Search Documents

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By Harold C. Pierce

"INTRODUCTION During the years 1941 to 1945, the United States produced less than one-half of one percent of all primary nickel, whereas the nation's consumption of the metal amounted to nearly three-fourths of the world's supply. Although postwar nickel consumption probably will be less than wartime consumption, trade- estimates for the next 10 years are well above the average established during the 1930-1940 decade. The greatest consumption is expected in nickel alloys, particularly nickel-alloy steels. 3/ The greater use of nickel cast irons and nickel-clad metals also signifies an expanding nickel market. In anticipation of the postwar demand for nickel, and realizing the seriousness of the ""have not"" position of the United States with respect to this metal, the Bureau of Mines, sent an engineer 4/ into the lower Copper River region of Alaska during the summer of 1944 to investigate the nickel deposits near the head of Canyon Creek. Samples from the Spirit Mountain nickel prospect were sufficiently encouraging to justify more intensive exploration. As a result, a program of surface trenching, systematic sampling, and detailed mapping of the property was adopted and directed by a Bureau of Mines engineer 5/ in the summer of 1945."

Aug 1, 1946

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By S. Gallagher

If we consider ergonomics to be an exercise in matching job demands to worker capabilities, one of the principal capabilities we must be concerned with is that of human strength. Our ability to evaluate different characteristics of muscular strength has increased dramatically over the past couple of decades with the development of new and increasingly sophisticated instrumentation. One would think that armed with such advanced techniques, we might be able to develop methods to conclusively identify workers at risk of injury in physically demanding jobs. Unfortunately, this has not yet proven to be the case. Instead, what these instruments have continued to point out is how intricate a function muscular strength really is, and how complicated and ambiguous its relationship is to musculoskeletal injury. While we cannot just use isolated tests of strength to specify precisely who may be at risk of injury, studies have indicated that strength testing can be a useful tool for job design and, under certain circumstances, selection of workers for demanding jobs. However, because strength is such a complex phenomenon, there has often been some confusion regarding the proper application and interpretation of strength tests in ergonomics, especially among persons not thoroughly familiar with the limitations and caveats associated with the available procedures. The purpose of this chapter is to discuss some of the fundamental principles of strength assessment in ergonomics, so that these procedures can be better applied to control the risk of musculoskeletal disorders in the workplace 1.1. What is Strength? (And what are we Measuring?) Many of the complications associated with strength assessment arise from the simple fact that even our most sophisticated machinery does not directly measure the force or tension developed by a muscle in a living person. Instead, we can only observe the consequences of force development by a contracting muscle, or more likely, by a combination of muscles There are many ways in which we can measure the effects of muscular contraction, and the techniques we use can have a dramatic impact on the strength readings we will obtain. Consider the situation illustrated in Figure 1. In this example, the muscle exerts a constant force of 1000 Newtons (N). However, the forces we measure can vary quite dramatically depending on where we place the force cuff - from 167 N if we place it near the wrist to 500 N if we place it near the elbow. Which value should we select as properly representing the muscular strength for this elbow flexion exertion? The preceding example illustrates some important points with regard to strength assessment. Perhaps the most important is that "muscular strength is what is measured by an instrument" (Kroemer et al. 1999). It should also be clear from this example [ ] that two researchers could perform an elbow flexion strength experiqent on the same group of subjects, but if each selected different force cuff positions, they might end up with wildly differing estimates of strength. Differences in the strengths of various muscle groups in the published literature may be the results of differences in the procedures and measurement methods used by the experimenters Thus, it is critical that any strength data presented be accompanied by a detailed account of the manner in which the data were obtained. A few additional points need to be made with regard to the testing of human strength. We must be clear that what we are obtaining in such tests are not a person's maximal strength capability, but their maximal voluntary strength. The voluntary nature of the exertion introduces an unknown, but surely substantial, amount of variability in our measurements of strength. One can imagine two subjects with identical muscular strength capabilities, but with varying levels of motivation or discomfort tolerance, for example. We are likely to observe considerable differences in the voluntary force exerted by the two, but it should be understood that such results may be largely the result of psychological factors, and not differences m muscular strength per se. The important point to be made here is that not only are we unable to directly measure muscular force, what we are able to measure is modified by an invisible filter - a filter subject to a wide variety of influences and which will differ considerably for every person we test To make matters worse, this filter would be expected to change even within a given individual on a given day. From the foregoing discussion, one can perhaps better appreciate some of the difficulties with establishing a definitive relationship between an individual's measured strength and that individual's risk of injury.

By Thomas J. Peters

The U.S. Bureau of Mines studied the 63,9SS-acre Hanson Lakes study area, including the Ten Mile-East and part of the Ten-Mile West RARE II areas, plus additional acreage, all proposed at times for Wilderness designation. The study was part of a Idaho Land Assessment Program with the Idaho Geological Survey and the U.S. Geological Survey, to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The area is at the north end of the rugged Sawtooth Range and includes parts of the Sawtooth National Recreation Area which is closed to mineral location. The Copper Mountain. Elk Mountain, and Observation Peak mineralized areas are in the study area, but only Copper Mountain is open to claim location. It is on the trans-Challis fault zone and contains Tertiary granite which is favorable for mineral deposits of gold, beryllium, niobium, REE (rare-earth elements), tin, molybdenum, copper, silver, and lead. Identified resources are 1.9 million tons of flake graphite at Elk Mountain, but much more graphite occurs in the vicinity REE occurs in 18 black sand placer sites along the lower reaches of study area streams just outside the study area, on Cape Horn Creek, Marsh Creek, and lower Valley Creek flood plains, and at one hydrothermal site near Observation Peak. Hydrothermal REE is commonly low in? by-product thorium. a radioactive disposal problem. Many advanced REE applications enhance the quality of life, and future uses in superconductivity may reduce energy consumption. Seventeen lode, one geothermal, and 11 placer prospects were examined. Workings totaled about 20 adits, one shaft, several open cuts, and numerous small pits. Approximately 500 mining claims have been located or relocated in the study area, including a 200-claim block for disseminated molybdenum.

Jan 1, 1992

By Samuel W. McNary

In August 1984 the U.S. Bureau of Mines conducted a study of the mineral resource development potential of the Badger Canyon-Antelope Creek area, within the Boulder-Pioneer wilderness study area, about 5 miles northeast of Ketchum, 10. The purpose of this study was to investigate in greater detail an area which was designated by the U.S. Geological Survey (USGS) and the Bureau as having a moderate mineral resource potential for zinc, molybdenum, lead, and silver, and a low potential for copper. One hundred twenty-eight soil samples were taken along a 6,2S0-ft traverse on the ridge separating Badger Canyon and Antelope Creek. 5 Five rock samples were collected from old prospect pits and mineralized outcrops. All samples were analyzed for gold. Silver, copper, lead, zinc, molybdenum, arsenic, antimony, vanadium, and mercury. The metal concentrations in the soil samples along the traverse are irregularly distributed. Samples collected near old prospect pits tend to be high in lead and zinc, undoubtedly a reflection of underlying galena-and sphalerite-bearing quartz veins. All of the copper and mercury values in the soils are less than the detection limit, as are most of the lead, molybdenum, and antimony values. Except for lead and zinc values, the metal concentrations in the rock samples are low. Galena and sphalerite were observed in quartz vein samples collected at the old prospects. The results of the study indicate that the galena-sphalerite-bearing quartz veins and veinlets are too narrow, widely-spaced, and low in metal values to be economic. Low concentrations of metals in the soil and rock samples, combined with the lack of major mining activity in the past, indicate that the area has a low likelihood for economic development.

Jan 1, 1986

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

By Jr. Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

By Karl C. Dean

The Bureau of Mines studied the precipitation of copper from dilute acidic sulfate solutions using shredded automobile scrap in a rotary drum. The tests established that the scrap in the rotary drum precipitated copper faster and more completely than shredded, detinned, tinplate scrap in a launder, with comparable iron consumption. Although power is required to rotate the drum, the faster precipitation and continuous recovery of cement copper are advantages of the tumbler method. Cost evaluation indicates that the rotary drum method, which uses relatively low-cost and readily available shredded automobile scrap, is competitive with the launder method, which uses relatively high-cost shredded tinplate scrap or detinned shredded cans.

Jan 1, 1968

By G. S. Scott, G. W. Jones

"INTRODUCTION In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, a. control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration.Many of the anthracite fires have been active for years and have progressed considerable distances free their original source.Some of the fires are in inaccessible territory, and it is often impossible to determine with any degree of accuracy their exact location or even the veins of coal that are afire, especially when the fire is in the upper strata and when it is impossible to go underground because of flooded conditions or the presence of an irrespirable atmosphere.In such cases, the only means by which the trend of a fire may be ascertained (as a result of any fire-fighting methods that may have been employed) are the sampling, exanination, and interpretation of the gaseous products coming from the fire area. The most important information desired is to know whether the temperature in the heated area is increasing or decreasing and to determine whether a fire that has been sealed is cooling down to normal mine temperatures or is maintaining its heat or is increasing in intensity due to infiltration of outside air.Interpretation of the analyses of gaseous products from refuse banks on the surface also should be of value in combating such fires. Refuse bank fires, with the additional danger of starting an underground fire through ignition of the outcrop, are by no means unknown in the anthracite coal region, and the causes of such fires are not always apparent. In a few cases the causes have been strongly suggestive of spontaneous origin."

Jun 1, 1938

By D. D. Dornenburg

The effect of changes of atmospheric pressure on methane emissions from extensive worked-out areas of coal mines in several Midwestern States has lone caused concern to State and Federal mining departments, as well as to the operating companies involved. Common mining and ventilation methods employed in mines in these States have resulted in large sealed and unsealed worked-out areas in which considerable quantities of methane are emitted alone both intake-and return-air courses. The common practice is to watch barometric changes very closely and take special precautionary measurer during periods of low barometric pressure. Although the hazard is recognized, mining officials have different opinions concerning the effect of barometric pressure variations on the emission of mine gases. These opinions are based upon scattered personal observations, as no records exist of actual studies to establish such effects.

Jan 1, 1955

By C. Lorimer Colburn

"High explosives are generally shipped in stout wooden boxes of convenient size, which are much sought after by miners and others for miscellaneous uses after they are emptied. The management of most mines has no fixed policy for the disposal of used dynamite boxes and will allow any one to carry them away. Many dynamite boxes are nailed up in the mine buildings or underground to serve as shelves and cupboards. Some are used as receptacles for odds and ends, and others are used in taking samples.Although used explosives containers are so generally put to beneficial service, there is nevertheless an element of danger in their use. Dynamite boxes are particularly dangerous. Very often nitroglycerin exudes from the dynamite sticks and is absorbed by the wood of the box. Such boxes are dangerous because they are very explosive. Although a box that has not absorbed nitroglycerin is safe, yet there is always the danger that a person will get a box that is partly saturated.On account of this danger, all mining companies should use extreme care in giving away used explosives containers. Some one individual who is acquainted with explosives and their peculiarities should act as inspector for every container given away. This job may best be handled by the man in charge of the powder magazines. A box that shows any stain of nitroglycerin should be destroyed by fire. The other boxes that are free from nitroglycerin or dynamite can be used."

Jun 1, 1920

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By D. Harrington, B. W. Dyer

"Two recent occurrences in Western metal mines in each of which 3 men were killed due to breathing fumes from explosives, have aroused keen interest among mining men not only as to the exact cause of such accidents, but also as to possible preventive measures.In sinking the forty five degree incline Marsh *haft near Burke, Idaho, on May 13, 1920, a round of holes containing about sixty pounds of 40 per cent gelatin explosive was blasted by the night shift upon leaving at 11:30 P.M. It was customary for the night shift to leave compressed air blowers open at bottom of abaft until the compressor was shut down slightly before midnight. Presumably this was not done on the night of the lath as the fumes were so heavy in the shaft bottom on the morning of the 14th that at about 8 o'clock, Superintendent Bergen and one of the shaft men, on reaching the shaft bottom, were overcome and fell from the bucket into the sump containing about six feet of water; and when two other men went down in the bucket a few minutes later to investigate, one also fell into the sump and the other was barely able to roach the shaft collar. The three bodies were later on recovered from the sump.At 400 P.M., June 10, 1920, at the Dominion Mine, Colville, Washington, a round of 11 holes containing about fifteen pounds of 60 per cent nitro¬glycerine explosive was blasted in a fifty degree raise about fifty feet above the main tunnel level by the shift going off for the night. in this mine it was the practice not to try to blow out the fumes until just before the shift went to work the next morning, Although no work was being done on the night shift, one of the raise men, curious to ascertain the effect of the shots, about 7:45 P.M., wandered into the mine (which was a tunnel only a few hundred feet in length), and was missed by one of his companions about an hour later. When three men tried to remove the body of the inquisitive miner, two of them were also overcome; ultimately these two and the first man were removed from the point at which all were asphyxiated, which was practically at the foot of themaise."

Jul 1, 1920

By D. L. Pool

To increase metal recoveries and to minimize pollution by improved extraction technology, the Bureau of Mines investigated a hydrometallurgical technique to recover copper, lead, nickel, and cobalt from lead smelter mattes. The metals were converted from insoluble sulfides to soluble chlorides using a HCI-CI2-02 leaching system. Parameters studied in a 50-gallon, glass-lined reactor were the ratio of hydrochloric acid to chlorine, chlorine consumption per pound of matte, oxygen reaction pressure, and temperature. The matte material used contained, in percent, 19.7 Cu, 52 Pb, 2.9 Ni, 1.5 Fe, 0.38 Co, 0.19 As, 0.41 Zn, and 0.12 Cd. Extraction of Cu, Pb, Ni, Co, and Cd ranged from 92 to 98 pct, with concomitant extractions of Fe and As of <0.1 pct. The Cu and Pb were recovered as electrowon metals, while the Ni, Co, and Cd were recovered as mixed hydroxides.

Jan 1, 1981

By Harry F. Weaver

Rivers in industrial and raining areas frequently are contaminated by material dumped into them causing the water to carry in suspension large amounts of silt, which subsequently is deposited alone; the banks and, ultimately on the agricultural lands if the water is used for irrigation purposes. Two common examples of this practice are the dumping of breaker refuse in the anthracite region of Pennsylvania and the dumping of tailings from the metallurgical mills in various metal-mining districts. Studies in stream pollution and its resultant problems are very important, and surveys are constantly being made by Federal and State agencies, as well as by private companies, to determine the quantity of solids actually being carried by these watercoarses. These studies require accurate sampling of the silt-carrying water to determine the amount of solids within reasonable limits. A device that will obtain reasonably accurate samples of material from silt-bearing streams is described in this circular.

Jan 1, 1943

By Oliver Bowles

[In an endeavor to promote greater efficiency in the lime industry, the United States Bureau of Mines is preparing a series of preliminary reports dealing with particular problems of the industry. Through the circulation of these reports, it is hoped that sufficient interest may develop among lime-plant operators to prompt them to discuss with the bureau their our experiences with these problems. By such an interchange of ideas, it is believed that conclusion may be reached which will be of practical benefit to try entire industry. The first report, "Stripping problems it Limestone quarries of the Shenondoah Valley", Serial No. 2401, was issued during October, 1922. This report t is the second of the series. It is hoped that may operators will contribute additions to the information now at hand.]

Jan 1, 1922

By Herbert R. Appell

Urban refuse, cellulosic wastes, and sewage sludge have been converted to heavy oil by heating under pressure with carbon monoxide and steam. Conversions of the organic matter to oil, water, and gas have averaged near 90 percent at temperatures of 250° to 400° C and pressures of 1,500 to 5,000 psi. The yield of oil, based on the dry organic matter of the waste materials, is usually near 40 percent. This is the equivalent of more than 2 barrels of oil per ton of dry, ash-free waste material. The oil from urban refuse and cellulosic wastes has a sulfur content near 0.1 percent. This low sulfur content makes the oil from refuse a desirable source of fuel oil.

Jan 1, 1970

By W. E. Wallace, V. Castranova, P. Hathaway, F. H. Y. Green, E. D. Recad, V. Vallyathan, M. J. Keane

Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modeled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiologic saline. Lecithin adsorbs to the dusts upon incubation at 37º C and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defense system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modeled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica hemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin hemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in this same time; that which is results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.

Jun 1, 1988

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

Information is presented on remote sealing of a mine passageway through a borehole by five methods : PPnneeuummaattiicc injection of mineral wool and sand, ureaformaldehyde foam , balloons , urethane foam, and caving by blasting . An adaptation of the method using pneumatically conveyed mineral wool was tried in an operating mine . Further research is needed to simplify and to improve the techniques involved , as well as to explore the possibilities of other methods and combinations .

Jan 1, 1964