Search Documents

By Richard E. Beane

For several decades, the minerals industry has used leaching techniques to extract metals from rocks whose grade was too low to be treated profitably using conventional metallurgical techniques, and, as of 1972, about 15% of domestic copper production was derived using leaching methods (Beall 1). Increasing interest is currently being directed toward solution mining, particularly with respect to copper, for basically two reasons. In the first place, geological exploration has outlined several copper deposits of large tonnage and 1m', grade which are buried at sufficient depth to preclude open-pit mining which would make such mineral deposits ore deposits. Nevertheless, these occurrences provide significant potential if they could be treated by chemical leaching in situ. Secondly, the porphyry deposits of the western united States, which provide by far the largest percentage of domestic copper, do not terminate geometrically with sharp borders. These large disseminated bodies commonly decrease in grade laterally away from volumes of rock containing ore grade metallization, and the distinction between ore and waste is strictly economic. In order to extract ore grade material from the ground, a significant amount of rock containing sub-ore-grade copper must also be removed which, when placed on dumps, is amenable to solution mining. These two considerations clearly indicate the reasons for the growing interest in solution , leaching techniques--namely the ability to exploit deeply buried low grade deposits and the expansion of reserves in deposits currently under production.

Jan 1, 1977

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By W. H. Schiffbauer

The U. S. Bureau of Mines has been investigating methods and technology that, when applied to existing continuous coal mining machines, may improve production and safety. Toward those goals, a microcomputer network has been designed that provides automated control and monitoring of all mining machine systems using a single twisted pair cable (two conductor stranded wire twisted together to provide a level of noise rejection). The network also provides -connections for intelligent sensors and systems for navigation and diagnostics. The flexibility of the network is demonstrated in that features can be added and removed without redesigning the whole system. A general description of the network's integration to a Joy' 16CM, Joy 14CM, Jeffrey 102, and a custom built auger machine is provided. The microcomputer networks for the Joy 16CM and the Jeffrey 102 have been installed onboard the mining machines and have been extensively tested at the Bureau of Mines test facility. The Jeffrey 102 system has also been tested in an actual highwall coal seam. Both systems have performed satisfactorily. The microcomputer networks for the Joy 14CM and the Auger Miner have been tested and await installation on the respective machines.

Jan 1, 1990

By Hakan Uyguçgil, Beril Bayraktar, Adnan Konuk

Mining is one of the industries with the highest risk of occupational accidents in Turkey and globally. The most important feature that distinguishes the mining industry from other sectors is the constantly changing working conditions. The risk of accidents is very high, especially in underground mining, and can happen for several reasons. Therefore, it is essential to carry out all necessary measures in coordination with other disciplines to adapt to changing workplace conditions. The dangers that might occur underground must be determined in advance, controlled at their source, or eliminated since it is critical to take the necessary precautions before the accident. Accident prevention will protect miners’ living conditions by contributing to the country’s economy through reduced labour and production losses. In this research, the data from 13,653 accidents reported in the Karadon Hard Coal Enterprise between 2000 and 2011 were analysed and compared using the Life Table and the Kaplan-Meier methods. Accident records were classified and analysed into four categories: environmentalrelated accidents, equipment-related accidents, person-related accidents, and other accidents. Findings in terms of survival time indicate that environment-related and person-related accidents had the highest risk in Karadon, with equipment-related accidents having the lowest. This study established the reliability of using survival analysis methods to investigate occupational accidents in the mining sector. Given that environment-related and person-related accidents occur in a relatively short period, such as 1 year after starting work, it has been recommended that research be done to improve workplace and occupational safety measures and broaden the training given to miners. Additionally, it has been determined that increasing the use of automation and mechanisation in underground coal mines, combined with developing a thorough equipment safety training programme to raise awareness of the danger, can help prevent person-related occupational accidents caused by the interaction between equipment.

Aug 5, 2023

By M. Ralchenko, C. Samson, M. Svilans, C. Walsh

"Through-the-Earth (TTE) radio has been proposed as a means of emergency communications in mines. The propagation of a TTE radio signal depends chiefly on the subsurface conductivity distribution. Robust forward models of signal propagation can be computed based on a realistic conductivity estimate. These models can be used, for example, to optimize frequency, estimate signal range, identify zones of anomalously strong or weak signals, or to optimize the position of the above-ground TTE radio unit. A method was developed to determine the conductivity distribution of a mine overburden using TTE radio transmission data. At multiple locations in an underground test mine, we recorded a wideband electromagnetic signal, spanning a frequency range of approximately 500 to 8,500 Hz, transmitted from a vertical magnetic dipole at the surface. Using a finite-difference time-domain forward modeling code, a layered Earth conductivity model that accounts for topography was fitted to the observed data, which minimizes the difference between the calculated and observed attenuations for each transmitter-receiver pair, for each frequency of interest. Introduction and objectiveThrough-the-Earth (TTE) radio has been proposed for emergency underground communications. The most common type of TTE radio is based on the transmission and reception of signals by electromagnetic induction. These signals are in the extremely low to very low frequency range — in practice, between 400 and 9,000 Hz. This technology was historically developed for mine safety, although recently other applications have been suggested, such as communications in civilian infrastructure like high-rise buildings or tunnels, in the military, and even for wireless detonation and activation. In a coal mine, which is a setting of particular importance for TTE radio due to the higher risk of accidents, day-to-day communications can be done through a wired link. High-frequency line-ofsight systems, whose signals cannot penetrate rock, are also used for communications from nonfixed points. Another option is a leaky feeder system, which is a permutation of a line-ofsight system and a wired link, where a partially shielded coaxial cable allows the signal to “leak” (Delogne, 1982). In an incident such as a mine collapse or explosion, a TTE radio system can still provide a communication link, as wired systems can be severed, and line-ofsight systems cannot penetrate through collapsed portions of the mine, or to the surface (Forooshani et al., 2013; Yarkan et al., 2009)."

Jan 7, 2018

By Gino Vogt

In mechanized tunnelling operations, performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequately dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole project. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer’s point of view.

Dec 1, 2022

By Bernie W. Martin, Raymond Leray, Christian Criado

Aguas Argentinas,1 a consortium managed by Lyonnaise des Eaux of France and operator of the world’s biggest privatized water supply and waste water collection system for the City of Buenos Aires, a city of 9 million people, was faced with the daunting task of providing new service to 1.6 million more people in the first five years of their 30 year concession. Aguas Argentinas elected to use the Negotiated Compressed Process - NCP - for the fast track implementation of a 15000 meter, 3,5 meter diameter tunnel, a key component of the infrastructure master plan. NCP was developed by Klohn Crippen for the $200 million international railway tunnel between Canada and the United States. The conceptual design of the project was performed by Safege Montgomery-Watson, who engaged Klohn Crippento assist with the NCP, the preparation of the tender documents, and implementation of theproject during construction. The process included the purchase by the client Aguas Argentinas of two sophisticated 4 metre diameter earth pressure balance tunnel boring machines from Herrenknecht of Germany. Construction of the tunnel is being performed by the consortium Wayss & Freytag (Germany) and Sollazzo Hnos S.A. (Argentina). The water tunnel is being built with a one pass, bolted segmented gasketed reinforced concrete liner. The purpose of this paper is to describe a transferable methodology for this innovative contracting procedure, the project organization and quality control plan for this important world class tunnel project which is designed to service one of Latin America’s largest metropolitan areas.

Jan 1, 1997

By Richard DePew, Robert J. Auber

The Westerly Storage Tunnel is a 25-foot diameter segmentally lined storage tunnel that is a major component of the Northeast Ohio Regional Sewer District's Project Clean Lake that is designed to capture 39 million gallons of untreated CSO overflows from entering Lake Erie. During the final stages of the project completion, a large-scale rock fallout incident occurred during the final lining installation operations at the down-stream end of the tunnel that extended beyond the designed primary support system. This paper outlines the level of coordination and collaboration between the Owner, Designer and Contractor to remediate the situation safely, quickly and effectively.

Jun 23, 2024

By J. A. Murray

Maintaining satisfactory air quality in electrowinning tankhouses is problematic and costly, particularly as plant operating current densities have increased. Conventional approaches have not proved completely effective. These include the use of beads, hollow spheres, surfactants and coalescer devices. They require powerful ventilation systems to be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses.

Jan 1, 1996

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By S. A. Diatchkov

There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices .

Jan 1, 1995

By William X. Chavez

The Mantos Blancos copper-silver district, a major copper-producing area since 1961, is located on the Tropic of Capricorn about 45 kilometers northeast of the northern Chile port city of Antofagasta, as shown in Figure 1. Copper oxide minerals occurring as atacamite (Cu C1(OH)3) and chrysocolla (copper silicate-hydrate) were discovered in the district in the early 1900's (Knobler and Joseph, 1962). The mine is situated in the northern Atacama Desert, one of the most arid regions on earth, and presently receives less than 1 cm per year of precipitation. The extreme aridity of the Atacama Desert is thought to have prevailed since at least Middle Miocene time (Mortimer et al., 1978) when development of important supervene copper enrichment was slowed in many areas of northern Chile (e.g., Chuquicamata, Exotica). Despite the paucity of precipitation, landform development is mature, with large alluvial fans and alluvial-filled valleys covering much of the region. In addition, the aridity and presence of salts have led to the formation of a sub-surface cementing of alluvium and colluvium by halite-rich caliche ranging from a few centimeters to over 3 meters in thickness. These factors, resulting in poor outcrop exposure, make even reconnaissance mapping difficult.

Jan 1, 1983

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques have been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

Feb 23, 2014

By D. J. McCracken

During 1995, the estimated consumption of lithium minerals in the western world was 139 kt (153,000 st).This amounted to 18 kt (20,000 st) of lithium carbonate equivalent (LCE). Overall tonnage demand for lithium minerals increased by 10.8 kt (11,900 st) during 1995from 1994. From 1992 to 1995, overall tonnage demand has increased 62%, from 85.5 to 139 kt (94,240 st). There are four major producers of lithium minerals. Gwalia Consolidated in Western Australia is the largest producer of spodumene. It supplies high-grade spodumene concentrate, fine-spodumene concentrate, glass-grade spodumene and chemical-grade spodumene.Tantalum Mining (Tanco) of Manitoba, Canada, produces high-grade spodumene concentrate, fine-spodumene, concentrate and montebrasite. Bikita Minerals in Zimbabwe is the largest manufacturer of petalite. It supplies high-grade and container-glass petalite.

Jan 1, 1996

By L. Sandbak

The TRJV Mine is located approximately 43 miles northeast of Winnemucca, along the east flank of the Osgood Mountains in the Potosi Mining District, Humboldt County, Northwest Nevada (see Figure 1). The Turquoise Ridge Mine is an underground mine, and is a 25% joint venture partner with Newmont Mining. The TRJV mine utilizes the underhand cut-and-fill mining method due to the relatively low rock quality in the ore zones and the relatively shallow dipping 25-45 degree ore body geometries. This paper defines a rehabilitation risk rating system (RRRS) for prioritizing rehabilitation of drifts damaged in the mining processes including long term development drifts providing access to the mining areas. The ultimate use is as a mine planning tool for the organized scheduling of rehab in a timely manner. A few case studies of the most needy rehab areas identified by the RRRS mapping system is presented, and the type of rehab completed design for these areas. Suggestions on improving the rehab risk mapping system include the use of support history and rock mass strength rating factors.

Feb 23, 2014

By Jackson M. Langton

INTRODUCTION The Morenci-Metcalf district is located on the southern slope of the white Mountains in Greenlee County, Arizona. Both porphyry copper deposits are four to six miles northwest of Clifton, the county seat, and the new Metcalf mine is situated approximately one mile northeast of the Morenci open pit (Figure 1). Chase Creek, a south-flowing tributary of the San Francisco River, dissects the district and separates the two ore bodies. More than 1,200 exploration and development drill holes have been completed in the district and the Morenci-Metcalf ore bodies have been delineated on a 400-foot grid. Recently initiated drilling programs have revealed new data about deeper protore and associated hypogene alteration. This information, correlated with surface mapping and petrographic studies, was utilized to propose a plausible geochronologic sequence for this region. The reasoning behind this study has been helpful in locating new ore beneath leached capping indicative of only protore mineralization. The scope of this paper is to establish a practical solution to a highly theoretical problem of ore genesis and to familiarize the reader with stratigraphic, structural, and mineralogic events responsible for localizing ore in this district. Continued research will possibly alter the proposed time span and relative displacements, but it is doubtful that the order of events will vary significantly. Geochronologic conclusions are therefore presented as general hypotheses and additional geologic mapping,

Jan 1, 1972

By W. D. Macleod

This paper describes a mineral dressing process for the upgrading of tin ores. The process described is called 'agglomeration' and. is similar in many respects to flotation. Many variables have been examined experimentally both on batch and continuous operations and are reported upon herein... Using a Mt. Pleasant tin ore, assaying 0.5% Sn, an upgrading to 8% Sn, with a recovery of 95% could be obtained by this process.

Jan 1, 1966

By J. A. Ober

China, Mexico, Spain and Turkey are the leading producers of celestite (strontium sulfate), the most common strontium mineral. Of an estimated 510 kt (562,000 st) of celestite produced worldwide during 2004, 98 percent was produced in those countries. Deposits of strontianite (strontium carbonate), another strontium mineral, have been identified in China and Malawi. Relatively small quantities are reported from the deposit in China. Although celestite deposits occur in the United States, no domestic celestite has been mined since 1959.

Jan 1, 2005

By Del Brock, Dan Wooton

The design/build of two adjacent vertical mine shafts in difficult ground conditions at a mining complex in the midwestern United States required innovative construction techniques. Construction of the 267-m-deep Service Shaft required full depth dewatering wells and ground freezing. Blind drilling was utilized to excavate the 257-m-deep Production Shaft and it was finished with a steel/concrete composite liner that was floated into place. An equally unique component of the installation included supplying a high capacity vertical conveyor system, featuring a 273-m-lift. Other components of the project include the mine level development, as well as the design and installation of three hoisting systems, including a 45-ton capacity men/materials hoisting system.

Jan 1, 2003