Search Documents

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

Global mining company achieves significant productivity gains with three-dimensional (3D) mine models developed with Abaqus finite element analysis software. In a steep change beyond traditional processes, Abaqus finite element analysis (FEA) software from Simulia (the Dassault Systèmes? brand for realistic simulation), is being used to enhance mine design and engineering simulation at a number of major mines around the world. In North and South America, Africa and Australia some of the world?s biggest mining companies are applying FEA technology to evaluate safety and improve design planning, implementation and operations. Beck Arndt Engineering (BAE), a Sydney-based international consultancy, is a pioneer in the commercial development of engineering solutions for the mining industry. The consultancy has worked closely with engineers at Simulia Australia to expand the use of Abaqus FEA simulation software for mining applications. Among the early adoptors of mine-ready FEA technology is the world?s largest miner, BHP Billiton. With BAE?s help, BHP has already applied this technology to evaluate mines in Canada and Australia. At the BHP Billiton Nickel West Perserverance Deeps Project in Western Australia, Abaqus FEA software is now being used to help engineer the safety and productivity of planned deep-mining operations. To achieve this goal in the deep-mining environment significant technological innovation is required. Using measurements of site deformation and seismicity, Abaqus FEA models have been calibrated and, in a single day, used to simulate a full, 3D, inelastic analysis of a mine?s life cycle. In recent years, similar applications at Debswana?s Jwaneng Mine in Botswana, the Newcrest Mining Ridge-way Deeps Project in New South Wales, Australia and Rio Tinto?s Argyle Diamond mine in Western Australia have also established Abaqus FEA analysis as the lead-ing technology for multi scale, simulation-aided mining engineering. Joop Nagtegaal, a pioneer of FEA and a Dassault Systèmes Corporate Fellow, said that Abaqus FEA software is unique in its capabilities to enable mining engineers to investigate design innovations from the drawing board to full production. ?In the design stage, Abaqus models, which include rockmass volumes spanning several kilo-meters around the ore body and down to excavations just a few meters across, are used to compare and optimize engineering options,? Nagtegaal said. ?Then, as the mine goes into production, large volumes of data from the field are incorporated with the analysis models to allow them to be calibrated to a precision not previously available to the mining industry.?

Jan 1, 2009

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this non-hydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1978

By Stig Premfors

Lamco Joint Venture is operating a Dravo Pelletizing machine to produce pellets from the natural slimes of an earthy hematite ore. The grate area of the machine 3.3 x 106 m equal to 350 m2 (3800 sq. ft.) and the installed fan capacity is 8200 HP. The limiting factor for production is normally fan capacity. This means that the processing fans can not pull the additional air (i.e the additional calories or BTUs) through the bed which would be required for increased production. A way to increase production without major modifications is to supply the additional calories needed for increase production by adding coal to the pellet feed. After successful laboratory tests following method of coal addition has been chosen and the following results have been obtained. 1. The ground coal is added to the slurry prior to the filters and the rotary dryer. 2. By adding 0.6% coal, an increase of about 15% in production rate has been obtained. 3. No significant changes of metallurgical properties have been observed (i.e. tumbler index, compressive strength, ferrous iron content, reducibility, Linder degradation and swelling). 4. No unexpected operation problems have been experienced. The pellet discharge temperature increases and is the limit for how much production can be increased by coal addition without making plant modifications.

Jan 1, 1971

By John W. Brauns

18.1-RAILROAD JOHN W. BRAUNS Conventional railroad haulage can be employed at both open-pit or strip and underground mines-in the latter case, largely for transfer of ore from distant openings to processing plants, or processed material to loading points or docks, using standard hopper cars for bottom unloading or gondolas for rotary dumping. The major application, however, is in surface mining for moving ore and/or waste out of the pit to a crushing plant or dump. Consequently, the following will deal largely with this phase of railroad operation, though the conclusions apply equally, for the most part, to other rail-type surface haulage. In surface mining, trains consisting of a locomotive and gondola or side-dump cars suitable for loading by power shovels are used. Gondolas are restricted to hauling ore as a rotary dumper is required. Side-dump cars are more versatile, carrying both ore and waste, but because of their additional dumping mechanism they are likely to be more expensive to maintain.' Also they weigh up to twice a flat-bottom car of the same capacity and. therefore, fewer" cars can be hauled per train. Standard-gage track is most commonly used. Track systems incorporate low-quality temporary track where moves are frequent and permanent high-quality track on main lines. Rail haulage can be used alone, or in combination with other surface haulage methods, thus permitting a selection best adapted to the peculiar requirements of each mining project. 18.1.1---GENERAL APPLICABILITY, CONTROLLING PHYSICAL CONDITIONS For handling rough rock, the shovel-train system is unexcelled.' The ideal applica¬tion is in a large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported over 3 mi. If. in addition, a high production rate is to he maintained, railroad haulage probably will afford a lower cost per ton transported. Grade must he relatively gentle-usually 3% uphill and 4% downhill. The greater the differences in elevation involved, the greater are the track grade space requirements; for example, a 3 c ramp out of a pit only 300 ft deep is almost 2 mi long. Main-line track locations should he selected carefully so that the number of moves during the life of the mining operation can he kept to a minimum. This applies both to the ore haulageway and that for waste. Such moves are not only expensive, but are difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semipermanent trackage. Figs. 18-1 and 18-2 illustrate typical track layouts. The effect of terrain in considering railroad haulage is confined chiefly to the initial cost of the installation. Grade construction in mountainous territory is ap¬preciably more expensive. However, if that expense can be borne, the subsequent maintenance cost of trackage will not he much higher than in areas of low relief.

Jan 1, 1973

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016

By P. M. Pettit

Hydrologic investigations at Gold Quarry began in 1989 and continued through 1991. Hydro-stratigraphic units include Tertiary sedimentary rocks, Paleozoic siltstones and carbonates. These units display complex and variable aquifer parameters as a function of faulting and hydrothermal alteration, creating compartmentalized hydrologic domains. Testing has included step-tests, spinner production logs and constant discharge tests. Two Three-Dimensional Finite Element Models have been developed, one for optimizing the pit dewatering system and the second for predicting regional impacts of dewatering. Aquifer testing and long term pumping have been used to calibrate both Finite Element Models.

Jan 1, 1992

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By D. W. Fuerstenau

The flotation behavior of quartz in the presence of alkyl ammonium acetates as a. function of alkyl chain length has been interpreted in terms of hemi-micelle formation at the solid-liquid interface. The van der Waals cohesive free energy that is responsible for hemi-micelle formation has been found from these results to be 1.02 kT per CH group. This 2 is in excellent agreement with literature values obtained from research on the properties of micelles in bulk systems.

Jan 1, 1964

By S. A. McGhee

ASARCO Incorporated embarked on a modernization and expansion program to improve overall operating efficiencies and to more effectively develop the large mineral reserve at the Ray Complex Open-Pit Mining operation located near Kearny, Arizona. Major elements of this Ray Modernization and Concentrator Expansion Project included engineering and construction of a 54,400 MTPD (60,000 STPD) In-Pit Crusher and Overland Conveying System. and a 24,200 MTPD (30,000 STPD) Copper SAG Concentrator and Tailings Disposal System. Detailed engineering, procurement, and construction management were initiated in November 1989 under contract with Bechtel Corporation. Field construction commenced in May 1990 leading to mechanical completion and start-up during February 1992.

Jan 1, 1993

By P. A. Korpi

The angular spiral lining system reduces energy consumption and grinding media consumption in grate discharge ball mills. This paper discusses the effect of this lining system on mill product size distribution. Performance comparisons of a grinding circuit outfitted with angular spiral liners in the ball mills are made with respect to standard double-wave liner installations. The angular spiral lining system was developed by Waagner-Biro of Austria. The installation of this lining system at Magma Copper Company, San Manuel, Arizona, is the first of its kind in a grate discharge ball mill used for wet grinding.

Jan 1, 1979

By H. M. Castrantas

Caro's (peroxymonosulfuric) acid has been reported to destroy WAD (weakly acid dissociable) CN-but, until recently, the technology has not been demonstrated in other than a laboratory setting. During the last two years, Caro's acid has been shown to successfully detoxify WAD CN-in tailings at two large North American gold mines. Using on-site FMC generators, Caro's acid reduced the WAD CN-from 40-55 ppm to below 20-35 ppm WAD CN-, the target range for the two mines. The detoxification costs using Caro's acid were less than 50% of the treatment cost of using hydrogen peroxide, the previous oxidant of choice. In addition to the considerable savings in CN-detoxification costs, lower WAD CN-values were achieved and the detoxification time with Caro's acid was greatly reduced compared to hydrogen peroxide.

Jan 1, 1995

By Zainab Nasrullah, MontanaFrank Agyemang, Mehran Sadat, Richard LaDouceur

Rare earth elements (REEs) are valuable for various modern technological applications, including metallurgy, machine building, radio electronics, instrument engineering, nuclear engineering, and manufacturing. The extraction and separa-tion of rare earth elements (REEs) from their complex ores is challenging due to their distinct physical and chemical properties, contributing to their market scarcity. At present, REE recovery utilizes traditional pyro- or hydrometallurgi-cal processes. The overall process in the recovery and sepa-ration of individual elements from complex REE systems suffers from high energy demands and the use of many haz-ardous chemicals that negatively impact the environment. With the growing trend toward a circular economy aim-ing to balance sustainability, efficiency, and environmental impacts, this research is focused on using deep eutectic sol-vents (DESs): a combination of a quaternary salt: Choline Chloride and five organic acids: Oxalic Acid, Urea, and Ethylene Glycol, Lactic acid and Glycerol for the selective leaching of REEs from their complex ore which is proven to be green, selective, non-toxic, biodegradable, and cheap. The effects of different DESs and leaching time on the REE leaching efficiency were determined, and the optimum DES media were found to be Oxaline and Lactic Acid at which a leaching efficiency of 25% and 15% was achieved at 80°C respectively for cerium.

Feb 1, 2025

By Robert C. Freas

The Northeastern United States is the most highly urbanized region in North America. It is also an area with a tremendous appetite for stone products. Within this context limestone has truely become an "urban ore". Its uses extend from traditional aggregate markets to lawn and garden, archetectual, chemical, agricultural, industrial, and environmental applications. This paper looks at both the occurance and uses of limestone in the northeast, and briefly examines changing patterns in consumptive use.

Jan 1, 1985

By Wayne L. Johnson

The depth capability of engineering seismographs has been greatly increased by the use of signal enhancement, a technique in which seismic waveforms created by repeated impacts are digitized, stored, and summed. Summation amplifies the signal and partially cancels background noise. This gives a clearer picture of the wave aid makes it possible to determine the travel tune of signals from 'eater depth. Signal enhancement combined with continuous display of waveform, permanent recording of waveform, and precision digital readout of travel time has opened new fields of application in mining and engineering. Recent work has clown that replacement sulfides can be distinguished seismically from country rock at Bistee, Ariz. Work on the Iron Range of Minnesota indication,: that, by using a 300 pound weight as the source, the Biwabik iron Formation can be traced down dip to several hundreds of feet traverses over known areas show that reflections can sometimes be identified. Reflection, if identified preclsely, give a mere accurate estimate of depth and buried topography. Comparison of ( ) and weight drop have given some understanding of low wave amplitude varies win; source candid

Jan 1, 1971

By S. Lu, J. P. Barta, T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate : 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3)Azospirillum had no effect on canopy cover.

Jan 1, 1999

By J. D. Miller

Contact time during bubble/particle collision is calculated by taking into considera¬tion the effect of bubble and particle motion, buoyant force, bubble size, and particle size and specific gravity density for different cases of collision. From this motion analysis approach for the prediction of contact times and from bubble attachment-time measurements,, fundamental aspects of flotation such as flotability, kinetics, and separation can be explained and are discussed with respect to the effects of bubble/particle motion, bubble size, particle size, and attachment time.

Jan 1, 1987