Search Documents

By Robert A. Bruce

A motion transducer based on coherent mixing of laser light backscattered from rough surfaces is evaluated in terms of sensitivity, bandwidth and range. Tests made with a prototype composed of a 4-mw HeNe laser, a silicon avalanche photodiode, and a 15-cm aperture telescope demonstrate that remote measurements with reasonable bandwidth and accuracy are feasible at distances up to 100 meters.

Jan 1, 1977

By R. F. Waters

The Bureau of Mines developed laboratory-scale processes to recover sodium phosphates and metal values from waste sludges generated by the phosphate treatment of automobile and appliance components. After treatment of the sludge with NaOH, followed by coke or hydrogen reduction and sintering, zinc and lead were recovered as fume; the sinter was separated by leaching into a metallic product, chiefly iron and nickel, and high-purity disodium or trisodium phosphate.

Jan 1, 1971

By J. Hanslovan, R. H. King

An investigation of the feasibility of shielding low-voltage trailing cables in underground coal mines is described. Both laboratory and under¬ground installation results are presented. The main objective of shielding is to reduce the electrical shock hazard; however, several problems will be encountered by mine operators who install shielded cables. Parameters related to such items as purchasing, splicing, troubleshooting, safety, and reliability are discussed. Some of these problems can be minimized by changes in cable constructions and shuttle-car reeling-device components. Both SH-C and SH-D constructions are considered.

Jan 1, 1979

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974

By Fred N. Kissell

Methane flows and pressures were measured in mines in the Pittsburgh, Hartshorne, and Pocahontas No. 3 coalbeds. From the data, the permeability of each of these coalbeds was computed. It was found to depend strongly on the type of coal and on the amount of water in the coalbed, and it was found to increase with time. All of the coalbeds had a high-permeability zone adjacent to the face or rib, and the Pittsburgh bed exhibited directional anisotropy. Surprisingly, little or no overburden effect was observed.

Jan 1, 1972

Increase the safety of underground mine workers by minimizing hazards associated with rerailing mine cars after derailment. Background and Approach A serious operational problem in underground mines is the task of rerailing mine cars. Current rerailing practices are not only hazardous but are inefficient as well. Most methods involve pulling the derailed car back onto the track with a locomotive. This causes damage to the road bed and is not effective on curves or in situations where the car's wheels are too far from the rails. Jacks, wooden props, and pry bars are also used to raise or lower cars back onto their tracks but methods involving these tools require much strenous manual effort by mine workers, thus posing possible serious injuries. The problem is further compounded by the cramped, narrow confines of the underground mine environment which allows no space to permit use of cranes or other surface railroad rerailing techniques. The Bureau of Mines, aware of these problems, investigated improvements in current underground rerailing methods. Through a cooperative effort with Hoesch MFD, a system was designed and modified that can be easily carried into the mine by workers and quickly assembled at the derailment site. The system is hydraulically and pneumatically powered rather than reliant upon manual operation.

Jan 1, 1986

By Stephen A. Hare, O&apos

The melting, casting, and welding of the Raney nickel alloy (42 pct Ni-58 pct A1), a methanation catalyst useful in coal gasification, were investigated. Melting was done in graphite crucibles by heating aluminum and adding nickel using a cryolite slag cover. Casting conditions were found to be optimum when the melt temperature ranged from 1,125° to 1,200° C and the mold temperature ranged from ambient to 250° C. Suitable mold materials were found to be quartz, heat-resistant glassware, olivine, and zircon. Welding of the alloy can be accomplished using tungsten inert gas process. Tensile strength of the alloy, in the as-cast condition, was found to be 2,000 1b/sq in with an impact strength of less than 1 ft-1b. The coefficient of thermal expansion was determined to be 18.4 x 10-6/° C after heat treatment.

Jan 1, 1977

By Barbara J. Halpern

There?s no denying that mining is a male-dominated industry. Yet thanks to technologies developed over the last 20 years, societal changes in sex role stereotyping, individual determi­nation, and the willingness of companies to train women, there are no jobs in mining today where women are not represented. Women are drillers and electricians as well as drivers of heavy equipment and haulpack trucks. They perform jobs ranging from field exploration and metallurgy to clerical and janitorial and warehousing positions, from prospectors and underground blasters to geologists and land reclamation experts, from communicators to legal experts on mining law and more. The Women?s Mining Coalition, founded in 1994 to shepherd responsible legislative mining reform, estimates that 20 percent of the workers in the mining industry are women. Although women are concentrated in clerical and adminis­trative jobs, at least 10 percent are in non-traditional, hardhat jobs, claims the group. There are women in management, but the numbers in senior management remain small, especially in larger companies.

Feb 1, 1998

Reduce longwall shearer operators' dust exposures by more effectively suppressing the dust generated by the upwind cutting drum. Approach Direct more of the shearer water supply to the upwind drum, thus reducing the shearer operator's exposure to respirable dust while making more efficient use of water. How Proportioning Permits More Efficient Use of Water On most longwall mining operations, the cutting action of the shearer drums is the primary source of dust. Al-though the amount of dust generated is directly related to the amount of coal and rock cut by the drum, the exposure or the shearer operators to dust depends more on their work position relative to the upwind drum. When cutting with the airflow, the upwind drum, cutting bottom coal and floor rock, is the primary generator of dust reaching the operators. The lead drum is downwind of both shearer operators and is thus of less concern. (See diagram). When cutting against the airflow, the lead drum is upwind-taking a full cut, including roof rock-and both shearer operators may be exposed to very high levels of respirable dust. Currently, water sprays mounted on the cutting drum provide the most effective method of controlling dust from longwall shearer drums, and all longwall mining operations use some type of bit flushing or cavity filling water spray system on the cutting drums. Bureau surveys of longwall operations, conducted as part of its research program to reduce respirable dust, have indicated that six longwalls with better than average compliance records use higher than normal water flowrates to the cutting drums. The average water flow to the shearers at these six operations was approximately 60 gpm-about 50 percent more water than is normally supplied to double-drum longwall shearers.

Jan 1, 1982

By John C. Edwards

The Bureau of Mines has developed a time-dependent droplet vaporization model (in the absence of forced convection) that can be applied to the vaporization of liquid Halon 1301 droplets (vapor pressure at 300 K = 14 atm) sprayed from an extinguisher. It was found that rapid surface vaporization quickly lowers the droplets' surface temperature very near to the boiling temperature, and the vaporization becomes diffusion controlled. Although the lifetime of the droplet is proportional to the square of the initial radius of the droplet, the elapsed time prior to complete droplet vaporization is not proportional to the square of the droplet radius, as an equilibrium model would indicate.

Jan 1, 1982

By K. O. Bennington

The thermodynamic properties of pollucite [(Cs0.650Na0.185Rb0.028)(AlSi2) (05.8630H0.137)?0.19H201 were determined by the Bureau of Mines in collaboration with the Argonne National Laboratory. The standard enthalpy of formation determined by hydrofluoric acid calorimetry is ?Hf°298 = -3,098.52 ±3.63 kJ mol-1. The standard enthalpy of formation from the oxides is ?H298 (from oxides) = -209.50 ±2.38 kJ mol-1. Low-temperature heat capacities were determined by adiabatic calorimetry from 5.0 to 306.1 K. The derived standard entropy is S°298 = 207.24 ±0.43 J mol-1k-1. Enthalpy increments above 300 K were measured by copper-block drop calorimetry from 349 to 674 K. Various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation and Gibbs energies of formation are given as functions of temperature. The Gibbs energy of formation is ?Gf°298 = -2,919.9 W mol-1

Jan 1, 1983

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

By George H. Johnson

An evaluation of the diamond-bit-performance data accumulated from core-drilling cherty limestone and cherty dolomite reveals that the percentage of core recovered and the physical characteristics of the bits and diamonds used are economically significant. One of the established trends, of particular interest to those engaged in diamond drilling, is that bits set with small, low-quality, West African drill bort are the most economical. Detailed analysis of the factors that affect diamond-bit performances, such as diamond size and quality, bit size and type, percentage of core recovered, and the physical characteristics of the bit matrices are assessed in the tables, charts, and discussion.

Jan 1, 1958

Minimize airborne respirable quartz dust produced by continous mining machines. Approach Install a shovel-mounted underboom water spray system on the off-curtain side of the mining machine. Dusty air containing quartz is momentarily trapped under the boom, where it is captured by fine spray mist. The remaining dust cloud is directed immediately behind the curtain before it can migrate back to the machine operator's location. How It Works Previous studies have shown that most of the dust generated by continous mining machines occurs under the boon as the cutter head shears down. The primary source of respirable quartz dust on many continous mining operations is cutting or trimming roof rock immediately prior to shearing. This results in very high concentration , of

Jan 1, 1989

By S. J. Anderson

The Bureau of Mines compared three methods of rock cutting using drag cutters under controlled laboratory conditions. The methods tested were the conventional drag cutting method used on continuous miners, the kerf-core method used on some boring machines, and an experimental method called ripper cutting. All three methods were tested in blocks of Indiana and Kasota limestone. The results of this testing showed ripper cutting to be 30 to 40 pct more energy efficient than both the conventional and the kerf-core methods in Kasota limestone and 35 pct more efficient than the kerf-core method in Indiana limestone. The conventional method was, however, 9 pct more energy efficient than the ripper method in Indiana limestone. These results are considered promising, and more tests are planned with the ripper cutting system.

Jan 1, 1987

By W. S. Sanner

A High Splint coal was carbonized in a low-temperature, fluidized-bed sys-tem to study the effects of thermal cracking on the products of decomposition. The coal was fluidized in recycle gas at 485° to 600° C, and the products were cracked at 600°, 700°, and 800° C in a bed of fluidized coke. Yields of tar, pitch, paraffins, and olefins decreased as carbonization temperature increased. Thermal cracking of the tar vapors produced the highest tar yields at 600° C, and light oil yield increased at cracking temperatures up to 700° C. At an 800° C cracking temperature, the yield of light oil decreased.

Jan 1, 1969

By Aarne Visnapuu

Pneumatic chipping, scaling, and grinding can expose the tool operator to noise levels in the range 90 to 120 dbA. In most chipping and scaling operations, casting resonance is the primary source of noise, followed by air exhaust, and machine and chisel resonance. In grinding, the air-exhaust noise predominates. The Bureau of Mines has shown that noise from these operations can be reduced by up to 15 dbA. Workpiece resonance was reduced by sand or other damping methods; tool resonance, by internal damping; and chisel resonance, by constrained-layer treatment. Mufflers reduced air-exhaust noise, and an acoustically treated booth was effective in containing noise around the work area without increasing operator exposure.

Jan 1, 1977

By Fred C. Turin, Kim M. Cornelius

Work in underground coal mines is repetitive and physically demanding. Workers commonly report a wide range of aches and pains. Management at one mine was concerned about increased reporting of aches and pains by roof bolting machine operators. An analysis of roof bolting tasks was conducted at this mine to identify early warning signs of cumulative trauma. Health and safety risk factors were identified and recommendations to reduce cumulative trauma exposure were provided. Recommendations addressed job procedures, equipment design, and worker awareness of risk factors.

By C. B. Manula, R. L. Sanford, R. A. Rivell

Part I. DATA INPUT ALTERNATIVE 1

Jan 1, 1974

By Pablo Velasco

Ecuador had limited mineral output, al-though the Government attempted to stimulate metallic mineral exploration and also evaluated a gypsum and a phosphate deposit. A pilot plant to exploit gold deposits was established, and there was extensive gold exploration activity in southern Ecuador. Domestic output of iron and steel declined sharply. Among all minerals, petroleum output was the dominant factor with both exports and production increasing significantly over that of 1988. Crude oil exports contributed 63% of total export earnings and about 70% of the central Government's revenue.

Jan 1, 1986