Search Documents

To develop a cost-effective tool for improving the performance of rock drilling systems used in detecting and delineating underground mine voids and for coal exploration. Approach To investigate admixtures of polyethylene oxide (PEO) at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life in rock drilling systems. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the surface of the rock being drilled. Laboratory drilling studies have been performed on rock types such as quart¬zite, granite, taconite, and marble. The lab tests were conducted using 5/8-inch diameter diamond-impregnated coring bits with cationic compounds as the surface charge neutralizing additives. These studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition.

Jan 1, 1991

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

As the use of deep -rut mining increases, there - expected to be a greater demand for methane (CH,) measurement devices capable of scanning working faces al depths in excess of 10 m to alert mine personnel of hazardous concentrations of CH and to satisfy regulatory requirements. Remote optical devices offer the most promise to satisfy these objectives while the operator remains safely under supported roof. A second¬-generation remote Optical methanomeor (ROM) bas been designed and Is undergoing laboratory evaluation at the National Institute for Occupational Safety and Health. It operates on the principle of differential absorption of the "u;' fundamental absorption band of CH, centered at 3.31 um in the infrared region of the spectrum. The new instrument differs from the previous prototypes by the replacement of the two hand pass differential absorption technique of measurement with a single filter gas correlation technique and a refinement of the amplifier and gating circuitry used within the unit. This results in a more accurate isolation of the CH, spectral absorption band centered at 3.31 um. A specially designed 0.4m-diam variable-length gas mixing tunnel was constructed and instrumented with CH4 sampling capability to calibrate the ROM. Experiments have demonstrated the ability of the detector to respond to various conditions of CH, (pn•m) at distances as great as 12 m. Thermal radiation generated within the instrument is the controlling factor in the drift of the output signal nod, therefore the reliability of the instrument. Several approaches to reduce this extraneous radiation interfering moth the infrared detector, described, such as the installation of a fan in the instrument and thermoelectric coolers on the detector's beat sink. Implementation of this technology will significantly improve the safely of miners.

Jan 5, 1997

By E. M. SEELEY, F. S. LOTT

Expansion in total capacity of the natural-gasoline industry.to produce light products continued in 1944 and 1945. The average rate of gain, however, was reduced to about 6 percent annually from over 9 percent in the preceding 4-year period. New facilities at cycle plants again accounted for most of the increase in productive capacity. Between January 1, 1944, and January 1, 1946, the number of cycle plants increased from 32 to 37 and their total capacity from 3,278 thousand gallons daily to 4,848 thousand (48 percent). Capacity of all other plants in the industry increased in the same period from 12,735 thousand gallons daily to 13,080 thousand, or only 3 percent. The capacity of the average plant increased to 28,600 gallons a day from 24,400 gallons on January 1, 1944, continuing the established trend. The average capacity of cycle plants increased to 131,000 gallons a day from 102,400 gallons, and the average capacity of all other natural-gasoline plants increased to 22,200 gallons a day from 20,400 gallons. Although the number of plants increased in only three States in the 2-year period (Texas, Okla- homa, and Arkansas), the total capacity of plants increased in eight States. A further decline of 29 reduced the total number of plants to 626 on January 1, 1946. Compared with 10 years earlier, gasoline plants were more numerous in only 4 States: Texas (48 more), New Mexico (7 more), Arkansas (2 more), and Louisiana (1 more). The largest declines, in order, were in Oklahoma, Illinois, Pennsylvania, West Virginia, and California. The number of plants with fractionating equipment for separating the liquefied gases from heavier fractions was 202 on January 1, 1946 and 182 2 years earlier. The principal changes in number and capacity of shut-down plants were an increase in Texas and a decrease in California. Shut-down natural-gaso- line plants are usually among the smallest units in their vicinity.

Apr 1, 1947

By Marilyn Biviano

This analysis was conducted in response to concerns raised by the Chairman of the Energy and Commerce Committee of the House of Representatives regarding the potential impacts on automobile production, GNP and employment resulting from embargoing south African supplies of the platinum-group metals, platinum and rhodium. This analysis should be considered an addendum to the recently released study in which the direct economic costs I of a U.S. embargo on selected South African strategic and critical materials are estimated. The estimated GNP and employment impacts result when a mineral shortage reduces domestic industrial production and are in addition to the direct costs estimated in the earlier study. The direct cost to this nation resulting from a decision to embargo six south African strategic and critical minerals was estimated at $1.85 billion per year during the 1988-1992 time frame of the study. The estimated direct costs include the costs to U.S. consumers resulting from higher strategic mineral prices, lower mineral consumption, and the cost of developing higher cost domestic mineral resources. A large proportion of the costs result from the shortage of the two metals: platinum and rhodium. The average direct annual cost of embargoing is estimated at about $1.4 billion for platinum and $384 million for rhodium.2

Jan 1, 1988

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By M. J. Brnich

The purpose of this U.S. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction delivered on either the Draeger OXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the donning task transferred.

Jan 1, 2010

By F. L. Klinger

CRUDE OIL refining continued to be the foremost industry of Bahrain in 1963. This island, the largest of a group 30 kilometers off the Saudi Arabian coast, is the site of the first petroleum discovery in the Persian Gulf and in the Arabian peninsular region. The island's only oilfield was discovered in 1932; exports of crude began in 1934 and the refinery was built in 1936. Although its crude oil has been less than 1 percent of annual Middle East output in recent years, Bahrain has been an important refining center for many years, processing a substantial portion of Saudi Arabian petroleum as well as all local production. The Bahrain refinery annually accounts for 17 percent 0 the petroleum products produced in the Middle East and 25 percent of the exports. Bahrain's mineral resources consist of oil, gas, and basic construction materials. Petroleum production and refining are the important mineral industries and contribute most of the national income by payments for taxes, wages, and local services including construction and material supply. The petroleum industry has supported a large share of local business and extensive indirect employment, and its early establishment also helped Bahrain to strengthen its position as a trading center in the Persian Gulf. The country's entrepôt trade produces about 20 percent of Government revenue, and Bahrain is somewhat less dependent on the petroleum industry than are the neighboring States to the west.

Jan 1, 1964

By Peter J. Clarke

Afghanistan's mineral industry continued to be dominated by the production and export of natural gas, although several mining and related industrial projects, all under the supervision of Soviet technicians, were in the planning stage in 1982. Afghanistan produced minor quantities of barite, cement, coal, fertilizer materials, iron, and lapis lazuli, all for domestic consumption.2 Large-scale projects being investigated were a copper mine and concentrating plant at Ainak, extensive mining of the Hajigak iron ore deposit near Kabul, construction of an oil refinery at Angot, increasing production and processing of natural gas, and implementing an intensive geologic prospecting and exploration program for areas of mineral potential. Afghanistan's gross domestic product (GDP) was estimated at $2.76 billion3 and has remained stagnant for the past several years. Total exports in 1982 were estimated at $700 million, only a marginal increase from the 1981 figure of $694 million. Exports of natural gas to the U.S.S.R. earned $385 million in 1982, representing just over one-half of Afghanistan's total exports. Natural gas revenues were down approximately 11% from the 1981 level, owing primarily to increased antigovernment activity in the northern part of the country.4 About 90% of the country's natural gas production was exported to the U.S.S.R.5 About 38% of Afghanistan's development budget had been earmarked for mining and industrial projects in 1982.6

Jan 1, 1984

By T. G. Mayhew, A. A. Bergeron, R. J. Mahany

This report describes an operational communications system which provides remote intra-terrestrial wireless transmission of environmental information. Design and modification specifications of requisite equipment are included along with a detailed description of system operation

Jan 9, 1976

By J. H. Maysilles

The Bureau of Mines is examining a variety of low-grade uranium ores because projections indicate that an appreciable percentage of future U.S. uranium production will be derived from resources containing 0.01 to 0.1 percent U308. One possible source is represented by a granitic material from Wyoming; the available samples contained 0.06 and 0.12 percent U308. Tests were conducted to explore the general leaching characteristics of this potential resource. The material responded to both acidic and alkaline leaching techniques. Conventional acid leaching extracted 93 percent of the uranium in 18 hours; the required acid addition was 50 to 100 pounds of H2S04 per ton of ore, and the oxidant addition was 3 pounds of NaCl03 per ton of ore. The acid consumption continues after maximum uranium recovery has been reached; this effect may complicate heap or in situ leaching with acidic solutions. Some variation in reagent requirements was noted between the two ore samples. Conventional carbonate leaching with strong solutions at 85° C extracted 94 percent of the uranium in 24 hours. These granitic materials also showed some response to dilute carbonate solutions, and the results suggest that the material may be chemically amenable to heap or in situ leaching with dilute carbonate solutions.

Jan 1, 1977

By L. C. IlsLey

The cool drills that have received the approved of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3363, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.

Jan 1, 1938

By Harley A. Coy

This paper, describing the mining methods and practice at No. 2 mine of the American Zino Co. of Tennessee at Mascot, Tenn., is one of a series of papers issued by the Bureau of Mines presenting the mining methods and costs in various districts throughout the United States. Its purpose is to summarize methods recently put into practice whereby increased efficiency has been effected. These improvements have to do principally with mill-hole mining, slushing, contract labor, and bonuses. In general, this paper supplements earlier articles and brings them up to date. ACKNOWLEDGMENTS The author acknowledges the assistance of M. H. Newman, geologist of the American Zinc, Lead & Smelting Co.; of William Black, assistant superintendent of mines; of P. M. Arthur, director of personnel; and of the engineering staff. The paper has been approved by H. I. Young, vice president and manager of operations.

Jan 1, 1930

By L. C. IlsLey

[The cool drills that have received the approval of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and. (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3303, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.]

Jan 1, 1938

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971

By E. A. Johnson

As part of its effort to reduce the environmental impact associated with mining and metallurgical operations, the Bureau of Mines used a modified form of the Environmental Protection Agency's Extraction Procedure toxicity test on copper reverberatory slags that contained low, medium, and high levels of the impurity elements As, Pb, Sb, Bi, and Zn. All tests resulted in extracts that did not exceed those limits published in the May 19, 1980, Federal Register; there-fore, these solid wastes were designated as nonhazardous for most landfill disposal situations. However, arsenic and lead levels disturbingly close to the allowable limits--and even higher levels of copper and zinc, for which there are no established limits--leached from the high-impurity-element granulated slags. These slags should be handled in such a way so as to minimize the possibility of water contamination. One baghouse dust was tested according to the EPA procedure and found to exceed the extract limits by a factor of 10. This solid waste may be considered hazardous.

Jan 1, 1982

By F. E. Griffith

Cost data are given for five methods of secondary backfilling of strip mines previously partially backfilled. The operations were conducted in north-central Pennsylvania; an average of 600 linear feet of highwall were backfilled in each trial. Major obstacles and the relative merits of the methods are discussed.

Jan 1, 1966

By J. J. Demeter

A tube-wall reactor with a Raney nickel catalyst deposited on the outer wall of the tube by flame spraying is effective in the practically complete conversion of 3H2+1CO synthesis gas to a high-Btu gas (methane) at an hourly space velocity of 7,000 volumes of gas (NTP) per hour per volume of annular volume. Partially reacted synthesis gas containing an appreciable amount of methane can also be treated in this reactor to increase the heating value to over 900 Btu per cubic foot. Excellent heat removal through the metal wall to a coolant and temperature control were obtained. The heat transfer co-efficient from the catalyst to the coolant was about 275 Btu per hour per square foot per ° F. Synthesis tests were conducted with tubes 1.2 inches in ad by 6 inches long, and 1.3 inches in od by 36 inches long. When operating at a synthesis gas rate of 100 to 120 scfh per square foot of catalyst-coated tube, catalyst life was long enough to realize a catalyst cost for the raw Raney nickel alloy of about 0.3 cent per 1,000 cubic feet of pipeline gas (900 to 950 Btu per scf). Gas recycling at ratios of 1:1 to 3:1 was effective in increasing conversion and in extending the life of the catalyst to about 16 weeks. In cost and in operating characteristics the tube-wall reactor compares favorably with the fluidized-bed and hot-gas-recycle reactor systems for the synthesis of high-Btu gas from H2+CO.

Jan 1, 1967

By A. W. Deurbrouck

This report presents the results of a washability study of 322 coal mine samples showing the sulfur forms and distribution in the coals. The samples were collected from mines which were principally utility coal producers. Generally, the data show the total sulfur content of the coals evaluated could be significantly reduced by some combination of stage crushing and specific gravity separation. However, few coals could be upgraded to a final product containing 1 percent or less total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds.

Jan 1, 1972

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005