Search Documents

By P. Kovalchik, S. Peng, G. Cole, R. Matetic

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90 percent of coal miners and 49 percent of metal/nonmetal miners had a hearing impairment by age 50 (Franks, 1997). Mine workers are exposed to additional noise levels underground due to the reflection of machine-generated noise that would otherwise dissipate in an aboveground setting. Determining the sound-absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed rather than being reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes a finite room, a diffuse field and a relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper presents a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients are essential for determining and predicting potential overexposure to machine operators in different mine environments.1

By F. S. Crawford

This report deals with the effectiveness and economy of installing mine timbers treated with preservatives in long-life service locations. Early in the present century, when mine timbers and labor were plentiful, it was not general practice to install treated timbers in such places. Because national sources of good mine timber are declining steadily, the mining industry must now conserve timber. Moreover, the cost of installing and replacing mine timbers has been rising. Therefore, even the simplest of treatments can be expected to give some return on the investment when applied to timbers that are to be installed in relatively permanent locations. Better methods of treatment will produce better returns. In a service test of maple timbers treated by the hot-and cold-bath method and installed in main haulageways of the Athens mine of the Cleveland Cliffs Iron Co., Negaunee, Mich., zinc chloride-treated timbers had an average useful life of 13.3 years; borax-treated timbers, 11.2 years; and sodium fluoride-treated timbers, 7.7 years. Untreated timbers used as controls had an average useful life of 3.8 years.

Jan 1, 1950

By Harry W. Campbell

U.S. Bureau of Mines investigation; identified no mineral resources or evidence of mining activity in the Sheep Divide RARE II area. A deposit 10 mi (16 km) southwest of the area contains copper and silver minerals in the Triassic Wild Sheep Creek Formation which probably underlies basalt lava flows covering the study area. Abundant basalt in the area can be crushed and used as aggregate, but suitable deposits closer to markets are widely available No sand, gravel, coal, oil, gas, or geothermal resource, were Identified. INTRODUCTION Location and Access The Sheep Divide RARE II area [10 mi (16 km) west of the Snake River] encompasses 7,100 acres (2,800 ha) of the Hells Canyon National Recreation Area in the Wallowa-Whitman National Forest. Enterprise, Oregon, is located 23 air mi (37 (m) west of the area. Peripheral access is provided by the highway from Joseph to the community of Imnaha, Oregon, then south to the study area by the graveled Upper Imnaha Road (fig. 1).

Jan 1, 1983

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure'' or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", “canopies” , "roll bars" , protective structures" and other such descriptive names. In this report, "ROPS" describes the function of the structure; "FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection. “MESA” is used as an abbreviation for the Mining Enforcement and Safety Administration; "USBM" is used to abbreviate the U, S. Bureau of Mines.

By M. M. Tilman

The Bureau of Mines investigated the precipitation strengthening of lead¬-base alloys containing 0.5 through 4 weight-percent combined Cd plus Sb. The Cd and Sb were alloyed in a 1-to-1 atomic ratio which maintained compositions along the quasi-binary section Pb-CdSb. Tensile properties, creep rates, and stress-rupture values were obtained on alloys in the aged condition. The highest tensile strength was observed in an alloy of Pb-3 CdSb, After aging for 6 months at 90°±3° F, this alloy had a mean tensile strength of 8,950 psi with 15-percent elongation. An aged alloy of Pb-1 CdSb exhibited a steady state creep rate of 1.2 X 10-3 percent per day at a stress of 500 psi and a temperature of 90°±3° F. Times to rupture at stresses up to 4,000 psi and at a temperature of 90°±3° F were obtained for some compositions.

Jan 1, 1970

By R. A. Friedel

Data on compositions of natural substances are important in the study of possible interrelationships. The similarity of the low molecular weight alkane isomers from crude oil and Fischer-Tropsch catalytic synthesis product has been reported (8).3 A similar composition for the alkane isomers from high-temperature coal carbonization has been found. The composition of the C4 to C 7 alkane isomers from these three sources can be calculated quantitatively with the equations previously developed to calculate alkane isomers in Fischer-Tropsch product. An KM sting reversal of the concentrations of the monomethyl isomers from C6(2 Me > 3 Me) to C7 (3 Me > 2 Me) occurs in all three products; fragmentary comparisons at higher carbon numbers indicate some dissimilarities. Naphthene isomers in the C6 to C7 range for crude oil and high-temperature coal carbonization also have similar compositions. Aliphatic hydrocarbons from low-temperature coal carbonization processes are considerably different, consisting mainly of normal alkanes.

Jan 1, 1968

By T. F. Tomb

This paper describes field and laboratory investigations conducted on a dust-collection system recently designed for integral use with a continuous mining machine. The results of the field study showed that the average respirable dust concentration measured at the machine operator's position was reduced by about 60 percent (from 8.7 to 3.5 milligrams per cubic meter), and total and respirable dust concentrations in the return air were reduced by approximately 70 percent. The data indicated that approximately 20 percent of the dust generated at the face was not passed through the scrubber. The lab-oratory results showed that the overall efficiency (by particle count) was approximately 80 percent for total dust concentrations (minus 20 micrometers in size) typical of those encountered underground. Calculations based on total dust concentrations measured during the underground study indicated that the respirable mass concentrations of the effluent from the scrubber would still exceed acceptable levels even if scrubbing of all the air at the face were possible.

Jan 1, 1973

By F. W. Lane

[The rapid expansion of the petroleum industry, the steadily growing use of oil fuel or steamships, the increasing transportation of oil in tankers and the extensive use of petroleum oils for many land industries, has resulted in pollution of our coastal eaters by these oils. On account of the great importance of this problem to the petroleum and shipping industries its, the Bureau of Mines, in cooperation with the American Petroleum Institute and -he American Steamship Owners Association has undertaken to ascertain the extend of petroleum oil pollution along the coasts of the United States and to indicated the principal so arcs of such pollution. Certain typical methods and devices in use and proposed for the separation of oil from water, and for the disposal of oily castes from ships and industrial plants have been studied. An attempt has also been made to point out the nature of the fire hazard resulting from oil pollution and to indicate the effect of such pollution on bathing beaches.]

Jan 1, 1924

By L. D. Tracy

The first study of this subject hits been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal-mining industry to standardize the forms of leases, and so avoid some of the abstruse and ambiguous clauses which slay be found in many of them and the consequent liability of costly litigation. In some of the publications of the Illinois Mining; Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the 'State have been divided into eight geological districts, each district being treated separately. This report covers District No. VI of that classification, and it is hopped that studies of the other districts will be completed in the near future and similar results published.

Jan 1, 1926

By F. S. Karn

Measurements were made of the flow of helium, methane, ethane, butane, and toluene through thin disks of coal. All measurements were made on a dense layer in the Pittsburgh seam identified as attritus. Flow increased with pressure differential and temperature. At room temperature and a pressure differential of 1 atmosphere flow rates along the bedding plane of Pittsburgh seam coal were helium 881 X 10-10 cm2 sec-1, methane 1.2 X 10 -10 cm2 sec-1, ethane 0.54 X 10-10 cm 2 sec-1, n-butane 0.35 X 10-10 cm2sec-1, and toluene 3.8 X 10-10 cm2sec-1. Flow rates were 50 percent lower across the bedding plane of the coal than along the bedding plane. Activation energies were 3.9 kcal mole-1 for helium and 13.6 kcal mole-1 for methane, with diffusion measured either along or across the bedding plane.

Jan 1, 1970

By R. P. Beyer

Low-temperature heat capacities and standard enthalpy of formation of copper difluoride (CuF2) were determined by the Bureau of Mines. The low-temperature heat capacities were determined from 11 to 302 K by adiabatic calorimetry. The enthalpy of formation was determined by HC1 solution calorimetry. The standard values of entropy (S°) and enthalpy of formation (?Hf°) at 298.15 K are l8.65±0.03 cal/deg mole and -129.02±0.29 kcal/mole, respectively.

Jan 1, 1978

By John Durkin

Information on vertical magnetic noise in the voice frequency band, both within and above coal mines, is needed for the evaluation of through-the-earth baseband electromagnetic communications at mines where horizontal loop antennas are used. This report discusses the theory of the source of electromagnetic noise, the propagation of this noise to an observation point above a mine, and its interaction with the local earth conductivity structure, which gives rise to vertical magnetic noise. The relationship of surface noise to underground noise is also discussed. Bureau of Mines investigators made surface and underground vertical magnetic noise measurements at a number of coal mines located through- out the United States. These data were modeled through regression analysis to characterize expected noise levels. The results are presented, including results in one-third octaves for use in evaluating the expected performance of through-the-earth communication systems by articulation-index studies.

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Abstract—Overhead electric power lines present a serious electrocution hazard to personnel in a variety of industries. Overhead lines, typically uninsulated conductors supported on towers or poles, are the most common means of electric power transmission and distribution, and are exposed to contact by mobile equipment such as cranes and trucks. Equipment contacting energized overhead lines becomes elevated to a high voltage, and simultaneous contact by personnel of the “hot” frame and ground can cause serious electrical shock and burns. Industries where risk of these accidents is greatest include construction, mining, agriculture, and communications/public utilities. An estimated 2300 accidental overhead line contacts occur each year in the U.S. This paper describes a practical low-cost concept to detect actual contact of mobile equipment with a high-voltage line and provide a warning. Accident statistics indicate that more than half of the fatalities could be prevented by such a device. Index Terms—Crane, electrical shock prevention, engineering control, mining, mobile equipment, power line.

By G. M. Wilemon

The Bureau of Mines conducted preliminary investigations on the use of an acid-alcohol leaching technique for recovering phosphate values from phosphate matrices. H2S04 and methanol were used as the leaching agents. Starting-matrix particle size and acid-apatite ratio were found to significantly affect the efficiency of phosphate leaching. Phosphate extractions of more than 80 pct were obtained when minus 200-mesh ore was used and the acid-apatite ratio was 8:1 or more. The iron and aluminum oxide impurities (R203) present in the crude acid products were monitored, and R203-P205 ratios are reported. Phosphate extractions in excess of 80 pct also were obtained when phosphatic clay wastes were leached. Typically, leach slurries filtered using test leaf filters ex-hibited filtration rates of 100 lb/(h·ft2) or more.

Jan 1, 1987

By A. J. Barry

A method was developed for testing the anchorages obtained with 3/4-inch, expansion-type, headed bolt and shell assemblies. The apparatus is a modification of that used in testing -inch-diameter, slotted-type bolts. Four makes of expansion-type shells were used in 64 tests made in sandstone and shale roof. The results show that for 3 makes of shells the anchorage effectiveness is independent of the installed land, and for the fourth make of shell a better anchorage is obtained when instilled at a load of 8,000 pounds. The results also show that deformation of the expansion plug influences the majority of the anchorages obtained with two makes of shells. This deformation causes a larger increase in displacement for a given added increment of load. The data from 48 of the 64 tests were combined to establish a relationship between average displacement and increase in bolt load (above the installed load). This relationship can be used to evaluate the anchorage effectiveness of any 3/4-inch-diameter, expansion-type, headed bolt and shell assembly tested in the field.

Jan 1, 1956

By Robert L. Chufo

This paper describes a general purpose imaging technology developed by the U.S. Bureau of Mines (USBM) that, when fully implemented, will solve the general problem of "seeing into the earth." A first generation radar coal thickness sensor, the RCTS-1, has been developed and field-tested in both underground and highwall mines. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data that enables signal processing to solve the problems of media, target and antenna dispersion. Knowledge of the dielectric constant of the media is not necessary because the electrical properties of the media are determined automatically along with the distance to the target and thickness of each layer of the target. The sensor was developed as a navigation guidance sensor to accurately detect the coal/noncoal interface required for the USBM computer-assisted mining machine program. Other mining applications include the location of rock fractures, water-filled voids, and abandoned gas wells. These hazards can be detected in advance of the mining operation. This initiating technology is being expanded into a full threedimensional (3-D) imaging system that will have applications in both the underground and surface environment.

By R. K. Koch

In seeking substitutes for such critical metals as chromium, cobalt, and nickel, the Bureau of Mines investigated techniques for shape-casting titanium in rammed sand molds. Castings were made in olivine, garnet, chromite, and, for comparison, zircon. It was found that commercial-grade castings up to 31 lb (maximum capacity of furnace) could be made in zircon or olivine molds if a zirconia mold wash was used. Castings up to 4 lb could be made in chromite molds, but heavier castings suffered from some mold-metal reaction. Garnet molds were found to be unsatisfactory for castings of all sizes because of gas blows and rough surfaces. In other tests shell castings of acceptable quality were produced in water-glass-bonded zircon and olivine molds up to weights of 8 lb, but chromite molds were unsatisfactory because rough casting surfaces were caused by mold-metal reaction. Unlike the currently used commercial processes, neither the rammed-sand nor the shell-molding processes developed by the Bureau of Mines generate noxious fumes at any step.

Jan 1, 1980

By J. H. Russell

As part of its efforts to maximize resource recovery, the Bureau of Mines conducted studies to recover valuable byproducts from Western phosphate beneficiation tailings. Potential byproducts include phosphorus, vanadium, and uranium. The objective was to determine roasting and leaching conditions for maximum dissolution of vanadium from tailings containing approximately 13 pct P205 and 0.23 pct V. Sulfuric acid leaching tests were conducted with the tailings either as a dilute suspension dried, or in a roasted condition with or without NaCl added during roasting. More than 90 pct of the vanadium was dissolved by roasting at 850° C for 120 min with 8-pct NaCl and leaching at 75°C for 120 min with an excess of 2N H2S04, By roasting without NaCl and avoiding the difficulties of the chloride impurity, nearly 80-pct vanadium dissolution was achieved with an 800° C roast for 180 min. Quadratic regression equations were derived to relate vanadium dissolution to roasting and leaching conditions.

Jan 1, 1982

By Oliver Bowles

Wire saws have been used for many years in European travertine, marble, and slate quarries. This method of sawing found very limited use in America until 1927 when it was accepted as standard equipment in elate quarries in Pennsylvania where it has been remarkably successful. Details of its operation in slate have been published in a recent bureau report.3 The very limited extent to which the wire saw has been employed in limestone and marble quarries in the United States and the seeming lack of interest even in experimental work to determine its advantages are difficult to explain in vied of its wide use in cutting similar rocks in Europe and its unquestionable advantages in sewing slate in America. In order to encourage improvement in quarry practice the United States Bureau of Mines has endeavored to obtain information as to the extent to which wire saws are used in Europe together with data on the rate and cost of sawing. The information at hand is by no means complete either in territory covered or in details of operation; it nevertheless brings out certain significant features that may be of interest and advantage to quarrymen in the United States.

Jan 1, 1931

Improve the reliability and accuracy of subsurface images using constrained tomography with enhanced ray-tracing capabilities. Background Geophysical tomography is a technique for imaging the structure of a rock mass using seismic or radio waves, in the same way that medical CAT scans image human tissue using X-rays. Tomography has found numerous practical applications related to mining, including lithologic and structural characterization, fracture detection and fluid monitoring, void detection, and evaluation of stress state and integrity of mine structures. Problems Two fundamental problems have largely prevented geophysical tomography from enjoying the tremendous success achieved by medical tomography. The first is a consequence of practical limitations on the placement of sources and receivers of wave energy: ideal resolution can be attained only when the region being imaged is entirely surrounded by sources and receivers, so that it is crossed by rays traveling in all possible directions. When such coverage is impossible or impractical, the inversion becomes underdetermined: there id not enough information in the measured data to provide a mathematically unique solution. The second major problem in geophysical tomography is the necessity for detailed ray tracing. Commercial software, as well as previous U.S. Bureau of Mines (USBM) software, employs a ray-shooting algorithm that may be unable to model some ray paths when velocity contrasts are larger than about 100%. These ?shadow zones" result in loss of data and degradation of reconstructed images.

Jan 1, 1994