Search Documents

By F. J. Bailey

"In the fall of 1919, the U.S. Bureau of Mines began an inquiry as to the possibility of utilizing airplanes in conjunction with its rescue work, for quickly transporting engineers and oxygen rescue-apparatus to mine disasters.It was realised that this proposed use of airplanes has serious limitations, and if it were feasible, that the Bureau would have to rely on the cooperation of the established aviation fields of the U. S. Air Service for furnishing airplane service. Therefore Van. H. Manning, Director of the Bureau of Mines, under date of October 28, 1919, wrote the Director of Air Service outlining the rescue and first aid organization of the Bureau, the location of headquarters of district engineers, the distribution of safety cars and stations, and other essential details, and asking whether the Air Service could cooperate with the Bureau in the event of serious mine disasters. Major-General Charles T. Menoher, Director of Air Service, responded that the Air Service would be glad to cooperate insofar as possible, and designated those Air Service stations nearest the district engineers' headquarters, which might be best able to assist.The Bureau of Mines has ten mine rescue cars and eight mine safety stations distributed throughout the mining regions of the United States. The cars are each equipped with sets of oxygen mine-rescue breathing-apparatus and first-aid supplies. The car personnel consists of a mining engineer, surgeon, foreman, first-aid miner, clerk and cook. A foreman miner is in charge of each station and at five of the eight stations are mine safety trucks. The work of the cars and stations is two-fold; (1) Assisting in rescue and recovery work at mine disasters, and (2) training miners in mine rescue and first-aid methods, and in investigations looking to prevention of mine accidents. The country is divided into nine safety districts, with nine district engineers in charge."

Apr 1, 1920

By L. C. IlsLey, E. J. Gleim

It is the firm belief of the Bureau's engineers that the introduction of electrical mining machines has done much to increase safety in mining as a whole . There can be no doubt but that the substitution of machine mining together with permissible powder for the method of " shooting from the solid " has been the means of saving the lives of many shot- firers . Machine mining also leaves the roof in a better condition as lighter charges of powder are required to bring down the coal . Thus the danger from falls of roof are lessened . It is recognized that every effort should be made to prevent all accidents due to the use of electrical machinery but it is felt that any action tending to limit the use of such machinery would be a backward rather than a forward step in the safety measures laid out to decrease the hazards in coal mining .

May 1, 1920

By J. A. Organiscak

The U.S. Bureau of Mines recently conducted an investigation into the amount of respirable and quartz dust generated while mining rock in coal mines by continuous and conventional methods. The study was made at two mines that use both continuous and conventional mining. Results show that continuous mining produces 1.2 to 3 times more respirable dust, and 6.7 to nearly 15 times more quartz dust than conventional mining.

Jan 1, 1989

Provide the mining industry with an easy-to-use means of accurately predicting surface subsidence caused by longwall mining in the northern Appalachian Coal Basin. Approach The Bureau of Mines developed a subsidence prediction model using the novel approach of a variable subsidence coefficient. This approach had to be used because of the resistant strata types which commonly occur within the relatively thin overburden material typical in northern Appalachia. Such resistant strata precluded the use of the popular European methods that assume homogeneous overburden or overburden behaving as homogeneous from a subsidence point of view. The model is available in a BASIC computer program for use on most personal computers. The user has the options of obtaining individual subsidence calculations or may choose to develop a subsidence profile using an average overburden value. The program output can be generated in graphic or tabular form showing the location of the surface point with respect to the longwall panel edge, overburden depth, and the subsidence value.

Jan 1, 1986

By George S. Rice, L. C. IlsLey

"A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details:""The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all appearances, passed down the shaft caus¬ing disruptive discharges at certain points between the guides and the winding rope, rending the latter at two places situated respectively .228 .feet and 278 feet from the surface, The distance between the winding rope and the side of the shaft was 5 feet 4 inches, indicating a spark gap ;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft.""The Compressed Air Magazine, January 1920 issue, which contained the above extract also goes on to state;""In 1915, M, Ferey described in a paper read before the Societe de l'Industrie Minerale phenomena of a similar character to the above. In a pit liable to sudden outbursts of gas, for the sake of safety, shot firing was carried out from the surface. During a storm, in the year 1905, shots went off in two places after the detonators had been connected to the conductors) we read in the Colliery Guardian, London. These shots were situated respectively 1,400 and 1,410 metres from the firing station, Realizing the possible danger from this cause, the precaution was taken to cut the conductors at the bottom of the shaft and to connect there just before firing, Even under these conditions a shot went off spontaneously, -.owing, it is believed, to lightning."""

Feb 1, 1920

By Robert L. Chufo

The U.S. Department of Energy Pittsburgh Research Center,1 has developed and field tested a spatial, spectral sensor for measuring the thickness of mineral deposits. Knowledge of the dielectric constant of the material is not necessary because the electrical properties of the media are determined automatically along with the thickness or distance measurement. The technology was developed to measure the thickness of coal remaining in the roof and floor of a mine or the thickness of a coal pillar remaining between two mining entries for the purpose of guiding a mining machine. However, field tests have shown the new technique is equally valuable for measuring the thickness of each layer in a multilayer manmade structure such as highway paving or building foundations and the thickness of geological deposits other than coal, such as, salt, granite and sandstone. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple dipole sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data and enables frequency domain signal processing to solve the problem of media, target and antenna dispersion. The technique overcomes the problem of multipath reflections from nearby metal structures and avoids the use of radio frequency absorbing material. In its present form the system measures material thickness of zero to over 3 m to within ±2.5 cm accuracy. The system parameters are variable to suit the application but for most applications default values of 40 cm antenna motion with measurements made at 401 frequencies from 0.6 to 1.4 GHz at each of 32 antenna positions with a power level of 0 dBm or less are more than adequate to provide a satisfactory signal-to noise ratio. In the range of 0 to 10 m the system operates in the continuous wave mode and by simply turning off the transmitter for ranges beyond 10 m the problems of time domain processing are entirely avoided. The technique can be implemented with a vector network analyzer, a servo controlled L-band antenna positioner, an IEEE488 bus controller and a process computer. An electronics package designed and constructed to operate in the harsh mining environment and providing 1, 2 or 3 dimensional image presentation is being evaluated as a replacement for the network analyzer. Key words: Ground penetration radar, Spatial, Spectral

By David C. McHuron

The U. S. Bureau of Mines in their continuing research into sealants, selected MBAssociates to design, build, and test equipment and evaluate sealant as to its effectiveness is shale degradation. There were 20,050 sq.ft. of coal mine roof sprayed with a mine sealant and as a result, it has been estimated that the sealant coated roof has from 50% to 95% less roof falls than that roof which was not coated with sealant.

Jan 1, 1980

By G. S. Morrow, C. D. Litton

This report presents the results of a U.S. Bureau of Mines evaluation of smoke detectors placed in conveyor belt entries of underground coal mines. The selected mines are located in six different Mine Safety and Health Administration (MSHA) districts, are operated by seven different companies, and use atmospheric monitoring systems from seven different manufacturers. Principal concerns are early detection and warning of fires, reliability of operation, frequency of maintenance, and adaptability of detectors to monitoring systems and the mining environment. The data contained in this report provide for some comparisons between smoke detectors and CO sensors, specifically in the areas of early detection of fires and susceptibility to nuisance alarms due to diesel exhaust contaminants. Finally, recommendations for performance standards, sensitivity tests, detector classification, and maintenance are presented.

Jan 1, 1992

Allow miners to communicate via the pagerphone system when they are not near one of the phones. Approach A small lightweight pagerphone, having crocodile clips which pierce the phone line insulation, was developed. How It Works The Portable Telephone/Intercom is temporarily clipped onto an existing pagerphone line at any location, and operated like an intercom. It is riot necessary to strip the insulation from the pagerphone line to make the connection. In addition to the clips for connecting to pagerphone line, the Portable Telephone/Intercom consists of a small belt-carried control box, an ear-phone, and a bone-conduction microphone which is attached to the webbing in a miner's helmet. All together, these components weigh only 20 ounces including the batteries

Jan 1, 1977

Reduce costs of surface mine reclamation by improving scaper operating efficiency and reducing tire costs. Approach The Wheel Slip Monitor senses and compares the peripheral speed of a scraper's four tires 10 the true ground speed of the scraper, and alerts the operator if any of the tires exceeds a predetermined amount of slip. This system helps scraper operators reduce wheel slip during the loading cycle, thereby improving the loading efficiency of the scaper and reducing tire wear and damage. How It Works The system consists of five ultrasonic doppler velocity-sensing devices for measuring the speed of each wheel as well as the true ground velocity (see photograph). Each sensor produces an electrical output signal having a frequency proportional to the speed of the tire or terrain. The signals are conveyed through electrical cables to a control box in the operator's cab where they are converted to voltages proportional to individual wheel speeds (see photograph). The signals are further processed to activate a blinking red light, corresponding to any individual wheel which is slipping, and to sound a beeping tone that is audible to the scraper operator. The rate at which the light blinks and the tone beeps is proportional to the degree of slip. Alerted, the operator can take corrective action.

Jan 1, 1985

By B. Dimitriades

Exploration of the photochemical reactivity of diesel-exhaust hydro-carbons is described. A smog chamber was built, and reactivities of diesel exhaust, gasoline exhaust, and propylene were measured at two chamber temperatures. Experimental data indicated the problems caused by instability of diesel-exhaust hydrocarbons. With reservations due to these problems, the results are interpreted to reflect comparable reactivities for diesel and gasoline exhaust.

Jan 1, 1971

By Steven J. Page, John A. Organiscak, Thomas Mal

Monitoring the miner respirable quartz dust exposure for compliance with U.S. federal regulations is mandatory to protect the health of coal miners. However, there is no technique available for the direct measurement of the respirable quartz dust concentration in the mining environment. The only means to estimate the respirable quartz dust concentration is to perform an analysis of the respirable dust sample collected, which contains both coal and quartz dust as well as other mineral constituents. For samples collected at coal mines, the U.S. Mine Safety and Health Administration (MSHA) utilizes the P7 method for respirable quartz analysis. The objectives of this work are to 1) evaluate the performance of the P7 method on field samples of low quartz mass loadings, 2) evaluate the magnitude of dust mass spatial variability within an enclosed cab environment, and 3) estimate the subsequent propagation of error in calculating the per. centage of quartz over a broad range of mass and quartz filter loadings at a surface coal mine. These objectives were achieved by obtaining surface coal mine dust samples over a 9-month time period in enclosed cabs of three drills and three bulldozers. By measuring weighing precision and using reasonable estimates for sampler variability, the dust mass spatial variability component was calculated by difference. The results show that 1) the P7 method can be precise and linear with quartz mass loadings as low as approximately 5 µmg of quartz, 2) the dust mass spatial variability, even within an enclosed cab environment, is the dominant factor of variability in propagation of error in estimating the quartz content of the obtained dust samples on a percentage basis, and 3) weighing precision is not a significant factor in error propagation. In addition to the enclosed cab samples, samples from eight surface coal mine drills were collected at various locations exterior to the drill cab. Significant data scatter at these outside locations strongly suggests that the ambient dust mass spatial variability has a significant effect on the propagation of error in estimating quartz content of the dust samples on a percentage basis.

By M. E. Tyrrell

Work in this investigation was undertaken by the Bureau of Mines to demonstrate how waste glass might be utilized to lower the required firing temperature and firing time of structural clay products. Mixtures of waste glass and common clays were formed by stiff-mud extrusion and fired to the temperature required to produce a body having 6 to 7 percent absorption. Substitution of glass for one-half of the clay in a red body reduced the firing temperature 500° F, which made possible a 30-percent increase in production; in a tan body, the firing temperature was reduced 400° F, which made possible a 23-percent increase in production.

Jan 1, 1972

By Lawrence Y. Marks

During the mineral survey of the Bob Marshall Wilderness and study areas by the author in 1971, 1973, 1974, and 1976 (Marks, 1978), the area designated Reservoir-North (RARE II No. H1-485) in January, 1979, (U.S. Forest Service, 1979) was examined, along with other lands adjacent to the earlier study areas. However, the 1978 open-file report covered only areas originally designated for study. The present report on Reservoir-North is based on earlier work. No work has been done in the area since 1976. Mineral Appraisal Reservoir-North RARE II area (No. H1-485) is in the Northern Disturbed Belt which has been identified as having high potential for natural gas accumulations and lesser potential for oil accumulations (Mudge, 1978). Oil and gas lease applications in the area, indicate interest by oil companies.

Jan 1, 1981

By Allen D. Look, Alan A. Sharp

"Churn drills for blast-hole drilling are important to the operation of most open-pit metal mines, but certain hazards are created through their use that cause fatal and nonfatal accidents.2/ The purpose of this circular is to present a code of safe practice prepared and followed at a large Arizona open-pit copper mine, where safety is recognized as a definite operating problem. Such a code, based upon a thorough study of available published information as well as practical experience gained from accidents and near accidents, is the result of considerable effort and monetary expenditure. It is hoped that other operations using churn drills may benefit by the code presented, either in comparison with existing rules or in the preparation of new operating instructions.The code presented is in use at the Morenci Branch of the Phelps Dodge Corn., Morenci, Ariz. Similar codes are used at the New Cornelia Branch, Ajo, Ariz., and in the waste-pit operation at the United Verde Branch, Jerome, Ariz.The authors gratefully acknowledge the cooperation of the Phelps Dodge Corp., whose personnel made: possible the collection of information included in this circular. Special acknowledgment is due Paul Simmons, safety engineer, and 3. U. Larsen, general drilling and blasting foreman, Morenci Branch, Morenci, Ariz.The importance of churn drills in Arizona mining is apparent when it is realized that at all the open-pit copper mines blast holes are drilled with this equipment. At Morenci, approximately 98 percent of the ground is broken by primary blasting of churn-drill holes.There has been a growing tendency in Arizona's copper-mining industry to change from underground to open-pit mining, with consequent increase in the use of churn-drill blast holes for primary blasting.3/Thirty-three churn drills are in use at Morenci for blast-hole drilling. The drills operate with 440-volt alternating current, and trailing drill cables, in 500-foot sections, connect with the portable drill transformer station.4/ Three Diesel-driven churn drills for drilling prospect holes also are in use. About 25 churn-drill shifts are operated currently on a three-shift basis. Ordinarily, a two-man crew is assigned to each drill; however, with prospect-drill crews a third man is added to handle the sampling.Benches are carried at a uniform height of 50 feet. Churn-drill holes are 9 or 12 inches in diameter and about 60 feet deep. The holes are 18 feet apart in hard waste and 21 feet in soft waste and ore, with toes from 11 to 13 yards at the shovel grade. Both the hole spacing and the toe have been increased gradually, until they are now 2 yards longer than in 1940. The average ground broken per hole is 3,500 tons, or 60 tons of ore per foot of hole drilled. The holes are drilled 10 feet below the bench to avoid leaving hard bottom, which requires secondary drilling and blasting.Starting with a 12-inch casing, the prospect holes average 1,200 to 1,500 feet in depth and terminate with 6-inch casing; the deepest hole drilled to date went to 1,735 feet.In addition, churn-drills are used at Morenci to drill blast holes in the silica pit, limestone quarry, and the tailings dam. Other irregular applications are the drilling of holes to set trolley roles and for concrete piling in building foundations."

Jan 1, 1950

By Charles L. Kimbell

This study is intended to serve three roles. First, it is the second annual edition of this study in a separate volume that represents a global overview and summary to supplement and complement the five regional volumes that now constitute the U.S. Bureau of Mines international, geographically arranged studies. In this regard, it also extends previous works under this title that appeared in the inter-national volume of the Minerals Year-book from the inception of that volume (the 1963 edition) until it was subdivided into six separate volumes in 1989. Following the traditional format of past chapters under this title, the basic statistical presentations herein deal chiefly with 1990, and in a few instances with 1988 or 1989; these latter two only because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting on the world's mineral industry that have occurred between the end of 1990 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By Wilbert J. Huff

For the past 8 years the technical studies conducted by. the Explo- sives Division of this Bureau have been summarized in a series of annual reports.3 This report deals with activities from July 1, 1942, to June 30; 1943. Specific problems have been in immediate charge of section or unit leaders, to whom credit is given.

Feb 1, 1944

By Michael J. Griffin

Science involves the study of the nature and behaviour of natural things and the knowledge we obtain about them. Scientific endeavour leads to the unfolding of new knowledge and adjustments to our understanding and our behavior. To indicate that we ‘know’ something may merely mean we do not feel able to, or that we do not wish to, disagree with others who claim to know; or it may mean we have either heard about it, or studied it, or understand part of it, or accept that it is true, or have seen evidence to be convinced of its veracity. What do we ‘know’ about the health effects of vibration? There are many unknowns in the field of human responses to vibration. Not all would agree on what is known and what is unknown. This paper seeks to summarize what we know that we know, what it is sometimes claimed that we know, and what we know that we do not know about the relation between exposures to vibration and our health. It also speculates on what we do not know that we do not know. Hand-transmitted vibration What we know we know We know that exposures to hand-transmitted vibration result in various disorders of the hand, including abnormal vascular and neurological function. Not all frequencies, or magnitudes, or durations, of hand-transmitted vibration cause the same effects. What we may claim to know To enable exposures to be reported and compared, they are ‘measured’ and ‘evaluated’ using defined (e.g. standardised) procedures. This involves identifying what is to be measured and specifying how it is expressed by one (or a few) numbers. Summarising a vibration exposure in a single value involves assuming the relative importance of components within the vibration (e.g. different magnitudes, frequencies, directions, and durations), so standards define ‘weightings’ for these variables. The importance of the weighted values may also be suggested, allowing ‘assessments’ according to a criterion (e.g. the probability of a specific severity of a specific disease). Standards for the measurement and evaluation of hand-transmitted vibration define a frequency weighting and time dependencies that allow the severity of vibration exposures to be assessed and the probability of finger blanching to be predicted 1. What we do not know We do not know that the frequency weighting in current standards reflects the relative importance of different frequencies and axes of vibration in producing any specific disorder. We do not know whether the energy-based daily time-dependency inherent in A(8) reflects the relative importance of vibration magnitude and daily exposure duration. Consequently, the relation between A(8) and the years of exposure to develop finger blanching, as in an appendix to ISO 5349-1 (2001), is not well-founded. We do not know, or at least there is no consensus on, the full extent of the disorders caused by hand-transmitted vibration (e.g. vascular, neurological, muscular, articular, central), or the pathogenesis of any specific disorder caused by hand-transmitted vibration, or the roles of other factors (e.g. ergonomic factors, environmental factors, or individual factors). We know that acute

Jan 6, 2006

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957