Search Documents

By Morton Handelman

The extraction of aluminum oxide_ from its ore is the initial step in the commerical production of metallic aluminum. This is most commonly done by the Bayer Process in which a caustic solution is used to dissolve hydrated alumina from the insoluable materials with which it is associate in bauxite. At the two-thousand ton per day Sherwin Alumina Plant of Reynolds Metals Company, the extraction residue from Caribbean ores is removed from the main pro¬cess stream as the underflow of a continuous clarifier-thickener operation. This sludge, prior to its ultimate r4jection from the process, is washed in a nine-step continuous countercurrent decantation system to recover physically-entrained mother liquor. Control of alumina production costs requires the optimum recovery of solubles from this residue which is generated at the same rate as the finished product. The equipment, operating techniques, controls and process variables which affect the efficiency of this soda recovery from Bayer Process red mud will be discussed.

Jan 1, 1959

By Z. Rogovin

A Knowledge of the amount of time the material spends in a continuous mill in a closed-grinding-circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of tracers in residence-time-distribution (RTD) experiments. In a typical wet process the RTD measurements are usually done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article a simple to use mathematical method for the calculation of the closed circuit material residence time in the mill is developed. Using this method there are no restrictions on the location of the tracer injection or detection points. Any convenient location in the closed circuit can be chosen without affecting the simplicity of the method. This method also enables the calculation of the degree of mixing in the mill. The use of this method for the analysis of impulse response data obtained from several commercial grinding circuits is presented.

Jan 1, 1986

By P. H. S. W. Kulatilake

The presence of discontinuities strongly affects the mechanical and hydraulic behavior of rock masses. Joint geometry networks play a vital role in civil, mining, and petroleum engineering projects associated with jointed rock. The need for a realistic representation of joint geometry in rock masses has been recognized. The first part of the paper shows how to build three-dimensional stochastic joint network schemes and also shows how to perform validation studies for these schemes using joint data from the Stripa mine, Sweden. Due to the existence of complex joint patterns, mechanical behavior of jointed rock masses usually exhibit scale effects and an-isotropic properties. A correct understanding of the mechanical properties (strength and deformability) of jointed rock masses is important for designing and performance estimation of structures build in and on rock masses. Beyond a certain volume, the mass proper-ties of the rock may remain essentially constant with respect to the effect of joints. This minimum volume may be used as the element size to represent the equivalent properties of a statistically homogeneous rock mass volume which contains a significant number of joints. This volume may be termed as a "Representative Elementary Volume" (REV) and may be of great importance for engineering purposes. Investigations are underway at both the 2D and 3D levels to look into the possibility of establishing relationships between REV mechanical properties and joint geometry parameters. Recently developed joint geometry modeling schemes are linked with existing distinct element codes (both 2D and 3D) to create a stochastic/deterministic stress analysis approach in achieving the goal. Results obtained so far in this direction are presented in the second part of the paper.

Jan 1, 1992

The Xinglongzhuang Coal preparation plant project was a joint effort by American and Chinese engineers and for the most part designed to American standards. The plant owner and operator is the Yanzhou Coal Mine Administration, a division of the Shandong Coal Corporation. These are state owned companies which ultimately fall under the Ministry of Coal in Beijing. The new 3.0 million ton per year Xinglongzhuang mine is located in southern Shandong province in east-central China about mid-way between Beijing and Shanghai. This is an agriculture area, flat terrain, relatively dry climate with temperatures similar to Western Kentucky. During Confucius time (551-479 B.C.) this area was known as the state of Lu. Confucius home town of Qufu is about 20 kilometers to the north-east of the mine site.

Jan 1, 1989

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By P. M. Lin

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands. The method considers column grouting at the specific locations inside the subsidence influence areas including the distressed and stress concentration zones instead of grouting' around and beneath the damaged structures. The later method is commonly used for AML subsidence abatement at the present. By using finite element method the conditions of stress distribution in the strata before and after grouting can be calculated. The design of grout pattern includes the location and number of the grouting holes. Based on the calculation, the proposed method significantly reduces the stress concentration, i.e., the potential of reoccurrence of subsidence can be reduced or eliminated. A comparative analysis including number of grouting holes, grout affected area, stress level, and potential of subsidence reoccurrence will also be presented.

Jan 1, 1990

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997

By John B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals, but any curriculum that does not provide background in such basic subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to utilize geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors and may be faced with legal, social, and political problems in land use, zoning, environmental protection, and reclamation.

Jan 1, 1981

By George W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment® , two new lime substitutes for the treatment of acid mine drainage (Arm), have been compared with lime and Alkament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with EPA regulations. Material utilization and optimum pit are reported.

Jan 1, 1984

By T. Takamori

This paper reviews the present status of coal preparation in Japan concentrating on the process in coal cleaning and waste water treatment. This paper also discusses recent topics on maintenance, automatic control, raw coal management, etc.

Jan 1, 1982

By J. R. Mackie

Reserve Mining Company, the first large-scale taconite pellet producer in the United States, mines it's crude ore at the Peter Mitchell Mire located on the eastern end of the Mesabi Iron Range near Babbitt, MN. The ore is processed at Reserve's beneficiation plant on the north shore of lake Superior at Silver Bay, M. The mine and plant are linked by a 47 mile, double track, railroad which is owned and operated by Reserve. (see Fig 1). At rated capacity, the mine can produce 33 million It/yr of crude ore, 15 million It/yr of waste rock and 1.0 - 1.4 million yd3/yr of glacial till stripping. Haulage of all mined material is accomplished using trucks. Ore is transported by tractor-trailer side dump units which have capacitys ranging from 83 to 110 long tons. Waste rock and glacial till is transported in end dump units of 50 to 120 LT capacity. Loading is accomplished by 11/13 yd3 power shovels and 7/10 yd3 front-end loaders.

Jan 1, 1985

By R. H. Ring

The Automatic Extraction System (AES) was designed and built under a U.S. Department of Energy Contract by the National Mine Service Company in cooperation with the Lee Engineering Division of Consolidation Coal Company. The Pennsylvania State University, Mining Engineering Section, was contracted as an independent auditor of the AES performance. The AES had a rotating cutter drum like a continuous mining machine; but two hydraulically powered roof supports, four roof-bolting drills, a dust scrubber, a ventilation fan and ducting in the roof supports, semi-automatic control, an extensible chain conveyor, and other innovations led to the distinction "extraction system" as opposed to "miner-bolter" or "continuous mining" machine. After design and assembly, the AES was field tested experimentally in an underground coal mine. The in-mine performance audit was preceded by a computer simulation of the potential production for a later comparison with the actual tonnage mined by the AES. This paper describes the results of an in-mine trial and assesses the production potential of the AES.

Jan 1, 1980

By H. R. Hammond

The situation of The Consolidated Mining and Smelting Company of Canada Limited, or Cominco, may be somewhat unique in that the Company is not only a manufacturer of ammonium nitrate, but as a mining company is a major user of its own product. This situation has resulted in highly successful application of ammonium nitrate-oil explosives. Several noteworthy techniques have been developed and others have been improved. Use of this material in the mining industry has led ammonium nitrate producers to adopt the term nitro-carbo-nitrate or INN for ammonium nitrate-oil blends. A small blending plant at Cominco's largest mining property, the Sullivan Mine, at Kimberley, B.C., is producing more than 80% of all the explosive used at the Sullivan, and is supplying two other Cominco mines. Application has required intensive research to determine the best forms of ammonium nitrate for use in small holes drilled for development and long-hole stoping. It has led not only to experiments to determine the best blending oil, but also to development of loading techniques to the point where NCN is being moved through loading tubes over 700 feet. It has required research into mining practices such as hole arrangement and blasting of development cuts. It has resulted in the development of a special product for secondary breaking. All this has been accompanied by the recognition of the importance of insuring safe practices at every stage.

Jan 1, 1963

By Thomas H. Dubaniewicz

(XP) enclosures to enclose electrical ignition sources to prevent propagation of an internal methane-air explosion to a surrounding explosive atmosphere. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a lithium-ion battery thermal runaway test within a modified MSHA-approved XP enclosure to assess thermal runaway containment. Thermal runaway produced jet flames emanating from the cover joint at several locations and distorted the cover joint and bottom plate of the enclosure beyond allowable limits. The test demonstrates that XP enclosures may not provide adequate explosion protection against lithium-ion battery thermal runaway. This paper suggests some approaches to mitigate the hazard.

Feb 1, 2024

By David M. Koogler

If you are contemplating starting a small coal mining operation there is a good possi¬bility that you can not afford it. If you, have already started, you may be on the road to bankruptcy. If you are a small but well established operator you may be trading dollars, or even dissipating your capital, equipment and other assets. A bleak outlook? Yes! Meant to be discouraging? No! Just a reminder that, with todays costs of doing business, high interest rates, rapidly increasing costs and decreasing sales prices, a small businessman/miner had best watch closely or he will be mired in something worse than a soft bottom - namely a cash and credit shortage, and in too many instances In recent times, bankruptcy. We will not dwell on what happens once you are that far gone, though I could cite a good example. But, let us look at what should be done to avoid such a catastrophe.

Jan 1, 1981

By Donald E. Scheck

Blasting practices based on sound engineering principles are well established but the successful application of these practices requires accurate information about the overburden geology and close supervision of the drilling and blasting operations. Good design alone is not sufficient to insure good results, but the process may be difficult to control unless steps are taken to measure the variables and to provide management and the operators with the information they need to establish and maintain control. Satisfactory blasting can be defined as loosening and fragmenting the rock so that it can be handled by the excavating equipment, while at the same time, governmental regulations on air blast and ground vibrations are not violated. Optimum practices achieve these objectives at the lowest combined cost of the drilling and loading operations and the blasting materials. Total system optimization, that is, taking into consideration the effect of fragmentation on the cost of operating and maintaining excavating equipment as well as drilling and blasting costs, probably is not a reasonable goal at the present time.

Jan 1, 1984

By S. J. Cohen

Changes in our energy, national security, and commerce needs have necessitated identification of new sources of minerals, such as rare earths, lithium, copper, silver, aluminum, titanium, and the minerals on the U.S. Geological Survey’s (USGS) list of critical minerals (USGS, 2022). With the need to domestically produce these minerals, more mining will be required within the U.S. Some of these critical minerals deposit with naturally occurring radioactive materials (NORM), therefore, mining these minerals may concentrate NORM to the point that some states may require licensing and radiation protection programs. NORM is not regulated by the Federal government; it is regulated by the individual states. Consequently, overall national state of NORM regulation is chaotic with each individual state either choosing to regulate or not regulate NORM, and, if a state chooses to regulate NORM, then that state develops its own unique regulations. Further complicating the regulatory environment, states utilize a wide variety of strategies for regulating NORM, which sometimes results in inappropriate regulations, inconsistencies with specific radionuclides that are regulated, and inconsistencies with specific NORM types that are regulated. This paper will review the nature of NORM regulations, identify regulatory traps, and provide general guidance for identifying NORM and potentially avoiding regulatory jeopardy. Because of the chaotic nature of NORM regulations nationally, seeking guidance from qualified professionals with relevant expertise is recommended. Also, contacting the appropriate regulatory agency to gain a complete understanding of the NORM regulatory environment is useful for maintaining compliance.

Feb 1, 2023

By R. R. Sacrison

The Barrick Mercur Gold Mine lies in the Oquirrh Mountains of northern Utah. Limestone, sandstone, shale, and chert are the predominant rock types being mined. Recent expansion has encountered rhyolite. Lithology and structural attitudes control most mechanical behavior. Slope steepening, mine planning, and site selection are presented as means by which geological engineering has contributed to the economics of the operation. Geomechanics investments of approximately $700,000 have resulted in cost savings or additional production worth over $16,000,000.

Jan 1, 1990

By K. L. Hanning

Grinding and classification circuits at Climax Molybdenum Co. are described. Since the installation of a direct digital control computer in 1974, a number of control strategies were developed and evaluated. This paper deals in particular with the practical experience and results obtained in direct digital control of a wet grinding circuit consisting of a ball mill, constant speed sump pump, and hydrocyclones. For this circuit throughput is maximized, while maintaining a desired product size. Product size is inferred from measurement of operating variables.

Jan 1, 1977

By O. J. Malacarne

The use of a series of thickeners for-washing of the slime fraction of a leached ore is not uncommon in the uranium industry; however, few ore processing mills have used a thickener circuit for washing leached total ore. The, common, practice is to wash the sand fraction in classifiers and, the slime fraction only in thickeners. At the Uravan mill of Union Carbide Nuclear, Company, a total ore' acid leach is employed to extract uranium values from sandstone ores. These leached ores are then washed at a nominal rate of from 1,000 to 1,300 tons per day in a series of washing thickeners. A typical screen. analysis of the ore being washed in these thickeners, is 25 percent -200 mesh, 3 percent +35 mesh and about, one' percent +l4 mesh., The amount of slimes (-200 mesh) will vary from 20 to 30 percent s the mill receives ore from 150 different mines The washing liquor is acidic, from a pH of about 2 in the first thickener to 0.6 pH in the last thickener and of course ally acid duty equipment must be used. The Uravan mill of Union Carbide Nuclear Company is located in Montrose County, Colorado and is physically located on a canyon wall along the San Miguel river. The thickeners referred to in this, paper are located on top of the mesa above the canyon. For purposes of identification, these thickeners are numbered 1 through 8 from south to north.

Jan 1, 1962