Search Documents

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By J. E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to determine the influence of mining machine-mounted scrubbers on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery with a model mining machine that simulated airflow created by a dust scrubber. During the tests, ultrasonic anemometers were used to measure airflow speed and direction at several locations near the face. For the same test conditions, methane was released from the face and gas concentrations were measured at 21 locations above the machine using fixed point methanometers. Changes in airflow speed and direction are correlated with scrubber airflow and the measured methane distribution above the mining machine. The research results showed that operation of machine-mounted scrubbers improved face ventilation when blowing ventilation is used by increasing both the intake flow and the quantity of air reaching the face.

By W. W. Agey

As a part of the program of investigation of domestic sources of manganese in the western United States, engineers of the Bureau of Mines examined. and obtained samples of ore from two properties in the vicinity of Barstow, San Bernardino County, Calif. In addition to these, samples from two other properties in the same vicinity were submitted by the owners. As the ores were too low-grade to be acceptable for the direct production of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration by ore dressing. The Big Reef manganese claims axe about 140 miles east of Barstow, Calif. The claims were leased by W., E. Thurber of San Gabriel, Calif., from the owner, C. S. VanDoren of Daggett., Calif. Manganese oxides occur as a replacement deposit in heavily brecciated andesite along a fault plane. Four samples were taken by an examining engineer of the Bureau of Mines from the ore zone, which, when composited, were representative of all the exposed ore. Preliminary tests were made on lot B, and final tests wore made on the composite sample. The Trans-Oceanic property is about 20 miles southeast of Barstow, near Newberry, in the. Pisgah mining district, Calif. The sample, submitted by the owners, was taken from a 1,000-ton reject clump from a hand-sorting operation. The ore occurs as a replacement of rhyolite.

Jan 1, 1952

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By Richard A. Watson

A frequency-shift keying (FSK) modulator-demodulator (modem) network has been devised for the Bureau of Mines mine-monitoring systems. This network permits an unlimited number of remote stations to communicate with one central station over the same pair of wires. The network operates at a speed of 4,800 Bd at distances up to 5 miles. This report describes the development and operation of the modems. The theory of operation, schematic diagrams, and printed circuit board layouts are provided. Although the modems were built for a specific application, a more general use is discussed whereby the network would operate with a typical serial channel format.

Jan 1, 1985

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By R. R. Sayers

The increasing use of hydrogen fluoride (annual consumption now exceeds 500,000 pounds (1)4/) directly and its occurrence as a byproduct of the utilization of fluorine compounds in the mineral industries, especially in metallurgical processes and in the refining of petroleum products, has aroused interest in its toxicity, and a brief review of the literature, with special reference to the hazard of poisoning in the mineral industries, seems to be opportune. Recently, residents in the vicinity of aluminum plants have been complaining of injury to livestock and vegetation as well as to their own health from the gases discharged into the air during operation of the plants, hydrofluoric acid gas apparently being the offender. The comparatively recent utilization of hydrofluoric acid in the alkylation process for the production of high-octane gasoline has raised the question of the hazard of poisoning in the petroleum Industry. In addition, the use of fluorine-containing refrigerants has extended the potential al exposure outside of industry (2).

Jan 1, 1945

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1976

By James M. Baugher, Donald W. Conrad, William J. Wiehagen

This report describes a process for quickly developing information that is useful for skills training. The process is called job training analysis (JTA). Its main use is to structure skills training at the jobsite. JTA supports structured skills training by identifying the job duties, tasks, and steps and the reasons why those job components are important. The outcome of the JTA process is a worksheet—a training outline based on the knowledge and expertise of experienced workers. Time invested in developing a JTA will result in significantly more time saved when it is used appropriately by skilled trainers. Like a roadmap, JTA saves time and energy. Experimental work at several mine sites helped document, refine, and validate the JTA process. JTAs for two mining jobs—roof bolting and lift truck operation—at two different mine sites are used to illustrate some of the concepts and the specific JTA process described in this report. The work at these two sites was influenced by cooperative work between the Mine Safety and Health Administration (MSHA) and the National Institute for Occupational Safety and Health (NIOSH) at several other mine sites and prior collaborative work with the U.S. Navy. The mining JTA process is grounded within the military research on the design of instructional systems. MSHA and NIOSH worked to simplify and apply the military training development model for mining industry use through collaborative work at several mine sites. The JTA process involves three activities: (1) planning, (2) a 1- to 3-day workshop where the JTA is developed using facilitated work with subject-matter experts, and (3) followup. Guidelines and considerations for each of these activities are included. Results indicate that the JTA process has been well received and valued by mining industry participants. It blends aspects of health and safety, production, maintenance, and crew coordination.

Jan 8, 2006

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of fluorspar (CaF2) from 36 U.S. and 50 foreign mires and deposits in 13 countries. Only 6 U.S. properties are considered to be economic, as 29 domestic deposits were found to have an average total cost of production that was uneconomical at a breakeven (0-pct) discounted-cash-flow rate of return (DCFROR). The 50 foreign properties evaluated represent at least 55 pot of demonstrated fluorspar resources located in market economy countries and China. Al I evaluated foreign operations were found to be economic to marginally economic in January 1984 dollars when compared against published prices for each country. Reserves for 56 properties totaled 97 million metric tons (mt) (recoverable Ca F,) from demonstrated ore resources of 344 million mt that contained 123 million mt CaF2. The average total cost needed to cover all costs over the life of each operation was determined for all recoverable fluorspar products. Comparisons of ruining, beneficiation, and transportation costs per metric ton of fluorspar concentrate illustrate advantages between countries. Of the three countries with the greatest fluorspar production, China, with its high-grade, low-cost operations had the lowest weighted-average total cost of production ($38/mt concentrate), Mexico was next, at $54/mt concentrate, and benefited in U. S. dollar terms from the devaluation of the peso. The Republic of South Africa needed an average of $90/mt of concentrate to cover all costs of production at its large low-grade deposits.

Jan 1, 1985

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

1. BOYD, JAMES. Statement on the Investigation of Natural Resources. Hearings before National Re-sources Economic Subcommittee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 125-131. 2. BUCH, J. W., HENDRICKS, T. A., AND TOENGES, A. L. Statement on the Investigation of Natural Resources. Hearings before National Resources Economic Sub-committee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 231-235. 3. CONGRESS, U.S. An Act to Provide for the Establishment and Operation of a Research Laboratory in the Pennsylvania Anthracite Region for Investigation of the Mining, Preparation, and Utilization of Anthracite, for the Development of New Uses and Markets, for Improvement of Health and Safety in Mining, and for a Comprehensive Study of the Region to Aid in the Solution of Its Economic Problems and to Make Its Natural and Human Resources of Maxi-mum Usefulness in the War Effort. Public, No. 812, 77th Cong., 2d sess. (S-357), ch. 764, approved Dec. IS, 1942, 2 pp.

Jan 1, 1962

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation's coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965

By Susan B. Robertson, Gregory E. Hinshaw

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100%can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

By Henry P. Wheeler

As recently as 1915, helium was available only in very small quantities at a cost equivalent to $2,500 per cubic foot. It was a laboratory curiocity, and its properties were of interest to a limited number of scientists (11).3/ During the past 30 years, however, helium has grown from a plaything of scientists to a factor of importance in the prosecution of the recent war. Navy blimps filled with nonflammable helium proved to be more than a match for German submarines operating in the Atlantic. American bombers were able to fly unheard-of distances to drop bombs on Tokyo, Nagoya, Yokahama, and other Japanese cities because they had been made lighter with magnesium, arc-welded in a helium atmosphere. The Army utilized helium-filled radio-sonde balloons to obtain vital information concerning weather conditions affecting D-day invasions and other military maneuvers.

Jan 1, 1946

By S. Peterson, E. C. Westman, P. L. Swanson

Coal bumps are brittle, violent failures associated with high stresses and competent host strata. To study bump mechanisms, conditions in the vicinity of a deep longwall mining face in bump-prone strata were monitored using three discrete systems. First, a microseismic monitoring network recorded mining-induced seismic events throughout the mine and surrounding strata. Second, pressure variations and distributions on the longwall shield legs across the face were recorded. Last, tomography surveys imaged seismic transmission properties ahead of the face. Results from the three systems were correlated in an effort to increase understanding of mining-induced stress redistribution and bump potential. An initial, one-week study showed that the correlation between averaged tomogram values and seismically active areas had a coefficient of correlation (R) of 0.89. Further results of these studies demonstrate that the tomography system is capable of imaging heavy shield-leg loading and bump-prone conditions prior to them disrupting the face operations.

By Mark Sanders

This report compares a proposed 10/60 "piggyback" 02 generating self-rescue unit to the standard CO self-rescue unit with respect to work task interference. A simulated low seam coal mine was constructed and subjects performed locomotion, shoveling, cart pushing, and timbering tasks with the 10/60 or self-rescuer attached to their belts. Task completion time was longer on all tasks when wearing the 10/60 unit, although only locomotion was statistically significant. The 10/60 unit was bumped over 100% more often than the standard self-rescuer. Implications for design of the proposed 10/60 container are: 1) unit?s container must be extra durable to withstand the added abuse it is likely to receive by low coal miners; and 2) extra consideration must be given to preventing the device from slipping on the belt while working, especially in low coal.

Jan 1, 1980

By Gerald T. Homce, James C. Cawley

Electrical arcing injuries are the most common form of electrical injury in mining. MSHA data show that 381 "non-contact electric arc burn" injuries occurred in the mining industry from 1996 - 2005. A more detailed study of data from 1990-2001 showed that five types of apparatus - circuit breakers, conductors, nonpowered hand tools, electrical meters and test leads, and connectors and plugs were involved in two-thirds of the lost workday injuries. Many of the protections from electrical arcing injury available to workers in other industries stem from the application of National Fire Protection Association Standard 70E - Standard for Electrical Safety in the Workplace (NFPA 70E). NFPA 70E is a generally accepted industry guideline document, but excludes underground mining from its scope. Many of its practices and procedures, however, can be applied in the mining workplace to supplement the existing electrical safety requirements of Title 30 Code of Federal Regulations. This paper describes how NFPA 70E can be applied to mining workplaces after an analysis of the mine power system electrical arcing hazards has been completed (and Hazard/Risk Categories determined) using the tables from NFPA 70E or the calculation method as described in IEEE 1584. NFPA 70E can then be used to determine the levels and types of personal protective equipment (PPE) needed to protect miners against burn injuries. Appropriate lockout and tagout (LOTO) procedures for use in the mining industry are also described. Suggestions for better selection of electrically-rated hand tools are included. Recommendations for electrical meter selection and use based on transient withstand capability are also discussed.

By Louis R. Iverson

Patterns of species colonization, biochemical interaction among species, and competitive phenomena were studied in four reclaimed areas in western North Dakota ranging in age from one to four years after mining, along with a site from a native mixed grass prairie for comparison. Early successional changes in floristic composition and soil chemistry were quantified. The mined sites had been contoured, topsoiled, fertilized and seeded. Despite seeding of agronomic species, initial colonization was by fugitive species; analysis of the seed bank in topsoil showed that the most dominant colonizers immigrate after topsoiling. Of the 95 species encountered, Kuchia scoparia was the most dominant in the first two years following mining. Kochlo had relatively low densities in the first year (50-80 plants m-2), but was robust and attained heights of 88 cm with a biomass of about 400 g m-2 In the second year, the plant densities increased to over 10,000 plants m"2 but the height and biomass were reduced to 15 cm and 90 g m-2. However, during the third and fourth years Kochia density declined and was practically non-existent by the fourth year, while the planted Agropyron grasses had concomitantly increased. Other pioneers like Amaran thus retroflexus, Chenopodlum album, Helianthus annuus, Salsola spp. And Setaria spp. showed a less abrupt but similar decline. Chemical analysis of the soils over the same time period showed decreases in electrical conductivity (E.C.), and in the concentrations of P, Ca, Mg, Na, Li, Sr, and SO4 (due to leaching), while N increased. Field studies were conducted on the competitive relations between the dominant species - Kochia scoparia and Agropyron spp. - during early succession. It was found the Kochia acted as a "nurse" crop for several months during the first year of Agropyron spp. establishment, but then began to shade heavily by late July, thus reducing grass tillering. Field and growth chamber experiments on the intraspecific competition relations of Kochia demonstrated that its density and dry matter production, per plant and per unit area, conformed to several laws of plant population biology. Autotoxicity or the depression in growth of a species by its own degradation compounds, in Kochia, appears to be the main factor causing the decline in its growth. Results from a field experiment indicated that thinning dense second year Kochia stands to the density of first year stands did not alter the growth of Kochia, providing strong evidence for autotoxicity. Similarly, several growth chamber experiments demonstrated that small amounts of decaying Kochia leaves and especially roots were toxic to Kochia growth, but not Melilotus officinalis or Agropyron canlnum, Chemical analysis of the soils and plant tissues indicated nutritional im¬balances as shown by P/Mn and P/Zn ratios may be responsible for autotoxicity. In addition to Kochia, a bioassay experiment showed allelochemics to be important in several other colonizing species. Although our results indicate that later stage species generally have greater toxicities than first year colonizers, autotoxicity in the very initial stages seems to be accentuated by harsh habitat conditions. Several practices (mowing. fire, etc.) are used to manage grasslands. Mowing of the first year erect, annual, colonizing vegetation was shown to be beneficial in the growth and establishment of wheatgrasses after mining in western North Dakota. Plots containing Kochio predominantly were mowed in mid-and late-July, and in mid-August, during the first year of growth after recontouring, replacing topsoil. seeding and fertilizing. It was found the Kochia densities were reduced to two percent of the control and its biomass reduced to less than one-third when the area was mowed in mid-August. On the other hand, wheatgrasses showed increases of 23% in stem density and 860% in biomass production over the controls when mowed in mid-August. The mowing of Kochia just before seed-set apparently reduces interspecific competition between Kochia and Agropyron spp. during the following growing season. The method is highly recommended for use in hastening the establishment of planted grasses.

Jan 1, 1982