Search Documents

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

By M. S. Klima, V. Choudhry

Coal gasification solid residue (slag) contains unconverted carbon (char) which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal -3.4 mm gasifier slag (~85% ash) to separate high (~100%) ash slag from low (~50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71% was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1 mm in size.

Feb 24, 1997

By J. G. Davis

The St. Peter Sandstone is typically a well-sorted, friable, ultra-pure, fine- to medium-grained, quartzose sandstone with silica content higher than 99 weight percent in places. The sand grains are well-rounded, highly spherical and characteristically frosted. Their size typically varies from 2 millimeters diameter (No. 10 U.S. Standard Sieve Series size) to less than 0.08 millimeters diameter (No. 200 U.S. Standard Sieve Series size). A freshly exposed surface of the formation is commonly white with shades of pink and green. Weathered surfaces are a dirty gray or brown and are case-hardened at many localities. Bedding is characteristically indistinct, and the formation usually appears massive throughout. The rock is cross-bedded and ripple-marked locally. The formation is generally porous, permeable and rarely fossiliferous in Missouri. The St. Peter is continuously present in the subsurface in the northern half of the state and along the southeastern edge of the state. The St. Peter crops out in a narrow band that starts in western Montgomery County and runs southeastward, along the Missouri River, to just west of St. Louis and continues south, just west of the Mississippi River, through Scott County. The outcrop belt varies from less than one mile wide to over ten miles wide, and it is over 150 miles in length. The formation dips into the subsurface radially away from the outcrop band. A notable isolated outcrop occurs in Lincoln County to the north of the main outcrop band. The St. Peter is discontinuously present in the subsurface along a band in the west-central portion of the state. It is not present at the surface or in subsurface in the remainder of the state. The formation averages 80?100 feet thick. There is an estimated 3.8 trillion short tons of St. Peter in Missouri. Sieve analyses on drill cuttings indicate three subsurface locations in northeastern Missouri where the St. Peter is greater than 10 percent by weight of sand falling in the 20?40 U.S. Standard Sieve Series size range. The St. Peter was first produced in Missouri in the 1870s for the manufacture of glass. Since that time it has been used as a paint additive, filler material, polishing compound, filtering media, and recently it is commonly used as a fracture proppant in oil and gas wells. The St. Peter is currently quarried and produced in Missouri from four sites located in St. Louis, Jefferson and Perry counties. In the same area there are at least nine abandoned historic mine sites.

Feb 27, 2013

By J. Winterton

Estimating the residual metal inventory of large heap leaching operations is desirable for many reasons. Several methods have been tried with limited success. Drilling data from the Valley Leach Facility at AngloGold Ashanti's Cripple Creek and Victor Gold Mine has been used to develop a robust inventory estimation technique. The technique is presented along with discussion of the particular inventory components and evaluation methodologies.

Feb 27, 2013

By P. C. Holloway

La Oroya zinc ferrite (19.5% Zn, 26.6% Fe, 0.052% Ga, 0.075% In) was roasted with coal under conditions more oxidizing than normally used in a Waelz kiln, and the roasted residues were leached with 200 g/L H2SO4. Overall zinc recoveries of up to 97% were achieved, with 35% of the zinc reporting to the fume after roasting at 1,100°C with a bituminous coal addition of 20%. Under these conditions, 93.2% of the Cd, 13.4% of the Cu, 33% of the Ga, 61% of the In and 18.2% of the Pb were recovered either in the fume or in the leach solution. At 2006 metal prices, the value of the recovered metals is comparable to that obtained from commercial Waelz kiln processing of this residue. Zinc in the franklinite (ZnFe2O4) mineral is reduced to zinc vapor, and, after oxidation, some of the zinc is found as ZnO or as Zn2SiO4 in the roasted residue. Iron reacts to form either hematite (Fe2O3) or magnetite (Fe3O4), with no metallic iron detected in the roasted residue, and less than 2% of the iron is solubilized during leaching. The residue produced after roasting and leaching is, therefore, much more stable than the residue from Waelz kiln processing and should be suitable for disposal in a landfill.

Jan 1, 2008

By J. J. Gresham

Homestake’s first links with Australia were established in 1934 but it wasn’t until 1961 that the company established a formal presence in the country. After involvement and success in iron ore and nickel, Homestake made a strategic investment in the Kalgoorlie gold operations in 1975 and now owns 50% of Kalgoorlie Consolidated Gold Mines, operators of Australia’s biggest gold mine. In 1998 Homestake acquired the major Australian gold producer Plutonic Resources, is now firmly established as Australia’s second largest gold producer and is actively seeking further opportunities for growth in the Austral-Asia region. Homestake’s success in Australia has been the result of important strategic alliances, timely investments, a long term commitment to the region and perseverance during periods of depressed commodity prices.

Jan 1, 2001

By Jamal Rostami, Richard Kastner, Ahmad Ramezanzadeh

Improving the accuracy of the performance prediction models for hard rock Tunnel Boring Machines (TBMs) is important in estimation of the schedule and cost of tunnelling in related projects. The effects of rock mass on performance of TBMs has been studied extensively, yet due to the complex nature of the process, impact of many parameters influencing machine advance rate are not very clear and there is still room for improvements. More accurate estimates can be obtained by better understanding of operating parameters in various geological conditions and can lead to matching machine specifications with job conditions, optimizing machine performance, and avoiding long delays and downtime for increased productivity. This paper will offer review of two case histories including Queens Water tunnel in New York and KCRC project in Hong Kong. The analysis of the available field data, including the geological back mapping and results of laboratory testing of rock mechanical properties, machine operational parameters and achieved rate of penetration will be presented. This includes statistical analysis of available field data to provide a better understanding of the influence of rock mass properties on performance of hard rock TBMs as well as related formulas to improve performance estimates.

Jan 1, 2005

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By Cathleen J. Webb, Arden D. Davis

The Homestake Gold Mine at Lead, South Dakota, has been proposed as the host site for the Deep Underground Science and Engineering Laboratory. The laboratory will house neutrino experiments in mine workings at the 7400-foot depth, as well as research in geomicrobiology, rock mechanics, and ground-water flow. Initial plans for the laboratory were developed in 2000 after Homestake Mining Company announced the closing of the underground gold mine. Homestake’s owner, Barrick Gold Corporation, had agreed to donate the mine for a laboratory if it could be protected from environmental liability. That initial agreement was delayed, and Barrick turned off the mine’s pumps in 2003, allowing lower levels of workings to begin to flood with water. In early 2004, the Governor of South Dakota signed an agreement with Barrick that would indemnify the company and eventually transfer ownership of the mine to a state laboratory authority. South Dakota’s governor also announced plans to ask the state legislature for funds to help in the initial construction of the laboratory. A consortium of scientists from several states is currently preparing a detailed laboratory proposal for the National Science Foundation.

Jan 1, 2005

By M. J. Price

The usage of Geographic Information Systems (GIS) is increasing rapidly throughout the Mining Industry, especially in the Industrial Minerals sector. GIS provides an efficient and robust link between spatial (often CADD) and tabular (database/spreadsheet) components. Mineral economists and corporate planners employ GIS to perform market analyses, to source raw materials, and to schedule and monitor deliveries to customers. Exploration and acquisition groups apply spatial analysis to identify high quality resources that meet economic guidelines. Mining regulators and environmental affairs departments expedite and monitor permitting, environmental compliance, and best management practices reclamation through GIS data management and Electronic Permitting. Operations staffs monitor overburden removal, material extraction, quality control, and stockpile volumes with GIS. This paper summarizes the many aspects of GIS in Industrial Minerals. It also introduces and addresses issues and concerns commonly encountered during a mining GIS implementation.

Jan 1, 2001

By H. R. Hardy

Whether the mining engineer is concerned with stress problems in a mine at depth, the development of a new drill bit, or the efficiency of a comminution process, the mechanical properties of the rock with which he must work are of the utmost importance. One of the most popular topics in rock mechanics circles today is ?Is it possible to utilize directly parameters determined from laboratory tests on rock specimens in the analysis of mining engineering problems?? It is the author's opinion that laboratory and .field investigations have not yet reached the stage of development where this question can be answered with any degree of certainty. At present, great difficulties are involved in applying the results of laboratory tests to a mining engineering problem. However, this is due in part to the lack of detailed measurements of stress and deformation in the field and in part to the lack of development of satisfactory structural theories to correlate laboratory and field measurements. Furthermore, if mechanical properties measured in the laboratory are to be directly applied to the analysis of mining engineering problems, the critical mechanical properties must be identified, reliable test procedures must be developed and extensive test programs must be carried out.

Jan 1, 1964

By H. Seguin, J. A. Le Gac, S. Bernhard, P. R. ZETTWOOG

The "Service de Protection Technique"of the "Institut de Protection et de Sûreté Nucléaire" was asked by the Commission of European Communities to conduct measurement campaigns which would make it possible to evaluate, on an experimental basis, the collective risk to miners exposed to radon in underground, non-uranium mines located in countries within the European Community. 1. METHODOLOGY USED TO CONDUCT THE CAMPAIGNS This campaign is original in that direct measurements of the individual monthly exposure to potential [a]-energy from short-lived radon daughters are made using personal [a]-dosimeters described previously (1). We call this type of dosimetry "personal dosimetry". The workers who wear the personal [a]-dosimeters were selected taking into account the various categories of workers and their work assignments in the various areas of the mine. Another way of finding out the occupational exposure of these miners consists in making numerous measurements of the radon concentration at the various work places, taking into account the time spent at each place by each worker. This procedure is too complex for an evaluation of the collective risk as requested by the Commission of European Communities and was therefore rejected. Additional data was gathered during these measurements campaigns using the following techniques (table 1). [ ] (1) Current [a]-dosimetry as practiced in France - SPT international report N° 234 - February, 1981 - P. ZETTWOOG The mines were chosen to include a larger variety of types of ore, of geological situations, and of mining methods. 2. RESULTS OF THE RADON DATA-GATHERING CAMPAIGNS 2.1 – [Uranium content of the surrounding rocks and ore] The samples taken during the campaigns make it possible to establish the U content in the rocks of the mines selected. These values, from 2 to 15 ppm, are slightly higher than those usually found (2 to 5 ppm) (table 2). [ ]

Jan 1, 1981

By S. K. Palm

The commercial life of a mineral product can be long, but like hitech electronic and software products that soar in sales one day to become obsolete and forgotten a few months or years, mineral products have a life cycle. They are invented, commercialized and eventually decline and disappear from commerce. Diatomite and perlite are produced from mined minerals, but almost none of the products in these industries spring from the earth in finished form. Straight calcined diatomite was invented over 100 years ago and flux calcined diatomite just a few years later. The expansion properties of perlite were discovered and first exploited about 75 years ago. Some applications for diatomite have disappeared or currently face competition from newer products. Dry cleaning was once the second-largest application for diatomite but disappeared over 30 years ago. Both the beer and wine filtration markets for diatomite face increased competition from membrane filters. A pipeline of new, proprietary products is critical to the future of the industry.

Mar 2, 2022

By Sakai Kunito, Nigel B. Sugden

If an Earth Pressure Balance (EPB) TBM is operated effectively tunneling can be carried out producing negligible ground movements. Using the methods given in this paper face losses of the order of 0.5% and less are generally obtainable using an EPB. Operating the EPB TBM in this manner reduces the requirement for the building protection measures used to protect surface structures. This can result in a considerable cost saving for the construction of a tunnel under built up areas. This paper to give guidance on the causes of ground movements around a TBM and the methods of running an EPB TBM that will minimize those movements. Details of how this was successfully done during the construction of the Bangkok Metro are given. The paper is split into three parts as below. 1.Causes of ground movements due to TBM tunneling 2.Methods of controlling those movements using an EPB TBM 3.Case history Bangkok Metro (water main)

Jan 1, 2001

By Ian Farmer, Nigel Glossop, Philip Garritty

Performance of tunnel boring machines - usually expressed in terms of penetration per revolution - is determined by relations between machine thrust and torque, head diameter and rock strength. It can be shown that for a given machine power and head diameter there is only one rock strength at which the machine performs optimally. In weaker rocks the available torque limits performance and in stronger rocks, the available thrust. Performance data shows that, historically, machines have been designed to cut weaker rocks. Optimization of thrust is required to improve performance in stronger rocks.

Jan 1, 1987

By John E. Tilton

During the past several years — much to the delight of producing firms and countries — copper prices have surged from under $1 to more than $3/lb. Anyone familiar with the industry also knows that since the early 1970s the long-run trend in real copper prices has been significantly downward. This sharp contrast between short-run and long-run trends raises the issue of the forces behind these developments. What has been driving short-run prices up and long-run prices down? Simple economics suggests that it is all a matter of supply and demand. When demand is rising faster than supply, prices will rise and vice versa.

Jan 1, 2006

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008

Scattered north and south along a 161-km (100-mile) stretch of Interstate 80, Newmont Min¬ing Corp. owns four active mining properties in Nevada?s northern high desert ? Carlin Trend Operations, Midas, Twin Creeks and Phoenix. Among the four, there are nine openpits, five underground mines and 14 processing facilities. While gold is the predominant ore, silver and copper are also produced. And in a move to hold down energy costs, Newmont built and owns the 200-MW (net), coal-fired TS power plant. This plant provides about 65 percent of the power used for Newmont?s own operations, while the rest is sold to NV Energy, which services Nevada and northeastern California. Bringing the Phoenix Mine ? Newmont?s newest in Nevada ? on-line presented many developmental and operational challenges. Located about 19 km (12 miles) southwest of the town of Battle Mountain, the general area had been home to prospectors and other mining companies since the 1860s. But any profitability in developing the lower grade gold, copper and silver deposit at Phoenix proved elusive, with Battle Mountain Gold being the last company to make an attempt. When Newmont acquired Battle Mountain Gold and its Phoenix reserves in 2001, the lower grade of ore was not a deterrent. Newmont found Nevada-wide cost savings synergies for maximizing profit during the depressed gold market of the late 1990s. The new property was aptly renamed the Phoenix Mine, a nod to its rising from the ashes of the dreams and efforts of previous mine owners.

Jan 2, 2010

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012