Search Documents

By R. Bruce Thorndycraft

Heap leaching should not be chosen for development of a property solely on the basis of paper studies. Management should be made to understand where the risks are in heap leaching, and management should be alerted to the variability of costs in heap leaching, many of which are based upon company philosophy. These concepts are complex, but easily illustrated with guided tours of existing heap leach facilities.

Jan 1, 1998

By P. Aparicio

The rheological properties of five kaolins, isostatically pressurized at 4 x10 Pa for 10 min in the presence/absence of water, was determined. Under dry conditions, measured viscosity values either decreased or remained the same. After treatment under wet conditions, measured viscosity values were 30-60% higher at high shear and 50-60% higher at low shear. These results correlate with variations in nanomorphology and structural order. Dry compaction degraded kaolinite crystals but wet-pressing appeared to cause an increase in the proportion of euhedral crystallites and a decrease in deformed crystals. Dry compaction decreased the low-defect phase proportion (ldp), but in contrast, the ldp in wet-treated kaolins remained constant or increased. Results show that hydrous pressure treatment produces a change in viscosity of kaolin suspensions, yielding the potential for improving paper coating performance, whereas anhydrous pressure treatment decreased or maintained the viscosity.

Jan 1, 2010

By Howard L. Hartman

Introduction The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry, too, is affected by the drought. Research is lagging. Hardpressed universities are going to the private sector for funding. Mining companies should not shower universities with philanthropy, but a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that could be adopted by the mining industry. An equal partnership arrangement between a university and an industry for conducting research is proposed. The concept is not that a corporation sponsors and a university performs the research. Nor does it call for educational contributions or giveaways from industry. Rather, the corporation and the educational institution enter into a cooperative research endeavor, a full and equal partnership. Both parties contribute and both share the benefits. A key to the relationship is that it has a single objective: it must generate profits or reduce costs for the company. Working Model Recent literature is replete with examples of proposals for joint research endeavors, involving both contracts and grants, between industry and universities (Bronwell, 1971; Bugliarello, 1978; Branscomb, 1981; Sanford and Holland, 1982). They are all good proposals and offer something to both parties. They are, however, not widely supported. Few have received a favorable nod from the US mining industry. Though it may be logical, for example, to remake the American Mining Congress (or some new consortium) in the mold of umbrella-type industry organizations to fund cooperative research with mining institutions, such proposals have never flown. What model, then, will work? First, look for a model that has worked in industry in general. Second, seek to apply it to mining specifically. There is a model project that satisfies the first of those criteria. It is a project complicated by a third party, in addition to a corporation and a university. In January 1983, the "Factory of the Future Project" was initiated between The University of Alabama (UA) and General Motors Corp. (GM). The United Auto Workers (UAW) is a third party to the agreement. The factory was GM's Rochester Products Division manufacturing plant in Tuscaloosa, AL, also home of UA's main campus (Fig. 1). Saving a Plant The agreement came about at the initiative of GM and the UAW. Faced with having to close the plant because of excessive production costs, company and union officials proposed to the university that an applied research facility be established at the plant. The university would operate the laboratory, dedicated to $470,000 a year cost reductions for the company. The school would lease the 5.1 km2 (55,000 sq ft) space for $470,000 a year for three years. Any savings effected by the university's research effort would be credited toward to the rent. GM said the small factory, which made replacement carburetors

Jan 9, 1984

By Sharanappa Yalal, Rakesh Kumar Khali

"Himalayan geology poses the most challenging ground conditions almost anywhere in the world, one of the reasons thereof is their evolution as the youngest mountain chains. They are demonstratively rising faster than any mountain elsewhere. The composition is also younger, and consequently less well consolidated than the other older fold belts. This is consistent with the fact that they constitute one of the most active of the plate margin zones rising at a rate that is almost double the Andes, which is in turn three times that of the Alps. Thus, stress conditions (Magnitude and variations) can potentially be more extreme and adverse on a Himalayan tunneling project. Tunnel excavation under the Himalayan Mountains will pose significantly more challenges than an equal length and equal cover drive almost anywhere in the world. These in-depth-tunneling difficulties through high mountainous terrains have posed major challenges for application of traditional drill and blast (D&B) and NATM methods. Handling such adverse geology at any depth is always problematic and generally leads, if not adequately foreseen, to the significant tunneling delays. The author wants to highlight the challenges faced and on the spot solutions adopted while executing most prestigious 273Km long Udhampur –Srinagar- Baramula Rail Link Project (USBRL) in the Himalayas in the state of Jammu & Kashmir, India. The main focus of the paper is on main stretch of USBRL Project i.e. T-80 (India’s 2nd longest railway tunnel & 3rd longest in Asia) where the team of the author has recently completed a 11.2 Km long tunnel and where the train track has gone operational from Qazigund to Banihal. The construction of this stretch posed several challenges akin to highly adverse geological conditions. Executing on -the -spot solutions, the project has been completed successfully. 1.0 INTRODUCTION Construction of Udhampur-Srinagar-Baramulla Broad gauge railway line is one of the Mega projects undertaken by Indian Railways to establish a dependable transportation in the state of Jammu and Kashmir. In engineering terminology, it is a challenging project negotiating breakthroughs against the complex Himalayan geology. The Project which has been operational over last 12 years , stretch by stretch, is in advance stage of construction . The purpose of the prestigious project is to connect the Kashmir valley to the mainland of the state of the country. On the date owing to the hurdles of the tuff terrain, the transport of this part is totally dependent on the surface transport, i.e., through a road which connects NH-1A from Delhi to Srinagar. The altitude of the region varies from 500.00 to 1700.00, ranging through Udhampur to Katra - Reasi –Sangaldan- Banihal-Quazikund-Ananthnag-Srinagar-and Baramulla. The main features of this project are its Pirpanjal Tunnel and T-48 & 49 tunnels which cover the maximum length of tunneling through thick hostile geological conditions, the total length being 138km. Details of Pirpanjal tunnels are shown in Figure-1."

Jan 1, 2016

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By P. Oghazi

It is possible to have traceability in the mining industry, by parameters and signatures like particle mineralogy, mineral association, texture and mineral liberation. The study is on an apatite-iron ore deposit at Malmberget, Sweden, and characterizes an ore body both mineralogically and texturally in a quantitative manner by using analytical methods like optical microscopy, microprobe (EMPA) and an automatic SEM based system, Particle Texture Analysis (PTA). The mineralogy was evaluated by PTA and characterized by modal mineralogy, mineral liberation and mineral associations. Magnetite has a simple outline and straight grain boundaries and the gangue minerals have a finer particle size with a more complicated texture. The PTA analysis also shows that apatite is associated to magnetite as mixed particles, while smaller grains of magnetite are inclusions in feldspar. Result from particle texture analysis shows that there is a connection which link to the mine-to-mill context, and it may be used to create traceability. This link is not the associations of the main ore mineral magnetite, nor the modal mineralogy. Instead, it is the mineral associations of contaminating minerals (apatite and feldspar) that appear to be most promising since they survive from mine to mill. The modal mineralogy may be used to understand how contaminated minerals break into or out of particles size fraction during grinding.

Jan 1, 2010

By V. Kontogianni

The underground extraction of coal is associated with ground movements extending from the mining area to the ground surface, which result in bowls of ground subsidence, with amplitude exceeding the amount of several meters and occasionally with important tilt and curvature of ground surface. Such changes at both the underground environment and surface topography lead to destruction of buildings, failure of utilities and transportation networks, and occasionally formation of areas vulnerable to flooding, or even small pools. Based on geodetic surface measurements of ground elevation changes, various theories and empirical models relating surface subsidence with the geometry of underground voids formed have been proposed, and predictions of expected subsidence in the form of contours have been estimated. In this study a case study of planning of a new highway network through areas in which coal extraction was also planned is discussed. This work is partly funded by EU. The optimum solution selected was a modification of the initial highway planning, so that the road is increased in length and by-passes the richest coal-field, where maximum post-exploitation subsidence was predicted, and only crosses either minor coalfields, which are not to be exploited, or even margins of main coalfields, in which minor post-exploitation subsidence is expected.

Jan 1, 2006

By John Litz

The term "refractory gold ores" refers to a wide number of ore types which are not readily amenable to direct cyanidation. A number of processes have been used commercially, and a number of others have been proposed and in many cases pilot tested. The selection of the appropriate process for an ore should not be arbitrary. Ore grade may preclude some processes, but a good understanding of the ore mineralogy can guide the selection. Many present gold operations and many potential gold operations have faced or are facing problems with refractory gold mineralization. We at Hazen Research have had the opportunity to perform bench testwork and in some cases, pilot plant testing on a number of refractory ores. The data included in this paper are excerpted from the testing of fifteen ores which cover a wide range of mineralogical compositions. This paper is not intended to be a treatise on the processing of refractory gold ores. In many of these gold projects, not all of the standard process alternatives were evaluated, nor was adequate mineralogical work performed. Such is the dilemma of contract research. "If I believe that I don't need it, why should I pay to have it done." The intent of this presentation, therefore, is to show how different ores respond to the various processes, and to demonstrate that one must have an open mind when developing a process for a specific refractory gold ore.

Jan 1, 1998

By Kazmierczak J. B., Klein E., Kinscher J., Lizeur A., De Santis F.

In this work, we propose to implement machine learning methods for the automatic classification of mining-related seismic data. The approach retained for the classification is based on a Convolutional Neural Network (CNN) which has been tested and applied to two different mining datasets: the active ore mine of Garpenberg (Sweden), currently under exploitation, and the abandoned coal mine of Gardanne (France), where mining stopped in 2003. The first step of the approach consists in creating a well classified (manually) database of seismic signals separated in different classes as a function of the seismic sources. The selected database is then divided into two groups: train, containing the 70% of the signals, and test, which contains the remaining 30% of the signals within the selected database. The learning phase of the algorithm consists in creating a classification model based on the train group, which is further validated on the test group. The application of CNN for the automatic classification of Garpenberg and Gardanne seismic data shows, respectively, that about 88% and 98% of the seismic events of the two sites can be properly classified. These results demonstrate that machine learning could be a powerful tool for microseismic monitoring in mining and post-mining environments, which could be further extended to the whole automatic processing of seismic data, including signal’s classification as well as microseismic event’s localization.

Apr 26, 2022

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By Wilhelm J. Kogelmann

The concept and operation of novel shaft sinking systems utilizing roadheader-type cutter booms, including mucking, conveying, and hoisting installations, are described. Selection criteria, performance data, and economic considerations for various shaft excavators are presented. Various applications of this low-cost and flexible system for civil engineering and mining projects will be discussed. The cutter booms can work in both soft ground and competent rock. Furthermore, the novel excavator can operate in ground stabilized by grouting, cementing, and freezing. The flexible cutting system can be used both for excavation of shafts, foundation pits, slopes, and for tunneling (drifting).

Jan 1, 1989

By Theodore H. Budd, Douglas J. Heinz

This report concerns the successful construction of Contract No. 287 of the Northeast Side Relief Sewer System for the Metropolitan Sewerage District of the County of Milwaukee. The contract involved the construction of approximately 3316 meters (10,880 feet) of tunnel concrete lined to 1.83 meters (72 inch) internal diameter; 30.48 meters (100 feet) of 1.83 meters (72 inch) reinforced concrete pipe jacked-in-place; a river crossing of approximately 107 meters (350 feet); 197 meters (647 feet) of 1.83 meters (72 inch) reinforced concrete pipe in open-cut; several diversion and flow monitoring structures; and miscellaneous manholes and appurtenances. The contract proposal, which was extremely prescriptive, did allow alternative methods of primary support consisting of precast reinforced concrete segments, steel liner plates, steel ribs with wood lagging, and combinations thereof in designated areas. The specifications required the contractor to designate which support scheme it intended to use. The specifications also required compressed air as a means of ground water control for approximately 2316 meters (7600 feet) of tunnel. The alternative selected in the bid proposal was the support method consisting of steel ribs and wood lagging for 2263 meters (7425 feet) of tunnel and steel liner plates for the remaining section. Shaft supports, by specification, were designed to be steel liner plate with steel ribs varying in size from 4.27 meters to 6.10 meters (14 foot O.D. to 20 foot O.D. ).

Jan 1, 1983

By Michael Michaylov

INTRODUCTUCTICN The coal seams at Bobov dol basin are highly prone to spontaneous combustion in Bulgaria. The risks of endogenous fires (SPONCOM) exist mainly in gob area. During the last 15 years three different technologies for preventing and fighting SPONCOM have been applied in underground mines of this basin: pulp from hard material and water, foam and inerting with nitrogen. On the basis of experimental application of these technologies as well as theoretical and experimental research a new technology - Foam Pulp Technology (FPT) was worked out. It is very effective in difficult to reach places in a gob. BACKGROUND AND THE NEED OF FPT Application of the three methods mentioned above showed advantages as well as some disadvantages, allowing determination of their effective application scope depending on geological and working conditions. Their advantages can be summarized as follows: - Foaming: high viscosity at low density, which allows forming a thick layer; good surfactant wetting properties; excellent effective cooling during evaporation in high temperature zones. - Pulping with mixture of solid particles (e.g., fly ash) and water from surface installation: easy to apply in a mine; low operational and energy costs due to gravity transport from the surface to the gob: good ecological results because the waste material is returned back underground. - Inerting with nitrogen: volumetric action which doesn't restrict the thickness of treated coal pile; easy to apply in a mine; controllable nitrogen delivery depending on fire hazard conditions. Main disadvantages of the same three methods are: - Foaming: rapid disintegration due to intrusion into heterogeneous and porous media and high costs due to the need of frequent large volume foam flows (short foam's life); - Pulping: inapplicable for coal piles with high thickness which is of great importance in the cases of seams with ununiform hypsometry (rapid and frequent changes in a seam configuration) and/or great volumes of coal or ore piles particularly heated to a high temperature; strong dependence on gob floor declination; water draining of the working face area which impedes the movement of supports and chain conveyor's. - Inerting: relatively high costs hardly depending on the rate of face advance (fig.1) in comparison with the other methods; it is difficult to ensure sufficient oxygen at the exit end of the face. This problem is crucial in faces with a high level of methane emissions; accelerating of the oxidation and spontaneous heating of the pile after turning off the nitrogen supply. Inerting should be applied again at higher capacity of nitrogen supply (fig.2) and what is more important, it shouldn't be

Jan 1, 1995

By James W. Guider

Of all the technology available to the iron blast furnace operator, raw materials preparation is by far the most important. Superior raw materials have been basic to the success of the Japanese steel industry, and they are just as essential to the American steel industry in winning its competitive battle against foreign government subsidized steel imports. Therefore, the mine operator and the ore beneficiation engineer must strive to produce the highest quality raw materials possible to meet the precise demands of the modern blast furnace and steel plant.

Jan 1, 1978

By Peiwei Xiao, Xiang Li, Biao Li, Haoyu Mao, Nuwen Xu

As an advanced method of rock engineering construction safety monitoring, microseismic monitoring technology can monitor the micro-fracture of rock masses within an effective range, and then perform forecast analysis of rockburst, cracking, falling blocks and other disasters. Although the application of microseismic monitoring technology has become more mature, how to improve its application efficiency remains to be further studied. At present, artificial intelligence has been extensively developed, and the use of intelligent algorithms to improve the efficiency of rockburst forecast can provide a valuable reference for the safe construction of underground engineering. To this end, this paper proposes a microseismic multi-parameter rockburst early warning model based on dynamic Bayesian networks. First, the sensitivity of microseismic source parameters to rockburst forecast is analyzed based on microseismic monitoring data and actual rockburst information of a hydropower station. Second, the main seismic source parameters and their data are selected and imported into a dynamic Bayesian network for learning to obtain the rockburst forecast model. The model is confirmed in its self-validation and K times cross-validation, and the receiver operating characteristic curve of the model is also analyzed, it is found that the area under the curve is close to 1, indicating that the model has good accuracy. Finally, the analysis of the influence strength of the parent and child nodes in the model reveals that the moment magnitude and source scale are the most sensitive parameters, which can be used as an important reference for rockburst forecast.

Apr 26, 2022

INTRODUCTION The role of comminution and related unit operations in mineral processing applications is of major importance. This is especially true in terms of operating costs, since these unit operations represent the major fraction of the overall processing costs. Due to the broad scope and the large number of unit processes and machines involved, Section 3 is divided into five subsections. In Section 3A, General Aspects of Comminution, topics covered include history, terminology, particle¬size distributions, classes of comminution machines, testing and calcu¬lation procedures, and simulation and modeling. In Section 3B, Crush¬ing. the subjects include jaw crushers, gyratory crushers, cone crushers, hammermills, and impactors. The chapters of Section 3C, Grinding, cover aspects common to tumbling mills, ball mills, rod mills, autogenous mills, pebble mills, roller mills, fluid energy mills, other types of grinding machines, and grinding costs. Section 3D, Classification, coverage includes classification theory, hydrocyclones, and mechanical classifiers, and in Section 3E, Screening, the topics presented are classes of screens, selection of vibrating screens, sieve bend screens, and screening media. About five years after the Handbook was begun, Section 3 was unfortunately without an editor or contributors for over half of the chapters. A committee was then organized to expedite completion of the section. When this committee contacted the persons who had agreed to contribute to the section, it was found that many of them wished to resign from their earlier voluntary obligation to AIME. Therefore the committee had to find new contributors for these chap¬ters in addition to other chapters in Section 3. Since there had been no previous effort to locate contributors for Air Classification, Dust Collection, and Washing and Scrubbing, it was agreed to delete these subsections. In Section 3, equipment availability, capacity, and performance data from various manufacturers and users are provided for engineer¬ing use. Selected data from existing installations are also included. The machines that are being used in comminution, classification, and screening are described in detail, and drawings, photographs, and diagrams are presented to supplement the descriptive material. The editors thank and acknowledge the generous effort of the many contributors, some of whom were called upon five or more years after the Handbook was started. It is regretted that Fred C. Bond, who was a member of the committee formed to complete this section, was deceased before the section was finished. During the time that he worked with the committee, he contributed a great deal as an author and councilor.

Jan 1, 1985

By M. J. Blattman

The problem of measuring the amount of rock removed during a given time interval is faced by most milling operations. Many methods have been developed with varying degrees of success, dependent upon the mining method and the availability of usable data. The Rosebud Mine has been in production for nearly two years, employing several techniques to estimate monthly production from underground production stopes. The use of three-dimensional solids generated from survey data has greatly improved the reliability and confidence of monthly production reports. The authors will summarize the methodology currently being utilized at Rosebud.

Jan 1, 1999

By G. J. Allen

Kennecott Copper Corporation's Nevada Mines Division initiated a program to stabilize the inactive portions of the tailings disposal area and perimeter dikes in 1946. To date, approximately 1,000 acres have been stabilized with vegetation and ground cover.

Jan 1, 1978

By Gordon T. Austin

Garnet is the general name for a family of complex silicate minerals having similar physical properties and crystallizing in the isometric (cubic) system. All garnets have the same general chemical formula but vary greatly in chemical composition. The name garnet is derived from the Latin word granatus, meaning like a grain, which refers to the mode of occurrence wherein crystals resemble grains or seeds embedded in the matrix. GEOLOGY Mineralogy Chemical Properties: The general formula for garnet is A3B2(SiO4)3, whereas A can be calcium, magnesium, ferrous iron, or manganese, and B can be aluminum. ferric iron, or chromium, or rarely titanium. The formulas and names of common garnet species are: [ ] Almandite and almandite-pyrope solid solution garnets are the best abrasive types, but andradite, grossularite, and pyrope also are used. All species of garnet have been used as gemstones. The structure of garnet consists essentially of isolated SiO, tetrahedra connected by oxygen-cation-oxygen bonds through the distinct A and B group cation sites. Within this structure magnesium, ferrous iron, and manganese easily interchange and substitute for each other in the A cation position, and calcium does so less readily. Additionally, aluminum, femc iron, and chromium substitute for each other to a limited extent in the B cation position. This ability to substitute or exchange ions without changing the crystal structure is called isomorphism, and garnet is one of the finest examples of a isomorphous series. Because of this isomorphism there is complete solid solution between certain garnet species but not between others. Fig. 1 illustrates these solid solution relationships. Some rare species of garnet are known that illustrate the wide range of cation substitution that the garnet crystal structure can accommodate. They include: [ ] These rare species are not of interest for industrial applications, but can be of interest to mineralogists and the gem industry. Physical Properties: Garnet displays the greatest variety of color of any industrial mineral. Garnets have been found in all colors except blue. For example, grossularite can be colorless, white, gray, yellow, yellowish green, various shades of green, brown, pink, reddish, or black. Andradite garnet can be yellow- green, green, greenish brown, orangy yellow, brown, grayish black or black. Pyrope is commonly purplish red, pinkish red, orangy red, crimson, or dark red; and almandite is deep red, brownish red, brownish black or violet-red. Spessartite garnet can be red, reddish orange, orange, yellow-brown, reddish brown, or blackish brown. A few garnets exhibit a color-change phenomenon. They are one color when viewed in natural light and another color when viewed in incandescent light. Because of the great variation in color of garnet within each species and similarities in color between garnets of different species it is recommended that garnet identification not be based on color alone. The Mohs hardness of garnet varies from 6.5 to 9.0. Grossularite and uvarovite have a hardness of 6.5 to 7.5; andradite is 6.5 to 7.0; and pyrope, almandite, and spessartite are 7.0 to 7.5 in hardness. There are reports of almandite having a hardness of between 8.0 and 9.0. As with hardness, the specific gravity of garnet varies considerably. The specific gravity may be as low as 3.2 or as high as 4.3 depending on chemical composition. Garnet crystallizes in the isometric system with rhombic dodecahedra and trapezohedra the most common forms. Crystals also form in combinations of dodecahedra and trapezohedra or either of these in combination with hexoctahedra. Crystals can have cubic or octahedral faces, but these are rare. Under favorable conditions of formation garnet will crystalize in nearly perfect forms that rival study models. Garnet also forms as irregular blebs, grains, knots, or masses, with or without distinguishable crystal faces, and as coarse- or fine-grained granular masses that appear to be totally lacking in crystal form. The fracture of garnet also shows great variation. In some garnets, particularly those that are well crystallized and glassy in appearance, the fracture is subconchoidal to conchoidal. Other, more poorly crystallized garnets exhibit a fracture that can only be described as uneven. Garnet occasionally has an indistinct dodecahedral cleavage. Certain species of garnet from specific locations have a pronounced laminated structure consisting of planes of weakness along which parting takes place. This parting may resemble cleavage, but since it is mechanical and not related to crystal structure it is not true cleavage. The optical properties of garnet are sensitive to even small changes in chemical composition or strain in the crystal structure. For this reason each species does not have a single index of re- fraction (IR) but has a range of 1Rs. Uvarovite in its pure form should have an IR of 1.870, but in nature samples vary from 1.74

Jan 1, 1994

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

This paper describes the scientific data acquisition, data interpretation, and sophisticated 3-dimensional modeling processes of an ongoing gas well stability research program by the National Institute for Occupational Safety and Health (NIOSH). Results from the NIOSH field instrumentation programs and the parallel 3-dimensional numerical modeling programs indicate that overburden depth, overburden geology, surface topographic relief, strata dip of the coal measure rocks, and casing cementing alternatives are the dominant factors affecting longwall-induced subsurface deformations and gas well casing stresses. Topographic relief could produce localized longwall-induced deformations if weak-to-strong rock interfaces are present near the bottom of stream valleys. Strata dip has significant impact on longwall-induced subsurface deformations. Cementing alternatives are found to have significant impacts on longwall-induced deformations and gas well casing stresses.