Search Documents

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980

By Gregory Krohn

This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners. The first study showed that added glove padding provides more potential protection but does not affect manual dexterity. The second study, in a simulated low seam coal mine, showed no significant differences using padded and non-padded gloves in crawling, shoveling, timbering, and cart pushing task completion times. In general, subjects preferred the padded gloves although they expressed some complaints about awkardness and loss of sensitivity. Recommendations are given for the design of padded gloves that will provide comfort, protection, and maximum hand sensitivity for miners.

Jan 1, 1980

By L. C. IlsLey

In the normal operation of mines, the aggregate effect of many seemingly minor op rations may be very important as respects economy and safety. Anion: these operations is the method employed in coupling and uncoupling mine cars. For economic reasons the equipment in mines has not been protected as well as railroad equipment. It is pertinent that haulage accidents rank second in severity among mine accidents, and that manual coupling of cars has been one of the most frequent causes of such accidents. One study4/ revealed that coupling was responsible for about 20 percent of haulage accidents underground. A review of early conditions on steam railroads, which were responsible for the introduction of safer methods of coupling cars, indicates how conditions in might be improved. THE STORY OF RAILROAD COUPLING As any considerable improvement in mine-car coupling probably will follow lines somewhat similar to those that brought order out of chaos for the railroads, it seems appropriate to review briefly the steps taken to improve railroad coupling from the days of link and pin couplings of various types to the adoption of the standard ?M.C.E? automatic coupler.

Jan 1, 1943

By Kenneth M. Earl

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the Tapley deposit in an endeavor to find an additional source of copper. There are accounts that many years ago the property had some production; there are several old, inaccessible shafts apparently sunk on a vein in rhyolite or diabase. The waste dumps of these shafts contain considerable sulfides, chiefly pyrite and chalcopyrite. To cut the vein below the old mine workings, the Bureau of Mines? diamond-drilled five holes aggregating 1,204 feet. No significant copper mineralization was found.

Jan 1, 1950

By John S. Dunning

This is one of a. series of papers being prepared for and published by the United States Bureau of Mines, describing raining and milling methods at crushed-stone plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in man; instances cause embarrassment to individual producers as well as to the industry as a whole. However, operating costs are essential to technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that the scope of the cost tabulations shall not be misunderstood. This paper deals with the quarrying and crushing methods used at the Avon Mountain trap-rock quarry of the Atlas Sand, Gravel & Stone Co., in West Hartford, Conn.

Jan 1, 1936

Develop a user-friendly computer program that permits those interested in mine health and safety to access and analyze on a personal computer (PC) employment, production, and accident data for U.S. coal and metal-nonmetal mines. This software is being designed with a major focus on flexibility and case of use. The Mine Accident Decision Support System (MADSS) will be available for distribution in mid-1994. Currently, the U.S. Bureau of Mines (USBM) is seeking volunteers willing to pilot test a preliminary version of the software and to provide suggestions for its improvement. Background Since 1975, the Mine Safety and Health Administration (MSHA) has compiled large data bases of information about U.S. mines and the reportable accidents, injuries, and illnesses that have occurred in those mines. Employment and production data arc collected on a quarterly basis from each mine and accident information is collected on an incident -by-incident basis. The USBM has compiled estimated costs for each of these accidents using computer models. All of this information is potentially useful to mine health and safety researchers. However, it has been underutilized because it is stored in large mainframe data bases that arc inaccessible to many users and/or are cumbersome and difficult to use.

Jan 1, 1993

By W. S. Anderson

The use of flexible liners for support of underground openings has been investigated by the Bureau of Mines. This report presents installation procedures and instrumentation results of a full-scale flexible liner field installation in the Burgin mine. The flexible liner is a part of the mine support system and has provided maintenance-free support for 22 months

Jan 1, 1975

By Thomas V. Falkie, R. Venkataramani

Anderson, L. B., 1963, "Multiple Regression Techniques Correlate Experimental Data," Chemical Engineering, V. 70, N. 12, pp. 223-228. Aubert, E. J., Lund, I. A., and Thomasell, A. J., 1959, "Some Objective Six-Hour Predictions Prepared by Statistical Methods," Journal of Meteorology, V. 16, pp. 436-46. Barrett, A. L., 1958, "Alternating Current in Continuous Mining," Mechanization, V. 22, N. 9, pp. 83-86. Bower, A. B., Jr., 1970, "Bit Design: Key to Coal Cutting," Coal Age, V. 75, N. 7, pp. 70-72. Bower, A. B., Jr., 1971, Personal Communication dated April 29, 1971; General Electric Company, Mining and Metallurgical Products Department, Detroit, Michigan. Burt, C., 1950, "Group Factor Analysis", British Journal of Statistical Psychology, V. 3, pp. 40-75. Cady, L., Gertler, M., Gottsch, L., and Woodbury, M., 1961, "The Factor Structure of Variables Concerned with Coronary Artery Disease", Behavioral Science, V. 6, pp. 37-41. Cattell, R. B., 1965, "Factor Analysis: An Introduction to Essentials I. The Purpose and Underlying Models," Biometrics, V. 21, N. 1, pp. 190-215. Christensen, R. W., Heins, R. W., Babcock, W., and Tonn, R., 1971, "The Effect of Material Properties on Materials Handling Processes," Six Month Technical Report, (August 1971) to Advanced Research Projects Agency, U. S. Department of Defense; The University of Wisconsin. Collins, G., 1961, "Factor Analysis," Journal of Advertising Research, V. 1, N. 5, pp. 28-37. Cooley, W. W., and Lohnes, P. R., 1962, Multivariate Procedures for the Behavioral Sciences, New York: John Wiley and Sons, Inc. Cree, J. 0., 1956, "Power for Continuous Mining," Mining Congress Journal, V. 42, N. 10, pp. 49-52. Draper, N. R., and Smith, H., 1966, Applied Regression Analysis, New York, John Wiley & Sons, Inc. Griffiths, J. C., 1966, "A Genetic Model for the Interpretive Petrology of Detrital Sediments," The Journal of Geology, V. 74, N. 5, pp. 655-672.

Jan 1, 1972

By D. M. Soboroff

Etchants containing hexavalent chromium and sulfuric acid are used in a variety of surface-finishing operations. When the resultant spent solutions are discarded, substantial quantities of chromium are lost and pollution prob¬lems are created. To minimize the undesirable environmental effects while improving metal and minerals recycling technology, the Bureau of Mines is conducting research on a method for the economic inplant recycling of these waste etchants. Trivalent chromium, produced when the etchant reacts with a sub¬strate, is oxidized in the anode chamber of a diaphragm cell; other metals, dissolved during the etching operation, are transferred to the catholyte. When waste brass etchants are treated in this manner, all of the trivalent chromium is oxidized and more than 40 percent of the copper and zinc is removed. Similar copper removal and chromium oxidation are achieved with waste printed circuit board etchants and rinse waters from plastic etching operations. The electrical energy needed to regenerate 1 kg sodium dichromate is less than 9 kwhr. Regenerated brass etchants evaluated by two companies equaled or exceeded the performance of fresh etchants.

Jan 1, 1979

By M. E. Kundick, W. E. Dieter, L. Cohen

The major details of design and maintenance of a seamless stainless steel fume hood system , developed by the Bureau of Mines , are described and illustrated . Operating and housekeeping routines are outlined .

Jan 1, 1964

By Merle L. Bowser

The Bureau of Mines has constructed a miniature oxygen deficiency alarm system using an electrochemical cell as the sensor. Distinct audible signals are produced at either of two preselectable oxygen levels which can be varied from approximately 10 to 20.9 percent oxygen. The high or cautionary range produces a 500-cycle-per-second tone pulsed at about a 1-cycle-per-second rate, whereas the lower or more dangerous oxygen level produces a continuous 500-cycle-per-second tone.

Jan 1, 1968

By A. Adams

The Bureau of Mines determined the composition of the vapors liberated during thermal decomposition of aluminium nitrate nonahydrate. Small samples were heated from room temperature to 5500 C with initial heating rates from 500 to 2000 C/min. Gases were rapidly swept away from the heated chamber with Ar and subjected to immediate analysis in order to minimize reaction between the components. In addition to H20, four N-containing compounds were identified: HN03, N02, NO, and N20. Nz could not be determined in the presence of the nitrogen oxides, and at-tempted separation from the oxides led to the formation of more nitrogen. Relative amounts of each component were found to vary over a period of time; however, total amounts measured with different heating rates were reasonably constant and were typically as follows: 84.2 pct HN03, 7.1 pct N02, 4.3 pct NO, and 4.2 pct N20. HN03 and NO were determined from chemical reactions with a permanganate solution, N20 was measured with a mass spectrometer, and NO2 was measured with a spectro-photometer. Details of the methods used are described. Since NO2 and NO can readily be converted to HN03, about 96 pct of the N from the decomposition can be recovered as HN03

Jan 1, 1987

By John Durkin

Owing to the daily exposures of uranium mining personnel to 222Rn daughters, a device is needed that will continually monitor individual exposure. Such a device has been built and tested by the Bureau of Mines and is known as a radon daughter dosimeter. This is an electronic instrument using a solid-state detector and circuitry. The concept of the instrument, which is a personal device worn throughout the working shift, is to evaluate an individual's cumulative exposure to airborne radon progeny, expressed in units of working level hours. Since the instrument is in close proximity to the miner and measures continual exposure, it avoids the errors caused by the present technique of spot checking of the environment and provides a more accurate account of total cumulative exposure.

Jan 1, 1977

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 14 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFOUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS. IN ADDITION A CONNECTION HAS BEEN MADE BETWEEN THE MINE UNDER STUDY AND A SHAFT IN A WORKED OUT MINE IN THE 1 FACE AREA. THIS SHAFT IS CONSIDERED AN INTAKE SHAFT FOR THIS RUN.

Jan 1, 1977

Provide ear protection which allows normal, unaltered hearing at low noise levels, yet protects the wearer from excessive noise. The Approach: A commercial earmuff with integral speakers has been adapted with a special amplifier so that low sound levels are not affected, but higher noise levels automatically reduced. How It Works: The discriminating earmuff developed by the Bureau of Mines has two modes of operation. In the first mode, where input sound levels are less than or equal to 83 decibels, the wearer will perceive noise at its actual level. For inputs in excess of 83 decibels, the second mode of operation begins and the sound perceived by the wearer is progressively attenuated, or reduced, as the input level is increased. A recognizable difference still exists between two adjacent sound levels enabling the wearer to differentiate between them.

Jan 1, 1975

By J. J. Forbes

"The central rescue station maintained jointly by several mining com¬panies in a district, is gaining in popularity in a large number of mining districts throughout the country. A very efficient first-aid and mine rescue association, with rescue station, is in operation in 'the Globe-Miami, Arizona, district. This association, known as the ""Globe-Miami District Mine Rescue and First-Aid Association""; was organized on January 1, 1918. Due to the effective work of this organization, several incipient mine fires have been extinguished before the fire got under headway and before any severe damage was done.The mine rescue station, which is situated on the highway between the towns of Globe and Miami, Arizona, is centrally located with respect to the various mines in the district. The station was completed, and a full craw em-ployed for conducting it work on January 1, 1920.The directors and other officers of the association are selected from the mine officials whose properties are served by it. It includes seven large metal mining and metallurgical companies in the Globe-Miami district. The names of the companies, together with the number of men employed by each follows.A director is in charge of the station; he performs the executive work, and, is the managing head of all training in first aid and mine rescue. The director is assisted by three station attendants, one of whom takes the morning shift, another, the evening shift, and the third, the night shift. They exchange shifts every two weeks. As three shifts are maintained, an attendant is on duty at all times. He answers emergency calls in case of fires or accidents, assists with the first-aid and mine rescue training, the inspection of the first-aid boxes and supply bases that are located at the various mines, and attends to miscellaneous duties in connection with the operation and maintenance of the station."

Dec 1, 1920

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity. On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can not be designed to be 100 per cent efficient and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the computed figures of heat requirement per carrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, 'the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil.

Jan 1, 1931

By R. V. Ramani, P. M. T. White, D. Sutton

1.1 General The examination and evaluation of a mineral deposit to determine whether or not it can be profitably exploited entails many factors unrelated to the physical nature and intrinsic worth of that deposit. Nevertheless, geology and geologically related factors have great bearing on the economic potential of the deposit. This is only natural because the deposit owes its existence to these factors. This is even more so in underground mines where the whole system is a geologically enclosed one. Geology plays a major role in at least four phases of a mineral venture. Firstly, it acts as an indicator of the existence of parti¬cular minerals. For example, it is inconceivable that a sedimentary coal deposit would exist in a granitic batholith or stock, or that a sandstone would host primary copper or nickel sulphides. Further, the positional relationship of different rock types may be significant in locating deposits such as replacement zinc and copper sulphides in limestones which have been intruded by igneous rocks. Thus, geology is important in the exploration phase of a mineral deposit. Secondly, once potentially valuable minerals have been discovered, knowledge of geology plays a significant role in determining the dis¬tribution, grade and extent of the mineralization. Controls on mineralization include one or all of those related to structure, rock type, sedimentary features, post-depositional redistribution, etc. Con¬sequently, in order to effectively evaluate a deposit in terms of

Jan 1, 1974

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By John H. Soulé

"INTRODUCTION The Peerless mine was examined by W. R. Storms, an engineer of the Bureau of Mines, on June 2, 1944, in conjunction with a mineral survey of the adjoining For Bayard Military Reservation. Storms again studied the mine on January 13; 15 and 16, 1945, to determine the possibilities of finding new ore reserves to replace these depleted by mining. A project to explore the Peer-less vein at depths below and to the south of the principal mine workings was proposed. Special attention was given to the possibility of exploring favorable beds in the Magdalena and Lake Valley limestones at points near the Peerless fault.The proposed project was approve and exploratory work started on January 2, 1946, and was completed on June 5, 1946. The mine was not in operation during the project, and all equipment had been removed."

Apr 1, 1947