Search Documents

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016

By S. Park

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing less hydrophobic particles to drop off. A bubble-coarsening model has been developed by calculating the changes in Plateau border area as a function of the initial bubble size at the base of a foam, liquid fraction, and foam height and then relating the predicted Plateau border area to the critical rupture thickness of lamellae film. The model predicts that bubble coarsens with increasing froth height, decreasing frother dosage, and decreasing aeration rate. The model predictions are in good agreement with actual bubble size measurements.

Feb 23, 2014

By Marc. A. Meyers

The analysis of the phenomena involved in the determination of the compressive strength of iron-ore agglomerates leads to the identification of the important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compression axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments is due to internal voids of varying sizes, that act as stress-concentration sites. Two novel testing procedures are proposed. The first consists of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents significant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1981

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

By C. B. Manula

The Crushed Stone Industry plays an important role in Pennsylvania's mineral economy. During 1965, the total production of crushed and broken stone in the United States reached 780 million tons from which 57 million tons were produced in Pennsylvania (Mineral Industries Surveys, 1966). It is further significant that Pennsylvania is the nation's leading crushed stone producer. Future trends in stone production will quite likely parallel those in the construction industry. Stone and stone products are finding greater and more varied uses each year. Continued record expenditures for structures such as dams, highways and buildings are the prime reasons for this accelerated growth in demand. Completion of the interstate road system and the maintenance of Pennsylvania's already expanded highway system form the essentials for this expanding market.

Jan 1, 1968

By C. J. B. Dreyer, H. A. Robinson

Only South Africa can be considered in terms of resources of amphibole asbestos. There are two asbestos producing fields, one in the Northern Cape Province (producing only crocidolite), and one in the Eastern Transvaal (producing only amosite). This chapter discusses the banded ironstone sequence in which amphibole asbestos occurs, and the genesis of the fiber is briefly reviewed. Also, the properties and characteristics of amphibole asbestos are discussed and compared to those of chrysotile. Approximately 300 000 t of arnosite and crocidolite are produced annually. Crocidolite has a potential for a fivefold increase of production chat could be sustained beyond the year 2000. An estimate of the resources of the various producing fields in South Africa is made. The mining methods are also reviewed and evaluation techniques are discussed. The only two types of amphibole asbestos exploited at present in South Africa are amosite [the white colored amphibole asbestos) and crocidolite (the blue colored asbestos). As is well known, crocidolite has been mined in South Africa from the early part of this century, and amosite since the early 1930's. Since these dates, asbestos mining has developed into a significant mining industry. The annual production of crocidolite is approximately 170 000 to 200 000 t. and amosite production is in the region of 80 000 to 100 000 t. CLASSIFICATION OF AMPHIBOLE ASBESTOS Four types of amphibole asbestos are produced economically in the world today: (1) crocidolite, the fibrous equivalent of riebeckite, (2) arnosite, the fibrous equivalent of grunerite, (3) trernolite, and (4) anthophylite. The names trernolite and grunerite apply equally to the crystal and fibrous forms of these minerals. For comparison and clarification purposes, the six known varieties of asbestiform minerals known in the world are shown in Table 1. All the asbestos minerals were originally developed as cross fiber seams in veins or fractures, or were controlled by the lithology. Post- fiber effects caused slip, sheared, and folded fiber seams. Crocidolite and amosite occur in banded ironstone of early Proterozoic age of the Transvaal Supergroup. The fiber seams are developed in certain defined lithological units in the banded ironstone sequence. The lithological units have a remarkable lateral persistence with respect to their chemical nature and physical appearance. Vertically, the banded ironstone sequence displays a heterogeneous nature. Commercial Applications The features and properties that make amphibole asbestos commercially attractive are: 1) The long average length of the fibers is good for greater wet strength in composites. 2) The high tensile strength of crocidolite makes it superior to all other types of asbestos. 3) It is characterized by dispersion in most liquid media, particularly amosite in water. 4) Since the surface charge of amosite and crocidolite is negative, the fibers produce an open lattice work in water with a high bulk volume giving excellent filtration rates and rapid drainage in a wet asbestos cement mix. 5) The insulating properties of amphibole asbestos mats are still important, particularly in a corrosive environment, despite the introduction of many other synthetic insulating materials. 6) Corrosion resistance, particularly acid corrosion resistance. 7) Due to the high modulus of amphibole fibers, resins reinforced with these fibers exhibit

Jan 1, 1986

By Donald S. Bubar

The Separation Rapids property, located approximately 60 km (37 miles) north of Kenora, Ontario, Canada, is host to one of the largest rare metal pegmatite deposits in the world. This pegmatite was named the Big Whopper by its discoverer, Dr. Fred Breaks of the Ontario Geological Survey, because of the exceptional length and width of the surface exposure. The property is readily accessible from a main, all-weather road via a network of secondary logging roads. The main line of the Canadian National Railway passes through the village of Redditt, just 40 km (24 miles) south of the property. The Big Whopper is one of the complex-type (petalite sub-type) class of rare metal pegmatites that are geochemically the most highly evolved in the spectrum of granitic pegmatites. Such deposits are economically important as resources for the rare metals lithium, tantalum, cesium, and rubidium. While complex-type pegmatites are found in many areas of the world, most are too small to be profitably mined, however, with an inferred resource in excess of 15 million metric tons (mt) (17 million short tons [st]), the Big Whopper is only the fourth deposit of its type in the world with the size required to be of major economic importance. The other three deposits, which are currently in production, are the Tanco mine in Manitoba, the Bikita mine in Zimbabwe, and the Greenbushes mine in Western Australia. The Big Whopper is situated in the eastern continuation of the Archean Bird River greenstone belt which also hosts the Tanco pegmatite, approximately 60 km (37 miles) to the west. The principal commodities identified in the portions of the Big Whopper pegmatite explored to date are petalite (LiAlSi4010) and rubidium-rich K-feldspar. These are industrial minerals with important applications in the glass and ceramics industries. The Big Whopper also contains substantial quantities of lepidolite, a lithium, rubidium-mica which is the principal ore mineral for rubidium metal. Tantalum and cesium occur in anomalous levels with the petalite mineralization, and the possibility of finding zones of high enrichment in these valuable high-tech metals elsewhere in the deposit is excellent. Such enriched zones are typical of pegmatites as highly evolved as the Big Whopper. To date, the geological mapping and diamond drilling work completed by Avalon have delineated the Big Whopper pegmatite system over a strike length exceeding 1.5 km (0.9 miles), over widths ranging from 10 m to 80 m (30 feet to 260 feet) in thickness, and to a vertical depth of close to 300 m (1,000 feet), where it remains open. The pegmatite system consists of a vertically oriented massive petalite pegmatite dyke striking 280 degrees that is flanked by amphibolites containing a swarm of narrower albite and petalite dykes which have all undergone intense deformation in a high strain zone resulting in folding and intense shearing. The Big Whopper exhibits a mineralogical zonation pattern which is complicated by the superimposed deformation that has both folded and stretched the deposit. Drilling has defined a dilute geological resource totaling 7.1 million mt (7.8 million st) grading 1.283 percent Li20, 0.346 percent Rb20, and .007 percent Ta205 over a strike length of 600 m (2,000 feet), and to a vertical depth of 250 m (820 feet), where it remains open. The petalite and rubidium-rich-K-feldspars contained in the Big Whopper all appear to be of superior quality. The grades are consistent with a petalite content averaging 25-30 percent and a rubidium-rich-K feldspar content averaging 15-20 percent. The remainder of the rock consists mainly of albite, several types of mica, and quartz. Accessory minerals include columbitetantalite, cassiterite, apatite, garnet, and gahnite. Market studies show that the deposit is located close enough to existing transportation infrastructure to access rapidly growing, major markets in the glass and ceramics industries, both in the northeastern U.S. and Europe. There are only three competing lithium minerals producers in the world with the Bikita mine in Zimbabwe being the only major producer of petalite. The other lithium deposits produce spodumene, a less desirable lithium mineral. Lakefield Research Limited has successfully designed a process to produce an ultra-pure petalite concentrate containing up to 4.65 percent lithium oxide, and as little as 0.014 percent iron oxide, low levels of soda and potash, and negligible amounts of other trace elements. With these specifications, Avalon will have an excellent quality product for glass-ceramics applications such as Corningware®, CERAN® stove tops, and other thermal shock-resistant products. Lakefield is presently designing the balance of the flowsheet to produce separate concentrates of rubidium-rich K-feldspar, albite, mica, tantalum, tin, and high-purity quartz. Initial test work indicates that the feldspar products will be of exceptional quality. The K-feldspar concentrates contain 11-12 percent K20 and 1 percent Rb20, while the sodaspar contains over 10 percent Na20, and both have very low iron (0.01 percent Fe203). A preliminary economic model shows that with an initial production rate of 90,000 mt (100,000 st) per year, expanding to 170,000 mt (190,000 st) per year over 5 years, the project is capable of generating over CDN $10 million per year in pre-tax cash flow by year 5 on a capital cost of approximately CDN $30 million.

Jan 1, 2001

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By Carl E. Brechtel, Edward D. Thimons

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kw (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1987

By Mark J. Logsdon, Barbara Basse

Mississippi Valley Type Pb-Zn deposits are widespread in the midcontinent U.S. and have been mined from the 1800's to present. Some tens of thousands of acres of mined land in the Tri-State District have been designated as Superfund sites as a result of surficial mine wastes and ground waters with elevated levels of metals. EPA considers the surficial mine wastes to be hazardous and a major source of acid mine drainage fAMD) that degrades water resources and threatens human health and the environment. To mitigate potential risks at one site near Galena, Kansas, a group of mining companies who had been identified by EPA as Potentially Responsible Parties IPRPs) proposed subgrade disposal of the mining wastes in shafts and subsidence features. However, this proposal was challenged by the Agency on grounds related to AMD and the potential for degradation of ground water quality. The PRP team developed a program of materials characterization, laboratory-scale leaching, and finally large-scale, pilot testing in the field. Static and dynamic leaching tests at both laboratory scale fusing artificial rainwater under both variably and fully saturated conditions) and field scale (using pH 4.5 ground water) showed that the surficial wastes do not produce acidic leachate and are not a long-term source of metals. Laboratory chemical and mineralogical tests show that the mine wastes contain substantial carbonate, but very limited iron sulfides, consistent with the leach test results. EPA "characterization" tests fEP Toxicity and TCLP) compare very poorly with tests simulating the expected leaching conditions. While these tests would classify the surficia1 wastes as "hazardous, they do not characterize the behavior of the high-volume, low-concentration, coarse-grained materials with respect to environments and disposal options of interest. To be meaningful, characterization of mining wastes must be performed in a manner that simulates the environmental conditions that are actually of interest with respect to a specific decision, such as subgrade disposal in the saturated zone.

Jan 1, 1991

By Richard C. Fox

"Why geophysics? We will have to drill anyway." Reliance on geophysical methods for detailed target appraisals will increase as direct surface evidence becomes more subtle. This will create a need for more effective and efficient geo- physical programs. Numerous computer-based techniques that deal with a broad range of geophysical problems are described in the literature. The purpose of this chapter is to provide a framework for the systematic application of these techniques to effect an overall optimization of the geophysical appraisal. The concepts described are not technique specific, but should serve as a guide for increasing the effectiveness and efficiency of any geophysical program. Fig. 1 shows a generalized flow chart of the major aspects of the program described. The three main subdivisions of a 'geophysical program are discussed: (1) survey design, (2) data processing, and (3) data interpretation. Detailed flow charts, outlining the goals, the requirements for meeting the goals, and the steps followed within each subdivision are presented at the beginning of each section. The objectives and type problems of each subdivision are defined, followed by a description of applicable computer methods. . References are cited that give a general cross section of computer techniques available in the literature, and examples are given in each subdivision to demonstrate basic concepts and the use. of computers in solving the type problems.

Jan 1, 1979

By J. Helton, J. L. Bellanca, M. McNinch, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation. INTRODUCTION Pinning, crushing, and striking accidents are a large problem in underground coal mines, especially for mobile haulage. Between 1984 and 2014 there were 179 non-fatal and 42 fatal pinning, crushing, and striking accidents involving mobile haulage vehicles, including coal hauling machines and scoops [1]. Proximity detection systems (PDSs)—automated systems that decelerate and stop a vehicle in order to prevent a collision—have the potential to protect mineworkers in these situations. In fact, PDSs are now required on all place change continuous mining machines as of March 16, 2018, as a result of the final rule published in January 2015 (30 CFR 75.1732) [2]. To address mobile haulage, later in 2015 the Mine Safety and Health Administration (MSHA) also proposed a new rule that would require PDSs on mobile haulage vehicles [3]. Though there has been no additional actions related to the proposed rule and it is not currently required, mobile PDS can still help to save lives. MSHA estimates that the adoption of mobile PDSs could prevent approximately 70 injuries and 15 fatalities over the next 10 years [4]. As of June 2015, the underground coal industry had already equipped 155 of the 2,116 mobile haulage vehicles in use [1]. In order to capitalize on the projected safety gains afforded by PDSs, it is important that the systems are designed and implemented effectively. Along with others, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been exploring PDSs for more than two decades [5-7]. Throughout this time, NIOSH has also held several stakeholder meetings (2010, 2014, 2016, and 2017) in order to disseminate information and provide an opportunity to discuss on ongoing issues and concerns. Despite some progress, human factors remain a key concern. Previous research examined mineworkers’ attitudes towards PDSs on continuous mining machines [8] as well as how continuous miner operators’ perceptions of risk have changed as a result of PDSs [7]. However, stakeholders have still expressed a need to better understand how mobile PDSs affect the mining process, the mineworker, and whether and how they may present previously unidentified risks.

Jan 1, 2019

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By J. W. Merks

Spreadsheet software is an effective tool for simulating dynamic stochastic systems such as mineral processing plants. The two-product formula is used to show how to set up a Monte Carlo simulation in a spreadsheet template and how to calculate variances of dependent variables. The key to a reliable and realistic simulation model is to obtain unbiased estimates for all independent variables and variances in the set that defines the stochastic system. Monte Carlo simulation is also a powerful tool for optimizing sampling procedures, for applying sensitivity analysis and for designing and evaluating experiments.

Jan 1, 2000

By B. Cavender

Mining managers trying to rapidly reduce production costs tend to implement a traditional set of topdown managerial practices: reductions in production volume, employee layoffs, renegotiation of supplier contracts, cancellation of employee training, restrictions on travel, reductions in office supplies, and so forth. While these practices do reduce costs, the benefits are often limited in both magnitude and duration, and the workforce is usually left demoralized. Successful cost-cutters take a different approach. They make the continuous reduction of costs a priority for all members of the organization, whether managers or workers. The culture of these firms emphasizes the commitment, voluntarily given, of individuals and work groups to this goal. Cost-cutting practices often reject all of the traditional methods mentioned above, but are far more numerous, innovative and successful. This culture of cost reduction is the result of a set of leadership competencies that establish direction for the organization, align the organization's various constituencies with this direction, and motivate and inspire the organization. Cost reduction then becomes a routine task rather than a heroic achievement.

Jan 1, 2002

By X. Cai, L. Jiang, G. Fu

A process for recovering manganese from low-grade manganese oxide ore through a reduction acidolysis-selective leaching method is investigated. Two types of biomass, sawdust and straw, were used as reductants. Reduction acidolysis, using concentrated sulfuric acid, was used to disrupt the structure of the biomass, allowing the biomass to be hydrolyzed into monosaccharides. Analysis by X-ray diffraction revealed that Mn2O3 was reduced to MnSO4. Then, in the selective leaching process, iron was removed through the formation of goethite. The optimized experimental parameters are as follows: reductant to ore mass ratio of 0.4, sulfuric acid to ore mass ratio of 0.9, water to ore ratio of 0.5, aging time of 18 h, leaching temperature of 95 °C, leaching time of 90 min, and solution pH of 2.5 to 2.8. Under these conditions and using sawdust as the reductant, the manganese leaching efficiency and iron removal efficiency were 91.8 and 99.2 percent, respectively.

By Jeff Salai

The CP-3A contract is the final segment of the MWWST’s 28.3 km (17.6 mile)pressurized water supply tunnel for the metropolitan Boston area. The 1,288 m (4,226 feet) of U-shaped tunnel alignment passed through five rock zones employing four different primary support systems. The short tunnel began in Weston, Massachusetts, at Shaft 5A in soft, completely weathered argillite, passed through a fault zone, and ended in Dedham granite. An 18-foot diameter horseshoe starter tunnel was built to accommodate a 4.94 m (16-foot 2 1 / 2 inch) diameter Robbins TBM. Heavy water inflows were anticipated and subsequently encountered during probe drilling. Pre-excavation grouting was implemented at high pressures to displace high water inflows in the starter tunnel and consolidate the fault zone. This paper will provide an overview of the tunnel construction with an emphasis on ground control, grouting and survey control.

Jan 1, 2001

By Musa D. Manzi, Raymond J. Durrheim, Richard T. Masethe

An investigation into the source mechanism of mining-induced seismic activity plays a vital role in understanding the various modes of failure observed in the underground deep-level South African mining environment. The seismic events data for this study was captured by the mine-wide seismic system operating at Kloof Gold Mine. This system comprises 40 4.5 Hz tri-axial geophones sampling at 6 kHz installed at locations that surround the stopes mining the Ventersdorp Contact Reef (VCR), Main Reef (MR) and Kloof Reef (KR). A set of 103,753 mining-related seismic events (-3.0≤ ML ≤2.7) that occurred during 2017 and 2018 was selected for this study. The mining depth of these seismic events ranges from 1600 – 4200 m; most located close to stopes mining the VCR ore body. The main criteria used to select a subset of events for detailed analysis were the number of stations that recorded the seismic event and the azimuthal distribution of the sensors.

Apr 26, 2022

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010