Search Documents

By Janet A. Johnson, T. B. Borak, K. J. Schiager

INTRODUCTION In the USA regulatory agencies have adopted standards which limit the allowable concentration of ore dust in underground uranium mines. The American Conference of Governmental Industrial Hygienists has recommended a threshold limit value for silica which has been incorporated by reference in federal regulations (30 CFR 57, 1980). The Nuclear Regulatory Commission (NRC) imposes a limit for unprocessed uranium ore dust for reducing the exposure to radioactive materials from inhalation (10 CFR 20, 1980). We have been unable to trace the origin of the NRC standard. Recently the ICRP has published recommendations concerning limits for intakes of radionuclides by workers (ICRP, 1979). We have used the ICRP methodology to compute the dose equivalent commitment to lung and bone from inhalation of insoluble ore dust particles. These values were used to derive air concentrations which would provide an acceptable risk for induction of cancer from occupational exposure. Results indicate that the new ICRP recommendations are more restrictive than the present NRC standard for radioactivity. The maximum allowable dust load in a uranium mine will depend on both the concentration of silica (% Si02) and the amount of radioactivity (% U308). We have combined these standards assuming complete independence of biological hazard to establish boundary conditions for which either silica or radioactivity is the dominating factor. Based on these results we present suggestions for analysis of ore dust to insure compliance with regulatory agencies. SILICA STANDARDS Silicosis, fibrotic lung disease produced by crystalline silica, was one of the earliest forms of occupational disease to be recognized. The pulmonary lesions caused by silica, silicotic nodules, consist of concentrically arranged bundles of collagen fibers. Fusion of these nodules results in progressive massive fibrosis causing alveolar changes which decrease ventillation and blood flow in the lungs. The current Threshold Limit Value (TLV) for mineral dusts is based on the concentration of free silica. The standard is expressed in three forms: (1) Particle count standard: TLV (mppcf) = 300/(% Si02 + 10) (mppcf = million particles per cubic foot) (2) Respirable dust mass standard: TLV (mg/m3 ) = 10/(% respirable Si02 + 2) (3) Total dust standard: TLV (mg/m3 ) = 30/(% Si02 + 3) The most commonly used form is the respirable mass standard. These curent values for silica are based primarily on epidemilogical studies of Vermont granite workers and other occupationally exposed workers. In the Vermont study no cases of silicosis were seen in individuals employed after dust control measures were initiated and whose subsequent exposure averaged less than 5 mppcf. The free silica concentration in the airborne dust to which these workers were exposed averaged 25%. A concentration of 10 mppcf of granite dust is considered equivalent to 0.1 mg/m3 quartz. The current respirable mass standard allows a maximum silica concentration of 0.1 mg/m3. NIOSH (1974) has recommended a reduction in the current TLV for respirable silica to 0.05 mg/m3 Si02. As with radiation standards, the TLV for mineral dusts is an upper limit for time weighted average exposure. It is recommended that dust concentrations be maintained as far below the TLV as current practices permit. RADIATION STANDARDS The present concentration limit for airborne natural uranium in ore dust prior to chemical separation is 75 µg of uranium per m3 of air ( 10 CFR 20, 1980) . This corresponds to 1.85 Bq/m3 (50 pCi/m3 ) of natural uranium, U-238, U-235 and U-234 and is equivalent to 3.7 Bq/m3 (100 pCi/m3 ) of gross alpha activity with radioactive equilibrium between the long-lived alpha progeny through Ra-226. The origin or basis for this standard is not known, but it presumably includes both chemical toxicity and risk from somatic radiation injury. Recently the International Commission on Radiological Protection (ICRP, 1977) has published recommendations concerning the objectives and criteria for limiting radiation exposures. This was followed b y a revision of the limits for intake of radionuclides by workers (ICRP, 1979; ICRP, 1980). The previous compilation of limits for internal emitters was published by ICRP Committee II in 1959 (ICRP, 1959). The latest version includes new methodlogy outlined in ICRP Publication 26 (ICRP, 1977) as well as extensive metabolic information

Jan 1, 1981

By J. A. Cooper, M. R. Petersen, P. O. Jackson, J. C. Langford

The organic, inorganic, and radiological characteristics of airborne aerosols have been measured as a function of particle size in controlled atmosphere test chambers and operating uranium mines. Concentrations of benzo(a)pyrene in two mines ranged from 26 to 57 ng/m3 of air. The carbon chain length of adsorbed n-alkanes was correlated with particle size. Normal mining activities produced an ore dust aerosol with mass median aerodynamic diameter (MMAD) greater than 2 µm. The elements Na, Al, Si, K, Ca, Ti, V, Fe, and U exhibited elemental ratios similar to bulk ore and had comparable MMAD's. The S, Zn, and Pb were higher in aerosols than bulk ore and were associated with smaller MMAD particulates. Radon daughter particle size distributions were influenced by the kinds of particulates

Jan 1, 1981

More than 1,200 professionals from the global tunneling and underground space industries are expected to be on hand for the 2009 Rapid Excavation and Tunneling Conference to be held at Caesars Palace in Las Vegas, NV. The conference, set for June 14-17, is sponsored by the Society for Mining, Metallurgy, & Exploration, Inc. (SME) and the Construction Institute of the American Society of Civil Engineers. The four-day conference will feature more than 100 technical papers in 19 sessions. Two one-day short courses are also planned, as are a pair of field trips. And the show?s exhibit will feature more than 120 of the industry?s leading equipment and service suppliers.

Jan 1, 2009

By Georgene Renner

With more than 800 booth spaces sold and 540 exhibiting companies displaying their wares, there was something for everyone on the exhibit floor of the 2014 SME Annual Meeting in Salt Lake City, UT Feb. 23-26. The following is a sample of what was offered at the 2014 meeting.

By Mirjana Boskovic

LKAB’s Kiirunavaara Mine is a sublevel caving iron-ore mine located above the polar circle in northern Sweden. The mine has been proclaimed seismically active since 2008 after a magnitude 3 seismic event, according to Swedish National Seismic Network (SNSN). At that time the Kiruna Mine did not have mine-wide seismic system. Since then, the Kiruna Mine experienced several damaging seismic events of which the largest one on the May 18, 2020. The magnitude, based on the moment tensor inversion results on data from the SNSN as well as seismic stations in Finland and Norway, is estimated to 4.2 ± 0.2 moment magnitude. The seismic event on the May 18, 2020 was located in the middle of the one of the productions areas and caused the major damage in the mine, damaging several kilometres of drifts on six mining levels, some of them beyond the practical repair. These damages affected four of ten production areas on several levels, some more some less. Luckily, no person got injured from the seismic event and the very long aftershock series. An important part in the whole process after the seismic event was information flow and decision-making process. It was very important to keep workers and community informed as that contributed transparency of decision-making and decreased the speculations. Resuming the production in the damaged areas in the safe manner, very soon become main focus for the mine management. It was obvious that not only rehabilitation of the areas is needed to resume the production. It was A MUST to understand the factors behind the seismic event and its mechanism to be able to avoid same situation and prevent seismic event of similar size. Mine engineers had to think outside the box to find the solutions to ‘rescue’ every drift that they could to be able to make good enough base for continued mining of the area. The paper describes actions taken in a very complex process of recovering the area that we from the beginning thought need to be abandon. Seismological analyses of the event on May 18, 2020 and past activity in the area, damage mapping, detailed studies of structures and geology, numerical modelling as well as engineering judgement were used as base for all our decisions how to proceed in attempt to restore mining of the area heavily damaged by 4.2 moment magnitude seismic event, in a safe way.

Apr 26, 2022

By M. Mustafa Kahraman, Sean Dessureault, W. Pratt Rogers

Most contemporary mines have considerable amounts of data. Structured and unstructured large data sets are colloquially named big data. Much of the data in mining operations come from a variety of systems, each with different databases and reporting environments. Standard technology deployments create a Bsilo-ification^ of data leading to poor system benefit. Through modern server monitoring and systematic approach, data utilization and value can quantifiably be measured. The Data Utilization and Value Index (DUVI) can quantify business intelligence best practices and user interaction. This study seeks to provide a data management tool to measure data utilization across the process of converting data into action.

By Jian Zhou, Shuai Huang, Wenqin Xi, Kun Du

The deep oceans harbor a wide variety of mineral resources that are characterized by their abundance and high quality. Nations worldwide are actively pursuing the exploration and extraction of these resources. This paper provides a concise overview of the mineral resources found in the deep sea, highlighting the challenges associated with their exploitation. Furthermore, it presents a comprehensive analysis of the historical development of deep-sea mining technology and equipment, offering valuable insights into this field. By examining the current issues and obstacles faced in deep-sea mineral extraction, this study concludes that the future of deep-sea mining lies in the direction of automation, intelligence, and standardization. Additionally, it identifies the key technological advancements that need to be achieved in order to overcome the challenges associated with deep-sea mining.

Jan 5, 2024

By W. G. Pariseau

"BACKGROUND Strata mechanics of three underground coal mines in central Utah were recently studied using a specialized finite element technique [1, 2, 3, 4]. The purpose of these studies was to examine relationships between mining and related seismicity. The longwall mining method was predominant, but room and pillar mining and barrier pillar mining were also used in the mines studied. In every case, high correlation between face advance and seismicity was observed. The specialized finite element technique allows for whole mine subsidence estimation at a kilometer scale and for stress concentration at a meter scale near a working face. Comparisons of observed mine subsidence with model subsidence allows for model verification and justifies detailed analysis of the evolution of stress at seam level. Yielding is expected near a longwall panel face and as the face is advanced the extent of yielding is expected to increase. The total number of element failures in a finite element mine model also increases, so a high correlation with associated seismicity, say, event count, is not so surprising. A brief review of recent coal mine studies in Utah is presented in the sequel. The procedures are given in some detail in application to trona mining. COAL MINES The analysis procedure begins with the geologic column and proceeds to specification of strata properties including elastic moduli and strengths. Joints are an integral part of the geologic model and joint set specifications include dip direction, dip, spacing, stiffness and strength. Spatial variability of strata properties in situ may be taken into account during analysis. Topography is important, especially to Utah coal mines that are developed from outcrop in regions of high relief. Mesh generation follows specification of data input. Finite element analysis is next, followed by reporting of results. In this regard, all finite element computations are based on first principles. No model “calibration” is done that involves adjusting computer input to obtain a fit to mine measurements such as subsidence profiles. Figure 1 illustrates the concept of a dual node – dual mesh finite element concept. Dual nodes are roof and floor nodes in mined areas. These nodes replace the seam. The dual mesh is a much refined mesh with displacement boundary conditions obtained from the big mesh and thus replaces the effect of mining in the region outside the dual mesh. The refined dual mesh allows for details of stress, strain and displacement near a working face of interest. Strata Properties Strata properties include elastic moduli and strengths of intact rock between joints and joint stiffness and strength for each joint set present. Both properties sets may be obtained from laboratory test data, although testing joints poses a sampling problem in the field. The statistical variability observed in laboratory test data, say, in unconfined compressive strength tests is often characterized by much variation. In fact, the coefficient of variation, ratio of standard deviation to mean, is often greater than 35 percent. When sample values are mapped back to the mine location, one may observe spatial variability as properties vary from place to place as shown in Figure 2. Spatial variability may be incorporated into a finite element analysis with probabilistic assignment of properties to elements in accordance with measured variability. The result is a more realistic model of rock in situ."

Jan 1, 2017

By Satoshi Honda, Mitsuru Shimizu, Tatsuji Nagao, Motoaki Kurisu, Hirokazu Izumi, Toshinori Takahashi, Hiroyuki Itoi

"1. INTRODUCTION Grade separation of roads and railway tracks is an effective method for solving traffic-related issues in cities. However, in urban areas where the existing traffic infrastructure is already overcrowded, construction of new roads often faces problems especially in the proximity of existing structures. This paper summarizes the construction plan and results of new road tunnel construction in the proximity of the piers of elevated tracks on the Tokaido Shinkansen railway.2. SUMMARY OF CONSTRUCTION AND ISSUES Auxiliary Route No. 26 as specified in the Tokyo urban plan is a project by the Tokyo Metropolitan Government, covering the construction of a new road with a total length of 22.3 km currently on the way to completion. In Shinagawa Ward, Tokyo, Auxiliary Route No. 26 is designed to cross the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line, so for this project, the East Japan Railway Company (JR East) was commissioned to design and build a road crossing under the railway tracks (Sumiyoshi Underpass). Figures 1 through 3 show a sketch of the Sumiyoshi Underpass. The Sumiyoshi Underpass was planned as a two-lane tunnel for vehicles, which was to cross under the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line at an angle of 70 degrees. The structure concerned is a single-story single-span box culvert structure with the following dimensions: 11.5 m wide, 7.7 m high and 31.6 m long. The Tokaido Shinkansen Line tracks were constructed on a girder-type elevated bridge built in the 1960s, and the foundation piles of the piers (P7 and P8) in the proximity of this crossing box culvert of RC structure were constructed using an earth drill method. The crossing structure for this project is located extremely close to the piers of the Tokaido Shinkansen railway tracks, with a minimal separation of 0.4 m, and the most significant issue of this project was construction in a manner that would not obstruct the normal operations of the Tokaido Shinkansen (Figure 4). Initially, we considered installing a temporary earth retaining structure in the proximity of the piers, cutting the ground and building an RC box, but concluded that it would be very difficult to apply this method because of probable excessive displacements in the Shinkansen railway piers. That is why we decided on the use of a non-open cut method in order to minimize the impact on the piers."

Jan 1, 2016

By J. L. Ellenberger, G. S. Esterhuizen, T. Miller, M. M. Murphy

A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor convergence monitors were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.

Jan 1, 2015

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

By Frederick J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for the coal industry — particularly in Asia — the power plants being planned or under construction are designed to use coal as fuel. This has produced a significant increase in the demand for steam coal that, in turn, has encouraged many in the industry to develop new coal mines. Indonesia is a country that has enjoyed substantial growth in coal production. This developing country has 195 million people who live on the nearly 13,000 islands. It has quickly emerged as the third-largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface-mining methods.

Jan 1, 1996

By G. E. Agar

In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to be done, wet or dry or a combination?

Jan 1, 1995

By John Jonkman

The cost of equipment maintenance is the largest single expense at many mines and processing plants. It is not unusual for a maintenance and repair budget to be larger than 50% of the punt's total budget. Generally, in the mining industry, 400-60% of the work force in a plant reports to the maintenance department. Studies have shown that many plant maintenance workers are only 33 to 40% productive, working 2.6 to 3.7 hours of every 8-hour day. In recent years, many companies have begun to recognize that- productivity improvements and cost reductions can he achieved by upgrading maintenance methods. This paper discusses ten common causes of low maintenance productivity and how recent advancements in computing technology can be utilized to address these causes for low productivity.

Jan 1, 1986

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

In this study, the oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bismuth (Bi), lead (Pb), antimony (Sb), arsenic (As) and copper (Cu) contents in the speiss by two-step simulation differed from the industrial data by 0.6, 0.8, 2.6, 7.2 and 8.6 weight percent, respectively. The two-step simulation results indicate that the speiss partitioning of Sb, As and Cu increased from 60.1, 32.3 and 27.5 percent to 81.6, 67.8 and 47.2 percent, respectively, with the smelting temperature increasing from 1,050 to 1,250 °C, while the metal partitioning of Sb and Cu increased from 0 and 2.7 percent to 15.2 and 13.3 percent, respectively, with the separation temperature increasing from 400 to 700 °C.

By T. M. “Mike” Gurr

"U. S. marketable phosphate rock production for the 2018 crop year (July 1, 2017 to June 30, 2018) showed an increase to 27.7 Mt (30.5 million st) from the 2017 crop year production of 27.1 Mt (29.8 million st), as reported to the U. S. Department of the Interior by the mining companies operating in the United States during crop year 2018 (Table 1). Domestic consumption decreased in the 2018 crop year to 23.9 Mt (26.3 million st), as compared to the 27.2 Mt (30 million st) consumed in crop year 2017. U.S. imports of phosphate rock increased to 3 Mt (3.3 million st) for the 2018 crop year from the 1.81 Mt (1.9 million st) for crop year 2017. Imports of phosphate rock were from Peru and Morocco. There was an increase of 2.85 Mt (3.1 million st) in producers’ stocks from 7.45 Mt (8.2 million st) in crop year 2017 to 10.3 Mt (11.3 million st) in crop year 2018 (Table I).For calendar year 2018, Florida and North Carolina phosphate rock production accounted for 75 percent of the total U.S. production, with the balance being produced in Idaho and Utah. The Florida and North Carolina percent of U.S. production is declining. U.S. production of 25.7 Mt (28.3 million st) in calendar year 2018 was produced by five companies at 10 mines in four states and accounted for approximately 9.6 percent of the world production of 267.7 Mt (295 million st) for calendar year 2018 (Table 2).In calendar year 2018, U.S. phosphate production decreased by 2.2 Mt (2.4 million st), while companies increased stocks of phosphate rock by 1.7 Mt (1.9 million st). The domestic production for calendar year 2018 of 25.7 Mt (28.3 million st) represents 78.4 percent of the domestic production capacity of 32.8 Mt (36.1 million st).At present, China reportedly produces more than 50 percent of the world’s phosphate rock. As a result of planned expansions, Morocco production has increased from 27 Mt (30 million st) in 2017 to 33 Mt/a (36 million stpy), which is approximately 12.3 percent of the world’s production, moving ahead of the U.S. production. In calendar year 2018, the U.S. phosphate rock production was 25.7 Mt (28.3 million st), which is less than 10 percent of the world’s production of phosphate rock (Fig. 1)."

Aug 1, 2019

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By J. P. Wilson, T. Cook, H. Kling

The Tessenderlo-Kerley Leachprocess has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia andammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999