Search Documents

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today's coal preparation industry.

Jan 1, 1977

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By R. E. Peterson

The Bureau of Mines has undertaken beneficiation investigations on samples representing large tonnages of oxidized taconites in order to develop and evaluate applicable technologies for producing iron oxide concentrates from these materials. Information derived from the investigations can be used to expand the domestic iron raw-materials base and to establish the impact these taconite deposits may have on future national iron ore requirements. This report describes a process that includes reduction roasting, magnetic separation, and flotation, applied to a western Mesabi Range sample taken near Coleraine, Minn. The sample contained 36.8 pct iron and 46.0 pct silica, and represented 0.5 to 1 billion tons of crude material. An average of 962 lb/hr of oxidized taconite was roasted with 33 lb/hr of lignite in a 35-foot-long rotary kiln. Pulverized lignite and natural gas maintained the kiln operating temperature at 850° C. The roasted taconite was beneficiated by magnetic separation and cationic flotation in a 900-lb/hr pilot plant and yielded a product analyzing 68.1 pct iron and 4.6 pct silica, and containing 82.4 pct of the iron in the kiln feed.

Jan 1, 1981

By Robert L. Lagace

The attention of this group was focussed on four through-the-earth communication systems that are presently of high interest to the U.S. Bureau of Mines; four systems for providing operational/emergency communications on the working sections of coal mines, indeed up to the very face of the section. The systems are: uplink-data, downlink-voice, sidelink-call alert coded page, sidelink-roof bolt voice page. Each of these systems makes use of the mine overburden as the signal transmission medium, as opposed to the guiding wires, cables, and tunnels treated by the operational communications working group. Each of these systems satisfies one or more of the Bureau's objectives for mine communications systems; namely • reliable links for monitoring the mine environment under both operational and emergency conditions. • reliable links for communicating with miners during emergencies. • special links for increasing the efficiency of day-to-day operations of the mine. Each of these systems has been successfully demonstrated on a limited experimental basis, and prototypes of all these systems are installed and operating in the USBM experimental mine in Bruceton, Pa. Each of these systems must now be optimized regarding its performance, and engineered for practical routine application to the working sections of actual operating coal mines, particularly those of the room and pillar type. This optimization and engineering must take place subject to the principal constraints listed by Howard E. Parkinson in his Workshop paper entitled, "Objectives and Constraints of Through-the-Earth Electromagnetic Communications Systems'' and enumerated below. • Depth of Mine Overburden • Overburden Conductivity • Electromagnetic Noise In and Above Mines • Limited In-Mine Electrical Energy (Stationary or Man Carried) During an Emergency • Intrinsic Safety for In-Mine Equipment • Practical and Rugged Equipment for Use Under Both operational/Emergency conditions • Severe Weight Limitations for Man Carried Equipment • Reasonably Low Costs Especially for Man Carried Equipment Part II of this paper provides a brief description of each system, while Part III summarizes the present status of developments related to these systems and some recommendations for future work needed to advance these systems to the practical application stage.

Jan 1, 1973

By Russell. Paul L.

"INTRODUCTION Preliminary reports by Bureau of Mines engineers 3/ and by the Federal Geological Survey 4/ suggested that exploration would discover substantial reserves of minable ore in the Contact mine, Grant County, New Mexico. During February and March 1943, a sampling program was conducted on this property under the direction of the author. This was art of a general survey of the manganese districts of southwestern New Mexico.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as practicable soon as after its conclusion. The Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocer, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. S. Dean, assistant director. With respect to this report, special acknowledgment is due to C. H. Johnson, district engineer for New Mexico, and E. D. Gardner, regional engineer, and his staff, of the Central Region of the Bureau of Mines at the time of this work in 1943; also to Kenworthy, metallurgist at the Rolla. Mo., Laboratory of the Bureau of Mines, for work on beneficietion of the ore, and Sherman K. Neuschel, geologist of the Federal Geological Survey, for assistance in interpreting geological data at the project."

Oct 1, 1946

By Wilbur I. Duvall

In a previous report, entitled A Gage and Recording Equipment for Measuring Dynamic Strain in Rock, a control circuit for a drum camera was described. The purpose of this control circuit was to provide a means for firing seismic caps, synchronizing the firing of the cap with the opening of the camera shutters and generating an electrical impulse at the instant of detonation. The operation of this circuit depended on the following two characteristics of seismic caps: (1) these caps contain a bridge, which breaks at the instant of detonation, and, the firing delay time of the cap is a function of the firing current. During the course of the Bureau's studies, considerable difficulty was experienced from "firing hash", i.e., spurious vibrations that appeared on the records at the time of detonation. The cause of most of this "firing hash" was traced to the intermittent grounding of the cap leads at the time of detonation. As the cap leads were still connected to the firing battery, the grounding of the leads permitted current to flow through the rock to the gage and to return to the firing battery through the shield on the gage cables. The intermittent flow of current along the cable shield produced potentials on the gage leads that were recorded as the "firing hash." To eliminate this difficulty, it is necessary to remove the firing voltage from the cap leads the instant the cap detonates. This report supplements the previous report and describes an improved circuit that can be used to fire seismic caps, remove the firing voltage from the cap leads the instant the cap fires, control the firing delay time in the cap, and generate reference signals at the time current starts flowing in the cap circuit and at the time the cap detonates. These reference signals can be used to determine the firing delay time of seismic caps and the time at which the seismic wave is generated by the explosion.

Jan 1, 1950

By R. M. Gammell

"INTRODUCTION The Farmer prospect was examined by W. R. Green, an engineer of the Bureau of Mines, in June 1944. As a result, studies of this property were included in a general preliminary investigation of the Etevens County lead-zinc deposits by the Bureau in 1945. The exploratory work was designed chiefly to supplement the surface examination by determining the nature of the mineralization below the zone of oxidization. The results of the small-scale diamond-drilling program undertaken at the property are presented in the following report.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization our resources to the end that they make the greatest possible contribution to security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work and prepares the filial report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Mar 1, 1947

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

By W. M. Dressel

A simple field test for detecting the presence of germanium in rocks, coals, and flue dust has been developed by the Bureau of Mines. The method consists of dissolving germanium from the samples by either acid or fusion treatment methods, adding a few drops of hematein or phenylfluorone dye, and extracting the resulting colored complex with carbon tetrachloride. INTRODUCTION Germanium is obtained commercially as a byproduct of zinc production, as a coproduct of base-metal refining from germanium-bearing mineral, and as a recovered product from the ash of some coals. The growing use of germanium in the electronics industry has increased demand for this semiconducting metal to the extent that an intensive search for new sources of supply is necessary.

Jan 1, 1962

Develop personal computer (PC) based software for analyzing and/or filtering time- and frequency-domain attributes of seismic and electromagnetic signals from geophysical surveys for the enhanced interpretation of rock masses and subsurface geologic structure. The Problem Both mining and petroleum geophysicists utilize seismic signals to characterize rock masses for delineating subsurface stratigraphy and structural conditions. However, a vast amount of information available in seismic project evaluation data often is unavailable for interpretation unless these data are enhanced. New processing technology increases the quality of these signals for analysis and interpretation. Comprehensive signal processing software is mostly written for petroleum exploration companies. Commercially available signal processing programs are often limited to a single application or are restricted for use with specific hardware, e.g., a digital oscilloscope or a mainframe computer. The programs may use computer codes that are proprietary, restrict user modification to expand capabilities, or may be hard to interface. They may have insufficient documentation for easy use and be support dependent.

Jan 1, 1990

By T. Whitrnoyer, J. Sneckenberger

"The acOustic impedances of seven rat lungs were measured at frequencies between 100 and 6400 Hz. Rats were divided into two groups: a silica exposed group (N=3) and a control group (N=4). The silica exposed group was injected intratracheally with silica solution. Three of the control group were intratracheallyinjected with saline. Between four and six weeks after theinjections, all lungs were excised and degassed. Lungs were,suspended in a pressure Chamber, with the trachea canula attached to the end Of a tapered impedance tube. The lungs were subjected to transpulmonary pressures between -30 cm H2O and 6 cm H2O to simulate deflation and inflation. With transpulmonary pressure being held constant, the impedance tube was excited with random noise. A dual channel analyzer calculated H12(f), the transfer function between the two microphones. This function was used to calculate the lung's impedance at that pressure. The impedance magnitude spectra of both groups typically had peaks at 2000,3500, and 5500 Hz. Statistically significant differences. (90%confidence level or greater) between the two groups occur at the 3500 Hz peak at transpulmonary pressures of 20, 8, 6, 4, and 2 cm of H2O. This fact seems to confirm that this method can detect. lung disease. Further research will indicate whether this method will be able to detect the onset Of coal worker's pneumoconiosis.INTRODUCTIONOne of the first studies of impedance Of the human lung were conducted by DuBois et al.[2] using the forced OscillatiOn technique. This technique, however, was limited to frequencies below 30 Hz. Further studies by Van Den Berg [6] revealed thatthe lung reflected higher frequency sounds (100-10,000 Hz), instead Of behaving as an anechoic termination. This discovery has lead to several studies of the acoustical properties of both human and animal lungs at high frequencies [3,4,5]."

Jan 1, 1988

Analyze variably saturated flow in mining and other environmentally sensitive settings through the use of personal computer (PC) based software. The Problem There is an increasing need for mining companies to quantify water contaminants and their migration in the unsaturated zone. New and innovative computer models are therefore necessary to more accurately assess the potential impact of mining activities on groundwater resources and the environment. Applications for unsaturated flow modeling include (1) assessment of the impact of surface or underground extraction mining on flow conditions; (2) assessment of various hydrologic designs for resource recovery, such as in heap leaching or in situ leach mining; (3) assessment of the transport of conservative nonrcactive constituents in response to migration from spoil piles, or acid mine drainage; and (4) assessment of any combination of the above to facilitate expeditious permitting for mining operations. Since the mid 1970's there has been a proliferation of mathematical models and procedures for solving unsaturated now problems; however, few of these approaches have been integrated into software for public use. Commercially available unsaturated flow software models typically are limited to a single application and have restricted approaches. For example, computer codes that solve the unsaturated flow problem based on an analytic expression arc restricted to a simple geometric shape, homogeneous and isotropic materials, and provide only information regarding pressure and flow conditions in specified wells. The variably saturated computer codes that take advantage of the finite difference or finite element approach arc often restricted to either steady state or transient solutions; utilize one specific moisture-retention relationship and moisture-dependent permeability function; do not account for hysteresis; and are used with specific hardware such as a mainframe or work station. This restricts their use because they arc hard to interface, and arc often poorly documented, support dependent, and expensive. The mining community needs a flexible, more broadly based, variably saturated fluid flow simulator for the PC-platform to more accurately predict fluid movement in the mining environment.

Jan 1, 1991

By Robert F. Chaken

The National Institute of Occupational Safety and Health (NIOSH) is dedicated to achieving "safety and health at work for all people -- through research and prevention." An important procedure in pursuing this goal is the NIOSH surveillance studies where the number of injuries are monitored according to demographic, employment, and injury characteristics. These numeric data are then used to identify injury risk factors, develop safety programs, and monitor implemented remediation methods. In essence, ongoing surveillance data form the bases for directing the resources of NIOSH in setting of research and prevention priorities, and in evaluating safety procedures. This surveillance techmque, which is based on the Public Health Service approach to identification and control of disease (1, 2, has been used quite successfully in dealing with relatively high number injuries such as hearing loss, musculoskeletal disorder, respiratory disorder, falls, etc. (2). However a problem arises when extending this paradigm to lower frequency traumatic events; particularly those often referred to as disasters (i.e., high impact events like mine explosions, airplane crashes, etc.). One can ask the question - there hasn't been a coal mine fire fatality in the U.S. for over ten years, to what extent should we be concerned with mine fire safety (resource-wise)? - The National Traumatic Occupational Fatalities (NTOF) system (4J which NIOSH uses to survey occupational fatalities annually, would suggest that underground mine fires would not be a high priority item in occupational safety. Yet, miners' (i.e., the exposed workers) do consider mine fires and explosions to be major safety concerns. I believe that we need to rethink our evaluation of work place disasters, what is worker exposure, and what are the underlying assumptions (both explicit and implicit) as to the impact that economic, societal and degree of hazard factors make on risk evaluation. The answers to all these problems, will require much broader considerations than those in current surveillance safety and health models. This paper discusses some facets of those considerations.

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

By Richard J. Mainiero

The Bureau of Mines has developed a prototype nonincendive explosive rock-breaker charge that can be fired unconfined in underground bituminous coal mines without the danger of igniting a flammable atmosphere that might be present. At present, unconfined shooting in underground coal mines is prohibited, but there are situations where the use of such shots would yield an overall improvement in safety. The charge consists of 1-1/2 lb of permissible water gel explosive in the form of a short cylinder 7 inches in diameter and 7/8 inches high, surrounded by a 1 1/2-inch-thick layer of damp salt, and encased in latex rubber reinforced with cheese cloth. The latex rubber housing provides a charge package that is strong enough to resist rough handling yet is pliable enough to conform to an irregular stone surface. A charge of this shape was found to be more effective at breaking rock than charges with lined or unlined cavities. Incendivity tests in a gallery have shown that the prototype charge will not ignite a flammable methane-air atmosphere when fired. Rock- breaking tests made with limestone boulders indicate that the charge will satisfactorily break stone slabs weighing 1 to 2 tons, and that two or more charges might be effective for slabs weighing up to 10 tons. In cooperation with the Mine Safety and Health Administration (MSHA), a test protocol for the certification of these charges as "permissible" for use in flammable atmospheres is being developed.

Jan 1, 1982

Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During 1996-99, 44 coal miners lost their lives in rock falls, and nearly 2,400 were injured. In addition, nearly 6,000 noninjury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH). The purpose of these proceedings is to provide the mining community with a comprehensive survey of coal mine roof supports. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, this volume describes what types of support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, material handling considerations, and longwall mining through recovery rooms. This proceedings volume also contains information on several important new technologies, which are described here for the first time: •Guidelines for selecting roof bolt length, pattern, and capacity that were derived from statistical analysis of the roof fall experience at 37 underground mines; •A new design method for longwall tailgate supports; and •A technique for measuring loads developed within cable bolts. The papers in these proceedings were presented at open industry briefings conducted by NIOSH on New Technology for Coal Mine Roof Support. The briefings were held in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. The papers were also presented at the Mine Safety and Health Administration (MSHA) Preventative Roof-Rib Outreach Program (PROP) Seminar, which was held at the National Mine Health and Safety Academy near Beckley, WV.

Jan 10, 2000

By Christopher Mark, Anthony T. Iannacchione

Falls of ground continue to be one of the most serious causes of injury to U.S. miners. Of the 256 fatal injuries that occurred in mining between 1996 and 1998, 59 (23%) were caused by falls of ground (Table 23.1). Falls of ground affect some sectors of the mining industry more severely than others. For instance, nearly 40% of the 98 coal mine fatalities between 1996 and 1998 were caused by falls of ground. Underground miners are at much greater risk than surface miners. Nearly half (45 out of 101) of underground mine fatalities were attributed to roof, rib, and face falls, while only 6% of the 155 surface fatalities were caused by falls of highwalls or slopes. The goal of this chapter is to provide guidance to safety professionals tasked with preventing ground fall injuries. This chapter combines an analysis of the Mine Safety and Health Administration's (MS HA) accident and injury data with a survey of industry "best practices" to safeguard miners from ground falls. Ultimately, this approach can help to form the basis of a sound, proactive ground control program for the mining industry. SOURCES OF DATA All the injury data examined in this study were derived from MSHA's fatal investigation reports and the MSHA accident database. Because falls of ground often result in serious injury, MSHA "Fatalgrams" and fatal investigation reports provide a useful snapshot of ground control issues in the mining industry. These reports are available to the public (on the M FHA Web site at www.msha.gov). Fatalgrams, are one-page summaries that are usually published within a month of an accident. They contain very basic information about the accident with a graphic and a short section on relevant best practices. Fatal investigation reports are the official accident investigation reports filed by MSHA personnel. These reports contain general information about the mine, a, description of the accident, physical factors involved in the accident, a conclusion, and enforcement actions, Enforcement actions typically identify citations and discuss violations to the Federal Mining Law. MSHA also maintains comprehensive statistical data on the mining industry's accident and injury record. The law requires that mines file a report on every reportable accident that occurs, containing information on the accident's location, severity, classification, activity, and nature of injury A short narrative is generally included as well. Accident reports can be searched by many of the above fields.

Increase the recycling of critical and strategic materials by simplifying the indentification and segregation of scrap. Background Because the United States is dl-most totally dependent on imports of such critical metals as chromium, cobalt and nickel, Bureau of Mines research has been directed towards conserving these metals by increasing the recycling of the complex scrap materials that contain them. Experienced scrap sorters, using the traditional techniques of object recognition, spark tests, chemical spot tests, color, apparent density, and magnetic properties, can adequately sort a wide variety of alloy groups. However, the complex nature of new materials entering the scrap market has made sorting both more difficult and more important. Some new alloys contain so many components that separation by discrete alloys becomes a prerequisite for effective recycling. The Bureau has completed Investigations on two methods for rapidly sorting complex scrap mixtures. One method uses a combination of two low-cost instruments. The other uses a single sorting instrument. Both approaches are reported.

Jan 1, 1986