendoza, J. Pérez, E. Bedoya

"Tungsten extraction is a subject of global interest due to is properties. These properties, such as its high melting point, have contributed to the development of metallurgical extraction processes that can be adapted to the particular chemical composition and mineralogy of the ore. In Colombia there is a research deficit in tungsten related areas, and especially with regard to its extractive metallurgy. In this study the physical, chemical and mineralogical characterization of a sample were performed. Subsequently, crushing and grinding were employed to reduce the material to a more convenient size, making it suitable for further concentration and metallurgical processes. Through physical concentration techniques it was obtained a concentrated ranging between 60 -70 % of WO3 content.INTRODUCTION Tungsten is a metal of great economic importance due to its excellent properties such as high density and extraordinary melting point 3422°C), which is indeed the highest of all the elements. Tungsten is primarily used in metal alloys, manufacture of special steels, coatings and catalysts; products of interest to both international and national industry. However; given that the use and economic value is determined by the percentage of tungsten in the mineral, particle size and chemical associations, it becomes essential to properly characterize the mineral to further define possible metallurgical extraction routes. The metallurgical processes for minerals enriched in tungsten may vary depending on location and the genesis of the ore body, which means that for each ore a particular set of operating conditions must be determined. This is important since process standardization can lead to misuse of the mineral resource. However, in Colombia there is a research deficit as it relates to minerals enriched in tungsten and to its extractive metallurgy. Then, there is a need to conduct studies that can lead to a better understanding of the ore, and to develop extraction processes for the metal of interest. EXPERIMENTAL A state of the art review was made in order to gain insights of the tungsten metallurgical process. Comminution was necessary with the aim to reduce the sample size; therefore the sample was taken into crushing and grinding stages. Concentration techniques such as magnetic separation, gravity and / or electrostatic were also applied. Physical, chemical and mineralogical characterization were performed by using polished sections, grain size determination, X-Ray Fluorescence (XRF) and X-ray diffraction (XRD) techniques."

Jan 1, 2015

By M. H. Bolu

Since undergoing a major mill expansion in 1979, Canada Tungsten Mining Corporation Limited has successfully operated a somewhat unconventional rod mill/rod mill grinding circuit at its mill in Tungsten, N.W.T., Canada. The concentrator employs two rod mills in series, of unmatched size and horsepower, for production of feed to a gravity (tabling) circuit. Cyclones and screens are closed circuited with the secondary rod mill. Outlined in this paper are the rationale behind, and consequences of operation of this unusual grinding and classification configuration.

Jan 1, 1984

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996

By G. P. JADAUN, ANINDYA PAIN, Aditya Rana, SAURAV RUKHAIYAR, N. K. Bhagat

This study compares three different techniques — decision tree, artificial neural network (ANN) and multivariate regression analysis (MVRA) — for predicting blast-induced ground vibrations in some Indian tunneling projects. The models’ performance was also compared with site-specific conventional predictor equations. A database consisting of 137 vibration records was randomly divided into training and testing sets for model generation. The results indicate that the decision tree is best suited to predicting vibrations. Furthermore, the decision tree suggests that the intensity of near-field ground vibrations is mainly affected by the total charge fired in a round, whereas the intensity of far-field vibrations is governed by maximum charge per delay and charge per hole.

By Gerhardt A. Bennewitz

The mechanism shown here (Fig. 1) may not be all that it appears to be. To many of you it may look like a hopper car, a thing of mobility, in which you would ship coal, ores, limestone, or other bulk materials. It is approximately 50 feet long, 12 feet high, and can be placed on tracks which are on approximate 14 foot centers. But far too often in the past, and all too often today, this mechanism has been made to serve as an immobile storage box, with its primary role -- the transportation of products, seemingly incidental to the storage function. Our engineering training teaches us to conserve resources, despite some of the popular and misconceived philosophies being advanced these days. Those of you who work for companies with traffic departments know that they are always striving to reduce the price which is paid to move your mine products. Today, let's consider and analyze the ways in which the cost of transporting your mine products might be reduced, based on particular reference to coal. Bear in mind that in this context, cost and price are not necessarily synonymous. Until a few years ago, most coal and other bulk materials handled by railroads moved under standard tariff rules. These rules, which still exist today, provided transportation vehicles (railroad cars) for extended periods at no added price to the shipper or receiver. "Normal" free time rules would permit a car to be held for a maximum of 48 hours without charge; however, in the case of coal, there is a rule which, subject to liberal rules as to the

Jan 1, 1972

By James B. Meredith

The European Economic Community (The Common Market) is now shifting from I a coal oriented to an oil oriented economy. The proportion of energy supplied by oil has increased from only 13% in 1950 to 38% in 1962, and will approach 50% by 1970. In the past five years Common Market petroleum demand has in- creased 15% per year compared with only 3% per year in the United States. This rapid shift to oil can be explained by looking at oil's competition, First; there is simply not enough other energy - European coal, natural gas and hydro-electric power - to meet the demand, Secondly, oil?s primary competing energy in the Common Market is coal, and Community coal is high-priced - it costs more than two and a half times as much as U. S, coal at the pithead. The third reason for the shift to oil is consumer preference for the ease of handling, convenience and cleanliness of liquid fuels. As these reasons suggest, much of the shift to oil and the resulting growth in demand would have occurred whether or not the Common Market organization had existed. On the other hand, the Common Market has stimulated the use of oil by causing a higher rate of energy consumption, and oil has been the beneficiary of most of this growth.

Jan 1, 1963

By A. V. Castelli

Since the record year of 1981 through 1985 the tonnage of weighting materials (barite and other heavy minerals) used in drilling fluids has decreased an estimated 49%. As in the past, barite still makes up over 90% of the minerals used for weighting materials in drilling fluid. Domestic production of barite has decreased 69% since 1981 and imported barite has made up over 50% of the total barite consumed since 1982. See Figure 1 for usage of barite. The number of operating grinding plants has decreased from 69 in 1982 to 39 at the end of 1985. With the decrease in demand of weighting materials for drilling fluids and an over capacity of grinding existing, prices for weighting materials have decreased dramatically. Although the American Petroleum Institute has not changed any of the specifications for barite, some users have initiated their own new specifications and have proposed to have them included in the API specifications. The exploration for and development of oil and gas dictates the level of weighting material used in the drilling fluids industry. Most forecasters do not foresee (or predict) increases in the level of drilling until the 90's. The primary or unground barite produced in the U.S. mines has a difficult time competing with imported barite due to the location of the mines. These mines are located in North Central Nevada, with small tonnages being produced in California, Missouri, Illinois, Montana and Washington. The major reason, is the difference in transportation costs from the mines versus ocean freight rates from the foreign ports to the major area of use, the U.S. Gulf. Since 1981, the production of primary barite has decreased from 2,849,000/ST (2,584,596/MT) in 1981 to an estimated 890,000/ ST (807,403/MT) in 1985(1). If it were not for the use of unit trains by some producers the production of primary barite in the U.S. would have probably declined another 20% in 1985. During the same period, of the total amount of barite consumed in the U.S., imported barite ore increased from 417, in 1981 to 65% in 1985. The major exporting countries to the U.S. during this period were China 46.27, Morocco 15.27., Chile 10%, Peru 8.4%, India 7.9%, Mexico 5.4%, Thailand 3.9% and Ireland 2.3%.

Jan 1, 1986

Adequate ventilation of coal mine working faces is the single most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. Bureau research has shown that to control respirable dust you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane the most effective approach has been to use a blowing brattice or tubing and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present, Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan-powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray fan controls methane on exhaust-ventilated sections.

Jan 1, 1988