Search Documents

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By William G. Pariseau

Few departments of mining, metallurgical or petroleum engineering in the United States have critical mass. Cost per student credit hour (SCH) in departments across the country are usually the highest among engineering departments, which are the highest on campus. Almost all departments are operating at fixed costs and enrollments could easily double without incurring much additional cost. However, the cost per SCH would remain unacceptably high and the probability of doubling enrollment is nil. Declining enrollment is a more likely future. The pressure to reduce SCH from university administration is unrelenting. And it has the potential for doing serious damage to program quality when standards and requirements are lowered in attempts to maintain enrollments and increase retention.

Jan 1, 2002

By Lee R. Kump, Sarma V. Pisupati, Peter L. Rozelle, Alan R. Larson, Timothy S. White, Nicholas A. Crescenzo, Maureen D. Feineman

The Mercer Clay bed in central Pennsylvania has produced feedstocks for the refractory industry in the USA and has also been investigated as a source of alumina and lithium. Developments in global markets for these commodities, as well as rare earth elements, have led to their classification as critical minerals in the USA, in turn renewing production opportunities for the Mercer Clay resource. The work reported here includes a review of the clay types and minerals involved, as well as past mineral processing and extractive metallurgy test work, and reports new research results from renewed investigation of the deposit as a polymetallic resource. This renewed work has found lithium contents that exceed 1,000 ppm, lying directly below the overlying Mercer coal, where the alumina content ranged from 32 to 34 wt%. Total rare earth concentrations were somewhat lower than have been found elsewhere in the region, and the highest contents were also found to be stratigraphically close to the coal. Further work is required to establish the mineral hosts for lithium and rare earths and to define the extent of enriched alumina, lithium, and rare earth concentrations.

Jul 22, 2021

By Robert A. Jankowski, J. Drew Potts

The Bureau has identified several ventilation techniques and a water spray application for reducing auger mining dust levels. The dust control methods all work by improving air quantity or flow patterns at the face. Section airflow is maximized by reducing air leakage between entries. Sealing stoppings with brushed- on mortar, containing fiberglass additives, reduces leakage. Heading airflow is maximized by properly installing the brattice curtain and keeping the area between the curtain and rib free from obstructions. The brattice curtains should be hung at least 1.7 m (5.5 ft) from the ribs in 7.9 m (26 ft) wide entries and kept less than 4.6 m (15 ft) from the face. A tight curtain seal is created by using the mine air pressure to force the curtain against the timbers, roof and floor of the mine. Using both a blowing curtain and an exhausting curtain will isolate some face workers from dusty air. The Bureau designed, auger clearer spray system, can be used to force heading air across the active face. Laboratory tests indicate that the auger clearer spray system can increase face velocities by more than 0.5 m/sec (100 ft/min), while using less than 0.13 l/sec (2.0 gal/min) of water.

Jan 1, 1989

By D. D. Schlepp

There is a continuing debate about the influence of circulating load and classifier efficiency on the capacity of the circuit. Specifically, the effects of preferential classification, bypassed fines, and the sharpness of classification will be examined. Horizontal cyclones have also proven to be very successful in a number of operations but their impact on the circuit capacity has not been clearly defined.

Jan 1, 1990

By K. Huttu, A. van Wageningen

"The Kittila underground mine is extracting one of the largest known gold deposits in Europe and has an estimated mine life through 2034. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. The ore at the Kittila mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulphide minerals – arsenopyrite and arsenic-rich pyrite. The orebody consists of a complex pinch-and-swell structure including up to 100 different gold mineralization lenses. Fluctuating gold prices and other economic considerations increase the need to maintain and update the mining plans more frequently. Over 3,000 stopes need to be designed and optimized once a year for the LOM-plan and more frequent updates are needed for mid- and short term plans as well as production studies. As a large part of ore body is very sensitive to cost and gold price changes, stope optimization is crucial to find the best possible production scenario for every moment. Kittilä has gone through several methods for stope design and optimization. Most recently the Deswik Stope Optimizer (Deswik.SO) has been successfully used. Dewsik.SO has helped Kittilä to design and optimize stopes in a timely and cost efficient manner. Together with the Deswik suite of planning tools, reliable and auditable plans are created. This paper describes the methods used for stope design and optimization at Kittilä. THE KITTILÄ MINE The Kittila underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittila achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two open pits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small open pits will mine any remaining near-surface reserves in the future. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. With a mine life estimated through 2034, Kittila is Agnico’s longest-life mine. The mine’s proven and probable reserves contain 4.7 million ounces (32 million tonnes at 4.6 g/t gold). Ore has been mined from underground since 2010. The original 3,000-tonne-per-day operation underwent an expansion project to increase the throughput capacity of the mill by 1,000 tonnes/day, starting by the end of 2014. The region around the Kittila mine is underlain by mafic volcanic and sedimentary rocks of the Kittila Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle's Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between iron-rich and magnesium-rich rocks lies a 100- to 200-metre-thick structural zone known as the “Suurikuusikko Trend”. This trend hosts the Kittila deposit, where multiple mineralized zones have been traced over a strike length of more than 25 kilometres."

Jan 1, 2015

By B. Cavender

Mining managers trying to rapidly reduce production costs tend to implement a traditional set of top-down managerial practices: layoffs of employees, renegotiation of supplier contracts, cancellation of employee training, restrictions on travel, reductions in office supplies, and so forth. While these practices do reduce costs, the benefit is often limited in both magnitude and duration, and the workforce is usually left demoralized. Successful cost-cutters take a different approach. They make the continuous reduction of costs a priority for all members of the organization, whether managers or workers. The culture of these firms emphasizes the commitment, voluntarily given, of individuals and work groups to this goal. Cost cutting practices often reject all of the traditional methods mentioned above, but are far more numerous, innovative, and successful. This culture of cost reduction is the result of a set of leadership competencies that establish direction for the organization, align the organization’s various constituencies with this direction, and motivate and inspire the organization. Dramatic cost reduction then becomes a routine task rather than a heroic achievement.

Jan 1, 2000

By George M. Potter

Under contractural arrangements with the Bureau of Mines, Mountain States Research and Development, Inc. (MSRD) completed a technological investigation to determine the feasibility of in situ mining of metal commodities other than copper and uranium, The study was based upon available literature and experience. The selection of potential candidates for in situ mining was influenced by economic importance, probable amenability to in situ methods, and environmental considerations. Four metals (or metal pairs) were chosen for feasibility studies: aluminum (with a copper byproduct), gold-silver, and manganese were recommended for further study and action; cobalt-nickel was also recommended contingent upon preliminary laboratory leaching and recovery investigations and field geohydrological work. Mining and recovery plans and an economic evaluation are included. Other metals with potential for in situ leaching are lead/ zinc, molybdenum, and vanadium.

Jan 1, 1981

By G. M. Wilemon

The U.S. Bureau of Mines has conducted investigations on extracting phosphate values from wastes generated during the mining and beneficiation of phosphate matrix. These wastes may contain up to one third of the phosphate originally present in untreated ore. Samples of wastes were air-dried and leached using 93 pct sulfuric acid in the presence of methanol. Evidence for the formation of a calcium sulfate hemihydrate coating that hinders complete dissolution of phosphate is presented. Solid-liquid separations were enhanced when flocculation was effected using poly(ethylene oxide) (PEO) in conjunction with hydroxypropyl cellulose (HPC) or hydroxyethyl cellulose (HEC. A conceptual flowsheet for a proposed process using an acid-alcohol leaching technique is presented.

Jan 1, 1990

By S. P. Singh

Drifts are the nerve centre of underground mining. They provide essential communications between primary openings and production areas. In view of their strategic importance in the overall safety, economy and productivity of mines, an empirical approach for blast design during drifting has been proposed in this paper. The approach was developed with the objective of minimum blast damage and provides computerized blasthole patterns for drifting operations. The drift blasting practices and problems in Canadian mines have also been reviewed in this paper.

Jan 1, 1991

By John Drew Ridge

Tables showing world trade in metallic mineral raw materials during the years 1953 through 1957 have been prepared for the following twenty-one commodities: alumina, aluminum, bauxite, chromite, copper concentrates, partly refined and fully refined copper metal, iron ore, pig iron, iron and steel (simple shapes), lead concentrates, lead metal, manganese ore, mercury metal, nickel ore, concentrates, and matte, nickel metal, raw pyrites, sintered pyrites, tin concentrates, tin metal, zinc concentrates, and zinc metal. In each instance, the amounts given by the importing country were used except when statistics from the importing nation were lacking, incomplete, or misleading. To show the considerable divergence between importing and exporting country totals for the same years, the complete mercury table is given and, in parallel columns, shows the comparable tonnages of importers and exporters. Tables for the other twenty commodities are presented in summary form. The data of the concentrate tables are used with those of the corresponding metals as a basis for a discussion of trade in concentrates versus trade in metals. The data of all twenty-one tables provide the basis for testing the thirteen rules governing international trade in metal raw materials which I first published in Mining Engineering for July 1955. Because the 1953 through 1957 data are far more complete and considerably more extensive than those on which the 1955 rules were based, it was found possible to deduce five additional rules and to modify three of the original thirteen appreciably. The full text of the eighteen rules is given.

Jan 1, 1960

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2013 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration for the year 2013: 1) budgetary statistics expressed in U.S. nominal dollars provided by SNL Metals & Mining (SNL) of Halifax, NS, Canada (formerly Metals Economics Group (MEG); 2) regional and site-specific exploration activities that took place in 2013 as compiled by the USGS; and 3) regional events that affected exploration activities, including economic, social and political conditions, that were derived from published sources and unpublished discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources are used to develop commodity and regional compilations, reported statistics may vary depending on the source and type of data that are being reported. The SNL data summarize planned company budgets for worldwide exploration activities in 2013 for 20 nonfuel mineral commodities based on surveys returned by companies primarily focused on precious metals (gold, platinum-group metals and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (coal, iron ore, phosphate and potash), and specialty commodities (diamond, lithium, niobium, rare-earth elements, tantalum and uranium). Information on uranium exploration activities was included in the MEG overview for the first time in 2007. MEG included data on the commodities lithium, niobium, phosphate, potash, rare-earth elements and tantalum for the first time in 2010 because of the increased topical significance of these commodities. Since 1999, companies with exploration budgets of $100,000 and greater were included in the MEG and SNL compilations. SNL budget estimates exclude aluminum, coal, and oil and gas. Budget estimates for iron ore have been compiled since 2011 but reported separately. The post-1999 budget surveys by MEG and SNL cover at least 90 percent of world?s reported nonferrous, nonfuel mineral exploration budgets; the 2013 survey is reported by SNL to cover an estimated 95 percent of these budgets. The 5 percent that is not covered is accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities.

By Jean-Michel Rendu

On April 30, 2003, representatives of the Society for Mining, Metallurgy and Exploration, Inc.(SME) met with the staff of the Division of Corporation Finance of the U.S. Securities and Exchange Commission (SEC). The meeting was held to discuss issues related to the estimation and publication of mineral resources and ore reserves. It took place in the Washington, D.C. offices of the SEC. SEC staff members included Roger Schwall, assistant director, Division of Corporation Finance; Jill Davis, senior accountant; Roger Baer, senior mining engineer; Carl Chavez, chief mining engineer; Ron Winfrey, senior petroleum engineer; and John Murphy, senior petroleum engineer. SME committee members included JM Rendu, independent consultant and chairman of the SME Committee on Resources and Reserves; Ian Douglas, manager of deposit modeling and reserve estimation with Newmont Mining; Art Graham, director and mining engineer with Deutsche Bank Trust Company Americas; Larry Smith, chief geologist with AMEC Mining and Metals Consulting; and George MacDonald, vice president of exploration with Freeport-McMoRan Copper and Gold.

Jan 1, 2003

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By Ralph W. M. Lai

The liquid membrane separation process was first patented in 1968 for separating hydrocarbons.(1-4) This stimulated many researchers to join in the area of separating organic compounds. l Since then, its applications have been extended to the removal of contaminants from waste water,(12-33) encapsulation of enzymes and/or microorganisms for reaction and/or separation, (24-28) oxygenation of blood (artificial lung),(19) removal of toxins from blood (artificial kidney)(26,20) and metal extraction.(31-63) This paper discusses the possible process schemes for using liquid membranes to separate and concentrate copper ion from its acidic leaching solution.

Jan 1, 1982

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal, and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely. In this study, the failure energy partitioning of Nugget Sandstone specimens is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrate a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining-induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

Jul 1, 2020

By Monserrat Rebolledo, John L. Uhrie, Candice Simms

Jetti Resources has developed a catalyst which overcomes the passivation of primary sulfides, enhancing the heap leach recovery of copper from chalcopyrite. It is important to emphasize that heap leaching of copper sulfides, whether with or without the Jetti catalyst, is a biooxidative process. We have demonstrated the efficacy of Jetti’s technology in bioreactors, with a chalcopyrite-dominant porphyry ore. In the presence of Jetti’s technology, optimal bioleaching conditions significantly increase copper extraction by 2.6 times that of the baseline.

Feb 1, 2025

By Zhonglin Ye, Guangping Dai, Ba Zhang, Yonggang Wei, Shiwei Zhou, Bo Li, Hua Wang

Decreasing copper content in slag is critical for improving copper recovery, where apparent viscosity is the main factor affecting the separation of matte/copper from the slag. The viscous behavior of copper converter slag was investigated during reduction process in this paper, and its non-Newtonian viscous behavior and shear thickening characteristics were clarified. The effects of silicate structure and solid particles in the melt on the slag apparent viscosity were investigated. As slag cleaning proceeded in an electric furnace, the magnetite gradually transformed into ferrous oxide, increasing the FeO/SiO2 ratio. With this ratio increased from 1.2 to 2.0, the slag structure was simplified, and its apparent viscosity decreased from 0.26 to 0.12 Pa·s at 1523 K. The iron phase was excessively reduced to metallic state; the slag contained metallic copper-iron alloy particles, increasing apparent viscosity. The apparent viscosity and phase structure of the slag corresponding to the iron phase reduction process were analyzed in detail; the results obtained in the present study are of great significance to the reasonable control of the converter copper slag cleaning process.

Nov 7, 2022

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021