Search Documents

PREFACE During the past year, the Council of the SAIMM undertook a major strategic-planning exercise to review all its current activities, and to redefine its scope and objectives in the light of changing circumstances. The following are the four main concerns that prompted Council to take stock of the situation. (1) Over the past five years, the SAIMM has become heavily involved in a variety of new activities. (There are many examples, of which the expansion in book publications and the establishment of physical metallurgy as a third major discipline with its own colloquia and schools are perhaps the most important.) While these new activities have considerably broadened the SAIMM's scope, they have resulted in a significant increase in the day-to-day workload of the President, Office Bearers, and Council members, and of the secretarial staff based at Kelvin House.

Jan 1, 1986

Hydrometallurgical processing of complex ores and concentrates is becoming increasingly important as the mining and metallurgical industry seeks to exploit mineral deposits that are difficult to treat using conventional mineral processing and pyrometallurgical technologies. Mineral processing is often challenged by the difficulty or inability to separate valuable minerals into marketable concentrates. Hydrometallurgical processing, using selective leaching technology, can often ?chemically beneficiate? such difficult deposits. Pyrometallurgical treatment of base metal concentrates is capital intensive and subject to ever more stringent environmental control. Hydrometallurgical processing is generally lower in capital cost for an equivalent metal production rate and avoids the gas and dust issues associated with pyrometallurgical processing. The possibility of by-product recovery may also increase with hydrometallurgical treatment. Two examples of new technology or flowsheet development for treatment of complex ores and concentrates are used as illustration. These include the El Boleo process of Baja Mining for recovery of copper, cobalt, zinc and manganese from a complex clayey ore and the PLATSOL? process for recovery of copper, nickel, cobalt, platinum, palladium and gold from a bulk sulphide concentrate.

Jan 1, 2009

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11/2 inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219c. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: 1, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

Your Council has pleasure in submitting its report for the year ended 30th June, 1969. COUNCIL The following served as Office Bearers during the year under review: Messrs. R. C. J. Goode (President), J. K. E. Douglas and V. C. Robinson (Vice-Presidents), P. Lambooy (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Members of Council: Messrs R. J. Adamson, M. Barcza, F. P. Bath, Or J. M. Bereza, Or W. Bleloch, Messrs H. Britten, H. E. Cross, A. R. C. Fowler, A. E. Gilfillan, G. W. Holl, Prof D. D. Howat, Or J. P. Hugo, Messrs C. J. Irving, D. M. Jamieson, J. G. Kirchner, Prof J. de V. Lambrechts, Mr C. E. Mavrocordatos, Or J. T. McIntyre, Mr J. A. Nixon, Prof R. P. Plewman, Messrs J. F. Reid, H. Simon, C. G. Sowry, W. T. Stobart and P. W. J. van Rensburg. Ten Council meetings were held during the year with an average attendance of eighteen. FINANCE The annual accounts, which are attached to this report, show an excess of expenditure over income of R2,124, compared with an excess of income over expenditure of R4,218 last year. There are a number of reasons for this substantial change. There was a loss on realization of investments compared with a substantial surplus in recent years. The publication of the Journal once again resulted in a large loss in spite of a generous subvention of R2,000 from the Department of Cultural Affairs and other assistance amounting to R750. The revenue from sales of publications was down considerably. This is a figure which fluctuates considerably from year to year. The secretarial fee was considerably higher than previously. Due to pressure of work it was necessary for the Secretary to relinquish his duties with the Institute of Land Surveyors and, therefore, for this Institute to assume the additional staff costs involved. Finally there was unusual expenditure on the 75th Anniversary celebrations. There was a pleasing increase in revenue from subscriptions, due to the steadily increasing membership, but this was quite inadequate to cover the substantial increases in expenditure and losses in revenue mentioned above. The changes that have been effected in the arrangements for the publication of the Journal have been mentioned elsewhere in this report. It is expected that these will bring about substantial financial benefits in the long term. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of Rl00 and the total fund was therefore increased by this amount to R4,206. The balance sheet indicates that the market value of quoted shares and debentures increased during the year from R8,755 to R13,059, while the Accumulated Funds now amount to R22,567 as against R24,691 last year. MEMBERSHIP Fifty-six Members, fifty-five Associate Members, thirteen Graduates, twenty-two Affiliates and twenty- nine Students were elected during the year. Twelve Members were admitted to Life Membership; seven Associate Members were transferred to the grade of Member; four Graduates and two Students were transferred to the grade of Associate Member; five Students were transferred to the grade of Graduate; three Affiliates were transferred to the grade of Member; five Affiliates were transferred to the grade of Associate Member. Three Members, seven Associate Members, two Graduates, two Affiliates and six Students were removed from the Membership Roll in terms of By-Law 7.7.1. Your Council records with deep regret the death during the year of the following members: E. F. J. Bulman (Member), E. F. Chapin (Member), R. A. H. Flugge-de-Smidt (Hon. Life Member), T. S. Haldane (Member), J. M. Massie (Associate Member), S. W. Page (Student), S. R. Rabson (Member), M. Ramsay (Member), F. Wartenweiler (Hon. Life Member). A comparative statement of the membership as at 30th June, 1969, and the end of the previous year is shown in the following tabulation: 30th June 30th June 1968 1968 Honorary Life Members 12 10 Honorary Members 6 6 Life Members 176 189 Members 488 514 Associate Members 409 448 Graduates 60 68 Affiliates153 155 Students152 162 1,456 1,552 PAPERS AND JOURNAL The Institute is changing the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. In making this change it will conform to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Engineering Institutes. In making these changes the opportunity was taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Presidential Address by Mr R. C. J. Goode and twelve papers which were published in the Journal during the year are listed below: August, 1968: Presidential Address: "The Institute-In retrospect and prospect." September, 1968: "Rotary mill liner practice in the South African gold mining industry," by J. H. French and O. E. Lissner.

By C. Mueller

In many automated mines, multi media video and audio funtionality has to be combined with sensor information or steering commands, which is the idea of a new, PC based integrated and multi media capable control system. The new control system (Multimedia Control - MMC) bases entirely on TCP/IP networking and internet technology. For the first time, this enables the ‘intelligent’ use of video and audio information: pictures and voice sequences may be forwarded on request only, they may be stored if particular events occur (e.g. video black boxes) and sensor signals as well as actions from the automation system can directly be assigned with multi media sequences. MultiMedia Control entirely bases on object oriented software. It uses most modern software technology. As user interface, only a standard web browser is required. This makes the handling of different machines easy. By using mobile web pads, dedicated local operator interfaces are not required any longer. The service staff just connects to the automated equipment by – wireless –LAN to make required adjustments. Customization is easy using an open Application Programming Interface. Software modules may be added to the system without touching or recompiling existing components. The system was prototyped in 2000 using a demo-application. The performance tests showed very positive results both regarding the control system behaviour and the speed/latency timing behaviour of the multi-media information processed. The system now is slightly reshaped to completely meet the final product requirements. It is expected to be available by the end of 2001. Key words: Machine Automation; Control System; Multi Media; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Streaming Video; Quality Assurance; Service; Control Centre.

Sep 1, 2001

By J. Kempken, T. Schreiter, R. Degel, H. Schmieden

After a short summary of the historical milestones of the submerged arc furnace, the paper will highlight different applications and their specific smelting furnace requirements in the non-ferrous area. Additionally, aspects of rectangular furnace design and the features of the copper cooling system for the side wall will be emphasized. Finally a state-of-the-art design tool as well as a new invention to improve slag cleaning technology will be featured, which shows great potentials especially for the PGM and copper related industry. Keywords: submerged arc furnaces, aerro alloys, non-ferrous, copper, slag cleaning, PGM, rectangular furnace, DC technology

Jan 1, 2006

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

By G. M. Brown, B. J. Ebacher, W. G. Koellner

Introduction There is a continual economic push to increase the productivity of mobile material handling equipment used in open pit mines. This includes the largest electrical machines: excavators (draglines and shovels) and haul trucks (Figure 1). Existing DC drive systems used on this type of equipment are a mature technology. They have no further economic potential to accommodate larger equipment be-cause of the high maintenance costs and the trade-off between power, speed and space limitations of their DC traction mo-tors. In recent years the large-scale introduction of AC drives in the rail transportation sector1,and the availability of poworful GTO and IGBT modules have led to the devolopment of compact, powerful, an drugged AC inverter drives specifically adapted to the mining market2,3. The major advantage of AC drives stems from the squirrel cage induction motor which eliminates the DC commutator. This leads directly to higher speed, increased power density, higher reliability, greater efficiency and lower maintenance of the traction motors. In the context of excavators and haul trucks, additional benofits driving the move to AC are (i) increased production rate due to higher machine speed, and power density, (ii) increased reliability and lower cost inverters using 3.3 kV IGBT's, (iii) active front-end (AFE) technology that improves compatibility with the mine power grid and an proved dynamic response,(iv) intelligent converter design that provides increased fault tolerance, (v) contextual maintenance software that facilitates trouble-shooting, and (vi) remote diagnostic capabilities. This paper describes how these and other features of AC drives lead to higher productivity in mining shovels, draglines, and haul trucks. Minimize the cost per ton of material moved The overall goal that drives design and sales of excavators and haul trucks is the constant requirement to reduce the cost per ton of material moved. Whether this involves blasting, loading trucks, or hauling material to the crusher or waste dump, equipment that reduces the cost per ton of material moved contributes to a more profitable operation. An accurate determination of the true cost per ton to move material must consider every aspect of the equipment and the circumstances under which it is used. Procurement and capital costs, fuel, operating, and maintenance costs over the useful life, and eventually the cost of scrapping should all be taken into account to determine the real cost per ton of moving material. We will focus on two broad areas that relate to the equipment itself; factors influencing the amount of material moved (Table I) and factors influencing the cost of material moved (Table II). Emphasis will be given to those elements in the tables that most influence the productivity of excavators and haul trucks due to the application of AC drive technology. Maximize the amount of material moved Maximize production rate he production rate refers to the quantity of material that can be loaded or moved per hour. This generally involves larger, faster, and more powerful equipment that operates more reliably to minimize down-time. AC motors Figure 2 compares the hoist motor speed-torque response of two 77 t (85 short ton) shovels, one AC the other DC. The absence of commutation limits on the AC motors enables the AC shovel to operate with a greater area under the speed-torque curve, resulting in faster lowering speeds and reduced times for the swing to return to the pit. This is especially important for short swing angles where the operator may have to wait for the dipper to lower. Reducing the cycle time by 6 to 8 seconds at the shovel translates into an increase in shovel production of about 20%. Larger equipment The bucket capacity of excavators has increased approximately 100-fold over the last century. Figure 3

Sep 1, 2001

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

Papers and Contributions Since the Institute's inception, it had been our practice until some years ago to meet regularly for discussion of new developments, using as a basis a paper read by one of the members. Usually, the Journal issue containing the paper would have been circulated well before the meeting, giving members plenty of time to absorb it and perhaps to prepare contributions. Discussion was generally lively, often controversial. The author always had an opportunity to reply.

Jan 1, 1991

By H. E. Bartlett

This paper deals with the sampling and mass measurement for ore delivered from a shaft to a processing plant and the contribution of the data from these measurements to the metal balances from shaft deliveries to final metal production. Accurate measurement of the grade and tonnage of run-of-mine ore is important for four main reasons; ? It enables the measurement of the production from different profit centres to within statistically determined confidence limits for daily, monthly, or annual averages. The profit centres could be individual shafts within a mining complex or ore treated on a toll basis ? The monthly production at shaft head is compared to the grades and tonnage determined from underground sampling and mass measurement in terms of a shaft call factor ? The sum of the production from the shafts is the input to concentrators. This input is a major part of the total input into a complex with concentrators, smelters, and refineries. In terms of the Codes of Practice for Metal Accounting the inputs are compared to outputs and inventory changes to assess the efficiencies and unaccounted losses or gains at the various stages in the flow of metal from source to market ? On a daily or daily moving average basis, the grades and tons from shafts are monitored and compared against these quantities from underground measurements. This acts as a control on off-reef mining, dilution, and other factors underground. Accurate measurement of grade of ore at the shaft head has been a challenge because of the large particle size. The conventional wisdom has been that ore can be sampled accurately only after it has been milled to give a slurry that is sampled as feed to a flotation process. However, when the ore fed to a flotation plant comes from multiple sources each source has to be sampled separately. So, relying on the grades determined using the sampling of concentrator input with cross-stream slurry samplers is not an option for determining the grade from an individual shaft. Impala has developed a system for sampling and weighing run-of-mine ore from multiple shafts. The system involves sampling the inputs to the plants using cross-belt (hammer) samplers and weighing the deliveries using in-motion railway weighing systems. Many samples are taken. Individually they have a high variance but, as a consequence of the averaging effect of large numbers and as shown by statistical analysis, the mean results are fit for the purposes of daily grade control for shafts and for monthly accounting of production from individual shafts. In the metal accounting systems at Impala, the measurement of input, including ore and toll-treated material is compared to the output in the form of final metal and tailings losses, as well as any inventory change that takes place, in order to determine a final metal balance from mill feed to product. The calculated inventory is compared to that measured, and the difference, or unaccounted- for metal, is then reported as a percentage of input. The balances obtained over several years yields balances for platinum that are below 1% imbalanced. Keywords metal balancing, platinum mines, AMIRA codes of practice, metal accounting, sampling, run-of-mine ore, statistical analysis.

Jan 1, 2014

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidizing agent. This work shows how the performance of pressure leaching circuits may be improved by optimizing the configuration of autoclaves and the heat removal method. The objective was achieved by creating an autoclave model that combines mass balances, energy balances, and population balances. A base case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity increase options include circuits in which the additional autoclave is added in parallel, in series, and in series with thickening between the two autoclaves. The copper extraction, productivity, and cooling requirements for these options are compared. The series circuit with interstage thickening has the highest extraction and productivity; however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water, and flash recycling. The flash recycle option results in the highest copper extraction, and the quench water option the lowest copper extraction. IntroductionBackgroundCopper sulphide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work.In the pressure leaching process, sulphide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidizing agent, usually oxygen, is required to oxidize sulphide ions to sulphate ions. The oxidation of sulphur to sulphate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2016

By P. J. Petit

The strategic mission of the South African mining industry is to extract the mineral assets in an energy efficient, economical and safe manner. Drilling has received particular attention in the last few years. As the operations move away from the power source, conventional and old drilling technology result in poor penetration rates, increased drilling shift lengths, slow face advances and limited stope efficiencies. The need for an alternate mining method, performed by a skilled workforce, to increase productivity, has led to the development of the electric rock drilling system for in-stope mining operations. The focus of this paper is a systematic evaluation of the electric rock drilling system as a function of production and technical parameters, in the platinum orebody. The particular electrical reticulation system is illustrated. Power usage, problems experienced, and solutions are described. The safe use of the recently developed drill is elaborated upon by describing protection devices. The testing and certification process, for approval by the recognized authorities, are documented. The testing and certification process, for approval by the recognized authorities, are documented. The human factor is also considered. Known detrimental factors of high noise exposure, vibrations levels and oil emissions are reviewed. In conclusion, recommendations on future strategies for the implementation of electric drilling technology within the mining and construction industries, is included.

Jan 1, 2006

By J. Danoczi

South Africa is running out of fresh water and is looking at ways to improve water usage. This report addresses how a diamond mine in Gauteng has improved the utilization of its water resources. In the past, water from the local river was deemed the most suitable to use in the grease recovery plant but subsequent tests on the water from the slimes dam have shows that this water source is in fact more suitable for diamond recovery. Utilizing the slimes dam water provides a more stable water source than the local river while also reducing the impact of the mine on the water resources in the area.

Jan 1, 2008

By K. I. Afewu, L. C. Woollacott

The design of in-pulp adsorption vessels in the gold industry has, for the most part, been seen as a problem involving the suspension of fine particles o ore in a slurry. The need for the vessel to be designed as a mass-transfer contactor has received insufficient attention. The current series of papers addresses this need The previous paper considered the question of the scale dependence of the film transfer coefficient. This paper examines the mixing considerations that are relevant. A review of the literature and an examination of a limited set of data provide some insight into the mixing conditions needed for the dispersion of the particles of adsorbent. The mixing requirements for the suspension of the ore particles are also considered, and conclusions are drawn in regard to the design of mechanically agitated vessels for gold in-pulp adsorption circuits.

Jan 1, 1995

By M. Splaine, W. Davidson, D. C. Atkinson

Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year LP. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efficiency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations. Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system.

PREFACE During the past year, considerable effort was devoted to the implementation of the strategic plan that was adopted by the SAIMM in 1986. Good progress was made in a number of areas, while in others the foundation was laid for future progress. Key Objective of the Institute The key objective of the SAIMM is as follows: To identify the needs of its members and to initiate and give effect to the means whereby the requirements for technology and scientific knowledge of the minerals and metals section of the South African economy are satisfied; and to represent and promote the interests of its members.

Jan 1, 1987

By M. B. Algeo, R. H. A. Plaistowe

A method of forecasting the haulage trucks required for a large open-pit operation is described. Emphasis is placed on the effects of changes in planning and on the complexities of a mining operation that involves many benches and dumping areas.

Jan 1, 1979