Search Documents

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By C. R. Euston, B. T. Field, W. E. Lindquist

Pyroprocessing applications in the minerals industry range from low-temperature drying to high-temperature reactions. Material characteristics and process requirements range over a very broad spectrum and can confuse plant engineers trying to select a pyroprocessirtg system for their plant. This paper examines the important process variables and offers empirical guidelines to assist in a user's overall process evaluation.

Jan 1, 2000

By John R. Marks

The recent trend in the ventilation of deep under- ground metal mines in the United States is to rely more and more on refrigeration for air cooling. This paper describes the layout and the economics of the refrigeration method used by Hecla Mining Company at the Star Mine. An economic analysis must compare the benefits of an engineering system against the costs. The benefits of refrigeration, for example, are increased production rates, a better safety record, improved employee moral, and generally lower airflow requirements. Air-conditioning costs include capital expenditures for equipment, labor and supply costs for maintenance, and power costs for machine operation. A study of whether or not to install refrigeration becomes academic when a mine reaches the critical ventilation depth1 (the depth at which adiabatic compression alone produces station temperatures equal to the desired stope temperatures). Ventilation planning alternatives for such mines, including the Star Mine, are limited to the different methods of refrigeration usage. In this case study of the Star Mine, the refrigeration layout is described in detail. After the system performance is discussed, air-conditioning costs are calculated. The paper then concludes with a cost- benefit analysis of the Star Mine refrigeration system.

Jan 1, 1980

By C. E. Jordan, B. J. Scheiner

The Bureau of Mines conducted research on the flotation hydrodynamics of fine particle flotation to improve the flotation efficiency in our domestic minerals industry. The turbulent fluid velocity profile was measured in various flotation cells at different levels of dissipation energy. The importance of dissipation energy and bubble size within the flotation cells for the flotation response of a chalcopyrite ore was evaluated. Both increased turbulent fluid flow and fine size bubbles improved the flotation rate of fine size chalcopyrite particles.

Jan 1, 1989

By R. D. Willette

The Hector Mine deposit in the California Mojave Desert has a magnesium-rich clay that formed when lithium and fluorine were introduced into isolated fine lacustrine volcanic sediment during the Pliocene. The intensely deformed deposit has been supplying the highest grade thixotropic clay to the coatings industry for over half a century. A thixotropic clay displays the property of changing from a gel to a sol when shaken, and increases in strength upon standing.

Jan 1, 1995

By Takashi Sakaguchi, Takehiko Tsuruta, Akira Nakajima

Some attempts were made to recover gold from aqueous systems using immobilized persimmon tannin. This adsorbent adsorbed gold from solutions containing hydrogen tetrachloroaurate (III) with high efficiency, whereas there was minimal adsorption from solutions containing gold (I) sodium thiomalate and sodium dicyanoaurate (I). The adsorption of gold was rapid, and was affected by the pH of the solution, temperature, external gold concentration and amount of adsorbent. Adsorbed gold was easily desorbed with 1 M thiourea solution, indicating that immobilized persimmon tannin can be repeatedly re-used for the recovery of gold using adsorption-desorption cycles.

Jan 1, 1995

By Lawrence A. Ph. D. Hansen, J. David Deatherage

Laboratory testing programs were conducted to investigate the performance under compression loading of several types of geomembranes and geotextiles proposed for use in heap and dump leach projects. Synthetic liners of several thicknesses were sandwiched between representative subgrade soils and cover materials, thus modeling in the laboratory the actual installation conditions expected. Performance was evaluated by visual inspection and vacuum testing. Several testing procedures and equipment were used to investigate the effect of these testing parameters on the predicted performance.

Jan 1, 1987

By W. A. Rickelton, A. J. Robertson

The ability of triisobutylphosphine sulfides to selectively recover silver from acidic sulfate solutions containing zinc and copper is described. Selectivity is explained in terms of the concept of hard and son Lewis acids and bases. Silver is stripped from the solvent using a novel strip feed (thiosulfate salt), and the recovery of metallic silver from the strip liquor by electrolysis or cementation is suggested. The high selectivity of extraction for silver and the utility of the stripping reagent are demonstrated in continuous, countercurrent, mini-plant tests. Important reagent properties, such as hydrolytic stability and low aqueous solubility, are discussed.

Jan 1, 1988

By Y. Ye, J. D. Miller, E. Pacquet, S. Gopalakrishnan

From laboratory research activities during the past five years, it is now evident that effective flotation separations can be achieved with the high-capacity air-sparged hydrocyclone. The effectiveness of the equipment has been demonstrated on a pilot-scale basis (1 tph) for a number of mineral commodities including coal, copper, gold, and industrial minerals using a nominal 5-cm x 50-cm system with separation efficiencies equivalent to those achieved by conventional flotation machines. The high specific capacity of the air-sparged hydrocyclone (100 to 600 tpd per cubic foot of cell volume for a nominal 5 cm x 50 cm system compared to 1 to 2 tpd per cubic foot of cell volume for conventional columns and mechanical machines) makes it especially well-suited for the pro- cessing of low-grade ore. As a result of these pilot-scale successes, a number of plant-scale test programs are planned for larger-diameter units to establish wear characteristics and scale-up relationships for design purposes. The status of the air-sparged hydrocyclone technology is reviewed in the present paper, including a description of the system, fundamental considerations of flotation mechanisms, general discussion regarding the effect of control variables, and the significance of feed characteristics.

Jan 1, 1988

By Charles D. Litton

This Bureau of Mines paper describes a novel fire detector that can be used to discriminate between smoke produced by a fire and smoke produced by a diesel engine. The detector uses a pyrolysis technique whereby a sample of smoke- laden gas passes through a short, heated tube within which fire smoke particles pyrolyze and increase their number concentration and decrease their average size, while diesel smoke particles are unaffected. The detector is designed for use in mines that use diesel-powered equipment where the detection of fires is complicated because of the diesel emissions background levels of smoke and other products of combustion.

Jan 1, 1989

By S. L. Huang, J. D. Rockaway, N. B. Aughenbaugh

Shale has long been recognized for its tendency to swell when exposed to the atmosphere. Interaction of moisture with exposed shale strata can cause serious ground stabi1ity problems, since the initial strength of a shale is reduced if the material is sensitive to moisture variations. In this paper, the authors present a classification system to estimate the response of swelling generated within shales. This characterization of the swelling potential is based upon plasticity, susceptibility to moisture, mineralogical constituents of clay size particles, and fabric. Use of this classification system in conjunction with other existing rock properties tests will provide data for more rational engineering design.

Jan 1, 1986

By S. K. Kawatra, M. T. Rusesky, T. C. Eisele

An on-line monitoring system for apparent slurry viscosity has been developed at Michigan Technological University. It utilizes a vibrating sphere viscometer in conjunction with a special slurry presentation system to reduce particle settling and turbulence effects. It has proven to give accurate, reproducible results in an on-line hydrocyclone installation. Its performance shows that it can be an effective instrument on an industrial scale, particularly in grinding circuits. Development of the sensor and the importance of rheology in grinding are also discussed.

Jan 1, 1992

By T. Brady, J. Johnson, J. Whyatt, B. Pariseau, M. Stahl

An elastic-viscoplastic material model allows for time- dependent rock mass motion in proportion to excess stress above the elastic limit. The model produces rounded stair-step curves of displacement vs. time that are similar to those obtained from recent borehole extensometer measurements made in the central portion of the Ross Shaft pillar at the Homestake mine. The work in progress, including two- and three-dimensional finite element analyses using the UTAH2/3 codes, indicates that the model is a step towards more realistic safety and stability analysis, but that inclusion of rock mass damage may be desirable.

Jan 1, 2000

By M. C. Williams

The dynamic behavior of batch mill, CSTR mill, and a closed grinding network consisting of a mill, sump, and cyclone was analyzed using the dynamic population balance model (PBM). The dynamic solution of the PBM of a batch, CSTR and a closed grinding network consisting of a mill, sump, and cyclone forms the basis of the dynamic analysis presented here. Two numerical dynamic solution approaches were used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data was used to obtain the functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Different dynamic solutions were obtained depending on the numerical approach used. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By M. K. Pathak, A. K. Mukhopadhyay, D. C. Panigrahi

Changes in machinery operating and design parameters often result in unexpected vibrations or changes in the vibration patterns. Vibration in a system is an undesirable element that can cause machinery distress. Potential damage can be prevented by identifying the vibration level that is due to the changed operational parameters. This is necessary for the safe and reliable operation of plant equipment. This paper presents a documented study on vibration events that resulted from alterations in operating and design parameters in a mine ventilation fan and analyzes the causes by defining the sequence of events that led to its performance deficiency. This paper is based on experimental effort to study the vibration behavior of a ventilation fan under varying operating conditions.

Jan 1, 1999

By D. Malhotra

Gold and silver ores are generally leached in weak cyanide solutions for recovery of precious metals. However, pretreatment of refractory ores requires flotation to concentrate the precious- metal minerals. Also, flotation is a common concentration technique for recovering precious metals as byproducts in sulfide-mineral flotation circuits. The present paper reviews current plant practice and future challenges for precious metal recovery.

Jan 1, 1999

By G. Plenge, M. Diaz

Silver-bearing, bulk sulfide concentrates from several Peruvian mines were autoclaved in a l9-L (5gal) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates, following a hot lime jarosite destruction step, extracted more than 98% of the silver and more than 95% of the gold. Autoclave operating parameters, such as time, temperature, pulp density and autoclaved solids recycle, were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to provide reliable scale-up data for a 50 to 100 t/d (55 to 110 stpd) facility.

Jan 1, 1994

By Mark Gershon

This paper describes a linear programming (LP) application that schedules mining operations in an optimal manner. The model is developed such that it can be applied to a broad spectrum of mining activities. While linear programming has been applied to mine scheduling in the past, the models have been either site-specific or they have only optimized one aspect of mine operations without regard to others. The Mine Scheduling Optimization (MSO) concept makes use of a mathematical model to: (1) Determine the optimal operation of a mine, from mine to plant to market. (2) Account for mine-plant-market interfaces. (3) Optimize operations over the life of the mine. (4) Accomplish long, intermediate, and short range planning.

Jan 1, 1982

By F. M. Doyle, S. M. El-Raghy, M. F. El-Demerdash, E. Peters

The Activity Distribution Diagrams (ADD) developed by the authors are computed for Cu-S-H2O and Mo-S-H2O systems. The distributions of metal and sulfur between all species are estimated against pH at different potential levels. Both M-H2O and S-H2O distributions are compared to the M-S-H2O distributions to estimate the changes occurring due to the presence of sulfur. The method of computation follows the Activity Term Criterion, taking into consideration the multi-equilibrium interrelations and conservation of mass. Results are analyzed in terms of dividing a distribution curve into three basic segments. These segments are formation, stability, and dissolution.

Jan 1, 1993

By A. A. Kornyshev, M. Burstein, S. T. Hall

The surface "roughness" of mineral particles has long been known to influence the fundamental process of particle-bubble attachment and other subprocesses in froth flotation. The physical nature of the surface of fine mineral particles can be analysed by determining their fractal geometry. A number of techniques are available to measure the fractal properties of mineral particles, these include gas adsorption, mercury porosimetry, neutron or X- ray scattering and image analysis. From the resultant Richardson plots or their Fourier-space analogs, the fractal dimension of flotation feed and product samples can be determined. Textural characteristics of particles have an influence on the stability of 3-phase flotation froths and the selectivity of recovery in the froth. Decrease of the equilibrium froth height for particles of higher fractal dimensions was experimentally established. The induction time of quartz particles of different fractal geometry has also been studied.

Jan 1, 1995