Search Documents

By H. Fayed

Two-phase (water and air) flow in a self-aspirated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). The geometric model is a replica of a 300 m3 cell. A 72-degree sector containing two blades of the ten-blade rotor has been modeled and periodic boundary conditions are applied in the circumferential direction. Simulation of a sector of the machine allows acceptable resolution of the mean flow field using 4x106 grid points. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Unsteady simulations have been performed. In a self-aspirated machine, airflow rate is not known a prior; it is an output from the CFD simulation. Uniform mean bubble diameter of 0.7 mm has been specified as an input for the simulation. Air flow rate and power consumption have been monitored with time, and results indicate a stable operation. Air volume fraction contours and velocity field in different regions of the machine are presented and discussed.

Feb 27, 2013

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

By A. C. Barlow

The use of deep wells for waste disposal is not a new technique. The production phase of the oil industry has been using this method to dispose of unwanted oil field brine since the 1930's The adoption of this method by other branches of industry, however, to dispose of manufactured wastes is a relatively new development, but one which is finding increased use (2). Deep well waste disposal is not an ordinary technique even though it is finding relatively wide application. In fact, just the opposite is true; it is still a rather extraordinary measure. It is not now, nor is it ever likely to be a disposal method which can be assured of success before it is tried.

Jan 1, 1964

By Madan M. Singh

A new mining project can raise questions about what effect it will have on the community after it closes. Historically, little was done by communities to plan for and accommodate the changes in the economic infrastructure when a mine project is finished either after the ore runs out or if market conditions deteriorate and make it unprofitable. Projects that were underfunded were generally unable to withstand periodic market downturns. However, data in a recent study conducted by the Seidman Research Institute leads to the conclusion that, even when a mining project is terminated, there can be (and, in the specific case studied, is) a residual beneficial economic effect in the community, which lasts for a long period of time.

Jan 1, 2010

By E. K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. While providing a useful tool for the investigation of mine planning problems, the availability of graphic output was limited or non-existent. Computer graphics is a natural extension of mine simulation methods and provides a more dramatic level of understanding and interface with an engineer. With today's high cost of venture development, the need for an easy to use but complete systems model which includes the major elements of mine planning with an interactive graphics interface has never been more apparent. In this paper, the underlying philosophy of design of an interactive interface to a complete surface mining simulation model is described. The basic structures of the surface mining system and the simulation model are discussed. The methods and algorithms used to implement the various subsystems are presented. Practical considerations of the design of displays and user interaction are illustrated, especially as they apply to the application of the package by a mining engineer. A simple example is provided to demonstrate the concepts embodied in the model and to show how a simulation is built from mine data.

Jan 1, 1984

By Joel K. Waterland

The Homestake Mining Company at Lead, South Dakota is one of the few remaining gold properties still in operation, in this country. The mine is relatively deep, with a bottom production level of 4250 feet, and a bottom development of 6200 feet. 4, 800 tons of ore are produced daily from three rather large, but inconsistent ore bodies; the dip of which is easterly at about 72 degrees, and the plunge to the south is about 30 degrees. The ore is, for the most part, a chlorite schist with large veins of secondary quartz and cummingtonite schist The ore is not continuous in any direction, but is localized at the ridges of the very intricate system of anti clinal folds. This property has been in active production since its establishment in 1876, except for a period during World War II. The incentive, or contract pay system, has been a gradual process that has been developed by the trial-and-error method down through the years. In looking over the old records, hand-shoveling was paid on an incentive basis as far back as 1916. Since this time, the contract system has grown until it now includes almost all types of underground work - except haulage and maintenance work

Jan 1, 1960

By Ralph C. Kirby

The U.S. produces about 34 percent of the world's aluminum yet must import 90 percent of the raw materials needed. There are abundant resources of aluminum-bearing minerals such as clay, anorthosite, alunite, shale, and dawsonite, but none of the numerous processes proposed for recovering alumina from them has yet proved economically competitive with the Bayer process using imported bauxite. To help develop an economically viable process for utilizing these resources, the Bureau of Mines is testing on a common basis several proudsing processing techniques. New improvements and approaches developed by industry and the Government are being evaluated on a mall scale to obtain enough information on which to form a judgment regarding the best processes for commercial adoption. A continuous miniplant having a feed rate of about 70 pounds per hour is being operated now to investigate the nitric acid process for recovering alumina from clay. Parts of this plant will be used subsequently for work on other processes for recovering alumina from clay, anorthosite, alunite, and dawsonite. Initial results of the operation and plans for the overall project will be discussed.

Jan 1, 1974

By Jr. Watts

The American Mining Congress and the U.S. Bureau of Mines have formed a collaborative research team to develop, implement, and evaluate a comprehensive control strategy to reduce diesel particulate matter concentrations without degrading other air quality parameters at an underground noncoal mine. Other participating organizations include Caterpillar, Inc., the Mine Safety and Health Administration, and the University of Minnesota. After extensive baseline information and air quality data are collected, available control strategies to reduce diesel particulate matter exposures will be implemented, individually or in combination, and evaluated. This paper discusses the objectives and protocol of the collaborative effort to evaluate diesel particulate control technology.

Jan 1, 1995

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercapto silanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1990

By A. Iannacchione

Most legacy drift mines entered the coal reserve from outcrop and developed up-dip. The Surface Mining Control and Reclamation Act of 1977 changed this way of mining, requiring all new mines with acid- or iron-producing coal seams to be designed so as to prevent gravity water discharges from the mine. This Act requires engineered barriers to contain the mine pool. In many cases, mine layout designs focus primarily on the size and hydraulic performance of the un-mined coal barrier between the up-dip mine pool and areas where down-dip surface discharge is possible. In other cases, designs focus on preventing discharges from barriers contained within the strata surrounding the mined coalbed. This paper focuses on a detailed analysis of the factors responsible for preventing mine pool discharges to surface waters. Important factors include: mine layouts, mining methods, hydraulic head and conductivity, and geology. While the exact causes for the successes and failures could not always be determined, reasonable mechanisms are presented.

Feb 23, 2014

By Ibezim J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous content and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, Alabama and FMC Corporation in Pocatello, Idaho were investigated using physical separation techniques to recover the elemental phosphorous in the sludge and to render the residual material non-hazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69 -90% P4 with a recovery in the range of 60 -87%. Dispersed air oxidation of the fines and tailing products was effective in removal of an additional 10 -15% of the P4 in the sludge.

Jan 1, 1991

By Mustafa Kumral, Yuksel Asli Sari

Underground mining operations are sensitive to price fluctuations because they usually perform with a narrow profit margin compared to open-pit mining. Furthermore, the economic evaluations regarding operation are based on estimated or simulated grades rather than actual values. These bring a high degree of uncertainty to the viability of an operation. Hence, mine planning that accounts for uncertainty is crucial for underground mining operations. As an underground mining technique, sublevel stoping has geotechnical, curing time, seismicity, cost minimization, and production requirements. A new mixedinteger linear program is proposed that considers the uncertainty associated with net present value using chance-constrained programming. The net present value (NPV) maximization objective is transformed into a multi-objective maximization problem where one objective is to maximize the mean NPV, and the other objective is to maximize the negative standard deviation multiplied by a scalar called risk or reliability level. The balance between the two objectives was maintained by this scalar and was selected based on the reliability level of the project. A case study was conducted with varying reliability levels, and sequences were generated. It was shown that the expected net present value increased at higher reliability levels, and the overall value of the objective function decreased as the reliability level increased. In other words, the variance component penalized the value of the objective function. Moreover, it was observed from the case study that at lower reliability levels, stope grade order bears similarity to the extraction order.

Aug 4, 2023

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

By A. Podlesny, E. N. Rubinstein, J. J. Sammarco, B. Demich

Roof bolting typically follows the extraction of a commodity to help keep the roof from collapsing. During 2004 to 2013, roof bolter operators had the highest number of machinery-related injuries, accounting for 64.7 percent, at underground coal mines. This paper analyzes U.S. roof bolter fatal and nonfatal lost-time injury data at underground work locations for all commodities from 2004 through 2013 and determines risk indices for six roof bolting tasks. For fatal and nonfatal incidences combined, the roof bolting tasks in order of the highest to lowest risk index were bolting, handling of materials, setting the temporary roof support (TRS), drilling, tramming, and traversing. For fatalities, the roof bolting tasks in order of the highest to lowest risk index were handling of materials, setting the TRS, bolting, drilling, traversing, and tramming. Age was found to be a significant factor. Severity of injury, indicated by days lost, was found to increase with increasing age as well as with increasing experience, largely due to the confounding of age and experience. The operation of the roof bolting machine used in underground mining should be a research priority given the high frequency and severity of incidents. The results also suggest that temporal factors may exist, so additional research is warranted to better understand these factors and potentially develop interventions. This research provides a datadriven foundation from which future research can be conducted for safety interventions to reduce the frequency and severity of incidences involving the roof bolter activities of bolting, handling of materials, and setting the TRS.

Jan 1, 2016

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By Carl Erickson

The term shortwall mining is somewhat of a mis¬nomer. It may infer a longwall mining system, but of much shorter face length. Actually, continuous pillar mining is a more descriptive term. Coal is mined using a continuous miner as would be done in pillar extrac¬tion, but with the addition of roof supports to control the caving. Face length on such a system typically is 46 to 61 m (150 to 200 ft). The coal is cut in front of the roof supports in the same direction as with a long¬wall shearing machine or plow, but it is mined with a continuous miner and shuttle cars of the same type as used in continuous mining. ROOF SUPPORTS Roof supports for shortwall mining must be con¬siderably larger than those used for longwall mining because of the additional roof to be supported by the wider 2.6- to 3.4-m (81/2- to 11-ft) cut of the continuous miner. Capacities of shortwall chocks in current use vary from about 454 to 726 t (500 to 800 st). The higher capacity as compared to longwall roof supports is needed primarily because of (1) the greater support length, hence more roof weight, and (2) the presence of draw slate in the eastern coal seams, where shortwall is being used. The most popular shortwall support currently used is the four-leg 590 t (650 st) model. This support is shown in Fig. 1. The price of this support is approxi¬mately $25,000 each. As shown in Fig. 1, the shortwall chock incorporates an unusually long forward bar that has an additional hydraulically operated extension bar to provide face support for the wide miner cut. METHOD OF OPERATION Mining Sequence In shortwall mining, two or three (depending upon the chock design) move up cycles of the chock are needed because of the miner cut width. Fig. 2 depicts the five steps required to complete the move of chock and spill plate using a miner that takes a 3.3-m (10-ft,

Jan 1, 1982

By Edward A. Nowatzki

The purpose of this paper is to present an example of the application of a theoretically derived mathematical model for track-soil interaction to the evaluation of the mobility of large-scale mining equipment used in open pit operations. The model described by Karafiath and Nowatzki (1978) and presented in detail by Karafiath (1978) was used to predict the performance characteristics of four different bucket wheel excavators (BWEs) on rwo types of copper mill tailings at various moisture conditions. The BWEs considered In the analyses are two-and three-tracked continuous excavators. Most have boom-mounted rotating buckets and swinging side- or rear-discharge conveyors. The analyses were performed at the request of Dames and Moore for the Kennecott Corporation's proposed remining of selected tailings deposits at the McGill, Nevada, concentrator. The objectives of the analyses were to determine whether BWEs would have sufficient mobility In the tailings deposit to achieve satisfactory production rates, and TO compare the predicted performance of the various BWEs evaluated. Good qualitative agreement was obtained between the results of the theoretical analyses performed for the McGil1 operation and the actual performance of BWEs in two South African gold mine tailings impoundments.

Jan 1, 1980

By Adrian C. Dorenfeld

Concentradora "Dana Aida" (100 t/d capacity) was built in 1971-1972 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals from two veins. The veins, Don Felipe and aria are about 150 m apart, but are distinctly different mineralogically. The deposit is near San Juan de Guadalupe, Durango. Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuila. Sampling, ore testing, flowsheet design, plant design, drawings purchasing, financing, etc. was planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1979

By E. DeLilia

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to in-crease productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: ? Prudent engineering. ? Proper planning. ? Realistic feasibility studies. ? Effective specification. ? Thorough training of the mine personnel.

Jan 1, 1995

By M. C. Manderson

Phosphate rock is a naturally occurring mineral which, in upgraded form, is important to both agriculture and industry. Phosphate rock normally must be upgraded before it can be assimilated and used. Most of this upgrading is now carried out by chemical means, largely through the reaction of a strong inorganic acid (primarily sulfuric acid) with the phosphate rock to remove major impurities and to produce soluble phosphate. A less important but yet still commercially significant conversion method involves the thermal reduction of phosphate rock at high temperature in an electric furnace to produce elemental phosphorus. The elemental phosphorus is then converted to usable end products. This conversion route is a more costly method than the chemical route, but it has the advantage of being able to produce chemically pure phosphorus derivatives. On the other hand, the use of phosphate rock for agricultural application-primarily for use as a plant nutrient ingredient for fertilizer -does not require the same level of purity. As a consequence, the chemical method of phosphate rock upgrading is the predominant technique for producing phosphatic fertilizers.

Jan 1, 1977