Search Documents

By Harold B. Goldman

On the basis of tonnage, the sand and gravel industry is the second largest nonfuel mineral industry in the United States. In 1990, the production of sand and gravel was 927 Mt valued at $3.4 billion. California, which leads the nation with more than 126 Mt, together with Texas, Washington, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 Sieve (0.074 mm openings) to those passing a No. 4 Sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see chapter on Industrial Sand and Sandstone and Glass Raw Materials). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material that is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Sand and gravel is also used as construction fill, road base and subbase, and decorative material. Portland Cement Concrete Aggregates: Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15 to 20% water, 7 to 14% cement, and66 to 78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman and Reining, 1983). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate: Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.076 mm), uniformly coated and mixed with asphalt produced in the refining of petroleum. Sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement aggregate. GEOLOGY General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles that are sound and durable. Soundness and durability are terms used to denote the ability of aggregates to retain a uniform physical and chemical state over a long period of time so as not to disintegrate when exposed to weathering and other destructive processes. Individual particles must be tough and firm, possessing the strength to resist physical stresses and chemical and physical changes, that may cause swelling, cracking, softening, and leaching. The aggregate should not be contaminated by excessive clayey material, silt, mica, organic matter, chemical salts, and surface coatings. Physical Properties: The quality of aggregate depends upon its physical and chemical properties. These, in turn, may be inherent mineralogical and textural features of the rock or may be the effects of later changes such as tectonics, mechanical or chemical weathering, or incrustations. The physical properties most significant for concrete use are: 1) abundance and nature of fractures and pores, 2) particle shape and surface texture, and 3) volume changes which may occur because of freezing and thawing or wetting and drying. An aggregate is considered to be physically sound if it is adequately strong and capable of resisting the agencies of weathering without disruption or decomposition. Minerals or rock particles that are physically weak, extremely water absorptive, and easily cleavable are susceptible to breakdown. The use of such materials in concrete reduces strength or leads to early deterioration by promoting weak bond between cement and aggregate, or by inducing cracking, spalling, or popouts. Severely weathered, soft, micaceous, or porous materials may cause localized stresses to develop in concrete by swelling and shrinking during wetting and drying or freezing and thawing cycles. Physical Suitability of the Various Rock Types. Sedimentary rocks have a wide range in physical and chemical qualities. Sand- stones and limestones, if hard and dense, are ordinarily satisfactory, but many sandstones are friable and excessively porous and commonly are clay-bearing. Shales generally make poor aggregate material, being soft, weak, and absorptive. Most igneous rocks are satisfactory, being normally hard, tough, and dense. Tuffs and certain flow rocks may be extremely porous and have high water absorption and low strength. Metamorphic rocks differ in character. Most quartzites are massive, tough, and dense. Fine-grained marbles are usually durable, but coarse-grained marbles have low abrasion resistance. Gneisses are ordinarily very tough and durable. Some schists contain micaceous minerals that are undesirable because they are soft, laminated, and absorptive. Micaceous minerals are susceptible to splitting along cleavage planes and thereby impair particle strength and durability. Some schists and slates in particular are thinly laminated and tend to assume flat slabby shapes that lack strength-and do not pack well. Any or all of these rock types may be rendered undesirable because of harmful exterior coatings. Weathering processes, particularly the action of ground waters, deposit these coatings. The most common coatings are calcium carbonate, clay, silt, opal, chalcedony, iron oxide, manganese oxide, and gypsum. Particles with these coatings are undesirable as aggregates because the bond between particle and coating may be weak, and decreasing the strength of the aggregate-cement bond.

Jan 1, 1994

By M. R. Paterson, M. K. Suddaby

Operational and economic factors tend to favor the application of continuous processes in preference to batch processes in the majority of mineral processing applications. In this paper, the requirement for a continuous elution process is established and the development of a large-scale pilot plant is described. It is based on a continuous elution apparatus that has a number of special features. These are the subject of various patent applications. The apparatus is suitable for adaptation to the AARL, Zadra, and other methods of elution. The performance of the atmospheric continuous elution system (ACE) is concluded to have significant advantages over the batch process.

Jan 1, 1988

By W. H. McDonald, D. D. Carr

The use of stone in building construction predates written history. From the time that stone was first used, builders have constructed stone buildings predominately from local or regional materials. However, since World War II, the stone business has become increasingly global. For example, French limestone is now sold to builders in the United States, and American granite is shipped to Japan. The internationalization of architectural and construction firms has encouraged this trend. Differences among nations in trade practices, environmental demands and the level of knowledge of dimension-stone characteristics make international trading in stone a risky and potentially disastrous business for unwary participants.

Jan 1, 1997

By G. D. Elliot, R. L. Grayson, G. L. Winn

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate was approximately 10 times higher than the national coal-industry fatality rate. Although the number of fatalities went down from 22 in 1991 to 17 in 1992, West Virginia still led the nation in coal-mining fatalities. A team of mining and safety professionals from West Virginia, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training, studied this problem. A clear path for formal intervention was determined and is presented here.

Jan 1, 1996

By J. L. Gent

Compressed air distribution networks are essential for powering equipment in many mines even though some mines are replacing them with electrical power for hydraulic drills. Compressed air can be costly especially if the system is poorly designed and maintained. This paper outlines a technique for proper compressed air system design that will help mine managers reduce compressed air power costs; an important topic in today's highly competitive international minerals market. Compressed air system design is complex. It requires specifying: 1) air quantity and pressure in all branches of a large network, 2) proper location and types of valves and fittings, 3) the network solution that determines compressor requirements, 4) optimal hose and pipe, diameters, 5) receiver and compressor accessories, and 6) required capital and operating costs.

Jan 1, 1989

By R. Bruno

The problem of testing different production strategies has been studied in relation to reserves selection and a computer programme for ore production management has been developed. The case study presented concerns an underground rock salt mine in Sicily with different product lines and variable ore characteristics. A geostatistical block model of the deposit was constructed on the basis of the physical and chemical parameters that ultimately determine the type of end-product in operations according to different selection strategies were simulated using the model and taking account of both technical and 'commercial constraints. The structure of an ore production management programme running on a PC to select both the mining unit and the end-use of the ore is described.

Jan 1, 1989

By R. L. Neman

Southern Oklahoma (including the Arbuckle Mountains) has outcrops of rocks representing Precambrian, Paleozoic, and Cretaceous ages. Thus, rocks of every geologic age in the Paleozoic and Mesozoic Eras, except the Jurassic and Triassic Periods, are present in south-central Oklahoma. With rocks of such an enormous age range present in a relatively small geographic area, it is little wonder that a wide variety of economic rock and mineral resources are locally present. This report will describe the occurrence, mining, processing, and end-uses (dictated by chemical and physical properties) of the Precambrian Troy Granite, the Cambrian Royer Dolomite and Fort Sill Limestone, Ordovician silica sands of the Simpson Group, Ordovician limestones of the Viola Springs and Welling Formations, and Ordovician Sylvan Shale. In general, the more the end-use depends upon chemical composition and purity, the greater the price that can be demanded for such-minerals. The not-so-successful attempts to mine zinc, manganese, copper, and iron from the Arbuckle Mountains also will be discussed briefly, and I will provide a sermonette on analytical chemistry and its usefulness to corporate CEOs. I may be one of the few persons at this Forum on the Geology of Industrial Minerals who is not a professional geologist. I am an analytical chemist specializing in geochemistry. In particular, I investigate trace elements in rocks and their consequences in industrial processes. As such, I have consulted to the mining industry (and their clients) for two decades, always with the intent of improving service and product quality.

Jan 1, 1999

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbonate gangue from sedimentary apatites (francolite) in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to benepciate a high- MgO siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for car- bonate removal and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the MgO was rejected in the froth. The phosphate flotation stage produced concentrates analyzing about 31% P2O5 0.7% ? 5 MgO, and 4% insol. The overall P2O5 recovery In the two stages was about 85%

Jan 1, 1991

By David K. Parrish, Duane A. Labreche

Analyses of jointed, cracked, and fractured rock masses are needed in a variety of applications, including estimates of reduced elastic modulus for damaged rock, estimates of permeability changes as a function of stress changes, and estimates of relaxed regions due to excavation. A numerical model of a jointed rock mass, the compliant joint model, was used to study the response of a jointed rock mass near a circular excavation. The joint constitutive model was linear elastic in shear and nonlinear elastic in the relationship between normal stress and joint closure. Initial stresses were geostatic and representative of stresses in a granitic jointed rock mass approximately 300 m deep. The joint properties were based on values that are representative of joints in granite. The results from numerical simulations were compared with analytical results for stress near a circular opening in an elastic medium having reduced Young's Moduli to simulate jointing effects on the rock mass. The differences in response between the two models resulted from the differences in the symmetry of elastic properties, the shear modulus of the continua, and the constitutive relations in the two models. For example, the non- linear anisotropic elastic continuum described by the compliant joint model resulted in vertical stress concentrations near the side of the circular opening that were 25 percent higher than the vertical stress concentrations in an isotropic linear elastic medium. The equivalent Young's Moduli in the vertical and horizontal directions of the compliant joint continuum deviated by as much as 50 percent from the values assigned to the modeled region prior to excavations. The perturbations of the elastic Young's Moduli extended to distances of two to three radii from the opening.

Jan 1, 1986

By A. S. Ibrado, D. W. Fuerstenau

The adsorption of the cyano complexes of Ag(I). Cu(l), Hg(II), Cd(II), and Zn(II) on activated carbon was investigated as a function of pH and correlated with the speciation diagram for each metal. The results show marked changes in uptake with pH, closely resembling the predominance profiles of their neutral and singly charged cyano complexes. Multicharged negative complexes are repelledby the negatively charged carbon surface. The sensitivity of activated carbon to the charge of the adsorbing species indicates that silver adsorbs as an anion, not chemically bound to the coadsorbing counterions. For the same reason, activated carbon is selective to metals that preferentially form neutral and singly charged cyano complexes, namely gold and silver.

Jan 1, 1990

By R. Fraher

The control of mine roof is of vital interest in underground coal mining not only for reasons of safety, but also to avoid the high costs of cleanup, resupport and production losses that can result from roof falls. The difficulty in determining roof stability mine-wide is due in large part to the broad variation of geologic and structural conditions that typically exist throughout a mining area. To ensure a stable roof over the entire mine, support systems must be selected to minimize the possibility of failure. The magnitude and cost of the support selected is a trade off against the cost of the number of falls that can still occur after it is installed. Because of the large number of variables involved in analyzing and optimizing roof stability versus support, a digital computer simulation was selected to find a cost effective solution to roof support design. A total cost approach is used which includes the actual cost of the roof support as well as the cost of the roof fall in terms of resupport and loss of production (Fraher 1990a). A Monte Carlo simulation program called ROCSIM (Roof control Optimization Cost SIMulation) has been developed for determining the optimum roof control system and design layout for underground room-and-pillar mining.

Jan 1, 1992

By Ishwar G. Mulani

In conveyor design, the first step is capacity and the second step is belt width and speed. The third step is decision on 'ff," where distinction arises between DIN/ISO and CEMA for calculating resistances. Then again, both the methods are virtually similar. This topic helps in understanding Dm design style and its comparison to CEMA. This topic is from the book Engineering Science and Application Design for Belt Conveyor wherein the issue has been analysed in detail. It presents a workable calculation model to calculate the value off in design office, based on conveyor parameters. CEMA uses Kx, Ky and 0.01 5 instead off. Thus, f is a sum effect of Kx, Ky and 0.015. Hence, knowledge on f is also applicable to Kx and Ky. This helps to understand their relationship.

Jan 1, 2004

By F. C. Schwerer, C. R. McKee, J. C. Seccombe

Production of methane from coal seams requires hydrofracturing, and the length of a hydraulic fracture determines we11 spacing. Since the volume of fluid injected is known, the fracture length is the volume divided by average width and height. If the fracture is contained in the known height of the seam, then fracture width becomes the major factor con- trolling length. Width is proportional to coal compressibility; bulk compressibility is known to be larger than intrinsic compressibility. A method is given here to measure in-situ compressibility (a) from transient pressure testing. Theory linking flow in porous media with rock mechanical properties is reviewed. A consistent derivation of the porous flow equation is given incorporating 3-D deformation and the effective stress parameter "st' linking changes in effective stress and pore pressure. The relations for "st' in terms of a and intrinsic compressibility (ai) are substituted into the field measured porosity-compressibility product (net) and solved for a, the constrained matrix compressibility. In a field example, using 4 wells with an anisotropic analysis, the ratio of major to minor permeability was 17 for the Pratt A seam. a was found to be 6x10-5/psi as opposed to the laboratory value of 1.4x10-6/psi.

Jan 1, 1986

By B. J. Arnold, C. D. Harrison, R. A. Lohnes

More than 544 Mt (600 million st) of coal are handled annually for use by this country's coal fired power plants. Coal is transported in various ways: overland conveyors, railcars, trucks and barges. It can travel short distances or thousands of miles, picking up moisture, freezing or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise. To ensure that power plant availability is not jeopardized by coal handling problems, the Electric Power Research Institute's (EPRI) Coal Quality Development Center (CQDC) developed a research program aimed at addressing utility coal handling problems. The program has identified key areas, and is investigating the cost and cause of coal handling problems as well as the solutions to these problems. The ultimate goal of the program is to develop a "handleability index" that utilities can use in their coal specifications or hardware for a utility's sampling system to predict handleability and determine if a coal shipment should be accepted.

Jan 1, 1993

By Joseph M. Denk, Gary J. Wirth

This paper summarizes a three phase face ventilation study which was conducted from September 1989 through March 1990 to determine face area methane liberation patterns on two extended longwall sections. The coal seam being mined was considered gassy and the mine liberated an average of 14.4 million cubic feet per day (cfd) or 0.41 million cubic meters per day (cmd) of methane through the mine fans. The mine also used an extensive underground degasification program to recover up to 13.4 million cfd (0.38 million cmd) of methane. Data was collected while the longwall sections were mining from the beginning, middle and end of panel extraction to determine the relationship between the methane liberation and extent of longwall retreat. As expected, methane concentrations did increase from the headgate (intake) to the tailgate (return) side of the longwall face and peak concentrations were detected above the shearer as it passed a methanometer location during mining. There were significant differences in the methane liberations due to the location of the active face within the longwall panel. Results from this study could be used to determine a minimum design face air quantity for an extended longwall section operating under similar conditions.

Jan 1, 1991

By Al. Valero

This paper quantifies in universal units (energy units), the annual decrease in the mineral endowment of the planet. This is done for some important extracted non-fuel minerals, namely aluminium, cobalt, chromium, copper, gold, lead, uranium and zinc and is compared with the depletion figures of conventional fossil fuels. The results of this study reveal that each year, the decrease of the global non-fuel mineral bonus provided by Nature is 2 to 3 orders of magnitude greater than the loss associated to the burning of fossil fuels. Particularly for 2008, the depletion in mineral wealth of the studied commodities was about 20 times greater than that of fossil fuels. The assessment methodology is based on the Second Law of Thermodynamics. It quantifies the useful energy (exergy) required to concentrate a mineral from a completely dispersed state in the crust, to the conditions of composition and concentration found in the mines. Exergy can be a useful measure for quantifying the mineral depletion caused by man, as it takes into account the main physical features that make minerals valuable: composition and concentration. This analysis enhances and puts numbers to the importance and necessity of material reuse and recycling.

Jan 1, 2011

By Eric Forssberg, Ming-wei Gao

Four parameters of the Drais stirred ball mitt, i.e., bead load, bead size, flow rate and top feed size have been studied regarding their influence on the specific surface area. A factorially designed scheme was employed for conducting 27 mitting tests. The results show that the bead toad is the most important parameter in terms of increasing the specific surface area with less energy consumption. The bead size is also important. The optimum ratio of bead size to top feed size is found to be 14 to 80, which is much wider than in bat2 milling. The variations in flow rate and top feed size appear to influence the process insignificantly.

Jan 1, 1992

By Louise H. Michaud

An interactive mine planning system that employs recent advances in 3D computer graphics capabilities and 3D geologic modelling to aid with the tasks involved in producing dragline mine plans was developed. As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans. The package incorporates the generation of a three dimensional Gridded Seam Model (GSM) as the basis for the development of the geologic database. This modelling method is capable of accurately representing rugged topography and multiple coal seams, including folding and faulting. The GSM is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal resources and the movement of spoil material. The gridded structure of the model also provides the foundation on which all mine and spoil pile volumes are calculated.

Jan 1, 1992

By B. Pollack, L. G. Stevens

INTRODUCTION In other chapters of this volume many of the important technical aspects in the design of concentration and dewatering circuits have been discussed. This chapter will deal with the steps necessary to bring that information together in order to produce the specifications necessary to purchase the equipment and complete the design. It deals with the plant as a whole rather than just concentration and dewatering, since the steps are essentially the same. Prerequisites to Engineering Design Feasibility studies will have been completed and design parameters established prior to the start of the engineering design stages for a metallurgical plant. The data base for the feasibility studies will have included laboratory and/or pilot plant test work, historical data, proposed plant site data such as climatology, topographic mapping, geological and geotechnical information. These studies will have established the general project design criteria as well as the process design criteria leading to the preparation of preliminary flowsheet ( s) and/or alternative process flowsheets. These will have incorporated metallurgical and material balances, allowing identification of major equipment items, and development of preliminary plant site plot plans. Preliminary technical and economic assessments and recommendations will have been prepared during this phase for Owner's review and evaluation of the technical, physical, and cost effectiveness of the overall project and its component process, process facilities, and supporting facilities elements. After Ownert s approval and decision to proceed, the engineering design can be initiated, using the above information as the basis. Engineering Design Phase The engineering design of metallurgical plants and their elements are generally developed in two sequential stages, namely: (1) Basic ("Front end") Engineering Design (2) Detail Engineering Design Figure 1 relates these engineering stages to the entire program from feasibility through construction.

Jan 1, 1986

By P. Sotiropoulos

In the framework of the Specific Programme: ?Promoting Competitive and Sustainable Growth? a detection system was designed and developed in order to provide an added value service beyond standard instrumentation. In the hydrocarbon industry it will be possible for the first time to detect in a pulse regime, two types of radiation emissions using a single device. This means that any saturation of hydrocarbons can be detected, irrespective of the degree of formation water mineralization, which is a major limitation on currently available neutron-gamma tools, where the formation water has a low mineralization.

Jan 1, 2006