Search Documents

By Don U. Deere, Edward J. Cording

INTRODUCTION Observations during construction form an integral part of the design and construction of major underground works. Observations as used herein include visual inspection, detailed geologic mapping, and correlation of geology with support conditions, as well as instrumentation to provide more precise information regarding rock movements and support load. This paper describes the application of an observational program to one of the more difficult design and construction problems underground -- the excavation and support of large chambers at shallow depth in rock of variable quality. Emphasis on underground construction for subways and utilities in urban areas is bringing this problem to increased prominence. It is our intent to focus on the design and construction problems associated with such excavations and to describe observational methods which can be employed to aid in their construction. Observational programs may serve two purposes. One is to monitor the rock and support conditions in order to provide early warning of potential construction problems. Such a program should be routinely used in critical locations on major underground excavations of the type described in this paper. The program should be closely coordinated with the inspection effort and construction control. The other purpose is to provide detailed information regarding the interaction of support conditions and rock displacements to aid in development of more efficient design and construction procedures on later projects. For this purpose, instrumentation might be concentrated in special test sections where specific and typical

Jan 1, 1997

By J. F. T. Agapito, J. B. Page

This paper describes part of a geotechnical study based on stress determinations and convergence measurements conducted to assess the long-term stability of an experimental room-and-pillar oil shale mine. A rock mechanics program was initiated in 1971 at the Colony Mine as part of a large study conducted for the design of a commercial operation. The Colony Development Operation is a joint venture currently consisting of four active members; Ashland Oil Inc., Atlantic Richfield Company (Operator of the project), Shell Oil Company, and The Oil Shale Corporation. Although oil shale commercialization plans are presently suspended, rock mechanics instrumentation has been continued as part of Colony's policy in maintaining readiness to proceed with a commercial shale oil plant when national energy policies became better defined. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 200 miles west of Denver. Experimental mining operations were conducted from 1965 to 1972 with one of the major objectives of the pilot mine being the assessment of opening and pillar sizes for the determination of extraction ratio and life of the property. Mining was conducted in a 60 foot thick portion of the Mahogany Zone in the Parachute Creek Member of the Green River Formation, at depths of 600 to 850 feet by a one-bench system. Pillar dimensions were 58 feet by 58 feet and rooms were 55 feet wide.

Jan 1, 1977

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread-sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin. Computerized search Computerized search approaches represent crude first attempts at letting the computer design the blend. Unfortunately, the blends found by these programs are very often less satisfactory than those developed manually. The way these techniques work is that they design, according to some predesigned pattern, a number of different blends and then quickly evaluate them. It is then straightforward to select the best from this sample set. The quality of the results depends on the number of blends designed, the way they differ from each other (the search procedure), the number of sources available, the number of quality specifications, and the severity of the specification limits. Good results are usually obtained for small, simple problems. At best, the results obtained are inconsistent from one blend to the next. Programs of this type are advertised in the mining literature. They usually mention how many different blends are evaluated, making it clear that this is more than can be tried manually. Expert systems Expert systems use a source of information known as a knowledge base. The knowledge base, usually a set of if-then rules, attempts to reconstruct the deductive reasoning process of an expert in some job capacity. For coal blending, the usual trial-and-error process has an easily recognized pattern of rules that are followed to try to find a better blend. By following these rules, it is possible to home in on the best blend without the exhaustive search required by the previous method and without the manual manipulation of the spreadsheet approach. The use of an expert system accomplishes this. One of the rules may say something like "if BTU is out of spec, then add more in the blend from a source having a high BTU and subtract some from a source having low BTU." In other words, it goes through the trial-and-error process. The process continues until all specifications are achieved and can continue further to try to optimize the cost. Of course, less simplistic rules are also needed. One set of rules would determine maximum changes in the tonnage added or deleted to the blend or from any one source. Other rules would be needed to determine which quality to improve if two or more are out of spec. At this level, the process of building the knowledge base provides the engineer with a deeper understanding of his or her own thought processes. The advantage of obtaining better blends is clear for this approach. Two more advantages should also be apparent. One is that it follows the same common sense logic that is used when doing the blends by hand or by spreadsheet, making it easy to understand. The other is that, like the search procedure, it designs the blend rather than just analyzing manually designed blends. Thus, it has all the good features of both approaches discussed thus far while providing improved results over each. A final advantage is the ease of use and ease of development. The expert system shells that are on the market are very easy to use and can be run on microcomputers. Linear programming Linear programming is an algebraic tool that solves a set of linear equations to yield an optimal solution to a problem. The optimal solution is based on the linear model so the results are only as good as the ability of the linear model to accurately portray the reality of the problem situation. It is fortunate for the coal blending problem that a linear model can be devel¬oped that reflects exactly the problem that is required. Unfortunately, the mining industry has been slow to use this tool. Coal blending applications available that use linear programming take one of three forms. The first, requiring exper-

Jan 12, 1988

By J. W. C. Wong, T. A. Songberg, S. D. Miller, J. J. Jeffery

Natural degradation of cyanide has been widely used by the gold mining industry for removal of CN from cyanidation processing wastes. However, little documented study has addressed the decay and fate of cyanide within residue storage ponds. 'fhis paper describes a study on the cyanide behaviour in a residue storage pond at the Boddington Gold Mine in Western Australia. Depth profile samples were collected from the active residue storage to determine the distribution of CN forms and complexing metals throughout the settled residue.

Jan 1, 1991

By I. M. Eitani, M. Karmis

Ground control presents the most serious problem in underground thick seam mining. In addition to parameters such as depth thickness and inclination of the seam and nature of the coal and the immediate strata, the stress interactions caused by the mining sequence must be carefully evaluated and understood, if safety and productivity objectives are to be fulfilled. In this paper, the most widely-accepted thick seam coal mining methods are reviewed and suggestions are made for future work pertaining to ground control problems.

Jan 1, 1981

By S. Odell

The Bureau of Land Management (BLM) has constructed two biochemical reactor systems (BCRs) to treat mining influenced water from the Forest Queen Mine near Silverton, CO. The bioreactors coupled with a natural wetland provide treatment to the Forest Queen Mine drainage. The central objective of this paper is to review the performance of the bioreactors and wetland treatment system. The bioreactors have been in operation for nine years and along with the natural wetland are still removing a high percentage of the influent metals.

Jan 1, 2010

By Kurt Bryan, O&apos

The crushing and milling of mineral bearing ores can now be accomplished more efficiently through the application of WaterFlush technology. WaterFlush crushing has reduced capital and operating costs for the processing of a lead/zinc ore in South America. Similar benefits can be expected in the processing of other ores. WF cone crushers offer improved performance over conventional cone crushers. Performance improvements include the ability to crush wet and sticky ores, increased reduction ratios and greater production of flakier and finer products.

Jan 1, 1989

By Donald R. East

In the planning and design of mill tailing disposal facilities, the chemical and physical nature of the fine­grained material to be disposed of has to be fully understood in order to create an efficient and safe long­term storage facility. Disposal of tailing has become the single most important source of environmental impact for mining projects and the development of many promising ore bodies has been delayed or even stopped due to problems of facility siting and design under pressure of increasingly stringent regulatory require­ments.

Jan 1, 1992

By James L. Hendrix, Michael R. Straka, Emil B. Milosavljevic, Ljiljana Solujic, Neil P. Gallagher

Analysts that utilize the classical distillation procedures for cyanide analysis are often frustrated by the poor reproducibility and repeatability of these techniques. Capital intensive business decisions and environmental management regulations are exas­perated by the fact that the EPA/ASTM approved cyanide deter­mination methods produce data of questionable quality. Reliable cyanide values are important in monitoring the effec­tiveness of the cyanide detoxification procedures. Efficiency and cost of gold and silver cyanidation recovery can also be improved by precise cyanide monitoring in the process itself.

Jan 1, 1996

By Richard Ladyman, Ken Baxter, G. B. Siddall

The IPS process, developed by Baxter and McAuley, was first applied in Australia in 1984 at Browns Creek in NSW where a small 300kg batch plant was in operation for a number of years. To date a further 14 plants have been installed. While a number of engineering companies have engineered applications of the technology, a majority of the plants constructed to date have been constructed by Como Engineers who have a reference list of 9 installations with batch capacities up to 3.0 t.

Jan 1, 1996

By Tong Deng, Yun Ma

Gold-copper ores have become important gold resources (von Michaelis, 1989), but the gold extraction from such materials posed a challenge due to the detrimental effect of copper species on gold cyanidation. Ammoniacal cyanidation process was rec­ommended (Muir et al., 1989) and practiced (Castello et al., 1992) for gold extraction from the gold ores which contain cop­per at moderate level mostly in form of oxide. This paper pro­vides an example to apply the ammoniacal cyanidation process to processing such a copper bearing gold ore.

Jan 1, 1996

By Clive Wilson, Bruce Hutchison, Daniel N. Adams

Two three-lane highway tunnels, 700 and 2900 m long, make up the driven tunnels portion of Melbourne City Link. Tunnel construction, using design-construct delivery, commenced in May 1996. Construction required excavation through varying rock conditions; temporary support included ground freezing, pipe-spiling, steel sets, and rock bolts. Permanent support for the tunnels required both drained and undrained tunnel cross sections using unreinforced concrete. This paper reviews the construction methods, and highlights some of the not-so-standard designs developed while construction was underway.

Jan 1, 1999

By Moudgil. B. M.

The amount of hydrophobic materials constituting the mineral froth strongly influences the froth viscosity. Higher truth viscosity, on the other hand, can retard the drainage of physically carried over, hydrophobic particles. In phosphate flotation tests, a direct correlation was observed between froth viscosity and recovery, and an inverse correlation existed between froth viscosity and grade. Phosphate flotation tests in the presence of a silica depressant indicated that higher froth viscosity is an effect rather than a cause for the presence of silica particles in the froth.

Jan 1, 1994

By Douglas R. Shaw

The results are discussed herein of laboratory and pilot scale research which has demonstrated some exciting prospects for the exploitation of refractory gold resources by heap leaching. The research examined practical and cost effective methods of chemical; i.e., non-biological, oxidation pretreatment of refrac­ tory old ores to enable successful conventional cyanide heap leachmg. The work has focused on regenerable chemicals, in order to minimize process consumable costs. A nitric acid method has emerged which offers rapid oxidation rates (eg, 0.5 to 6 hours) on ore samples crushed typically to% to ¾-inch. Gold recoveries in simulated heap leaching tests, after nitric acid oxidation of crushed ores, were as high as approximately 80 to over 90%, in contrast, typically, to negligible gold solu­bilities without oxidation. Nitric acid oxidation was effective when applied to several sulfide-bearing refractory gold ores which required either partial or essentially complete sulfide sul­fur conversion for high gold solubilities in cyanide. Ores rich in organic preg-robbing matter also were treated successfully, as were ores which contain significant quantities of acid-consum­ing constituents. Base metals also were recovered with nitric acid oxidation from some of the ores which contain these ele­ments. The work related oxidation and solution diffusion behav­iors and the important physical, textural, and mineralogical characteristics of the different ore types. Conceptual-level feasi­bility studies have defined the principal capital and operating cost components of the nitric acid method, sufficient to allow reliable comparisons with other oxidative technologies.

Jan 1, 1996

By Kevin Phelan, Gary Johnson, Peter Sperring

The vast majority of tailings in the Western Australian Goldfields are deposited in purpose-built storage facilities. At mine-sites with open-pit mining operations there is also the requirement to mine and stack large volumes of waste rock, usually into surface waste dumps. As these dumps have typically 30% of their gross volume present as voids, there is the potential to use this void space for the storage of tailings. The concept of co-disposal is to store the tailings material in the void space of the waste dumps, eliminating the need for a separate tailings storage facility. Dominion Mining Limited have been investigating the possibility of using co-disposal as a means of tailings storage. Laboratory testwork has been used to understand some of the issues associated with the concept, and assist in the design of an on-site demonstration of the concept. Co-disposal offers a number of potential advantages, and despite a number of practical hurdles to overcome, considerable economic and environmental benefits could be realised if this concept can be demonstrated on a commercial scale. The major advantage of such a system is to remove the need to build, operate and rehabilitate a separate tailings storage facility. Rehabilitation can be incremental throughout the mine life as the co-disposal site will be virtually indistinguishable from a current waste dump in both size and form. Other potential advantages include more stable waste dumps, less land area disturbed on the project site, and better water recovery from the tailings.

Jan 1, 1995

By S. Tavani, R. E. Browner, R. Dunne

Lead is used in CIP/CIL circuit to increase the leaching rate of gold from ores. At least four mechanisms have been proposed for the action of lead in gold leaching circuits: (I) precipitation of sulphides as highly insoluble lead sulphides preventing consumption of cyanide and oxygen; (2) su,face reaction on sulphide particles forming an insoluble lead sulphide layer peventing dissolution of those sulphides; ( 3) precipitation of lead sulphide, which undergoes further oxidation to soluble lead sulphate recycling the lead to solution,· ( 4) contact reduction of lead onto the gold szaface which then acts as a secondary oxidising agent. Rotating disc studies using a pure gold disc show that small amounts (5ppm) of sulphide ions are sufficient to significantly reduce the leaching rate of gold. Lead increased the leaching rate at small concentrations but at higher levels decreased the rate of leaching. The detrimental effects of lead were only found for a pure solution when leaching the gold disc. Ores mediate the amount of lead available by ads01ption/reaction, thus, reduced leaching rates from excess lead are not serious even when 500ppm of lead ions are added to the sluny. The detrimental effects of sulphide ions could be countered by lead addition during the leaching process. A penalty, in the form of reduced leaching rate, will occur the longer lead addition is delayed. A time lag was noted between the addition of lead and the increased leaching rate when a large concentration of sulphide ions was present.

Jan 1, 2000

By J. J. K. Daemen, C. Fairhurst

Two aspects of tunnel support design are considered, and for both particular attention is paid to the influence of rock failure around the tunnel on the loads developed on the supports. 1) In general it has not been possible to extend analytical methods for the study of rock failure around tunnels to three dimensions. As a consequence it was not possible to calculate either the influence of the face or the actual sequence of support loading as the face advanced. The finite element method made this extension possible. A simplified analysis of the influence of the face and of the sequence of support installation has been made. The influence of the original stress field and of the rock behaviour on the length of tunnel which can be left unsupported (related to the stand-up time) is shown. The degree to which a 2-dimensional analysis can be used to approximate the final support load is shown to be dependent upon the post-failure behaviour of the rock. 2) Tunnel support design requires a knowledge of the forces and of the -rock displacements which cause stressing and deformation of the support system. A 2-dimensional model incorporating a detailed representation of several support systems, of the rock behaviour in the broken zone and of the interaction between rock and support is given. The model allows the calculation of the stress distribution in the support. The significance of the relative stiffness of support and rock on the stresses developed in the support is shown.

Jan 1, 1997

By S. Ubaldini

Acid mine drainage (AMD) is a common problem in different areas with a past history of mining activities, which is characterized by low pH (2-4.5) and significant toxic metals concentration. The main aim of the present work was to perform a process feasibility analysis in order to remove heavy metals (Cd, Zn, Ni, Mn, Cu) from AMD (Acid Mine Drainage) in a relatively cheap and environmentally friendly way, by means of electrowinning and biosorption. A first characterization of an Italian AMD sample was performed evidencing a zinc concentration around 2 g/L, cadmium and nickel content of about 4 mg/L, manganese of 85 mg/L and iron 190 mg/L. Electrowinning tests lead to the following metal removal after three hours treatment: Zn 99%, Ni 99.9%, Cd 99.9%, Cu 99%, Mn 87%, Fe 96%. Moreover, an high grade of purity of the metal deposit has been achieved (Zn>95%), as observed by X-ray diffraction analysis. Considering that metals concentration in the effluent was still above legal limits (in particular for Zn, Mn and Fe), a further biosorption treatment was planned in order to produce an effluent fitting environmental limits. Experimental electrowinning tests and literature multimetal column biosorption data have been used in order to perform a preliminary techno-economic feasibility analysis of the process aimed at metal removal from AMD. A treatment cost of about 6.5 ?/m3 AMD has been estimated, for a plant capacity of 10 m3/h AMD inlet flow rate.

Jan 1, 2006

By K. L. Kayler

Ball clay production in 1991 amounted to about 800 kt (880,000 st), about the same as in 1990. 1992 estimates show a 5% decrease to 750 kt (827,000 st). This decrease continued a trend of reduced production that began after the peak of 900 kt (1 million st) that occurred in 1988. Use of ball clay in sanitary ware was about 2% less in 1992, although levels of use in floors and wall tile, dinner ware and pottery remained constant. Filler, extender and binder applications continued to be important end uses, accounting for about 17% of total market. Refractory uses maintained their market share of about 17 kt (18,700 st). Use of clay liners in toxic and waste dumps is an application widely found in Germany. However, its use has not been fully exploited in the United States. This could represent an opportunity for domestic clay producers. Tennessee remained the leading source of ball clays. Other producers were Indiana, Kentucky, Mississippi and Texas. Tennessee's production, however, decreased about 3% in tonnage produced and its value dropped from 68% to 65% of total production. The ceramics division of Southern Clay Products, Inc., was bought from LaPorte plc by United Clays of Texas, Inc., a US subsidiary of Watts Blake Bearne & Co. The purchase included ball clay reserves at Troup, TX. The acquisition makes United Clays the second largest ball clay producer in the United Sates. United is also the only company mining clay in Texas. Fire clay production decreased 5%

Jan 1, 1993

By D. C. Willett

INTRODUCTION The Symposium on the Development of Underground Space, held in Seattle, Washington, from October 1 through 3, 1980, was organized by the "Deep Space" subcommittee of the ASCE's Underground Research Technology Council. The primary objective of the symposium was the exploration of the interfaces between the investigation, design and construction of large underground facilities in "deep space" which, for the purposes of the committee, has been defined as starting at 100m below ground surface. The meeting focussed primarily on tunnels, caverns and shafts in hard rock; the meeting format comprised a number of brief presentations concerned with the technical aspects of investigation, design and construction, followed by an open discussion, and concluded with the assembly of recommendations regarding the interface problem by the symposium participants. The principal considerations brought out during the symposium, and a general review of the conclusions, are briefly presented in the following paragraphs. INVESTIGATION The sessions dealing with "Investigation" were chaired by Dr. H. Pratt. Presentations were made by Dr. D.C. Banks, Dr. W.A. Hustrulid and Dr. Pratt. The extent of the interface of the investigation phase with the other (design and construction) phases of an underground facility will depend in large measure upon the nature of the facility; at one end of the spectrum, the investigation must be in continuous and closely coupled relationship with the design of a radwaste facility. At the other end of the spectrum, for (say) a small mining operation, the interface is largely associated with the initial development, with only minor on-going involvement.

Jan 1, 1981