Search Documents

By Doug Tesarik

The study of neutrinos?particles infinitesimally smaller than atoms?would be significantly advanced if a deep underground facility were available that would filter out unwanted cosmic radiation. Encouraging progress has been made in satisfying the criteria for such a facility with the selection of the Homestake Mine in Lead, SD, by the National Underground Laboratory Committee as the recommended site for a National Underground Science Laboratory (NUSL). The Homestake Mine is America?s oldest and deepest underground mine, and its well-maintained infrastructure to depths of 2438 m below the surface makes the mine an excellent site for such a laboratory. The investigation reported here is an initial study of the stability of the first of the proposed chambers. A cylindrical room with a dome-shaped roof and floor was analyzed in three dimensions using the finite-difference program FLAC3D. The results were compared to recommended support requirements based on Barton?s Tunneling Quality Index, Q. Based on model results and observations from previous mining studies, large rooms with 50-m roof spans can be constructed and will remain stable at 2141 m below the surface in the Poorman Formation when the rock is reinforced with cable bolts. Construction may be possible at lower levels in the Yates Formation if more extensive laboratory strength tests confirm initial results.

Jan 1, 2002

By Thomas J. Fisher, Thomas Novak

Strong circumstantial evidence suggests that lightning has initiated methane explosions in abandoned and sealed areas of underground coal mines. The Mine Safety and Health Administration (MSHA) investigated several of these occurrences within recent years. The investigated explosions occurred at significant depths, ranging from 500 ft to 1200 ft. Data from the National Lightning Detection Network indicate a definite correlation between the times and locations of the explosions with those of specific lightning strikes. This paper addresses the question, "Can lightning cause potential differences capable of igniting methane-and-air mixtures at overburden depths at which underground coal mining occurs?" A mine depth of 600 ft was selected for this initial study. Computer simulations were performed, with and without the presence of a metal- cased borehole extending from the surface to the mine level. CDEGSTU software from Safe Engineering Services & Technologies, Ltd (SES) was used for the simulation.

By S. J. Page, J. A. Organiscak

Airborne respirable dust surveys were conducted at six surface coal mines to investigate the effectiveness of dust control methods used on rotary rock drills and bulldozers. Dust controls commonly used on drills include a dry dust collection system, exhausting from a shrouded area around the collared hole, and an enclosed drill operator cab, filtering airborne dust from the cab. Bulldozers are also typically equipped with an enclosed operator cab as a dust control measure. Airborne respirable dust sampling was conducted near each equipment's source of generation and inside its enclosed cab. Silica analysis was performed on the dust samples to determine the percent silica content in the dust generated at the six mining operations. An additional eight- month follow-up of dust sampling was also conducted in the enclosed operator cabs of several rock drills and bulldozers. Data were analyzed for long-term variability of accepted control methods to abate dust and silica levels. The highwall rock drill was the major and most variable dust source as compared to the bulldozer, generating dust levels, on average, one order of magnitude higher than dust levels of the bulldozer. Four of the six drills surveyed had dust containment and capture problems at the shrouded drill table above the lple. Repairs or modifications to three of the drill dust collection systems were shown to reduce dust levels by more that 50% next to the shrouded drill table. The enclosed operator cabs provided more than 90% and more than 40% lower dust levels than at the dust source for the drill and bulldozer, respectively. Long-term sampling of several of these highwall drills and bulldozers showed that the dust levels in the drill cabs were frequently higher than 0.2 mg/m3 and more variable than in the bulldozers. The bulldozer dust levels were frequently below 0.2 mg/m). Future research should focus on improving some of the deficiencies present in the drill's primary dust collection system, and developing quality control methods to ensure the integrity of enclosed cab protection for equipment operators.

By N. Kumar Kittusamy, Richard E. Miller

This field study evaluated a newer and older dozer at a construction site. Both dozers performed similar activities in the same location within the construction site. Two operators participated in this study. One operator used the older equipment and the other operator used the newer equipment. Jolting and jarring measurements were taken at the seat/operator interface and at the floor of the cab. The result of this field study indicates that the newer dozer was better than the older dozer.

In 2006, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 These mines (e.g., potash, gypsum, salt) comprised 5.0% of all operations. ? Mines producing common clay comprised 25.2% (n=187) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands.

Jan 1, 2008

By Deborah A. Spotts

Researchers at the Bureau of Mines have developed a technique for re- generating chromic acid-sulfuric acid etching solutions used in metal surface treatment operations. The technique utilizes a diaphragm cell equipped with a cation-selective membrane to oxidize cr3+ to cr6+ at the anode and to remove copper, the major metallic contaminant, at the cathode. Normally, spent etchant is discarded after approximately 3 days of use. Using the electrolytic cell, the etchant can be used for a year without replacement, From data obtained from industrial-scale cells, the installation of a regeneration cell with a 1,000-gal catholyte- holding tank has been estimated to save at least $240 per day, The payback period for the investment is estimated to be about 10 mo or less. Because the magnitude of these cost savings will vary at different locations, several graphs are presented to aid in calculating payback for a specific site. Using these graphs and the capital costs presented in this study, the payback period can be determined for installing a regeneration cell with a 500- or a 1,000-gal catholyte-holding tank in an existing surface treatment plant.

Jan 1, 1983

By R. V. Ramani, P. M. T. White, D. Sutton

3.1 Criteria for Selection A coal deposit has the following major characteristics: i) wide distribution as a flat-lying, thin, bedded deposit ii) stable nature of its major components and ranking characteristics such as carbon, heat content, volatile components, specific gravity, etc. iii) number of constituents and characteristics which under present regulations limit usage, such as content of ash, sulphur, sodium, etc. iv) effect of characteristics of over- and under- lying host rocks including porosity and permeability, lithology and general geology v) low value, high bulk nature. Because of the relative stability of its major components and its low unit price, coal does not require the same attention to detail as do the metal deposits. However, new regulations combined with social pressures make it imperative that more accurate information be made available concerning factors which affect the quality of coal and which may have an adverse effect on the environment when the coal is mined or burnt. The method selected for the evaluation of a coal deposit must, therefore, be flexible and sensitive enough to be used to interpolate stable parameters whose general distribution character-

Jan 1, 1974

This report was limited to a search of available literature on under- ground methods to combat acid water pollution. From this review it is evident that very little work has been done in this specific area. It is also evident that there are specific areas of mining engineering and mining related hydrology and geology that need further research efforts to solve the many water problems. They are: (A) Composition, variation and availability for oxidation of sulfur in strata. (B) Rate of oxidation of sulfuritic materials. (C) In situ limestone and its influence on underground acid drainage. (D) Structural, stratigraphic and hydrologic character of old mining areas as a basis to make decisions about adjacent new mining areas. (E) Operational changes in mining methods to prevent pollution. (F) Sealants for underground coating to exclude water from contact with pyrite to inhibit formation of the contaminants. Such a program has been initiated on refuse piles. The prime purpose of this report is to investigate those practices which have been used to regulate or control water accumulation and prevent harmful mine drainage. A supplemental purpose is to indicate those areas which need further research to prevent underground mine water pollution.

Jan 1, 1970

This bibliography lists publications issued by the Bureau of Mines concerned with investigations on petroleum and natural gas. The items included are chosen for their continuing interest and value. It was recognized early that a list of petroleum and natural gas publications was needed for the Bureau's work, and unofficial publication of a ?straight forward? listing was begun. It was at first a chronological list; however, suggestions submitted by its users prompted a format change to show publications under broad, general topics. Author and subject indexes were developed, becoming more detailed with each new edition. This present list supersedes the ones compiled in 1949, 1952, and 1957, and several supplements, which were aside available to the public by the Library Of the Bureau?s Bartlesville Petroleum Research Center. The unofficial field publication came to be widely known nail in considerable demand by those who are primarily interested in the Bureau's publications on petroleum and natural gas so that it became, desirable to have it published as an Information Circular. It is hoped drat, this official publications will result in a wider and more effective use of the Bureau's research results which are reported in its publications.

Jan 1, 1964

[THIS bibliography lists publications issued by the Bureau of Mines concerned with investigations on petroleum and natural gas. The items included are chosen for their continuing interest and value. It was recognized early that a list of petroleum and natural gas publications was needed for the Bureau's work, and unofficial publication of a ?straight forward listing? was begun. It was at first a chronological list; however, suggestions submitted by its users prompted a formed change to show publications under broad, general topics. Author and subject indexes were developed, becoming more detailed with each new edition. This present list supersedes the ones compiled in 1949, 1952, and 1957, and several supplements, which were aside available to the public by the Library Of the Bureau?s Bartlesville Petroleum Research Center. The unofficial field publication came to be widely known and in considerable demand by those who are primarily interested in the Bureau's publications on petroleum and natural gas so that it became, desirable to have it published as an Information Circular. It is hoped that this official publication will result in a wider and more effective use of the Bureau's research results which are reported in its publications.]

Jan 1, 1964

By H. J. Fissan, G. Ananth, K. Rubow, V. Marple

"INTRODUCTION Over the past several years a new type of cascade impactor that utilizes small nozzle diameters (micro-orifice nozzles) has been under development (Kuhlmey et al., 1981; Marple et al., 1981). The small nozzle dimensions allow for particles to be collected as small as 0.024 µm aerodynamic diameter on the last stage of the impactor. To obtain a reasonable flow rate of 30 I min - i through the impactor, a large number of nozzles (up to 2000) are required per stage.Furthermore, by locating the nozzles of multi-nozzle stages in a prescribed manner (described in detail by Marple et al., 1981) and rotating the impaction plates relative to the nozzle plates, uniform deposits can be achieved on the impaction plates. As described by Marple et al. (1981), the advantages of a uniform deposit impactor over the conventional impactor that collects particles only beneath stationary nozzles are: (1) maximum use of the impaction substrate surface, reducing both particle bounce (if substrates are greased) and tare weights of the substrates (if particle mass is measured gravimetrically); (2) deposited particles can be analyzed for elemental composition by X-ray fluorescence (Dzubay and Rieke!, 1978); and (3) the pressure in the impactor can be kept relatively high compared to low pressure impactors that depend on a large slip correction to achieve small particle collection (some types of particles may evaporate at low pressures). The work described in this paper investigates two additional advantages of a uniform deposit impactor. These are: (1) the possibility of collecting two separate deposits at one time on one stage for two types of analysis techniques, and (2) the possibility of utilizing piezoelectric quartz crystal impaction plates more effectively by eliminating the deposit location sensitivity nature of the crystals (Schulze-Frohlich, 1981 ).MICRO-ORIFICE UNIFORM DEPOSIT IMPACTOR (MOUDI)A photograph of an eight-stage MOUDI is shown in Fig. 1. Each stage body of the impactor supports the impaction plate for the stage above and the nozzle plate for the stage below as shown in Fig. 2. By rotating alternate stage bodies, while holding the other stage bodies stationary, the impaction plates (or nozzle plates) will be rotated relative to the nozzle plates (or impaction plates).Rotation of the alternate stage bodies is achieved by gears on these bodies that mesh with gears on an electrically driven drive shaft of a rotating mechanism (Fig. 1 ). The alternate stage bodies are restrained from rotation by pins that rest on the drive shaft."

Mar 1, 1989

By John Owens, Wayne Howie, Hamid Maleki

After an analysis of the hazards of room-and-pillar retreat mining systems, it became apparent that safety could be significantly improved by considerations of (1) human factors, (2) remotely controlled mobile roof supports (MRS=s), (3) mine layout designs, and (4) ground monitoring systems. Initial studies of the effectiveness of MRS=s focused on their interaction with mine strata and evaluations of suitable measurements for detecting roof stability problems during pillar extraction. These studies indicated that overall stress distributions and strata movement were most influenced by the stiffness of coal-measure rocks and the design of mining layouts. Thus, to improve worker safety, mine layouts should be carefully designed and a pillar extraction method chosen for specific geologic and stress conditions. Pillar failure was often associated with an increase in pressure on the hydraulic gauges of the MRS, and roof failure was often preceded by rapid changes in the rate of roof-floor convergence. These studies led to development of a monitoring system that displays loading rate on an MRS in real time. A major MRS manufacturer cooperated in installing and testing the system on an MRS. New field studies focus on evaluating the performance of the system, measuring roof-floor convergence, and optimizing the safety of MRS operations through proper mine layout design.

By R. V. Ramani, P. M. T. White, D. Sutton

This review of literature is centered around ore evaluation and reserve calculations as generally used in the mining industry. Methods of data interpolation were reviewed with the object of determining a method that would best suit the evaluation of under- ground coal deposits. Further, computerized data library concepts as related to geological data were investigated together with a brief evaluation of the data requirements for the total project. Additionally, computer techniques for the processing of geological data with a view to generate management information for decision making were reviewed including hardware and software availability. 2.1 Interpolation and Extrapolation of Data The importance of accurate estimates of value parameters in terms of their geographical and geological distribution within a, mineralized body has long been recognized in the evaluation of metallic and non-metallic deposits. As the factors which affect mineral distributions and associations are better understood, accuracy, and reliability of estimation increases. The ideal objective is to develop a deterministic model with the capability of accurately predicting the value at any geographical location. The most important value parameters requiring determination in any orebody are the grade and the quantity of ore that can be mined at the stated grade. These two parameters are modified or qualified by others which include physical dimensions and physical and chemical characteristics of the ore value. Therefore, the

Jan 1, 1974

By S. H. Denny

"As the result of the work of an efficient safety organization, the Midwest Refining Co. at its various operations and particularly in the Salt Creek field has been able to show a definite accident reduction. Lost-time accidents during the past year have been reduced to a small number as compared with previous years, and infection cases have been almost eliminated.The accident-prevention work of the Midwest Refining Co. is in charge of the department of industrial relations, with a director as the administrative head; two safety men handle the work directly at Midwest, Wyo. A competent medical staff with a well-equipped hospital at Midwest is also an important factor in the prompt and proper treatment of injured persons when an employee is injured, he is given first-aid and then taken to the hospital with minimum delay.About 1,450 persons are employed in the 4 departments (production, gas, pipe lines, and electrical) and in the 34 districts of the Midwest Refining Co. The work at Midwest spreads over a considerable area, and new drilling operations, pipe work, and similar activities require the services of many small gangs of workers. Complete supervision, of each job, whether shall or large, is possible through the large number of superintendents, foremen, and gang pushers employed; thus, there are 20 superintendents, 78 foremen, and 115 gang pushers. The largest number of men under any one toss is approximately 15, and it is probable that much of the good safety record is due to this intensive supervision. These company officials, including the gang pushers, have been impressed with the idea that it is their duty to see that the men under them do not get hurt; the responsibility of instructing new employees in safety practices is placed directly upon them. Monthly meetings of the field officials, including superintendents, foremen, and gang pushers, and as far as possible the men, of each district are held with the safety engineer. Both officials and men are encouraged to bring up for discussion any practice or proposals looking to the changing of any conditions that will"

Apr 1, 1928

By A. Wahab Khair

"This paper deals with the description of the capabilities of a unique rotary coal cutting simulator which has been designed and fabricated at West Virginia University. It operates under the simulated mining conditions with in-situ stresses (horizontal and vertical stresses) being applied to a coal block of 18 in. x 15 in . x 6 in located in a suitably designed confining chamber. Cutting drum rotation can be varied from 1 to 40 rpm with the capability of stopping the drum after a predetermined number of rotations. Tests can be performed with four different bit angles, 15, 30, 45 and 60 degrees . A maximum of seven bits could be used in seven different orbits. Various cutting depths up to a maximum of 4 in. is possible.Monitoring devices constitute, Linear Variable Differential Transformers (LVDTs), pressure transducers, cascade Impactors, flow meters, flow controls and drum cutting speed. LVDTs are used to monitor the displacement of the coal block as well as the depth of cut. Pressure transducers are used to monitor the changes in pressure, both due to the thrust and due, to the intermittent cutting nature of the rotary cutting. Flow controls will be used to run the drum at a set rpm between 1 and 40 and to provide a different rate of advance. All the above mentioned devices can be operated and monitored by a fully automated control system. Six-stage cascade impactors are used to determine the mass distribution of dust along the rotation path of the drum. The fracture size, shape and Intensity can be studied by optical microscopy and the dust entrainment by using high speed photography.This equipment will basically be used to study the fracture mechanism in coal, associated with operating and in-situ parameters and further relate It to dust generation and entrainment In underground coal mines."

Jan 1, 1988

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962

By Ronald S. Conti

This is the fourth and final article in a series that discusses underground fire-fighting preparedness. As with the previous three articles, it is based on interviews with 214 miners at 7 underground coal mines (referred to as Mines ?A? through ?G?) conducted by researchers of the National Institute for Occupational Safety and Health?s(NIOSH) Pittsburgh Research Center[Vaught et al. 1996]. The first article presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. The third article described miners? experiences in fighting underground mine fires and presented their perceptions of training and readiness for fire-fighting. This final article in the series offers suggestions to improve mine fire-fighting preparedness.

Jan 1, 1997

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. DATA INPUT FOR THE OPERATING PROTOTYPE [To run the Rail Haulage Model independent of the Production Sub-system, remove the production data from card type four through the blank card following END DATA on page B18 and change the fourth data element under ADDITIONAL DATA from 1 To 0.]

Jan 1, 1974

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

Engineering controls for overburden drilling include dry dust collection systems, wet dust suppression systems, and enclosed cabs [Zimmer and Lueck 1986; Volkwein et al. 1979]. Proper maintenance of the dust suppression system is critically important for drills using dry dust suppression methods. Failure to rigorously maintain these systems will result in inadequate dust control. Acute silicosis has been reported in miners operating equipment that relies on dry dust suppression [NOSH 1992].

Jan 1, 1997