Search Documents

By Dennis R. Dolinar

The danger to personnel, equipment, and pillar structure created by the spalling of a coal rib can be minimized by installing rib bolts. To assure that a configured support system will maintain a coal rib, the U.S. Bureau of Mines developed a rib bolt system based on a nonpreventable failure concept. A statistical equation quantitatively relates the amount of rib retained to the bolt spacing and the width of the spalled material. Laboratory test results show that the equation accurately predicts the amount of material retained and confirm the validity of the support concept. The examination of rib bolting at a coal mine experiencing rib sloughage provides evidence that the effectiveness of the support can be related to the failure pattern of the spalled material. An analysis of roof and roof support reaction to rib sloughage at the mine indicated that the rib sloughage had little effect on roof stability. Although supporting ribs might not affect roof stability, laboratory test results indicate that the material retained by the support can sustain a load up to 20 pct of the intact compressive strength of the material.

Jan 1, 2010

By C. C. Shale

Electrical resistivities for various coal ashes in air and in a nitrogen atmosphere are given over the range 100° to 1,500° F. Resistivity of low-carbon ash in air is very high at low temperature, rises to a maximum at about 250° F, decreases very rapidly with increasing temperature to about 800° F, then decreases gradually to approach an asymptote at 1,500° F. Resistivity of high-carbon ash in air follows this same general trend at values which are much lower and are proportional to the carbon content. After the carbon has been burned off, resistivity of the remaining ash approaches the high values corresponding to low-carbon ash of similar chemistry. Two factorial experiments show the effects of temperature, particle size, chemical content, and compressibility on the resistivities of four fly ashes of widely different chemical composition in the temperature range proposed for coal-fired turbines. Resistivities of all low-carbon ashes tested fall in the range 106 to 107 ohm cm at 1,500° F and should be removable by electrostatic precipitators. Ashes containing carbon in excess of about 8 percent, however, have low resistivity (as determined in nitrogen), especially at high temperatures. Therefore, high-carbon materials may not be collectable in precipitators because the resistivity is below the minimum value necessary for precipitation. Consequently, high carbon residues from partial combustion of coal probably could not be removed effectively at high temperatures.

Jan 1, 1968

By R. R. Schehl

The Bureau of Mines has developed a quantitative Analysis for pyrite in coal by X-ray diffraction that can be accomplished in little more than 1 hour. To minimize the sample analysis time, data processing has been completely computerized with pertinent output information displayed on a VR12 cathode-ray tube display. Use of this computerized system is not only advantageous during the experimental stages of the pyrite analysis project but would also be essential if the X-ray diffraction procedure is accepted as a standard method of analysis.

Jan 1, 1973

By Foster Fraas

The dielectric constant .has been frequently referred to as an important property in electrostatic separation whore the particles are in an air ambient. Hatfield (1) has studied the problem on the basis of fundamental theory, with the conclusion that separations in air dependent on the differences in dielectric constant, in conjunction with a nonhomogeneous field, are not feasible, because of the low dielectric strength of the air. Although Hatfield has made the statement without showing the calculation or data, calculated values substantiating this under certain conditions of the problem will be given in the following text. However, under other Conditions, these conclusions do not hold, and it is probable that the dielectric constant is indirectly influential.

Jan 1, 1948

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By R. W. Freedman

The gas chromatographic method, devised by the Bureau of Mines for analyzing routine mine air samples, was compared with the infrared method used for confirmatory determination of methane in mine air. While maintaining the specificity of the infrared method for methane determination, the gas chromatographic method is more precise, much more rapidly performed, and more convenient.

Jan 1, 1968

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By M. G. Zabetakis

At ordinary temperatures and pressures methyl ethyl ketone (MEK)-air mixtures containing between 2.0 and 11 vol.-pct. MEK and methyl isobutyl ketone (MIBK)-air mixtures containing between 1.5 and 7.5 vol.-pct. MIBK are flammable. However, MEK-bromochloromethane (BCM)-air mixtures containing at least 6.2 vol.-pct. BCM and MIBK-BCM-air mixtures containing at least 7.0 vol.-pct. BCM are nonflammable. Also, MEK-BCM-air and MIBK-BCM-air mixtures containing less than 18.7 vol.-pct. oxygen are nonflammable. To assure the formation of nonflammable mixtures when mixed with air, MEK-BCM vapor mixtures must contain at least 1.6 vol. BCM per volume MEK, and MIBK-BCM vapor mixtures must contain at least 2.8 vol. BCM per volume of MIBK; these quantities of BCM would be produced by liquid mixtures containing 55 vol.-pct. BCM in the first case and 60 vol.-pct. in the second. An MIBK-BCM-trimethylene chlorobromide mixture containing equal volumes of each liquid forms nonflammable mixtures with air at ordinary temperatures and pressures. The same is true of a liquid mixture containing 34.6 pct. (liquid volume) BCM, 34.b pct. perchloroethylene, 15.4 pct. MIBK, 7.7 pct. toluene, 3.85 pct. ethyl amyl ketone, and 3.85 pct. trimethylene bromide.

Jan 1, 1960

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992

By Lorenz E. Sieffert, Lawrence B. Berger, H. H. Sehrenk, Ralph W. Stewar, James A. Gale

"INTRODUCTION The purpose of the investigation discussed in this article was to evaluate the toxic hazard from gases produced when thermosetting plastic materials used for electrical insulating purposes are burned or thermally decomposed in enclosed spaces. For brevity the term ""toxicity"" is used throughout the article to refer to the nature of gases produced under these conditions. A need for immediate study of the problem was created as a re¬sult of the battle damage reports received from various United States Fleet units. These indicated that the fumes emitted when these materials were burned or thermally decomposed had, in several instances, resulted in toxic atmospheres. In attempting to develop a suitable test method for evaluating toxicity, it was recognized that no single test procedure could be expected to duplicate the variety of conditions that might exist in an actual fire aboard ship. In view of the immediate need, however, it was felt that considerable information could be obtained, at least to classify comparatively the several types of materials as to the toxic effect caused by burning or thermal decomposition, through the development of a sound empirical method which could be applied to all of the materials. On this basis, it was decided to modify the Navy flame resistance test for thermosetting plastics to render it applicable to the determination of the toxic, gases evolved when this test was employed. A wide variety of materials was tested, both molded and laminated, to cover the types commonly used by the Navy in electrical applications. Toxicity determinations were conducted at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Parallel tests, to determine the flame resistance of the materials, were conducted at the Material Laboratory, U. S. Navy Yard, New York, N. Y."

Oct 1, 1947

By E. W. Dean

In the early winter of 1919 the Pittsburgh petroleum laboratory of the Bureau of Mines undertook the work of testing fuel oil samples representing purchases of the United State Shipping Board for ships sailing from the port of New York. fuel oil was, at this time, being bought on a contract which involved specifications issued by the United States Navy under dace of October 2, 1920 (See Bulletin 1, Oil Division, U. S. Fuel Administration.)The object of the Bureau of Mines in undertaking this inspection work was twofold. (1) The Bureau was in position to give, and the Shipping Board needed, reliable laboratory service for checking the quality of the fuel oil purchased, the value of which ran into millions of dollars for,year's supply. (2) It was believed, and later demonstrated, that the existing specifications did not insure the obtaining of a reliably satisfactory quality of oil.The objection to the specifications concerned the employment of a clause limiting the gravity of the oil. The inadequacy of gravity specifications for several types of petroleum products has long been recognized, and there was every reason to reason to believe that they were no more desirable for fuel oil than for gasoline, kerosene, or lubricating oil. A first and obvious objection was the fact that it is somewhat difficult to make accurate gravity tests on ""heavy"" residuum fuel oils. (The Bureau found it necessary to employ or such tests a rather tedious procedure involving the use of a picnometer and an accurate balance, as the simpler methods, employing hydrometer or displacement balance, proved unreliable in a large proportion of cases.) A second and more important objection was that gravity tests, even when accurately made, do not provide a reliable index of the actual quality of the oil.

Feb 1, 1921

By Robert A. Jankowski

Through laboratory and underground studies, the Bureau of Mines has evaluated the use of passive barriers (dust shields) to help confine dust generated by longwall shearers to the face area. Laboratory studies focused first on selection of the optimum barrier design, which proved to be a simple, gobside barrier (made of conveyor belting), coupled with a headgate splitter arm, which was found necessary to prevent the dust cloud from entering the walkway at the headgate end of the shearer when cutting tail to head. Further laboratory testing was done to determine whether using passive barriers in combination with different water-spray dust-reduction methods, including the shearer-clearer system developed by the Bureau, would improve dust reduction over that from using the water sprays alone. It was found that the combination of gobs ide passive barriers plus the full shearer-clearer system was most effective, and surmised that this would be especially useful in thicker seams. However, underground testing revealed that the shearer-clearer system alone was 35 pct more effective in reducing dust contamination than when used with the gobside passive barriers, and far more effective than using passive barriers with a conventional water spray system. For such an effective system as the shearer-clearer; the reduction in avail-able space over the top of the machine actually impeded system performance; this was shom1 in both eastern and western mines. But when used with comparatively inefficient water spray systems, the passive barriers, used in combination with a headgate splitter arm, provide consider-able help in reducing dust levels in the walkway.

Jan 1, 1986

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX D DEVELOPMENT AND EXPERIMENTAL VERIFICATION OF ACOUSTIC SEAL CHECKER THEORY 1. Introduction In Section 7 of the report the acoustic seal checker concept was described in a general manner and the parameters which affect the signal level at the microphone were discussed briefly. In this appendix the theoretical basis will be presented and the experimental program described which permitted the extension of the theory into practice. The basic goal of the acoustic seal checker is to relate the reduction in sound pressure level to the size of the residual hole in the fly ash barrier. The smallest hole size that may be measured is determined by the signal to noise ratio, where the noise in this case includes the ambient noise in the mine, the internal microphone noise and the sound transmitted from the acoustic source via the flanking paths through corridors adjacent to the one being sealed. The latter source of noise can be discriminated against, at the expense of increased complexity of the acoustic system, by employing a pulsed source and pulse gating of the microphone signal set to accept sound via the barrier path and to reject the delayed flanking path signals. In order that the acoustic system be insensitive to precise source and microphone location and to permit assessment of system performance on an acoustic power flow basis, a broad frequency band of pseudo-random noise is emitted by the loudspeaker source. The preferred frequency range must be determined, the advantage of a directive source must be assessed, and the necessity

Jan 1, 1973

By R. W. Watson

This Bureau of Mines report summarizes some recent results on the sensitivity of various experimental explosive systems using ammonium nitrate (AN) as the oxidizing agent. The sensitivity survey included drop-weight and friction testing and sensitivity to initiation by projectile impact and a No.8 blasting cap. It was found that certain types of AN prills can result in cap-sensitive mixtures when combined with No.2 diesel fuel (Fa); prilled AN mixed with nitromethane also result in cap-sensitive mixtures. Mixtures of AN prills and neat 1-and 2-nitropropane were not cap-sensitive, and the use of powdered or grained aluminum in AN-FO did not adversely affect the sensitivity except possibly to increase its sensitivity to friction.

Jan 1, 1974

By Sidney Katell

Continuing the series of cost bibliographies which was initiated with the publication of Information Circular 7516 in October 1949, the present report covers the period from January 1959 through December 1959. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, were obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil. On Oct. 16, 1959 a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers became effective. This agreement provides for the publication of the annual bibliography under the sponsorship of both groups with the work load involved in the preparation divided equally between the two. As a result, the present report partially reflects the efforts of the members of the Association.

Jan 1, 1960

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

The National Institute for Occupational Safety and Health (NIOSH) National Personal Protec-tive Technology Laboratory (NPPTL) and the Mine Safety and Health Administration (MSHA) conduct a Long Term Field Evaluation (LTFE) program to evaluate deployed self-contained self-rescuers (SCSRs). The objective of the program is to evaluate how well SCSRs endure the under-ground coal mining environment with regard to both physical damage and aging when they are deployed in accordance with Federal regulations (30 CFR 75.1714). This report presents ?ndings of the combined eighth and ninth phases of the LTFE. For these phases, over four hundred SCSRs were evaluated. The units tested include the CSE SR-100, Draeger Oxy K-Plus, MSA Life-saver 60, and the OCENCO EBA 6.5. The OCENCO M-20 was evaluated only in Phase 9. Testing was per-formed between December 2000 and April 2004. Results of the evaluation indicate that all SCSRs experience some performance degradation due to the mining environment. Observed degrada-tion varies from elevated levels of carbon dioxide, high breathing resistance, and reduced capacity. Mechanical degradation to the SCSR components included breathing hoses, chemical beds, outer cases and seals. The LTFE tests discussed in this report are different from tests performed for SCSR certi?cation to the requirements of 42 Code of Federal Regulations, Part 84 (42 CFR, Part 84). LTFE tests reported here are conducted to an end point, oxygen depletion, to enable comparison of the duration of new and deployed SCSRs. The method for obtaining deployed SCSRs for this evalua-tion was not a random selection from the deployed population of SCSRs. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the generalizability of the results. This program will be implemented following completion of Phase 10 of the current LTFE protocol.

Jan 10, 2006

By J. A. Lamonica

The Bureau of Mines studied two types of approved coal mine dust personal samplers to determine the effect of decreasing the amplitude of airflow velocity fluctuations on cyclone performance. Results indicate that more dust is collected when pulsation free flow is used. Velocity fluctuations were reduced by means of a pulsation damper; damper efficiency of about 85 percent was needed to reduce the fluctuations to an acceptable level. The data were obtained employing both pulsating and non-pulsating flow. A comparison was made of (1) the masses of respirable coal dust as determined by weighing and of (2) the particle size distributions as determined by an electronic counter. An empirical relationship is given between the ratio of masses collected using pulsating and nonpulsating flow (M') and the ratio of the maximum air velocity to the minimum air velocity (V') as measured in the cyclone entrance channel.

Jan 1, 1972

By R. V. Ramani, C. B. Manula, A. Owili-Eger

All the input data required to operate the ventilation simulator except the title, are entered with I10 or F1O.O formats. The title is entered with (18A4) format. The floating points are designated by (FP) and the integers by (INT)

Jan 1, 1975

By C. V. Davis

In the lnvestlg::ìt1on of mAthods for aSS8.7ing platin",. conducted by the Bureau ot MinAs, reoent experiments have d~velopad tha~ with ce..tain orei, especially when thr, quantity Of platinum 1s eonlidarablfl, nit'!le acid w111 not etfßct a iepard-Han of platinum and pa11adium. 'lhe following m;lthod has been found to be accurate and to reiu1 t in a complete S''lun''ation of' th~3:l metals. It is therefo 1" '!eeommei:ed that 1 t ba followed rath::r- than the method of separation with nitrio acid, givèn in Technical Pape'! 270.* At line 22, pagi 14, of that paper, bAglnnlng with ~tarm th,~ metals '.'ith dilute¡ nitrio acid," strikE out the rest of the paragraph, and substttutt~ the pro_t cedure g1 ven below. ?lunder and Thuringer.. have developed mnt¡iods for th"i sflparation of palladium from all the platinum metals exoept platinum bj m ,ans of dlmethy- 19lyoxlme. They state that the~ is no action for several hours if an excess of dimeth¡lglyoxime is added to an aqueous solution of ohloroplatinic acid in the cold, alio that only on boiling is the platinum pTecipi ated ¡~d than only PST't of the platinum i srenoved from the sUut1on. They found that palladium 1s p~ecipi tated quati tat! vely in the oold as (CaH 4N40 Pd) which is insoluble tn water, dilute hydroohlorio acid, dilute acetIc aofd or in 50~ ethyl alcbhol. All of their pT'90ipi tations we~p Carl". ied out ~hile the solutions were being heated. This caused a pal"tia~recipltation of the platinum along wi th the

May 1, 1922