Search Documents

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

By V. L. SKITSKY

Geophysical Abstracts are published by the Division of Geophysical Explo- ration of the U. S. Bureau of Mines as an aid to those engaged in geophysical research and exploration. Inasmuch as geophysicists in the field may have little opportunity to consult libraries, the policy of the Division is to provide abstracts suffi- ciently informative in themselves to keep readers abreast of literature and patents published in the United States and abroad. - DISTRIBUTION. Abstracts 1-86 were issued as Information Circulars by the Burca of Mines; Abstracts 87-111 appeared as Bulletins of the Geological Survey; Abstracts 112-127 have been published as Information Circulars by the Bureau of Mines; succeeding issues will be resumed by the Geological Survey.

Jun 1, 1947

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By P. B. Altringer

The Federal Bureau of Mines conducted a study to determine if residues from fractional distillation represent a potential source of mineral values. A literature review and discussions with tar sand specialists failed to disclose the mineralogical nature of residues remaining after bitumen extraction. To develop this information, pilot plant tar sand residues or toluene-cleaned tar sands from 23 deposits were examined. The nature of the residues was determined by standard mineralogical methods and the chemical compositions were determined by X-ray and ICP (inductively-coupled plasma spectroscopy). None of the sands or concentrates examined contained sufficient valuable minerals to be economically important.

Jan 1, 1982

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By W. D. Striffler

Land disturbed by surface mining in Colorado and other western states has increased substantially over the past several years and is likely to increase even more in the future. This study was initiated to provide basic information on hydrologic and erosional characteristics of regraded coal spoils in Colorado as an aid for planning future reclamation activities. Eleven of twenty-one surface mines licensed in Colorado were sampled during the summer of 1980 and 1981. Mines not sampled included mines which had not progressed to the point that reclamation had begun, and mines where operators denied permission to sample. All coal regions were sampled with the exception of the San Juan Coal Field. Physical and hydrologic characteristics of regraded coal spoils in Colorado were determined using standard field and laboratory procedures. Field sampling included characterization of sites (slope, vegetation density, proportion of surface rock, bare soil, etc.) and infiltration measurements using a l-meter square drop former raining on a 1/2 square meter rectangular plot frame. Core samples collected in the field were analyzed for saturated hydraulic conductivity, bulk density, organic matter, moisture retention and texture. The erosion potential of each site was determined using the Universal Soil Loss Equation (USLE). Results of the sampling indicate that infiltration rates vary widely both within and between sites. However, definite trends with respect to coal fields are apparent. For example, the Green River (Yampa) coal region had a wide range of sampled infiltration rates (1.2 to 5.1 cm/hr). However, most of the sites clustered towards the low end of the range. The North Park (Marr Strip) also was rated at the low end of the infiltration range (2.0 to 3.0 cm/hr). Average infiltration rates for the Canon City and Uinta Coal Regions were at the high end of the range (4.9 to 5.5 cm/hr). Multiple correlation analysis of infiltration rates vs. site characteristics showed that infiltration rates were most closely correlated with the depth of wetting, the amount of mulch cover, and site slope. The depth of wetting was highly correlated with the depth of the topsoil and the bulk density of the spoil. In general, the topsoil at all sites appeared to be highly permeable to water intake but once saturated, subsequent infiltration depended upon characteristics of the underlying spoil. Vegetation cover affected infiltration on individual mine sites but was not as pronounced as topsoil characteristics or mulch. Erodibility of topsoil and spoils, as determined by Wischmeier's "K" factor, ranged from 1.34 to 0.56 tonnes/ha. (topsoil) and 1.25 to 0.66 tonnes/ha. (spoils). Definite trends in erodibility are evident. The Green River (Yampa) Coal Region displayed consistently higher erodibilities (1.34 to 0.75 tonnes/ha.) than other coal fields (0.72 to 0.56 tonnes/ha). Lowest erodibilities were observed in the Uinta, North Park, and Raton Mesa Coal Regions (0.56 to 0.62 tonnes/ha). Erodibilities of underlying spoils showed similar trends as the topsoils. Erosion potential (the product of soil erodibility and rainfall erosivity) was detennined using calculated ?K? factors and rainfall erosivities (R) taken from Clyde (1976). Results show that the Delagua coal field, Raton Mesa Coal Region had the greatest erosion potential due to the high rainfall energies in the region, while the North Park and Uinta Coal Regions had the lowest potential erosion.

Jan 1, 1981

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963

By Gary A. Kingston

Low-cost hydroelectric energy in the Pacific Nortnwest has been an important factor in the development of a ferroalloy industry. Eleven companies, employing approximately 1,000 persons, produce about 116,000 tons (1954-58 average) annually of ferrosilicon, ferrochromium, ferromanganese, ferrophosphorus, silicomanganese, and ferronickel. About 7,500 tons (1954-58 average) of these ferroalloys is consumed in the Pacific Northwest States of Washington and Oregon; the rest is used principally in other western and mid-western markets. In 1959, the Bureau of Mines began a study to determine the current status and to evaluate the potential of the ferroalloy industry in the Pacific Northwest. The Bureau gathered information from operating alloy plants in Oregon, Washington, Idaho, and Montana; from published materials; and from consumers of ferroalloys.

Jan 1, 1962

By Joseph M. Kurtak

The U.S Bureau of Mines conducted a five-year mineral resource assessment of the 16.6 million acre Colville Mining District in northern Alaska, which includes part of the National Petroleum Reserve in Alaska. The study was initiated at the request of the Bureau of Land Management, which administers the majority of the region. The study was done in cooperation with the Alaskan Division of Geological and Geophysical Surveys, the U. S. Geological Survey, and the University of Alaska. During fieldwork, 1593 rock, soil, and stream sediment samples were collected and four bulk samples taken for beneficiation studies. A total of 40 mineral occurrences were documented, including 27 which were previously undescribed. No mining has occurred within the district. Mississippian carbonaceous shale and siliceous mudstone contain stratiform exhalative lead-zinc-silver occurrences. Grades average 8.0% combined lead/zinc and 51 gm/mt silver. Upper Devonian to Lower Mississippian sandstones host breccia veins, containing up to 29% combined lead/zinc and 274 gm/mt silver. Mineralized quartzites of similar age have potential for disseminated-type lead-zinc deposits. Samples from Lower Cretaceous mudstone and shale beds up to 6.5 meters thick, contain as much up to 12% manganese. Upper Mississippian carbonaceous shale and limestone beds contain up to 23% phosphate. Stratiform barite deposits hosted by cherts, are up to 27 meters thick with an average specific gravity of 4.16. Vein-type fluorite occurrences are associated with Mississippian limestone. Moderate potential exists for development of zinc -lead-silver, barite, and phosphate deposits.

Jan 1, 2011

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

By P. R. Jones

A computer program was written for the design of a shell and tube heat exchanger on a price optimum basis for the following conditions: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; (4) no change in phase; and (5) inside pumping costs immaterial. Price optimum design was obtained for four standard tube sizes and standard pitch. The inside pressure drop was fixed and outside pressure drop was computed for the optimum baffle spacing and when the baffle spacing equaled the shell diameter. Standard shells whose areas equaled or exceeded the required area were also listed. The program was made adaptable to various fluids and to various tube sizes and pitch by reading in many of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1968

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

By Richard L. Sanford

This report summarizes the results of an update on a previous Bureau of Mines grant (G0264026), and includes 5 additional years of computer pro-gram development. The directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various governmental agencies. References to computer applications throughout the industry are presented as well as comments on program availability. The work effort on the updated directory concentrated on programs that are available to the public and are well documented.

Jan 1, 1982

Underground coal mining continues to evolve in the U.S., and more reserves are being mined under deeper cover, with worse roof, or with interactions from previous workings. At the same time, the mining community is responding to higher safety standards and intense competitive pressures. The need for effective ground control design has never been greater. Ground control safety issues that have been addressed by recent the National Institute for Occupational Safety and Health (NIOSH) research include: Improving roof support performance; Maintaining safe tailgate escapeways from longwalls; Optimizing pillar design for retreat mining; Controlling multiple seam interactions; Predicting roof conditions during extended cuts, and; Preventing massive pillar collapses. As funding from both government and the private sector has diminished, the emphasis in research has focused on providing the mining community with practical techniques for improved ground control design. Many projects have successfully employed empirical methods that emphasize the statistical analysis of case histories from underground mines. Other projects have employed numerical models and large-scale laboratory testing of roof support elements. Using these data, NIOSH has developed an entire toolbox of computer programs that have been effectively transferred to the mining community.

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934