Search Documents

By Mahesh C. Jha, Frank J. Smit

Column flotation and selective agglomeration are promising advanced physical cleaning processes that can be developed for preparing premium quality coal-water slurry fuel from coal fines. Such a fuel could either replace oil or natural gas in certain industrial and utility boilers or else could be burned in advanced combustors currently under development. These applications require coal cleaned to sulfur and ash contents below 258 g/GJ and 430 - 860 g/GJ (0.6 lb/million Btu and 1 - 2 lb/million Btu), respectively, to meet clean air emission requirements. A highly loaded slurry must be produced in order to avoid derating the boilers, and the total cost of the fuel must be below $2.37/GJ ($2.50/million Btu) in order to penetrate the market by the turn of the century. Achieving these technical and economic goals depend critically on the selection of suitable feed coals. This paper describes the identification and evaluation of 18 coals and final selection of six coals from different regions of the United States as potential feedstock for preparation of premium fuel. The work is being performed under a cost-shared DOE project.

Jan 1, 1995

By Mala R. Ciancia

Planned tunnel projects with advanced geotechnical investigations are more frequently being suspended because of changes in funding, politics, or local priorities. Some of these projects are ultimately canceled, some decelerate and stall, some resume after a short pause, and some restart after being mothballed for several years. The restarted project often differs at least slightly from the predecessor project in terms of alignment and design concept. This paper describes approaches to evaluating the quality and completeness of previous geotechnical investigations for a re-activated project, considering technological advances as well as changes in regulatory requirements, contracting approach, and site conditions which may have taken place in the time since the project was suspended.

Jun 13, 2021

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993

By Frank F. Aplan, Edward C. Dowling, Richard R. Klimpel

Several series of time-instantaneous samples were taken on a cell-by-cell basis in the flotation circuits of the Pinto Valley, AZ copper concentrator. These samples were used to calculate mass flow rates throughout the circuit using standard, deterministic metallurgical formulae and also a variety of more statistically oriented techniques. Because of the magnitude of the errors associated with the individual cell samples, the standard metallurgical formulae are not sufficient. Consequently, it is necessary to utilize some type of statistical technique capable of distributing the individual cell sample errors in such a way so as to provide a physically useful mass balance for the entire circuit. This paper explores the use of linear and least squares programming as one technique to providing credible mass balance calculations. For linear programming this was done by distributing the error using two different criteria involving specific linear programming formulations: least absolute sum minimization (which assumes an underlying double exponential distribution error structure) and minimax (which minimizes the maximum absolute deviation and assumes an underlying rectangular distribution error structure). These results were then compared to the more standard formulation of minimization of the sum of least squares which assumes an underlying normal distribution error structure. The least absolute sum approach was particularly attractive due to its simplicity of use and the ease in which repetitive calculations can be done with no user intervention.

Jan 1, 1990

By Thomas P. Goslin

T e mechanization of industry to reduce labor costs and to improve product quality is affecting he scale industry as it has affected many other industries. With increased emphasis on higher production rates many operators are experiencing difficulty in overcoming production problems where weight is a factor. Unfortunately, the scale industry has not shown the development over the last twenty-five years that other instrument industries have. For centuries the balance scale has been the standard and the workhorse of most weighing operations. In recent years considerable effort has been applied to designs to make balance scales more acceptable to industries employing automatic or semi-automatic processes. For the most part the designers have not attempted to replace the basic scale but toautomate functions of material handling and human judgement. Modern dump scales, for example, will accept material from a conveyor until a preset amount of material is on the scale, At this time the scale turns off the conveyor, dumps the load of material and repeats the operation with any desired timing. These improvements have helped industry. Even the scale observer has been replaced with devices which observe the scale reading and operate on weighed objects according to their weights. In spite of' the application of automation to the material handling, the balance scale has not been completely satisfactory. One reason for this is fairly evident when one considers the construction of the scales. Inherently, they are slow devices because of the inertia of the beams. The beam scale, primarily a static measuring device, is at the best limited to slow dynamic measurements.

Jan 1, 1958

By R. K. Singhal

The underground coal mining systems have kept pace with the developments that have occurred in other types of mining industry. A diversified group of machines with high horsepower motors, built-in microprocessor technology and with numerous options to satisfy the miners need in a varying geological environment are now available. A brief review of this existing technology and its likely status within the next 21 years is presented. Discussed also are some of the on-going advanced developments in electronic mechanization, remote control and automation together with mine wide data monitoring and management systems and facilities to process and transmit data to remote computerized stations.

Jan 1, 1989

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator's training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By Mehmet Mesutoglu, Ihsan Ozkan

This study investigates the feasibility of rock bolting support in an underground coal mine gallery with a thick coal seam. The Ömerler underground coal mine working area, owned by West Lignite Enterprise of Turkish Coal Enterprises, was selected for this purpose. Longwall top coal caving is implemented as the production method in the Ömerler underground coal mine. Field and laboratory studies were conducted to determine rock mass and rock material properties, followed by experimental, empirical and numerical analyses based on the acquired data. The obtained design results were evaluated using a resin-grouted rebar rock bolting (RBR) system and steel arch support (SAS) pilot application areas. The numerical modeling results conducted using the fast Lagrangian analysis of the Continua 3D (FLAC 3D v6.0) program indicated less displacement and secondary stress change in the RBR-supported zone compared to the SAS-supported zone. In situ measurements also demonstrated that RBR provided more successful support to the roof during coal production activities. The findings suggest that RBR is a more effective solution when evaluating the feasibility of rock bolting support systems in underground galleries with thick coal seams at the Ömerler Mine. This study emphasizes the importance of more sustainable and safe support systems to enhance operational efficiency in the coal mining industry.

Mar 1, 2025

By R. L. Miller

The potential for recovery of enriched uranium from spent nuclear fuel which has been consolidated into a nuclear waste form was explored in the studies reported here. The waste form of interest is iron-enriched basalt (IEB)--a silicate-based, fused-cast ceramic. IEB samples were prepared containing fuel assembly materials that simulate the core debris of Three Mile Island Unit II;1,2 the nominal composition of the consolidated waste form is given in Table 1. Ore Types The IEB samples, or man-made uranium ores (MMUO), are in two different mineralogical forms. Each MU0 was made by melting the constituent materials and holding at about 1500°C for 1 h. The MMUOs were then heat treated to control crystallization and crystal growth and then cooled to room temperature.

Jan 1, 1983

By P. C. Rath, K. Srinivasa Rao, T. Subbaiah

A process for the recovery of nickel from ammoniacal leach liquor through an integrated solvent extraction-electrowinning (SX-EW) flowsheet was tested on a pilot-plant scale. The objectives of the test run were to assess the reproducibility of laboratory-scale data in a large-scale continuous operation and to study the build up of impurities in the system. The pilot-plant test was conducted under operating conditions that were established from the laboratory-scale experiments. Efficiencies of nickel extraction, nickel stripping and ammonia scrubbing were comparable to the laboratory-scale values, whereas the current efficiency during nickel electrolysis was observed to be less than the laboratory-scale values. The electrodeposited nickel contained some cobalt and iron impurities.

Jan 1, 1998

By K. Soucek

Extraction of hard coal reserves, but also of mineral resources in general in the underground coal mines includes in itself many anthropogenic interventions in the earth crust. These interventions are closely associated with the solution of stability problems in the mine and with occupational safety. One of potential applications of such geo-technical interventions in rock mass is the chemical grouting technology. The chemical grouts are very suitable to affect the physical and chemical properties of rock mass. With the present development of chemical grouts, primarily based on polymers, there come into existence new composite materials during the grouting process (the so called geo-composites), which properties significantly differ from the original rock. An important factor, which affects a choice of chemical grouts and at the same time the effectiveness of grouting technology is the resulting properties of geo-composites. The properties of a coal geo-composite differ from the ones of the unmodified coal seam. On the basis of the laboratory geo-mechanical tests, the differences of properties of both material types were found. While the pure coal samples were destroyed very brittle and explosive, the geo-composite samples were making higher level of tenacity and load bearing ability after overstep of material strength. The presented paper discusses the different behaviour of these original and modified coal samples. The X-ray CT scans were used for observation and demonstration of failure evolution in these samples of pure coal and coal geo-composites after compressive loading.

Jan 1, 2006

During the past decade, since the appearance of Popoff's (1966) review of grade tonnage calculations, it has become evident that defining a new method which could be followed step by step by a technician and which would improve reserve estimation was not a simple thing to do. Some concepts have emerged though, and most definitions of ore reserve now require a statement of reliability (USGS, 1975; and Zwarten-dyke, 1976). Exactly how the reliability should be computed is not a straightforward process. It also became apparent that not only was reliability a requirement but that additional questions such as how to predict mining re- serves from geological reserves were to be asked. In fact what became obvious is that specific models have to be designed for each type of mine and for each type of question which is asked. Most methods can be encased within a unique general geostatistical, model, but it takes considerable custom tailoring, and there are still questions that are left unanswered. In this chapter, before giving techniques, we intend to first review what should be required from a grade tonnage calculation done at the exploration stage. If the final objective is still to specify a tonnage and grade, with eventually a reliability, many qualifications have to be made before quoting, and of course, calculating these two numbers. Then the currently avail- able methods will be reviewed and future trends will be shown; finally a few case studies will be given and recommendations about the choice of a model will be made.

Jan 1, 1979

By L. Zhou, D. Bahrami

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time and computer-power consuming, especially for a large-scale mine ventilation network. In this paper, a direct derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the direct derivative method were verified against the results from a traditional method. The direct derivative method has been proved to be reliable and accurate.

Mar 2, 2022

By Norman E. Breslow, John A. Montgomery, Sanford W. Horstman

Reconstruction of historical exposures to silica dust is required in an ongoing cohort mortality study of workers in the diatomaceous earth (DE) industry. However, historical data were collected using three different sampling methods. This study was conducted to derive empirical quantitative relationships from linear regression equations between the three methods: standard impinger, total mass, and respirable mass. Dust from one diatomaceous earth processing plant was sampled simultaneously by all three methods. Results from 61 clusters of the three sampling devices indicate that the phcle size distribution of the dust varies with the two parent products sampled. baghouse product and main product. The relationships between particle counts and respirable mass are: Respirable mass (mg/m3) = 0.064 (mppd) impinger count for baghouse product dust, and respirable mass (mg/m3) = 0.018 (mppcf) impinger count for main product dust. The relationships between particle counts and total mass are: Total mass (mg/m3) = 0.837 (mppcf) impinger count for baghouse product, and total mass (mg/m3) = 1.21 (mppcf) for main product dust. In all four euuations, the intercept did not differ significantly from zero, and the correlation coefficients ranged from 0.90 to 0.95. Results are compared with data from four previously published studies.

Jan 1, 1991

By H. L. Ehrlich

Modes of microbial attack of metal carbonates, metal silicates, metal oxides and metal sulfides are summarized. The current status of microbial redox mechanisms, whereby metals in metal oxides and sulfides are mobilized, is discussed. Opposing theories of a single mode of attack involving interaction with a microbially produced reductant or oxidant in the bulk phase and of dual modes of attack involving a reaction requiring physical contact between microbe and mineral surface on the one hand and microbial production of a reductant or oxidant in the bulk phase that reacts with the mineral on the other hand are considered. No one mode when finally completely unraveled should be expected to fit all cases. Some biochemical, electronmicroscopic and spectrophotometric approaches for elucidation of missing details of different modes are suggested. Key words: Bioleaching, Biobeneficiation, Metal mobilization

Jan 1, 2003

By J. L. Chakravatti

The movement of air from the surface, through the workings and then back to the surface, is the most important consideration in the ventilation design. The purpose of mine ventilation is seen as the maintenance of acceptable atmospheric environments wherever men work or travel underground; and acceptability is related to the risk of harmful biological responses associated with exposure to atmospheric environments in mines. In mine ventilation, a design engineer often has to contend with a number of problems not experienced to the same degree in other industrial situations; i.e. the vast extent of many workings - offering continuously moving work locations; the difficulty of predicting. inflows of contaminants to the airways which contain the micro-environment; and especially, the effect of mining activity within the duct system (e.g. mine roadways) carrying the airflow. Mining of uranium does not differ, in many respects, from the mining of other metals; the ore must be drilled, blasted and transported from the mine. Underground mining proceeds by the continous development and advancement of a network of passages and rooms or stopes from which ore is excavated. As in most mines, rock conditions and ore grades in uranium deposits very from area to area and between different mines. 1 In uranium mining, in addition to eliminating noxious gases from blasting, diesel equipment exhaust, and the control of dust, it is also necessary to dilute and remove radon, the gaseous element in the uranium chain and its decay products. Long term epidemiologic studies of United States uranium miners and that of miners in Czechoslovakia have confirmed that there is an association between excessive ex¬posure to radon daughters and an increased risk of lung cancer. The common practices for controlling these airborne contaminants are: (1) the circulation of large volumes of fresh air from surface to dilute these contaminants to a permissible concentration, and (2) the sealing of worked-out areas to prevent ingress of radon into ventilating air. 2 The sealing of worked-out areas can be easily and effectively accomplished, but the contaminants intro¬duced from the workings may raise the concentrations in the airways despite a good ventilation system and use of the maximum available amount of fresh air. The ventilating air can be strategically filtered to reduce dust and radon daughters to acceptable levels, and reused prior to final discharge. This strategy properly applied, will decrease the air colume requirements in certain marginal areas of the mine and thereby avoid an overall increase in the mine airflow. This is particularly advantageous in the cold climates of Canada, where the incoming fresh air must be heated in the winter months to a comfortable temperature, Thus, an economical and technically feasible air filtration system, strategically placed, can improve the underground mining environment and reduce the overall cost of ventilating the mines. In addition to affording flexibilty to the venti¬lation system, a potential saving of $1,500/m3/s/year would be realized if air is successfully cleaned and reused when compared with the conventional methods of generating an air current. 3 Denison is justly proud of its achievements in the air filtration technology development. This paper limits itself to an examination of the radiation control aspect of the air filtration strategy.

Jan 1, 1980

A Mineração da Trindade (Samitri) is a major Brazilian iron ore producer. Founded in 1939, privately owned Samitri operates six mines with a total production capacity of 14.5 Mt/a (16 million stpy). The mines are located in southeastern Brazil in the state of Minas Gerais. They are operating in the iron ore quadrangle, Brazil's primary iron ore-producing region. In addition to iron ore production, Samitri has the capability to produce 350 kt/a (386,000 stpy) of ferruginous manganese ore from two mines, also located in the iron ore quadrangle. Historically, about 70% of Samitri's production of lump ore, sinter feed and pellet feed is exported. Destinations include Belgium, Luxembourg, France, Germany, Trinidad and Tobago, China, Turkey and the United States. Alegria Mine In September 1989, Samitri started a new processing plant to treat itabirite, a low-grade iron ore. The goal of the plant was to produce sinter feed (coarse fraction) and pellet feed (fine fraction). Primary separation of sinter feed from pellet feed was accomplished with conventional vibrating screens making a 0.4-mm (40-mesh) cut. The screen oversize was stockpiled as sinter feed. The undersize was deslimed with hydrocyclones and upgraded by conventional froth flotation. Resulting pellet feed grades ranged from 3% to 3.5% Si02. A change in pellet feed requirements by Samarco Mineração SA, a Samitri subsidiary, called for Si02 levels below 1 % and increased production levels. Moreover, market demands called for a change in sinter feed size distributions. Unfortunately, lower pellet feed Si02 levels could not be achieved with the existing process. This was because of the presence of 35% +0.15 mm (+100 mesh) in flotation feed. Flowsheet development. Laboratory and pilot-plant studies conducted at Samitri's research facility found that to achieve lower Si02 levels, the +0.15 mm (+100 mesh) in flotation feed must be kept below 5% to 10%.

Jan 1, 1997

By F. L. Wilke

Bong Mining Co. Ltd. in Liberia, West Africa, operates an iron ore open pit some 60 miles northeast of Monrovia. The production is at present about 40,000 t/d (metric tons/day) from which about 18,500 t/d concentrate with 65.5% Fe is produced. The ore waste ratio is about 1: 1.5 to 1:2. The technical layout and the equipment are very similar to those in many modern open-pit operations as described by Jacobs and Thomson (1967). As described by Lersch in detail (1966), the deposit is a very irregular one. The quality of the ore changes within very short distances with regard to both physical conditions (hardness) and chemical properties. Very soft and very hard ore as well as high-grade and low-grade ore are found adjacent to each other. In addition, there are enclosures of sterile rocks. For the purpose of identification and production scheduling, 12 different types of ore are distinguished.

Jan 1, 1979

By W. de Bruijn

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically pre-pared hematite powder evenly doped with 1% by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous thermo-gravimetric and dilatometric analyses were per-formed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process.

Jan 1, 1988

By W. J. Wuest, M. J. DeMarco

The US Bureau of Mines (USBM) recently developed a rock-mass classification system for evaluating the structural competency of bedded roof strata. The system is called the coal-mine roof rating (CMRR), When compiled with the companion Lotus 1-2-3 spreadsheet, CMRR data are a useful tool with applications to longwall gate-road pillar design, safety-hazard mapping and artificial roof-support analysis. This paper gives a review of some applications under actual conditions found in current US mining operations.

Jan 1, 1997