Search Documents

By Liz Diaz, Tacio Ferreira

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill and blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at approximately 380,000 tons a year generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This paper presents how we collected data, reviewed design standards, and found opportunities to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71% on the mine’s highwalls.

Feb 1, 2025

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980

By Mark Van Dyke, Ted Klemetti, Jake Beale, Zoheir Khademian, Joe Wickline

In 2016, a 3.7-ML magnitude event caused by mining activity occurred at a longwall mine in southwestern Virginia which was recorded by the United States Geological Survey (USGS) and felt by local residents. The event was the largest of its kind since a global mine design change by the operator was instituted in 2008 following three large events in 2005, 2006, and 2007 (3.4, 4.3, and 3.4 Moment Magnitude (Mw), respectively). Two of the three pre-2008 events (2005 and 2007) damaged ventilation controls in the mine which fueled a mine fire. In 2016, the mine’s management requested researchers from the National Institute for Occupational Safety and Health (NIOSH) to access geological data and determine what parameters could possibly lead to events of a magnitude of 1.0 ML or greater. Evaluation of 2152 geological data points and modeling revealed three major geological factors in common with the majority of the 181 recorded +1.0 ML events from 2009 through 2016. Three levels of seismic potential were identified as follows:

Aug 4, 2023

By Zohreh Kazemi Motlagh, Virginia T. McLemore

Critical minerals are nonfuel minerals, essential to the U.S. economy and national security, whose supply chain may be disrupted. Mine wastes are potential sources of critical minerals. The goal of this project is to estimate and characterize critical minerals endowment in three mining districts in New Mexico: Black Hawk (Grant County), Hillsboro (Sierra County), and Magdalena (Socorro County), and assess their acid-generating potential. The Black Hawk district is an arsenide five-element vein deposit (Ag, Ni, Co, As, U, Bi, and local minerals like Pb, Cu, Zn, W, and Sn). The Copper Flat mine in Hillsboro district is a copper porphyry deposit. The Kelly mine in Magdalena was first mined at 1878 and are carbonate-hosted Pb-Zn deposits. Mine waste rock piles and tailings are sampled using USGS Beta sampling procedure. Geochemistry results show that Black Hawk district mine wastes samples are elevated in Ag (>200 ppm), Co (290 ppm), Ni (2,130 ppm), and Zn (8,463 ppm). Copper Flat mine tailing is elevated in Bi (111 ppm), Cu (7,453 ppm), and Zn (2,360 ppm). Downhole profile plots in Copper Flat show the positive correlation between Cu, S and Te values. Magdalena samples are elevated in Cu (5,700 ppm), Zn (129,500 ppm), and Pb (58,100 ppm). Determination of acid-generating potential in these areas suggests that Black Hawk district mine wastes are non-acid-forming while high S present in some Copper Flat and Magdalena samples can potentially cause acid mine drainage.

Feb 1, 2025

By Gary English

"Tunnel safety is evolving as science, engineering and technology make advances. Applicable safety codes and standards simply do not cover all the potentials of design, construction and operation. This paper reviews a series of tunnel projects code gaps in Seattle USA that were uncovered during the design and construction of a new highway tunnel, conversion of bus tunnels to combined road and rail tunnels, new rail tunnels using TBM and NATM, conversion of a road tunnel to light rail, and retrofit of an existing road tunnel to add lanes and improve safety systems. The perspectives of the ‘fire code official’ (Authority Having Jurisdiction) on methods to identify and resolve gaps in safety code and standard regulations, while garnering the consensus of the owner, designer, and contractors are presented. Additionally, the emergency responder command perspective on safe tunnel design, tunnel rescue during construction and operational safety is explained TUNNEL SAFETY EVOLUTION The underground has become nearly the only option to provide essential transportation corridors to continue our economic growth in key global areas. Tunnels are not built on a whim. Often significant portion of a regions wealth are invested to meet current, and hopefully future transportation demands. There are more transportation tunnels being built now than at any time in the planets history. The location of these tunnels is often selected for us based upon regional demand. Most commonly under densely populated urban centers and between populations’ centers to bypass geologic conditions like mountains and water bodies. Tunnels are being built in unforgiving soils, between tectonic plates, in extremes environmental conditions and often, under the very heart of the highest density population centers on the planet. All of these locations can bring with it conditions that challenge our common assumptions about safety. These extraordinary locations and soils create risks for both those constructing the tunnel, and in design engineering to meet the ‘minimum’ requirements at the lowest costs. There is lengthy history of above ground safety. Most countries and major local jurisdictions have adopted, or created safety requirements for the construction of above ground buildings. Through decades of use, these safety requirements have evolved, changed and been expanded to cover a wide gamut of actual and potential safety risks. However, the use of the underground for tunnel transportation corridors has grown exponentially with limited attention to safety requirements."

Jan 1, 2016

By J. Wiebmer

Some thoroughbred racehorses are great routers (distance runners), others are sprinters. Some racehorses perform best on turf, others on dirt, and some in mud. To be a winner, you have to choose the right horse for the course. It's no different when looking at an electric cable shovel, a hydraulic shovel/excavator, or a wheel loader. Each loading tool has its own zone of application. To be a winner, you have to choose the right horse for your course.

Jan 1, 1993

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By S. Garcia

The Minera Yanacocha operation presents various operating challenges, due to the complex structure of several heaps interconnected with ponds and gold recovery plants. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters on issues such as water usage and inventory. An integral component of the water/mass balance of the process is a model of each heap that describes the flow and chemical behavior based on the individual characteristics of the heap. A computational fluid dynamic (CFD) software framework is used to model the individual heaps. The structure, calibration and validation of the model are described. Several examples demonstrating application of the process heap model are presented for the La Quinua heap. The effects of loss of solution flow to the heap (i.e., pump failure), increased cyanide levels in applied solutions and higher copper head grades on the process operation and balance are investigated with model simulations and compared to the baseline operating conditions. An example of estimating gold production and inventory based on projected heap loading plans is provided.

Jan 1, 2010

By Harry E. LeGrand

The purpose of this paper is to outline briefly some basic principles of ground-water hydrology that have application in mine hydrology and to suggest that an understanding of these principles can help to forestall problems that are internal as regards mining operations and external as regards damage or harm to surrounding areas. The development of a mine below the water table pleads for accurate values to answers of hydrologic problems. Such internal problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required mining or milling use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by homogeneous rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where rocks are not homogeneous. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground-water occurrence and movement should be helpful to mine operators. Mining operations that extend below the water table disturb the natural hydrologic regimen. Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine, The behavior of the cone of depression, as it tends to deepen and to increase in areal extent when the mine is deepened, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised. The geologic and hydrologic settings of mines range greatly so that a simple standard procedure for dealing with problems

Jan 1, 1972

During the past year a number of significant advances in geostatistics have been published. These were presented at the 13th APCOM Symposium in Clausthal, Germany and at a NATO Advanced Study Institute on Geostatistics in Rome, Italy. Of greatest importance is the work that has been done in establishing methods which correctly predict the cutoff grade-tonnage curves, and the average grade of ore-tonnage curves for deposits in which ore and waste are intermingled. Grade-tonnage curves based on estimates made from widely spaced exploration data have been found to underestimate the grade of ore and overestimate the tonnage present. This problem has been remedied by the calculation of conditional probability distributions for the unknown grade of a block. Another advance has been made in the field of geostatistical estimation for deposits in which a trend is present. Previously a technique known as universal kriging has been used, which involves much subjective judgement as to the trend fitted. A new technique, generalized increments, allows computer estimation of such deposits with much less subjective judgement. Computational efficiency of geostatistical methods has continued to improve to a point where a geostatistical estimate can be obtained for little more than the cost of any other computerized method.

Jan 1, 1976

By Barnettm Ray R.

As a result of the Farmington explosion, the U. S. Bureau of Mines commissioned the National Academy of Engineering to a determine what steps could be taken in a short time frame to significantly reduce fatalities as a result of underground fire and explosion in coal mines. Three areas were named by the Academy as having the greatest potential; survival, communications, and rescue. The Bureau subsequently awarded a $3-5 million contract to the Special Systems Division of Westinghouse Electric Corporation for the development of prototype equipment and procedures. These were recently tested in a simulated emergency situation and will be delivered soon. Contractor recommendations for utilization and for further development effort will be studied and appropriate action taken.

Jan 1, 1971

By Christina Dahnér, Kristina Jonsson, Savka Dineva

The iron-ore underground Kiirunavaara mine (Sweden) has been seismically active since 2008. In 2021 the production is on levels 1079 and 1108 m, at the deepest. The seismic activity has changed in character over time with one step change in 2015 when the number of large (ML>2) seismic events increased, and another one when the mine experienced a seismic event with Mw 4.2 in 2020. In 2017, the mine evaluated Hydraulic Fracturing (HF) as a possible mitigation technique for larger seismic events and a one-hole trial was performed. The trial proved promising, and it was decided to go forward with a large-scale trial covering an entire production area in the mine. The large-scale trial consists of 25 fracturing holes, 50 – 100 m long, running along 500 m out of the ~4500 m long orebody and spanning between production levels 1108 m and 1252 m. The fracturing process continued for a year, resulting in ~38,000 seismic events with −3.3<ML<1.4. The breakdown pressure varied between fractures in the same hole as well as between holes in the same area. Average breakdown pressure per hole was between 12 MPa and 50 MPa. The seismic response to HF in 2021 varied greatly from hole to hole and between fractures in the same hole. The variation in response could be related to the geological conditions and the infrastructure, such as large caving ore passes. In this paper some details about the experiments and broad preliminary analysis of the effect of the HF by using seismic source parameters of the induced seismic events are presented: 1) Distribution of seismic activity, 2) the ‘equivalent’ magnitudes for each hole calculated from the cumulative seismic energy and seismic potency released during the fracturing, compared with the local geological conditions; 3) the predominant failure mechanism of the seismic events caused by HF was defined. A difference in the behaviour between larger and smaller events was noticed, as ML>0 events seem to be compression type failures and ML<0 events seem to be related to slip on pre-existing structures. No seismic events related to creation of a new fracture have been identified yet.

Apr 26, 2022

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

By K. V. Raj

"Air inversion is a meteorological phenomenon generally occurs during winter times. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for health and safety of miners. Mine operations cease if the concentration of NOx or CO exceeds the threshold limit value (TLV) of the pollutants. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Studies of the turbulence parameters suggest that effective ventilation of the pit and removal of pollutants can be accomplished if a large enough mixing length in the open pit can be created. Turbulent mixing by eddies of different length scales under an inversion layer is product of wind shear, thermal gradient and buoyancy. The main result of turbulence is mixing of the atmospheric profile and transport of momentum. Computational fluid dynamics (CFD) Simulation results of a novel mitigation approach using cloud cover will be presented in this paper. INTRODUCTION In extreme climatic conditions, deep open-pit mines tend to trap pollutants at the pit bottom due to air inversions. Keeping open pits adequately ventilated is a considerable challenge for the mining community. Mine operators in cold regions are very familiar with this problem, the severity of which can be judged from Figures 1 and 2. The top portion of the figures show clear sky and snow covered benches. The brown haze, containing various contaminants accumulated over time in the pit under the air inversion, can be seen in the bottom portion of the figures. Several Arctic or subarctic mines have reported air inversions. Even Rio Tinto’s Bingham Canyon pit in Utah has reported local air inversions from time to time [1].Mitigation of pollutants in deep open-pit mines in the Arctic is a challenging task. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for human health. Mine operations cease if the concentration of any one of the pollutants (NOx or CO) exceeds the TLV. Sustained cessation of a mine operation has serious economic consequences. For continued mining operation, the levels of pollutants must be below the TLVs. If no significant synoptic meteorological situation changes during an inversion, a warm air mass sits over the cold air mass within the open pit. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Some of the early approaches in artificially ventilating open pits were attempted in the USSR. Most of the studies by Soviet researchers suggested the use of turbojets and turbo-propeller engines, airscrews, axial pit fans, and meteotrons [2, 3]. However, the majority of these studies were only theoretical in nature, with no evidence of an approach that really worked in practice."

Jan 1, 2017

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying an atomic force microscope (AFM) and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy to study in situ the adsorption of three different collectors — oleic acid, octanohydroxamic acid (HA) and salicylhydroxamic acid (SHA) — on bastnaesite in aqueous solutions. The results show that all three collectors adsorb on bastnaesite. The hydroxamic acid collectors — HA and SHA — adsorb on bastnaesite mainly in the form of insoluble metal hydroxamate. Their specific adsorption mechanism indicates that high selectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By Guillermo V. Borquez

The economics of open pit mine design are dictated by three basic elements: cut-off grade, stripping ratio and slope angle. Although these elements are functions of a number of independent parameters, they are interrelated through their influence on the overall economics. The optimum slope angle is the most uncertain element to determine, because rock mass properties are difficult to obtain. However, for preliminary estimation, the slope angle can be determined from the relationship between the probability of failure and the safety factor. The economics of the slope selected will depend on a profit versus risk judgment. In this paper, the author will present an actual case of application of this postulate.

Jan 1, 1977

By Irwan Halim, Bhoshaga Mitrran Ravi Chandran, Kevin Huynh

Tunnel segmental lining design constitutes a significant iterative process where modeling and numerical analysis are factors in deciding the number of segments, their dimensions, gasket placements, as well as the locations of dowels and bolts. Consequently, these modifications lead to revisions in the final drawing details. However, the current tunnel engineering practices lack systematic solutions that effectively bridge the gap between the iterative design process and efficient visualization of completed drawings due to the time- consuming nature of redrawing. This paper presents a pioneering application of AI-driven solutions including using Autodesk's API, for the Northside Interceptor Tunnel (NSIT) Project. It showcases the automation of drawing design and the real-time visualization of modifications, thereby streamlining the drawing process.

Jun 23, 2024

By Yang Song, Li Shaokang, Wang Zhiqiang, Wang Jinjun, Li Guofeng, Su Meixuan

CaCO3, as a component widely existing in natural minerals, is a common impurity. In recent years, triboelectric separation has been applied to the separation of minerals containing CaCO3. However, the CaCO3’ s tribocharging mechanism is still unclear and the charging effect of CaCO3 is not obvious. In order to study the effect of triboelectric charging of CaCO3 particles under different conditions, according to the single particle frictional collision charge-mass ratio formula derived from the condenser model, an experimental platform for particle tribocharging was built in this paper. Then, the formula of charge-to-mass ratio (Q/m) was derived based on the analysis of the particle force. Particle image velocimetry (PIV) was used to record particle motion trajectories to calculate the Q/m of one particle by this formula. In the experiment, the airflow velocity, tribocharge material, and moving distance of the particles were varied to investigate the variation of the particle charge-mass ratio results. The results show that CaCO3 was negatively charged when tribocharging with mental. The particle’s Q/m is positively correlated with the airspeed. When the metal is triboelectrically charged with the insulator, the metal with a smaller work function leads to the insulator particle with a larger Q/m. As the moving distance of the particles increases beyond 230 mm, the particle charge ratio decreases. The particle charge-mass ratio is consistent with the trend of the charge-mass ratio deduced from the capacitance model.

Jun 3, 2023

By Ernest E. Thurlow

The Geology Division of Northern Pacific Railway Company has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photogeologic interpretation.. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occasional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted.

Jan 1, 1964

By Arthur R. Still, Paul A. Bailly

5.1-PURPOSE, PROCEDURE, METHODS, MANAGEMENT Exploration can be technologically defined, with regard to the discovery of new mineral deposits, as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet and annual output of new extractive operations. The purpose of mineral exploration is the discovery and acquisition of new mineral deposits amenable to economic extractive operations now or in the future. A prime objective of mineral exploration, however, is to find and acquire a maximum number of such mineral deposits at a minimum cost and within a minimum time. Immediately upon the heels of a successful &apos;&apos;exploration" discovery follow activities called, first, development, then operation. Under U.S. Internal Revenue Code regulations (Secs. 1.615.1 and 1.616.1) in effect at the time of this writing, which state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer," exploration in the technological sense may well continue after a mineral property has entered the "development stage" as defined for tax purposes. In many instances continued exploration, after reaching the tax defined "development stage," has disclosed additional reserves which justify a much larger, more efficient and more profitable operation than that which would constitute the minimum feasible. Even after a mine goes into production, continued ore search generally will increase the reserves, either justifying expansions in plant capacity or prolonging the life of the operation, but this work (actually "exploration") is normally considered, for bookkeeping and tax purposes, a part of mine development. Each exploration entity defines its own objectives in terms of acceptable mini- mum rate of return on investment for any deposit found and retained, and in terms of which commodities, and markets, are to be involved. For these reasons, exploration programs, and aims, will vary over a wide range, although all have the common objective of endeavouring to create new profit centers for the future. 5.1.2-EXPLORATION METHODS Exploration has evolved in the past several decades into a highly sophisticated and expensive endeavor in which large corporate entities, or subsidaries, normally are directed and staffed by highly trained exploration specialists. In some instances consultants, with expertise in a given field, are utilized to the benefit of such corporate groups. The "grasshopper" approach to exploration-searching only for outcropping minerals and/or investigating only mineral prospects offered by the discoverers of such outcrops has given us most of the past and present mines in the US., but this method is rapidly approaching the point of diminishing returns in areas that have been thoroughly prospected for currently marketable commodities. With

Jan 1, 1973