Search Documents

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The integrated grouting method, as developed in the USSR, can be applied to multi-purpose operations that in¬clude the construction of shafts, drifts, and tunnels. In the USSR it has been used extensively for primary and final grouting of underground excavations in mining engineering and civil engineering projects. It has been applied in projects where the primary objective was waste contain¬ment. It has also been used to control subsidence beneath buildings located over mined out openings and to eliminate the flow of ground water beneath and around dams. This chapter considers several industrial applications in the form of case histories. The word integrated means that grouting activities were integrated with other activities. 9.1 CASE HISTORIES OF GROUTING FRACTURED ROCK WHEN SINKING VERTICAL SHAFTS The integrated grouting method has been applied most widely in the sinking of vertical shafts in fractured, satu¬rated rock. As explained previously herein, grouting oper¬ations preferably are carried out from the ground surface where they are integrated into the schedule of the setting up of the shaft excavation and construction equipment. Such integration reduces significantly the length of time required for preparation of shaft construction and the time required to sink the shaft. The increased efficiency is achieved by the elimination of cementing operations from the working face upon the penetration of each aquifer. Concomitantly, labor and energy consumption during shaft sinking are minimized because the more complicated and labor-intensive work is carried out at the surface section. Table 9.1 presents the essential parameters for the pri¬mary grouting of saturated fractured rock carried out by the integrated method when sinking vertical shafts. 9.1.1 NAGOL'CHANSK MINE NO. 1-2, VENTILATION SHAFT NO. 1 The integrated method of grouting saturated fractured rock through holes drilled from the surface was employed for the first time during the sinking of vertical shaft No. 1 at the Nagol'chansk mine No. 1-2 in the Don Basin. The shaft had an inside diameter of 6 m. The grouting operations commenced by using cement grout with a density of 1.7 to 1.8 g/cm3. Clay-based grout with cement and other addi¬tives was used only for grouting the aquifers where cement grout proved to be ineffective. By the time of the grouting of ventilation shaft No. 1, hydrodynamic analytical methods were well in hand and a preliminary method for designing isolation curtains had been developed. A method for designing and drilling ori¬ented directional drillholes whose natural curvature re¬flected the characteristics of the fracturing had been devel¬oped. The majority of the necessary equipment had been developed. Clay-based grouts were considered ready for the first industrial application. The hydrogeologic environment at the Nagol'chansk mine No. 1-2 contained many prolific aquifers. According to monitored drillhole data, the total expected inflow into ventilation shaft No. 1 without grouting was 425 m3/hr. This large ground water inflow rate was supported by in¬formation obtained during the sinking of the main shaft and from the auxiliary shaft of the "Nagol'chansk" mine No. 1-2. The construction contractor at the site began sinking ventilation shaft No. 1 to a depth of 217 m by cement grouting from the working face of the shaft. As a result of the cement grouting operations, the inflow of water was reduced from 105.4 to 40 m3/hr over this 217 m interval. However the residual inflow rate caused the shaft to become functional at the depth of 217 m. At this point all grouting operations were transferred to SPETSTAMPONAZHGEOLOGIA (STG) in an effort to improve the operation. In order to carry out preliminary grouting from the sur¬face, seven drillholes were installed and designed for re¬ceiving grout. Drilling was implemented by the ZIF-1200A rig to the design depth of the shaft. The geometry of the principal fracture system that would be encountered by the shaft was estimated while breaking ground using informa¬tion from other shafts. The drillholes were arranged so that they cut through the aquifers uniformly around the shaft. Some preference was given to intercepting the aquifers that were located along the rock dip above the shaft bottom because it was established that the ground water in the aqui¬fers flowed downward along the dip into the cone of de¬pression of the shaft. Investigations in the drillholes using the DAU-3M flowmeter described in Chapter 3 showed that all of the nine aquifers were penetrated by the time a depth of 690 m had been reached. The flowmetric information showed that aquifer numbers [1 and 2], [4, 5, and 6], and [7 and 8] had practically identical hydrogeologic characteristics; so it was decided to connect them into combined stopes and inject the grout using five stopes instead of nine. Table 9.2 shows the results of the grout injection into the aquifers. The volume of grout pumped into the separate intervals through single holes varied from 204 to 15 m3. The trend of grout consumption showed a reduction of grout consump

Jan 1, 1993

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors' records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By B. Seegmiller, W. A. Hustrulid, O. Stephansson

Introduction The concept of in-the-wall haulage was formally introduced to the mining community in the early 1970s. The basic concept is simple. Rather than the traditional in-the-pit haulage/access ramp, single or twin ramps driven in the pit wall are used with crosscut connections on the working levels. The in-the-wall pit haulage system could be considered as part of the opening of a new mine, a way of completing to final depth an existing pit, or part of the transition from open-pit to underground mining with the ramp remaining as part of the access. This paper is intended to acquaint the reader, particularly mine planning engineers, with some of the possibilities presented by the concept. Nordstrom (1983) said, "In many countries, mining engineers are either open-pit or underground specialists and, hence, often don't consider the possibilities for combining the best aspects of each into a hybrid mining system." This is believed to be true. There are few "hybrid mines" employing, for example, open-pit methods with underground haulage systems. One reason is the variance with the experience of the mining company and the engineers involved. However, with today's low metal prices, innovative and unconventional thinking may be just what a property requires to remain in production. All the possible situations where an in-the-wall ramp might be considered cannot be presented here. Rather, a few examples will be discussed for illustration purposes. Potential savings in stripping costs A major cost in open-pit mining is associated with the removal of overburden and waste rock. Although much of this stripping cannot be avoided, the volume (V) associated with the presence of an in-pit haul road can be quite large, V 100 (pit depth) a (road width) 2 x road grade (%) As an example, consider a vertical ore body 400 m (1312 ft) long, 60 m (197 ft) thick, extending to a depth of 160 m (525 ft). Cross sections are shown in Fig. 1. Other data are: ore tonnage = 11 Mt (12 million st), ore density = 2.9 t/m3 (0.09 st per cu ft), waste rock density = 2.7 t/m3 (0.08 st per cu ft), road width = 20 m (66 ft), road gradient = 10%, and level interval = 10 m (33 ft). The evaluation has been made assuming that the pit slope (0) is constant around the pit except on the side with the haul road. On this side, the slope is decreased to allow for the road. Slope angles of 30° to 60° have been selected to indicate the dependence of stripping volume (V) on slope angle. The stripping at the ends have been calculated assuming representation by cones. The volume associated with the haul road is 2.6 Mm3 (92.8 million cu ft). A comparison of the strip volumes involved is shown in Table 1. As can be seen, the percent savings in strip volume varies from about 4% to 17% and depends greatly on the slope angle. It is perhaps more interesting to examine the savings in stripping costs that could then be used to cover the cost of the access ramp and the crosscuts for stripping costs of $3/m3 ($0.08 per cu ft). The cost with the road volume is 2.6 million x 3 = $7.8 million.

Jan 1, 1988

By James C. Barker

Alaska?s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ?green? energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010). The REE, accompanied by other high field strength metals (such as Nb, Zr, Ti, Th, W), are associated with alkaline complexes of the Hogatza Belt in northwest Alaska; peraluminous tin-granites of the Ruby batholith in central Alaska and the Porcupine plateau in the northeast; and peralkaline intrusive complexes in the southwest Alaska Range west of Anchorage, and on Prince of Wales Island in southeastern Alaska. Limited evidence suggests that the heavy REE are associated with deposits that became more highly evolved by late hydrothermal processes.

Jan 1, 2012

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By Yi Yang, Xiuzhu Su, Wei Sung Ng, Shuiping Zhong, Miao Chen

With over 260 tons of gold reserves, the Shuiyindong gold mine is one of the largest Carlin-type gold deposits in China. A particular challenge in the processing of the ore is the presence of carbonaceous compounds, which can cause substantial losses in recoveries via the preg-robbing and adsorption of gold. To investigate the structural properties of the native carbon and to compare between different characterization techniques for such compounds, pre- and post-flotation mineral samples containing 0.9–4.8% non-carbonate carbon from the Shuiyindong mine have been examined via mineralogical and thermogravimetric approaches, as well as spectroscopic techniques, including X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine edge structure spectroscopy (NEXAFS), solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, Raman spectroscopy and preg-robbing measurements. NEXAFS and DRIFT yielded the most reliable results, indicating that 60–75% of the organic carbon in all samples consist of aliphatic alkenes with substantial unsaturated content, highly similar to activated carbon, with the remainder being graphitic and humic. Speciation by XPS was sub-optimal due to spectral overlaps between graphitic and aliphatic carbon, and between carboxylic and carbonate functionalities, while NMR spectroscopy could not provide reliable speciation of the carbon groups. The preg-robbing strength was strongly correlated to the aliphatic content and structural disorder in the carbon, while no such relationship was found with the graphitic and humic content.

Nov 29, 2021

By M. S. Celik, H. Du, J. D. Miller, F. Cheng, O. Ozdemir

"In this paper, recent progress with respect to the flotation chemistry of soluble salt minerals is reviewed, and some of the more relevant issues including the hydration states of ions, the interfacial phenomena of salt surfaces and the flotation behavior of selected soluble salts are discussed. Due to the high solubility, the flotation of most soluble salts has to be carried out in their saturated brines. Anecdotal evidence has suggested that the hydration states of the ions have significant influence on the physicochemical properties of the solutions, the surface charge and wetting characteristics of the minerals, the collector adsorption states and, further, the flotation behavior of the soluble salts. In this regard, reviewing past research findings, efforts are made to establish a correlation between the ion hydration states with the flotation behavior of the soluble salts. Further, advances in understanding the significance of colloid adsorption involved in the soluble salt flotation process are addressed, and future research efforts to understand the soluble salt flotation chemistry are suggested.IntroductionSoluble salt minerals are essential raw materials for the production of a variety of commodities, fertilizers, potassium hydroxide, soda ash, magnesium compounds and other chemicals. These soluble mineral resources can be processed using flotation technology and, currently, more than 80% percent of the world’s potash is produced by the selective flotation of KCl crystals (sylvite) from other salt crystals, predominately NaCl (halite) and other more complex salts (Searls, 1990). Despite the successful application of flotation technology in the potash industry, the mechanisms for collector adsorption on soluble salts have not yet been fully understood and, therefore, have been of considerable interest to flotation researchers for many decades."

Jan 1, 2015

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By Furuyama Takashi, Mori Sukeyuki, Hara Tsuyoshi, Fukushima Yujin

In mineral processing practice, flocculation is largely established as an engineering technique of waste water treatment and the study of parameters increasing the settling velocity of particles is still of great importance to improve the process. Further investigations were made using quartz (Q89) and fluorite samples (F91) which included 58.8% and 65.8% of -2.3 µm particles respectively. In all the experiments the flocculation phenomena were observed varying the pH value of the aqueous suspension. In contrast to quartz particles (Q89) which did not flocculate for all pH values, it was, noticed that fluorite particles (F91) flocculated in the alkaline range of pH over 11. With an aqueous suspension containing equal quantities of Q89 and F91, a hetero-flocculation of particles was observed at a range of pH below 10. In this case, the maximum floc size of the hetero-flocculation was 37.0-26.2 µm This size was about three times larger than when quartz (Q84) and fluorite particles (F85) were used with 32.4% and 40.4% of -2.31 µm particles respectively. Besides, in the experiments using Q89 and F91, the maximum size of hetero-flocculated single particles was found to be 6.54 µm instead of 3.27 µm as obtained with Q84 and F85.

Jan 1, 1995

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By Frederic Souche, Andrew R. Klaetsch, Brian Hann, Nick Goodenow

This paper describes support of excavation (SOE) design and construction for three large diameter shafts excavated through glacial soil and controlled blasting in complex sedimentary rock formations. SOE in soil consists of unreinforced secant pile rings designed to resist lateral pressure in circumferential compression, eliminating costly steel core beam reinforcing. Controlled blasting at the shafts, adits, and tunnels in densely populated neighborhoods requires managing risks to the public, buildings, and utilities. Controlled blasting approaches limited adverse impacts to receptors nearby while achieving adequate production and fragmentation. A site-specific observational approach was used to adjust blasting parameters, limiting the impact on local stakeholders while maintaining daily progress and managing overbreak.

Jun 13, 2023

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By William Gleason

"In a time that seems to be dominated with nothing but bad news coming from the mining industry, there is a success story that has been quietly happening in Southwestern Wyoming for more than 60 years, and it is one that is likely to continue for many decades to come.Beneath the wind swept high desert plains of Sweetwater County, WY, about 32 km (20 miles) west of Green River, lies the Green River Basin where five companies, including Tata Chemicals North America (TCNA), are mining the world’s largest known deposit of trona and, in turn, are collectively producing 15.3 Mt/a (17 million stpy) of soda ash.“We have a long-term growth story that has been, and will continue to be a steady earner for many years to come,” said J. Martin Keighley, managing director of TCNA who has been in charge of the mine, formerly known as General Chemical Industrial Products Inc., for Tata Chemicals for about three years.According to the U.S. Bureau of Land Management (BLM), Keighley is safe with his prediction of future success. The BLM estimates that there are enough reserves in the Green River Basin to last another 2,000 years. Currently, four trona beds in the Green River Basin are being mined and in all, there are 25 major trona beds that occur within the Wilkins Peak Member of the Upper Eocene Age Green River Formation. The trona deposit as a whole covers about 2,500 km2 (1,000 sq miles) within the Green River Basin.And imagine, this economic mainstay in the region was discovered accidently.Prior to 1948, soda ash, the salable commodity that comes from trona and is used in a host of products including glass and detergent, was produced synthetically. In 1938, an oil and gas exploration team working in the Green River Basin came away with a find that would change the soda ash industry and the physical and employment landscape of southwestern Wyoming forever. Within 10 years, the communities of Green River and Rock Springs, which were built largely on the back of coal mining and railroads, had another commodity beneath their feet."

Jul 1, 2016

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By Dejan Petrović, Pavle Stojković, Jelena Ivaz, Saša Stojadinović

In spite of the fact that flyrock phenomenon represents the real threat for personnel and machinery, it still remains insufficiently investigated. There are efforts, in the mining community, to explain the causes of flyrock, but the models capable to accurately predict flyrock occurrence and define the flyrock distance still do not exist. This article is an attempt to establish such a predictive model. The model utilized the adaptive nature of artificial neural networks and combined it with the accuracy of numerical modeling of physical phenomena. Necessary data were collected by high-speed camera recordings of actual blasts at three different surface mines and processed for further use for artificial network training. The result was a neuro-numerical couple which was capable to predict flyrock occurrence, estimate the launch velocity of flyrock fragments, and calculate the maximum distance of flyrock fragments. The safe distance was then calculated by multiplying the flyrock distance with a factor of safety. The article explains the procedure for data acquisition and processing, artificial network construction, training, and validation. It also explains the principles of flyrock distance calculation and, finally, provides a definition of factor of safety and safe distance. The results showed that the prediction was satisfactorily accurate and reliable.

Oct 22, 2021