Search Documents

By M. Irish

This paper describes the emergency water control measures used at Pegasus Gold's Zortman Landusky mine during the September 1986 flood. The amount of solution stored increased by approximately 78 165 m3 due to receiving 0.2134 m of rain in a 24 hour period. Three methods of water disposal will be discussed including continuous chlorination, batch chlorination, and reverse osmosis. A water management program will also be discussed.

Jan 1, 1988

By C. Tsatsanifos

Following closure of an old asbestos mine in Zidani, Kozani Prefecture, Greece, the geotechnical and environmental restoration of the tailings slopes was required. The geotechnical aspects of the restoration included the formation of gentler slopes to increase stability, in combination with drainage works for the same purpose. The environmental aspects of the restoration included covering the slopes with successive layers of soil in order to minimize infiltration of rainwater, and hence the potential for further transport of asbestos fibers, and to provide a suitable layer for revegetation of the slope. The paper presents results of slope stability evaluation using both limit equilibrium and finite element analyses and raises some issues related to reducing impacts to the geoenvironment when designing such restoration projects.

Jan 1, 2006

By Doug Williams, Kent J. McGrew, Dr. Jack Murphy

For some time, selenate has eluded water treatment by conven­tional means such as precipitation and clarification. This has been due to the nearly universal solubility of all oxidized sele­nium species, the low levels required for surface discharge, and almost identical chemical behavior to all forms of oxidized sul­fur. The last characteristic makes selenate particularly difficult to deal with in acid mine waters where sulfate can easily be on the order of one gram per liter. Approaches such as ion exchange or reverse osmosis often tum into total demineraliza­tion schemes for the sake of removing a "trace" selenium species that may be present on the order of 108 sulfate/selenate. Reduction of selenate to selenite or elemental selenium by chemical means has been relatively unresearched. Some limit­ed success has been reported (Murphy, 1988) using ferrous hydroxide as a reducing agent; however, the reaction time as reported is too slow to be useful in a practical plant design. One significant difference between selenate and sulfate is that selenate has been discovered to be reducible in acid solution by elemental iron when catalyzed by soluble copper. Since the +4 or zero valence states of selenium are rather easy to deal with by coprecipitation with iron salts or alum, the elemental iron dis­solved in the process contributes to the overall process by pro­viding sludge upon raising the pH that can be separated by con­ventional clarification. Commercial production of selenium using copper catalyzed reduction of selenite to selenium metal via sulfur dioxide is well established, however, at the < 5 ppb requirements for surface discharge this reduction process equili­brates at levels far too high to be useful to low level selenate removal criteria. The reaction reported herein uses elemental iron for reduction of selenate with copper acting either as a cata­lyst or as a coprecipitation agent. This method, employed with conventional sludging, clarification and filtration can provide an economic method to achieve non detectable selenium (< 0.005 mg/I). Iron consumptions for the conditions tested have been on the order of 3 lbs/1,000 gallons treated. This represents as little as $0.06 or $2.00 per 1,000 gallons based on using a scrap source of iron or the purchase of electrolytic iron for the process.

Jan 1, 1996

By R. J. Pindred

In his paper, Davis presents an overview of risk. He also introduces the Capital Asset Processing Model (CAPM) as a foundation for selecting the appropriate discount rate for a mining project. While applying portfolio theory is more defensible than the ad hoc adjustment of discount rates, the CAPM is not a panacea.

Jan 1, 1995

By P. F. Hara, O&apos

Stratabound Proterozoic precious metal mineralization in central Arizona is associated with felsic and adnesitic to mafic volcanic rocks and sediments derived from these rocks. Hydrothermal fluids associated with felsic volcanism form gold mineralization within hotspring vent complexes or within asymetric basins, which flank the vent complexes and are filled with tuffaceous sediments. Massive to semi-massive sulfide copper-zinc systems associated with felsic volcanism may locally contain small gold occurances either laterally or vertically zoned from the ore. In andesitio to mafic rocks, zinc-lead-gold-silver-copper bearing mineralization and gold mineralization are both associated with feruginous sulfide bearing cherts. The partitioning of gold into these specific geologic environments may be related to variations in temperature and composition of the hydrothermal fluid and the depth of the seawater-sediment interface below sea level during the mineralization event.

Jan 1, 1988

By Gordon Hubbard, John D'Acierno

The Randgold Resources Ltd. mine operation in Syama Mali performs whole ore roasting followed by CIL gold recovery to produce gold. The roaster has operated continuously since the plant was first commissioned in 1994. The roaster design throughput is 216 tons per hour (5,184 TPD). Roasting provides for the oxidation of the· refractory components, organic carbon and sulfides. The energy balance for the system requires auxiliary fuel oil to be burned in the Circulating Fluid Bed (CFB) reactor. Energy from the 1200-1350 degree F roasted product stream is recovered and recycled back into the CFB using two fluidized bed coolers; one to directly heat the secondary air and the other to indirectly heat the primary fluidizing air. The basis of the design for the roaster was an extensive pilot plant test program, the results of which were scaled up to the full scale plant design. Due to variation in the feed at the mine a number of roaster modifications were necessary following the initial plant start up. During 1998 ore flotation capability was added to reduce the operating cost for the roaster and increase plant throughput.

Jan 1, 1999

By George S. Koch

Today, after about 30 years of development, computer-based analysis of geoscience data has reached a mature phase. From the tentative early beginnings recorded in the proceedings of the APCOM meetings, geoscientists are now able to emphasize the need for both pertinent mathematical/statistical models and computer hardware and software. From those models that are well understood in the disciplines of statistics and mathematics and for which effective computational methods are available, practitioners select and develop methodology for their particular purposes. Computer hardware is typically assembled from off-the- shelf components now readily available, with particular emphasis, whenever feasible, on microcomputers for reasons of economy and control by the scientific or engineering user rather than by a bureaucratic computer center. Computer software may be written by the user in high level languages such as Pascal, FORTRAN, or LISP. However, more often today geoscientists use routines available in spreadsheets, data bases, or statistical packages. In so doing, they save time and, programming costs and take advantage of routines written and maintained by large, well- established organizations, while losing the flexibility in specifying exact input/output afforded by writing in a high level language.

Jan 1, 1989

By C. Bazin, B. Girard

The application of time series analysis techniques to plant data provides a method for examining and modeling the behavior of operators during the operation of furnaces for the reduction of ilmenite concentrate. The obtained model is used to assess the consistency of actions carried out by the operators and to review and improve the training procedures.

Jan 1, 1996

By John G. Banker

Titanium/steel clad has been selected as the material of construction for six pressure acid leaching autoclaves for nickel production from laterite ores. These six pressure vessels are now in production service in western Australia. Titanium provides reliable corrosion protection in the nickel laterite pressure leaching environment. Clad metal construction offers a significant cost reduction for equipment of this type in comparison to solid titanium. Clad metal construction offers superior durability and reliability in comparison with non-metal or titanium loose-lined equipment. Experiences in titanium clad equipment construction and performance are reviewed. The presentation addresses aspects of design, fabrication, and testing which are necessary to assure reliable equipment. The explosion cladding proces and titanium alloy selection considerations are also discussed.

Jan 1, 2000

By Michael J. Virnig, Kathryn C. Sole, Murdoch W. MacKenzie, Michael R. Davis

A solvent-extraction process has been developed for the removal of copper cyanide complexes from aqueous copper/gold cyanide solutions formed in gold-recovery circuits that treat ores containing cyanide-soluble copper. The process uses LIX® 7820, one of the LIX® 7800 reagent series developed by Henkel. It is based on a mixture of Aliquat® 336, a quaternary amine, modified with an alkylphenol, 4--nonylphenol. Extraction and stripping data for the base metal cyanides and thiocyanate are presented. Methods for the recove1y of copper and cyanide from the upgraded strip liquor are reviewed. A flowsheet based on this chemistry and a preliminary economic evaluation of a solvent-extraction circuit combined with the cyanide-recovery process developed by Metallgesellschaft Natural Resources (MNR) are also presented.

Jan 1, 1999

By S. Duyvesteyn, L. Enloe, P. A. Schmitz, W. P. Johnson

The characteristics of gold leaching from carbonaceous matter by sodium cyanide, and sorption of gold cyanide to carbonaceous matter in autoclaved and non-autoclaved gold ore from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was investigated. Much greater gold cyanide complex sorption was observed for the carbonaceous matter in high preg-robbing ores relative to the low preg-robbing ores. This observation corroborates previous reports that have attributed observed preg-robbing behavior to the carbon in the ore. Gold cyanide complex sorption was found to be reversible for carbonaceous matter from low preg-robbing ore, but was irreversible for carbonaceous matter from high preg-robbing ores. Autoclaving the ore appeared to enhance the sorptive behavior of the carbonaceous matter from both high and low preg-robbing ores.

Jan 1, 1999

Magnetic separators are commonly used as an effective and low-cost method to concentrate paramagnetic or ferromagnetic minerals. These versatile separators are often used in multistage circuit configurations to further improve concentrate recovery and/or grade. Although these circuits are generally very efficient, field studies suggest that the layout of multistage circuits can be less than ideal for many industrial operations. To illustrate this shortcoming, a theoretical analysis has been conducted to compare different circuit configurations for magnetic separators. The resulting knowledge base has been used to establish generic engineering guidelines for the layout of multistage circuits. The potential improvements in separation efficiency that may be realized through the application of these guidelines have been demonstrated using a simple case study.

Jan 1, 2004

By M. Khandrika, B. K. Parekh

Column flotation has proven to be the most effective technique for the flotation and recovery of ultrafine coal. The commercial application of columns in the coal industry is steadily increasing (Parekh et al., 1990; Yoon et al., 1992). For the flotation of coal or mineral air is used for generating bubbles. Using a conventional flotation cell, Miller and Mishra (1985) compared froth flotation behavior of fine coal using air, nitrogen and carbon dioxide gas. They concluded that carbon dioxide gas provided a higher rate of recovery and a lower ash content. The objective of the present study was to investigate the effect of various gases such as compressed air, nitrogen, argon, and carbon dioxide on the column flotation of fine coal.

Jan 1, 1999

By R. D. Hendry, R. A. Pearce, Allyn J. Steward, Dennis C. Martin

This paper outlines the geotechnical exploration and design approach utilized for the Km 80 and Km 86 Tunnels on the British Columbia Railway Tumbler Ridge Branchline. Information from surface mapping, trenching and diamond drilling was used to prepare a rational support design using accepted rock mass classification systems. Four possible support types were developed and used as a basis for preparing a cost estimate and contract documents for the tunnels. A unit price contract was selected to provide flexibility and to enable rational selection of support based on actual ground conditions encountered during excavation. Although ground conditions along the tunnels are variable, the general geology and quantities of support installed were consistent with those estimated from the geotechnical investigation and design.

Jan 1, 1985

By J. Duncan Wilkins

Introduction In difficult times such as these, there is a strong reaction to the current way of doing things. Typical reactions that we have all heard are "There has to be a better way," "We&apos;re pricing ourselves out of business," "We have to improve our productivity," and "We have to have more cooperation," between union and management and employees and management. All of these comments have at their roots one common factor - getting the maximum amount for your dollar. The other factor inherent in these statements is productivity. I have not yet met a person in our industry who has not expressed the opinion that we should, and that we can, improve our productivity. Reducing Labor Costs In light of these factors I suspect we have all spent a fair amount of time examining our labor costs. For some of us, labor costs are a high proportion of our total cost of doing business. To alleviate the impact of these costs, we have generally done four things. We have reduced our number of employees, shut down operations for appropriate periods, sought concessions from union employees, and placed freezes on wages, salaries, and other benefits on nonunion employees. These approaches have been made to improve current shortfalls in our cash positions - to tide us over, as it were - or to provide us with a chance for survival. These are short-term measures that help to bring immediate relief, but can pose significant problems (or challenges), for the longer term. For instance, what do we do when times improve? How much do things have to improve before we do anything? By seeking concessions from unions in bad times, what do we do when unions come to us in good times? It is a rather sad and critical fact that we have grown too fat during the good times and too thin during the bad. In the first case, we have failed to optimize our earnings. In the second, we have cut ourselves too far. Consequently, when good or better times have arrived, we have had to bulk up our requirements to meet production commitments. In mining, for example, when times become tough, we tend to reduce our development plans so that when times improve we have to really "sock it to &apos;em," so that we can maintain productive capacities. We should plan ahead a little more to reduce the amplitude of our cyclical wavelength, so that in good times profits are optimized and in bad time we are better able to take the strain. Of course, forecasting cycles is not a refined art, but if we properly control our work force levels and costs at all times, and therefore optimize our productivity, we would be more able to withstand the problems we face today. Unfortunately, it appears that it takes bad times to bring us to a realistic appraisal of our way of managing our businesses. Labor Practices Not all of the problems now faced are due to low metal prices. Inflation has played a major role in bringing costs to a frightening level. Trade unions alone can not be blamed for high inflation levels over the past several years, popular though that notion is. Contract negotiations, after all, require two parties. Indeed, our current levels of labor cost are due to two factors: • We have felt obliged to keep our employees whole, relative to the cost of living. • We have felt obliged to maintain our competitive position relative to our peers, in order to maintain our ability to attract and retain a skilled, efficient work force. In the first case, our felt obligation has been applied without due recognition of the factor of performance, either in individuals or groups. Average, even mediocre performers, have been amply rewarded for their average work and mediocrity, while the good performers, no doubt receiving more for their good work and effort, have not perhaps appreciated the slight premium for their effectiveness. The rather predictable result of this practice has been that the average and mediocre stay that way (why change?), while some (certainly not all) of the good performers have said "It&apos;s not worth it," and slipped into the warm, cosy pool of the average and mediocre. In the second case, that of maintaining competitiveness with other companies&apos; employees, we have compounded an already serious problem of lack of skilled tradesmen by paying higher and higher prices for the existing pool to maintain comparability without improving the flow of more skilled people through sound and sufficient training programs. We have the rather dubious pleasure of paying more and more for the same problems. Compensation is either mutually agreed, as with unions, or it is unilaterally applied, as with nonunion employees. Generally, there is more flexibility available to the employer when dealing with nonunionized groups than there is with unionized groups. Sometimes that flexibility has not been used well, most often be-

Jan 11, 1983

In general, it cannot be assumed that the strength of coal pillars remains constant over long periods of time. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing the load-bearing capacity of the pillars. This paper discusses a unique approach to determining the time-dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15, and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar, and the strength profiles were determined for each hole using a borehole penetrometer. The strength data were treated statistically to establish time-dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 2012

By C. Anderson, K. Nikkhah

This paper outlines the role of simulation software in design and operation of a typical metallurgical plant with mineral processing and hydrometallurgical units, to produce concentrate and pure metal. It addresses the role of simulation and mass balance software in the conceptual, feasibility and detailed design stages. It discusses the use of JKSimMet for sizing of mineral processing units, and METSIM and IDEAS for development of energy and mass balances. In detailed design of a plant, the complex interaction and variation in performance of various units makes it difficult to predict overall system performance and availability. Simulation is used to: assess operating strategies that affect surge capacities at various stages compare different ore types and mining strategies that affect concentrate product quality. optimize transportation logistics for raw materials, concentrate and metal products

Jan 1, 2001

By Ross R. Bhappu

In 1989, William A. Vogely created the Mineral Economics and Management Society (MEMS). He did this after SME disbanded the Minerals Resource Management Committee, a group dedicated to technical programming of minerals economics and management issues. A few years later, SME reinstated this committee. MEMS held its fourth annual conference "Mineral resources: Managing dilemmas and opportunities," in Boulder, CO March 9-11, 1995. Some of the MEMS programs are similar to the Minerals Resource Management Committee programs. However, MEMS conferences cover more diverse issues. These include minerals policy, environmental legislation impacts on the minerals industry and minerals economics issues. The 1995 MEMS conference included six sessions and three distinguished speaker addresses. Papers topics included US and Canadian mineral policy, financial strategies for managing mining companies, Latin American mineral investment opportunities, quantitative economic modeling and the impact of environmental interest groups on the minerals sector in the United States and Canada. One session was dedicated to students who competed for $1900 in prizes for outstanding papers.

Jan 1, 1995

By R. V. Ramani

It is common knowledge that there is an endless stream of possibilities, proposals, and projects - each representing a demand on available capital - for improving the mining company&apos;s performance measure. It is true that these proposals go through an increasingly stringent evaluation process as they move up the echelons of management for approval. Therefore, there is every reason to expect that a proposal or project accepted for deployment will make a substantial contribution to the organization&apos;s performance. The reality, too often, is otherwise. Castle (1985) reveals some significant insights into the difficulties in predicting the performances in the mining industry. A sample of eighteen mining ventures, which have been developed over the years, was selected by Castle to illustrate the problems. The actual performances were compared with the original projection. The sample encompasses both surface and underground mines, a large number of commodities, and a wide geographic distribution. The experiences in these mining projects were analyzed through answers to four specific questions.

Jan 1, 1989

By Charles S. Phillips

Kaiser Aluminum and Chemical Corp. (KACC) had been discharging spent bauxite-generally referred to as red mud-into the Mississippi River for almost 20 years when, in 1972, it agreed to store the waste solids on land. KACC decided to utilize a DREW system (decantation, drainage, and evaporation of water) where the spent bauxite is deposited in a large drying bed, surrounded by a 9-m-high levee. At the bottom of the bed, corrugated, perforated plastic pipe is encased in filter sand. The company built one DREW bed at Gramercy, LA, in 1973 and a second at Baton Rouge in 1974 using draglines, tractors, and rubber-tired scrapers. When a third bed was needed in 1977, the estimated construction cost using draglines was judged too high and KACC personnel began searching for a better, less expensive method for constructing the levee. A bucket-wheel excavator and conveyor system was selected and has proved to be less costly than more traditional earth-moving systems.

Jan 7, 1980