Search Documents

The National Institute for Occupational Safety and Health (NIOSH) recommends that occupational exposures to respirable coal mine dust and respirable crystalline silica* be controlled by complying with the provisions presented in this document. These recommendations are designed to protect the health and provide for the safety of workers exposed to respirable coal mine dust and respirable crystalline silica for up to 10 hr/day during a 40-hr workweek over a working lifetime. The information presented in this document demonstrates that underground and surface coal miners are at risk of developing simple coal workers' pneumoconiosis (CWP), progressive massive fibrosis (PMF), silicosis, and chronic obstructive pulmonary disease (COPD). Adherence to the recommendations in this document should prevent or greatly reduce the risk of adverse health effects in workers exposed to respirable coal mine dust and respirable crystalline silica. NIOSH recommends that preventive efforts be focused primarily on reducing worker exposures. Effective health and hazard surveillance and medical screening are also useful components of a comprehensive prevention effort.

Jan 1, 1997

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

Provide the technology to remotely control a thin¬-seam continuous mining machine from a safe location hundreds of feet outby the working face in an underground room-and-pillar mine. Background and Approach Hard-wired or radio remote control of continuous mining machine has been commercially available since the early 1970's. This type of remote control, in low and high coal seams, situates the machine operator offboard, but within direct view of the underground coal face, Although positioned under supported roof, the operator can still be exposed to face area hazards that include roof-rib falls, dust, methane explosions, and equipment congestion. The U.S. Bureau of Mines approach has been to put the operator into a protected compartment at a location away from the working face. Since 1979, the Bureau has investigated innovative methods to better protect face area workers in under¬ground room-and-pillar mines. In 1989, the Bureau demonstrated an offboard, computer-based remote con¬trol system in a West Virginia highwall mining operation that stationed the operator hundreds of feet away from the working face. In late 1992, much of this technology, plus improvements, Was used to demonstrate, on the surface, how a thin-scam continuous mining machine could be remotely controlled 200 feet from the machine in a 36-inch working height.

Jan 1, 1992

By Terry J. Close

In 1992, as part of the U.S. Bureau of Mines Idaho Land Assessment Program, the Western Field Operations Center investigated the mineral resources of the 30,300-hectare Elk Summit study area. The area is in the Clearwater National Forest, adjoining the Selway-Bitterroot Wilderness in Idaho County. Idaho. The study area is underlain by granitic and metasedimentary rocks. Associated with these rocks are road metal (stone) resources, black sand mineral placer resources, and thermal water resources. Also present are abundant sand and gravel. Two of the five sites examined during the Bureau study have road metal (stone) resources, one has black sand mineral resources, one has thermal water resources. The fifth site is a black sand mineral placer occurrence. There is no evidence of petroleum or coal resources. Idaho County records indicate that 38 mining claims, mostly black-sand placer, have been located in the study area, Twenty-three of the claims are current. Workings consist of a few pits and trenches at the placer, and two borrow pits. The only mineral commodity produced from the area was about 1,500 tonnes of stone excavated from the Savage Pass and Swamp Creek borrow pits along the Elk Summit road, north of Hoodoo Lake. The stone was used to surface the road; these stone resources will continue to be used as needed.

Jan 1, 1993

By Peter F. R. Altounyan, Paul B. Cartwright, John W. Cassie

This paper describes measured data on strata behavior obtained in recent years from sites in the United Kingdom and the implications for pillar design. The data include results from overcoring stress measurements adjacent to coal mine roadways and deformation monitoring related to longwall extraction. The stresses adjacent to mine roadways or entries have been measured at a number of coal mine sites in the United Kingdom. The results are analyzed with regard to the information they provide on pillar behavior and strength estimates. A reduction in stress consistent with yielding of the strata adjacent to the roadways is evident. This is consistent with the confined core model for pillar behavior. The pillar strength is dependent on the rate atwhich vertical stress can increase with distance from the pillar edge and hence the confinement provided to the yielded material. The measured data indicate a wide range in pillar strengths. Two groups of results are identified that show significantly different behavior corresponding to differing effective pillar strengths. Estimates of pillar strengths derived from the measured data for these two groups are compared with established equations used for pillar design. The differing behaviors and strengths are attributed to variations in the amount of yielding and deformation in roof and floor strata and hence in the amount of confinement they provide to the coal seam. Numerical modeling is used to provide a comparison with the measured data and to indicate that this provides a feasible mechanism to account for the measured data. As the depth of mining increases, pillars tend to become increasingly wide and squat. In such cases, it is possible for the surrounding roadways to become badly deformed and damaged while the pillars remain stable. The criteria of comparing pillar strengths and loads to establish pillar stability become less applicable in these circumstances; rather, considerations of roadway stability may be the limiting factor in determining suitable pillar dimensions. This is the case for pillar dimensions typically employed around longwall panels in the United Kingdom. Depending on the properties of the site and what are deemed to be satisfactory roadway conditions, this can lead to wide variations in required pillar dimensions. Measured data for deformations in roadways influenced by adjoining longwall workings are presented. These show that in some circumstances the influence of longwall extraction can be transmitted over large distances and confirm the variability in required pillar sizes depending on site properties.

Jan 5, 1999

By Oleg Terichow

Electrophoretic mobility measurements were made by the Bureau of Mines on samples of a Florida phosphate slime to determine the optimum conditions of coagulation and settling in an aluminum sulfate solution. Addition of anthracite to promote mutual coagulation demonstrated the practicability of heterocoagulation by reduction of the repulsive effect of double layers. By proper selection of the electrolyte and its concentration, the reduction of the double layers to a net zero point of charge causes the predominance of Van der Waals' forces of attraction leading to the coagulation and rapid settling of both particle systems, as is predicted by the Derjaguin-Landau-Verwey-Overbeek theory of colloidal stability. Confirmation was found in the microfiltration tests where a modified Carman equation was applied to evaluate the specific filter bed resistance.

Jan 1, 1975

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high- expansion foam generator. Thus allows fire-fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

Lower the respirable dust exposure of longwall shearer operators with improved water spray systems on the shearer. Approach Orient sprays (rather than relocate them) so that dust is held against the face. How It Works Research by the Bureau has indicated that shearer operator dust levels depend largely on how fast dust from the upwind drum spreads into the walkway. Water sprays on the shearer body can greatly affect the spreading of this dust because each spray moves air like a small fan, generating strong cross-currents of air around the shearer. Poorly designed spray systems, especially those with nozzles pointing upwind, will stir up much more dust than they sup-press. On the other hand, Improved systems may be designed to hold the dust cloud against the face while also suppressing It. In such arrangements the water is sprayed downwind and used with screens made from conveyor belting.

Jan 1, 1981

By R. J. Matetic, D. Elsworth

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the field site. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 1995

By Amanda Azman, Richard Hi Danie/son

Ultimately, the most important product of a hearing conservation program is the prevention of hearing loss, not the amount of hearing protection that has been purchased or whether employees are attending their annual training sessions. Audiometric testing directly reveals whether hearing losses are actually occurring in a plant. With audiometric data, we can assess overall program effectiveness, alert workers of impending hearing loss, and reveal potential employer liabilities for compensable hearing loss. Without the ability to efficiently analyze audiometric data or produce effective reports, our programs become fruitless and unproductive. Consequently, ifaudiometric data are such vital end-products, then effective audiometric technologies serve as the prime architect and generator of these fundamental data. These technologies, consisting ofaudiometers, associated peripheral hardware, and database/reporting software, deserve our consideration.

By Thomas P. Mucho, William D. Monaghan, John Wood, Michael A. Trevits

We have tested the ability of ground penetrating radar (GPR) to resolve adjacent mine workings. The work was conducted at two National Institute for Occupational Safety and Health locations – an underground coal mine and an underground limestone mine. The objective of our work was to determine if GPR signals could be received from distant mine workings. The GPR system was calibrated on underground mine pillars of known dimensions using a variety of antennas. The system was then tested at several underground locations in an effort to detect an adjacent drift entry; and an adjacent abandoned coal mine. As a means of verification, an in-seam horizontal hole was drilled from the active coal mine to the abandoned mine to confirm the presence and location of the abandoned mine workings. Our results show that in the case of the limestone mine the maximum depth of penetration where the mine workings could be resolved was 85 ft; and in the case of the coal mine the abandoned mine workings could be resolved at a depth of 205 ft. We conclude that it may be possible to utilize GPR for initial underground mine studies followed by directional drilling to accurately delineate the extent and position of adjacent abandoned mine workings.

By H. Robert Ensminger

As a result of the new mining law implemented in August 1985 and the programs conducted by the Institute Ecustoriano de Mineria (INEMIN), which was created by this legislation, there was considerably greater activity in the nonfuels mineral sector during 1986. Over the next 2 years, INEMIN will be developing a national mining plan that will guide Ecuadorean mineral development for the balance of this century. As stage one of INEMIN's mineral study, historical records were reviewed and 300 abandoned mines and 1,200 unexplored mineral deposits were available for further investigation. In 1986, INEMIN established 5 branch offices and negotiated 250 new mining contracts with foreign companies valued at $16 million. Despite all this activity, INEMIN officials estimate that 100,000 square kilometers remain available for claim staking. Technical assistance contracts were signed with Belgium, the Federal Republic of Germany, Italy, Spain, and the United Kingdom, to assist in a variety of assignments ranging from helping prepare the national minion plan to the development of industrial mineral deposits.

Jan 1, 1988

By Oliver Bowles

As the preface states, this bulletin is the fourth of a series of re- ports by the Bureau of Mines on different phases of quarrying in the United States. The first part of the bulletin describes the chief types of cements, the growth of the cement industry in this country, and the character of the raw materials used. The bulk of the report deals with quarrying methods and equipment, and gives especial attention to drilling and blasting; a chapter on rock mining and one on pros- pecting are included. Methods of manufacture are mentioned briefly, as that subject, except as related to quarrying, lies outside the scope of this report; but transportation methods and the effects of the man- ner of mixing the materials at the quarry or crushing plant on quarrying methods are discussed.

Jan 1, 1918

By Eugene T. Sheridan

This report presents statistical data on individual plants in the fuel- briquet and packaged-fuel industries circularized by the Bureau of Mines, United States Department of the Interior, in its 1957 annual survey. This survey revealed that 17 briquet and 23 packaged-fuel plants were active part or throughout the year. The annual production capacity of the fuel-briquet industry was 3,088,000 net tons, a decrease of 17 percent from 1956. The decline in capacity was caused in part by the permanent retirement of 4 plants and also by the reduction in capacities of 4 other plants. The rate of production of briquet plants also decreased as the industry operated at 35.8 percent of capacity compared with 40.9 percent in 1956. Every operating plant in 1957 had an annual capacity exceeding 25,000 tons.

Jan 1, 1958

By M. J. Kovalik

The effects of the process variables on the production of chemical coke on a chain grate stoker, a type of traveling grate, were studied. Six bituminous coals, ranging in volatile matter from 16.7 to 43.8 percent, were successfully carbonized, yielding chemical coke with acceptable physical properties. The coke yields were dependent on the volatile-matter content of the coal. The air fuel ratio had the most marked effect on the yield and characteristics of the resultant coke, and the general furnace performance. Results can only be predicted; the actual yield and quality of coke obtained from any given coal can only be determined by actual tests using the optimum processing variables to obtain a coke with minimum volatile-matter content and to retain as much of the fixed carbon in the original coal as possible.

Jan 1, 1967

By Arne Landsberg

Experiments were made with a batch reactor to determine the effect of gas pressures, temperature, and gamma radiation intensity on the reaction CO + Ch ? COC12. The equation, [dp = 0.0110 (1 - 0.01t) (PCOI)1/2 PC12] where [dP] is the change of pressure of phosgene with time (atm/hr), t is the temperature (°C), PCO and PC12 are the reactant pressures (atm), and I is the radiation intensity (r/hr), was found to best fit the data. Oxygen and a large ratio of reactor surface to volume retarded the reaction, but inert gases had no effect. A low-temperature reactor system is proposed to take advantage of the conditions which give a high reaction rate with gamma radiation and a simple scheme of product purification.

Jan 1, 1970

By Launa G. Mallett, Robert H. Peters, Barbara Fotta

Due to variations in the thickness of U.S. coal seams, there is great variability in the height of the roof where underground miners work. Restrictions imposed by low seam heights have important safety consequences. As the height of their workplace decreases, miners must stoop, duck walk, or crawl, and their vision, posture, and mobility become increasingly restricted. Low seam height also places important restrictions on the design of mobile equipment and other mining machinery. Using the employment and injury data reported to the Mine Safety and Health Administration (MSHA) from 1990 to 19% small underground bituminous coal mines with less than 50 employees were stratified by average coal seam height according to the following categories: low (? 42"), medium (43"60N), and high (? 61"). Injury rates for both nonfatal days lost and fatality cases were examined by seam height and leading type of injury incidents. The leading types of Incidents associated with fatalities were roof falls and powered haulage equipment. In comparison to high-seam mines, miners working in low or medium seams are at higher risk of being killed by powered haulage equipment, roof bolting machines, and falls of unsupported roof. The leading types of incidents associated with nonfatal injuries were handling materials and powered haulage. As mining height decreases, miners are at increasingly higher risk of having a nonfatal injury from incidents involving roof bolting machines, load-haul-dump equipment, personnel carriers, and powered haulage conveyors. As mining height increases, miners are at increasingly higher risk of having a nonfatal injury from slips and falls and incidents involving shuttle cars and roof and rib falls. Knee injuries are a particularly severe problem in low- seam mines. The rate of injuries to miners while crawling or kneeling is 10 times higher in low seams than in high seams

By K. L. Rubow

"Diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and as found in five underground coal mines- 3 utiliting diesel-powered hallage equipment and two electric-powered equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations. The first technique, using a microbrifke uniform deposit impactor CMOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of .the aerosol is predom1nately submicrometer and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance CCMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results. ,The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral ·dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 um. For the diesel equipped mines, this analysts yielded an average value for the fraction of the fine aerosol attributable to mineral dust of 1 pct. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling."

Jan 1, 1988

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of-combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were conducted in a 1 80 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.13, and 0.06 m/s were determined at 30.60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

By D. Harrington

In general, mining is carried on underground, that is, in confined places where it is difficult to obtain adequate lighting and frequently in rock strata requiring much care to prevent caving. Moreover, explosives must be used in mining with the numerous hazards associated with them, and some mines give off explosive or irrespirable gases; also, ma- chinery must be used, usually under conditions much more hazardous than on the surface. These and many other considerations cause mining to be probably the most hazardous occupation in which large numbers of our fellow countrymen are employed. Prevention of accidents in the mining industry is far more complicated than in surface industrial work, even of the more hazardous types, because the different elements that enter into possible accident occurrence are ascertained more readily above ground and suitable action can be taken against them; moreover, errors in connection with prevention of accidents in surface industrial work usually affect only one or, possibly, a few persons, while in zines one human error may readily cause an explosion or other untoward occurrence resulting in the death of scores or even hundreds of persons. This difficulty in the prevention of accidents in and around mines is well-known, and most countries and States have regulations to guard the safety and, to a much smaller extent, the health of workers in mining and allied industries. In general, the State laws and regu- lations regarding the welfare of mine workers are merely a skeletonized outline of some more or less fundamental minimum requirements and are far too general to do much more than suggest some procedure which may or may not be safe or healthful. Most of them are grotesquely out-of-date as applied to present-day conditions, and none of them is adequate to protect life, limb, health, or property. Unquestionably, there is great need for a closer correlation of the laws and regulations of the various States with regard to safety in the mining and allied industries, and while mining conditions vary far too much for a standardized mine safety law applicable to all of the States, on the other hand there are numerous standard and fairly fundamental safety pro- visions which apply to all mines and which should be embodied in the mining codes of all States. Undoubtedly, these standardized safety requirements would be opposed by a consider- able part of the industry, but the ultimate effect would be beneficial to the owners, work- ers, and the general public. For many years progressive mining companies in the United States have not been satisfied to operate only within the meager safety requirements of the State laws or regulations and have adopted additional and far more effective safety procedure of their own, although com- plying also with the State laws and regulations. As a result of this forward-locking policy, zany of these companies have made astonishing progress in the reduction of accidents.

Dec 1, 1935