Search Documents

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By Hideo Ando, Yuka Satou, Tatsuya Ishitake

Whole-body vibration occurs when the body is supported on a surface which is vibrating. Occupational exposures to whole-body vibration mainly occurs in the transportation industry, but also in association with other industrial process. Epidemiological studies have frequently indicated an elevated health risk for the spine in workers exposed to whole-body vibration. With regarding to train or bus operators, a fall of drivers’ wakefulness level because of fatigue is often pointed out. This decrease in wakefulness results in an increase of the occurrence of accidents. However, a study of how whole-body vibration affects people's level of wakefulness has not been done. To test the hypothesis that exposure to whole-body vibration has a certain effects on level of wakefulness, the change of a subjective wakefulness level and changes of electroencephalogram (EEG) were observed under experimental exposure to short-term whole-body vibration. Methods Subjects are ten healthy male university students, with an average age of 20.7 ± 1.8 years old, and they are all nonsmokers. Using the equipment (CV-300, AKASHI) of whole-body vibration generator, we consider an exposure environment of actual driver work, so that set the frequency and the acceleration level as 10 Hz and 0.6ms-2 r.m.s.. The subjects were exposed to whole-body vibration in the seated position and exposure time was fixed for 12 minutes. Subjective wakefulness level was evaluated using the questionnaire of VASS (Visual Analog Sleepiness Scale) and KSS (The Kwansei Gakuin Sleepiness Scale). For the electroencephalogram (EEG) measurement, it was equipped with the electrodes based on the International ten-twenty electrode system (C3-A2, O1-A2, O2-A1). EEG activity in the alpha frequency band (8 – 12 Hz) is one of the most typical physiological indicator which represent the transition from wakefulness to sleepiness. AAT (Alpha Attenuation Test) which repeats three times each opened and closed eye for 1 minute was performed in a seating position with directions of the researcher in the beginning, in the middle and in the end of exposure to whole-body vibration. For analysis, power spectral analysis was conducted over the last 6 min of EEG, and wakefulness levels were defined as the ratio of mean alpha power during eyes closed versus eyes opened. The laboratory was kept at room temperature (21 ± 1.0 degrees C), humidity was 50 ± 5%, noise level was 63.6 dB (A) eq, and illumination 510 lx. Each experiment was started around 10:00 am to minimize the effect of biorhythm.

Jan 6, 2006

By Ronald J. Mathis

The objective of this contract is to design, build, surface test, and evaluate a breadboard prototype of the Variable Wall Mining System so that data are available for the design of a production machine. The Variable Wall Mining System (VWMS) consists of a series of side cutting augers, connected end to end, and distributed across a panel. Supplying rotary power at the end of the string and anchorage from conventional longwall roof supports, the augers are sequentially thrust into the face and then lifted to the roof to extract the coal in a continuous manner. The augers not only cut but also transport the coal. The effort described in this report summarizes the operation characteristics of the VWMS, the design methodology used to develop various working models, the surface testing of a ½ -scale version of the VWMS, prediction of power requirements and performance potential of a full-scale system, and a critique of the VWMS concept, conclusions, and recommendations.

Jan 1, 1987

[This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative Agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of tines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935.-36.3/ The present report cover brands of gasoline represented by 1,490 samples plus thus: from the Pacific Coat, which ;sere averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, Whereas in other areas only one Company reported on a brand. Thus, it can be seen that soma of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Severe changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas any western Tennessee. The Rocky Mountain area, have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and. Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico , and El Paso, Tex., have been combined to represent the South Rock Mountain district. The Cleveland district has been expanded to include Ohio ant. Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippee, and northern Florida.]

Jan 1, 1938

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Michael Agresti, David Rowe, Lin-Ling Zhang, Yuhui Yan, Paula Galaviz, Judith Marchant-Hanson, Ji-Geng Yan

Until now there has been controversy about which tests should be performed to diagnose early Hand-Arm Vibration Syndrome (HAVS). Initial screening questions, especially about tingling and numbness, routinely given to patients prior to examinations proved to be a very important tool in the diagnostic process1, 4. However, standardized tests that are simple, quick, valid and reliable are needed to support a diagnosis of HAVS. Purpose: To find the most valid and reliable tests to diagnose HAVS. Material and Methods Five major tests were performed on Group I and Group II. Group I: Control group of 12 volunteers including students, nurses, secretaries and physicians with no history of using vibrating tools (age 20 to 50y, mean age 38.5y; 5male, 5 female.) Group II: 12 workers (age 17 to 65y, mean age 39y; 9 male, 3 female) were sent by a local trade union with a history of using vibrating power tools on their jobs for varying amounts of time (mean 12.2y, from 0.5 to 35y.) Pre-enrollment survey showed that each had more than 4 complaints commonly associated with use of vibrating tools (including numbness, tingling, weakness, pain, finger color or nail changes, temperature change, and difficulty moving.) 1. Sensory nerve conductive tests: Amplitude and nerve conductive velocity (NCV) were evaluated. 2. Cold Stress-Temperature recovery time tests were done on the index finger of the dominant hand following these steps: Confirm water bath is within 4-5º C. Place the finger temperature probe on pad of the index finger of the dominant hand. Record temperature every 15 seconds. Place subject’s hand in the cold- water bath for exactly five minutes. Record temperature every 15 seconds for ten minutes. 3. Blood test: Venous blood was taken by a 21-gauge needle with the yellow collection tube adapter. S-ICAM, Sera Thrombomodulin, Norepinephrine levels were evaluated by Henderson Research Centre, Canada. 4. Finger Sensory Evaluation: Semmes-Weinstein monofilament test and 2-point discrimination tests were performed on bilateral fingers. 5. Digital blood pressure test: blood pressure was measured in bilateral index fingers. Results 1. Median nerve sensory conductive amplitude from palm to wrist : GI: mean 96 ± 31µm; GII: mean 43± 30µm; for dominant hands. GI vs GII: P<0.001

Jan 6, 2006

This report describes the development of training materials for the operators of underground mining equipment in the underground metal and nonmetal mining industry. The objective was to determine the effectiveness and acceptability of these training materials and to provide the validated training materials to the industry. Ten modules were developed, based on industry need according to accident frequency, accident severity and exposure to the equipment. The final modules were an average of 20 minutes in length and used slides with synchronized narration on cassette tapes. Testing materials are included for use by the mines.

Jan 1, 1984

By Ignaz Lichtig

[IN CONNECTION with its work on the conversion of coal to liquid cud gaseous fuels,3 the Bureau of Mines has always striven to keep informed of developments in this and related fields so that unnecessary duplication of effort could be prevented and so that useful ideas, presented in scientific and technical literature, could be evaluated as quickly as possible. Thus the E has compiled expensive literature and patent abstracts on the Fischer-Tropsch synthesis4 and hydrogenation d e venation of coal at elevated h temperatures and pressures.5 6 This publication differs from the references just given in that it covers patent applications, which may or may not have been approved for issuance as a patent, and also includes later material. The patent literature is, of courses, a valuable source for new ideas. German patent, have been particularly useful in this field because both processes for the complete conversion of coal to fluid fuels originated in Germany and were thoroughly investigated there because of the shortage or of indigenous fluid fuels. Among the German literature relating to these processes are patent applications. In contrast to the United States, Germany has a system in which applications are published before the final patents are issued. This arrangement permits the public to view all the applications and not just those for which a patent was granted as is done in the U.S. system. When main of the invention are judged not patentable by the German Patent Office, such documents nevertheless may contain useful ideas for scientists and engineers.]

Jan 1, 1961

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators&apos; shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators&apos; duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators&apos; noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

By P. R. Jones

The Bureau of Mines has written a computer program for the design and cost of a shell and tube type heat exchanger, in which a change in phase occurs on the shell side. The total cost, which was minimized, includes the annual fixed charges and annual operating costs. The program was written to meet the following requirements: (1) Triangular pitch, (2) single or multiple pass, and (3) heating or cooling. Price optimum design was obtained for four standard tube diameters and pitch. Standard heat exchangers whose area equaled or exceeded the required area are also listed. The program was made adaptable to various fluids and to various tube dimensions by including many of the required data such as physical properties of the fluids, tube data, and standard shell data as input data.

Jan 1, 1969

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By Wilton Johnson

The Bureau of Mines study indicates that land utilized by the mining industry for mineral extraction and processing from 1930 through 1980 amounted to 5.7 million acres, or 0.25 percent of the land mass in the United States. Land reclaimed by the industry during the same period was 2.7 million acres, or 47 percent of the land utilized. Land use by the mining industry includes surface land used for excavation or mining, for waste from underground mining, and for wastes from milling or processing operations. Data on land use for disposal of overburden waste from surface coal mines and on areas affected by subsidence associated with underground mining are included for the period 1930-71 only. The 10 leading States in total land used for mining over the 51-year period were, in decreasing order, Pennsylvania, Kentucky, Ohio, Illinois, West Virginia, Florida, Indiana, California, Alabama, and Missouri. Seven mineral commodities accounting for 92 percent of land use are, in decreasing order, bituminous coal, sand and gravel, stone, phosphate rock, clay, copper, and iron ore, all predominately surface mined. Bituminous coal production was responsible for nearly half of the total area utilized. Reclamation of mined lands and waste disposal sites over the reporting period was largely on lands utilized in mining bituminous coal; 75 percent of the land used for bituminous coal production was reclaimed.

Jan 1, 1981

By G. S. Scott, W. J. Huff, G. W. Jones, R. E. Kennedy

"INTRODUCTION This report gives preliminary results of field and laboratory investigations made at the request of the War Production Board relative to causes that have occurred during the last 8 months in acetylene-generat72,r plants in shipyards on the Pacific coast.Six acetylene-generator explosions have occurred in four shipyards. These explosions killed five operators, injured six others, and extensive damage to the plants involved and curtailmnent of vital defense Although the occurrence of acetyiene-generator explosions in other section of the United States is not known, it appears, at least, that if such have occurred, they have caused only minor damage and no loss of lives.The use of acetylene in shipyards on the west coast has expanded tremendously during the past 2 years. These shipbuilding, companies erected aletylene-generatcr equipment, which was soon found to be entirely inadequate to meet the needs of their expanding acetylene requirements for welding, cutting, shrinking, and other purposes, and instances found it necessary to operate their equipment at rates greater than deemed consistent with safe operating practice."

May 1, 1944

By F. E. Brantley

Research was undertaken by the Bureau of Mines to assess the technical feasibility of smelting cement-copper precipitate in an electric furnace to produce commercial-grade copper. The blister-grade copper produced in smelting was refined by gaseous oxidation and reduction methods to rive a product equal in quality to fire-refined copper. The cement copper used in the study was typical of the material produced in commercial operations. The sample product was received in a partially oxidized state and analyzed 77.5 percent Cu, 3.4 percent Fe, 0.8 percent Pb, 0.05 percent Ni, 0.6 percent Sn, and 0.9 percent S. Smelting tests were made on the precipitate using laboratory-size induction and electric-arc furnaces. Three types of furnace linings were tested during, the investigation: Carbon, including graphite; clay-graphite; and silicon carbide. Although all proved satisfactory, either carbon or graphite was preferred because of their superior refractory properties and low permeability to molten copper. Copper recoveries in the induction and arc smelting tests averaged 92 percent in commercial-grade metal assaying 99.8 percent copper. Refining the molten copper by oxidation and gaseous reduction or by chlorine lancing increased the purity to plus 99.9 percent.

Jan 1, 1961

By Larry G. Stolarczyk

Jan 1, 1980

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

By J. L. Howell, D. E. Pollock, A. B. Cecala, A. D. O’Brien

Dust from worker,s clothes has been shown to be a problematic source of personal dust exposure. A recently completed effort between NIOSH and the Unimin Corporation has resulted in a quick and effective way to clean worker clothing. The process involves a booth under negative pressure with an air spray manifold to supply compressed air to blow off the dust from the clothing. The overall system is designed to meet MSHA and OSHA requirements. Results of field testing indicated that the manifold cleaned the clothes 10 times faster and removed 50% more dust than cleaning methods used by workers today.

This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covers 54 brands of gasoline represented by 1,480 samples plus those from the Pacific Coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Several changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas and western Tennessee. The Rocky Mountain areas have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico, and El Paso, Tex., have been combined to represent the South Rocky Mountain district. The Cleveland district has been expanded to include Ohio an,"- Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippi, and northern Florida.

Jan 1, 1938

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965

By Jon C. Volkwein

The U.S. Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low-profile mining machine. Tests were conducted in a full-scale model mine using a continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters tested included mining position, depth of cut, brattice setback, and combinations of scrubber, and directional or symmetrical sprays. Results indicated that either water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 20-ft blowing curtain without sprays. No FVE values were less than the standard 20-ft blowing results.

Jan 1, 1989