Search Documents

By Daniel Ng

The U.S. Bureau of Mines-Michigan Technological University mine ventilation mainframe program was successfully adapted for execution in a personal computer (PC). The hardware requirement can be as modest as 256 kilobytes (33) of random access memory (RM) and two floppy disk drives. A version compiled for a PC possessing 512 Kb RAM has arrays dimensioned to accommodate 512 separate mine airways and junctions, and it contains all the features and capabilities of the original version. It has successfully analyzed all the ventilation networks tested, including a very large commercial mine (404 airways, 237 junctions, and 5 fans). In all cases the PC version produced practically identical results as obtained from the mainframe computer. In all respects, the PC version performed the same as the mainframe version with the exception of execution speed When a numerical coprocessor is employed, execution time can be reduced by more than 50%.

Jan 1, 1989

By L. Stein

A simplified radiochemical method has been developed for quantitatively analyzing; radon gas in underground uranium mines. In this method, a measured volume of air is drawn by a pump through a drying tube and a cartridge containing dioxygenyl hexafluoroantimonate reagent. Radon is captured as n nonvolatile product. After radioactive equilibrium has been established between radon and its short-lived daughters (approximately 4 hours), the gamma-emission of the cartridge is measured with a scintillation counter. The amount of radon is then calculated from the gamma-emission rate. The effect of cartridge geometry, reagent load, and air flow rate upon collection efficiency and counting efficiency is reported.

Jan 1, 1977

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

[ ]

Jan 1, 1979

By Corale L. Brierley

Beneficiation of phosphate in the southeastern United States generates a slurry of finely divided clay. These clay-wastes are impounded to allow the particulates to settle. The aggregation of phosphatic clay-slime wastes and slimes produced from potash beneficiation by microbial processes was studied using several bacterial species known to produce polymeric substances. Experiments included flocculation capacity of clay-slimes by whole cells, the determination of respiratory activity of whole culls in the presence of phosphatic clays, observation of clay flocculation rates by polymers derived from these organisms, and clarity of polymer-flocculated clay suspensions. The polymer-producing organisms exhibited little capacity for flocculating phosphate and potash clay-slimes. Fungal spores of Cladosporium cladosporioides (isolated from a phosphate clay-waste impoundment), when agitated with clay-slime for several days, caused the clay to form pellets. Separation of the clay/fungal pellets (density 1.1 g ml-1) from the process water might he possible using a screening technique. Studies with C. cladosporioides included the determination of suitable energy substrates and supplements for growth, absorption studies of a pigment produced by the organism, determination of the time required for bioflocculant production by the organism, and an elucidation of the conditions required for the pelletization of clay-slimes by the fungus.

Jan 1, 1982

By Edward A. Barrett, Roberta A. Calhoun

MORE THAN 30 MILLION EMPLOYEES each year are exposed to hazardous occupational noise, and approximately one-third of them develop permanent hearing loss (NSC, 2000). Possible explanations for the latter statistic include worker regard for noise as a mere nuisance rather than as an occupational safety and health hazard, and consequent neglect of established protective measures (e.g., hearing protection); lack of knowledge concerning noise; improper use of hearing protection; worker indifference; and inadequate training (Bauer & Babich, 2004). Many drill rigs generate high sound levels, which vary according to the type of machine, its location with respect to the physical surroundings, and the location of the sound measured around the rig. A NIOSH study measured noise output from several types of drill rigs during field investigations (Ingram & Matetic, 2003). Two types of data were recorded the actual noise generated by the drill rig at various positions around the rig and the noise to which the drill operator was exposed during the drilling cycle. For the latter, sound level measurements up to 120 dBA were recorded while hammering casing (metal on metal) in drilling a water well (Photo 1). Several types of administrative controls exist to address worker exposure to loud drill rig noise. Rotating duties to decrease exposure time and posting warning signs in high-noise work areas are two such controls. Another is the use of hearing protection. Worker use of hearing protection has been disappointing, however. One study by the University of Michigan found that construction workers used earplugs and earmuffs only between 36% and 61% of the time that they were necessary (Lusk & Kerr, 1998). In a 2001 study, OSHA reported a relatively low rate of 30.4% for use of earplugs among construction workers (Walker, 2001). Why are rates for hearing protection use so low? One explanation may be workers' lack of concern for noise in the workplace. They expect workplace noise to be a loud and in¬ evitable nuisance and, therefore, accept it as part of the job. As a result, they disregard proven measures that can protect their hearing. Other workers may use hearing protection, but do so improperly. They may misguidedly remain in high-noise areas for extended periods thinking they are protected when in fact they are not. Other reasons for low use and/or misuse of hearing protection include poor education, lack of awareness and inadequate training (Nash, 2003). To address the training issue, NIOSH developed two exercises from which drillers can learn about noise, hearing loss and hearing protection. The first is an invisible ink exercise, titled "Drill Rig Incident" (DRI) (Photo 2); the second is a 3-D slide reel training aid, "Wearing Hearing Protection Properly" (WHPP) (Photo 3). DRI is an instructor-

By E. G. Davis

This report summarizes an investigation to determine the occurrence and recoverability of heavy minerals in sand and gravel operations in the Southeastern United States. A total of 61 samples from 34 sand and gravel operations in Alabama, Georgia, South Carolina, and North Carolina were studied. Heavy minerals, in amounts ranging from 3 to 400 pounds per ton, were found in all of the samples. Eighty percent of the samples contained 20 to 40 pounds per ton of heavy min¬eral. Valuable heavy minerals, in order of decreasing amounts, were ilmenite, kyanite, zircon, rutile, and monazite. Large-scale concentration tests were made on five samples from four major producers. Gravity concentration by Humphreys spirals and tables resulted in bulk heavy mineral concentrates that graded from 82 to 98 percent total heavy minerals. Mineral recoveries ranged, in percent, as follows: Ilmenite 60 to 95; zircon 96 to 100; kyanite 37 to 77; rutile 89 to 100; and monazite 96 to 100. Separation studies on the gravity concentrates showed they would respond to high-tension and high-intensity magnetic separation techniques to produce individual mineral concentrates. The recovery of each individual mineral from fractionation of the heavy mineral gravity concentrates, in percent, was: Ilmenite 77 to 94; rutile 41 to 68; kyanite 62 to 79; zircon 49 to 83; and rare-earth products, monazite and xenotime, 42 to 96. The grade of each mineral concentrate was: Ilmenite 51.1 to 68.7 percent Ti02; rutile 93.7 to 94.3 percent Ti02; kyanite 55 percent A1203; zircon 58 to 61 percent Zr02; and rare-earth products containing 73.8 to 90.8 percent monazite and 4.8 to 12.7 percent xenotime.

Jan 1, 1971

Illumination hardware developed in conjunction with previous Contracts H024202l, H0242049, and H0242023 had not been adequately tested in actual underground work situations. The purpose of this contract was to install and monitor this equipment on mining machines and in actual working places of coal mines to gain experience with the use of the lamps and support equipment in the abusive and critical environments for which they were intended. The equipment that was to be tested consisted of the following: a. Lamps -A variety of sizes of permissible fluorescent lamps which operate from 12 volts DC power. These include the following sizes: Model 8, (9 watts) 2" diameter; Model 15/2 (14 watts) 2" diameter; Model 15/3 (21 watts) 3" diameter; Model 20 (25 watts) 3" diameter; Model 30, (28 watts) 3" diameter; and Model 40, (39 watts) 311 diameter. Representative photographs of these lamps are shown in Figure 1-1 and 1-2.

Jan 1, 1976

By E. R. Palowitch

Two samples of the Lower Hartshorne (Spadra) bed were collected: A sample of the raw coal with the machine cuttings excluded, and a sample of the machine cuttings exclusively. Analysis of the 5-inch by 200-mesh size fraction of the raw coal, excluding machine cuttings, showed that a product meeting minimum quality specifications could be produced by washing at 1.60 specific gravity, yielding a theoretical 93.7 percent of clean coal. A negligible amount of near-gravity material at the separation gravity indicated an easy washing problem. The sample of machine cuttings had a maximum size of 2 inches and contained about 50 percent ash. Washability tests of the 2-inch by 200-mesh size fraction indicated that a theoretical yield of 30.0 percent of specification-grade coal could be achieved by washing at 1.49 specific gravity. As the machine cuttings represent an estimated 10 percent of the total coal mined, their inclusion in the mine output would increase the theoretical net yield of salable coal by only 3.7 percent. Because the machine cuttings contained a high percentage of sink 1.80 specific-gravity material, they had neither an effect on the separating gravity required to clean the raw coal nor on the difficulty of separation. Gabbing underground versus transporting the cut-tings to the surface for disposal or washing either separately or combined with the raw coal involves a number of practical, economic; and intangible factors; hence, no specific recommendations could be made. A discussion of some of the factors involved in dealing with a similar problem is given by Gandrud and Riley.4

Jan 1, 1962

By Ivor Hawkes

This report describes the results of a study to evaluate new design concepts for percussive rock drills that will result in quieter machines. It is shown that by incorporating such features as an efficient muffler, a plenum chamber integral with the machine body, and shroud tubes around the drill rods, etc., noise levels are reduced from about 114 dBA to about 95 dBA with very little change in drilling performance.

Jan 1, 1977

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

A mobile vacuum sweeper to remove loose coal and coal dust from underground coal mine workings was designed, built, tested, and evaluated. The design was based on an extensive test program. Pick up and conveying rates vs. air volumes, velocities, and nozzle shapes were determined for coal rubble in a laboratory pneumatic handling system. A gas/solids separation system was developed and tested in the laboratory capable of separating the solids loading from the vacuum system air stream to the very high degree required to preclude degradation of the ambient (mine) air. Two designs were made, one for belt conveyor and one for general district cleanup. The belt cleanup machine was chosen for test and demonstrated in an underground coal mine performing cleanup work in belt haulageways and on ribs.

Jan 1, 1975

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By Kevin M. Connor, O&apos

This report documents-the process of literature review, site selection, instrument installation, data acquisition, and preliminary data reduction performed to evaluate the influence of rock mass discontinuities on coal mine subsidence. A system of surface, subsurface and mine level instrumentation was installed at the Armco No. 7 Mine in Montcoal, West Virginia where the overburden varied in thickness from 630 to 1040 feet. Survey monuments, borehole pressure cells, full profile borehole inclinometer-extensometers, mine level extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. Final design of the instrumentation system was based on: a) review of available information, b) field mapping and analysis of areal photography, c) drilling, and d) borehole geophysics. The report contains the complete graphed data of stress and displacements accompanying the longwall mining of a 4800 ft long by 480 ft wide coal panel.

Jan 1, 1983

By J. M. Kurtz

Ten Methane Monitoring Systems and Machine Control Circuits were examined and tested per the requirements in CFR Title 30, Parts 18 and 27, the Standard UL 913 and the document "Test Requirements For Instruments or Apparatus to be Considered for M.E.S.A. Intrinsically Safe Certification (Tentative)". The test results indicate that none of the products complied with all parts of all requirements as interpreted by Underwriters Laboratories Inc.

Jan 1, 1980

By R. J. Traube

The purpose of the Inherently Safe Mining System (ISMS) project is to develop continuous and conventional coal mining equipment and systems which will reduce the incidence of fatal and nonfatal accidents in the working sections of underground bituminous coal mines by application of existing technology. This 3-year program, initiated on 18 June 1971, is being conducted in three phases: ? PHASE I (8 months) Systems Analysis Concept Design Planning ? PHASE 11 (16 months) Design Procurement Manufacture Preliminary Testing ? PHASE III (12 months) Underground Coal Production Demonstration.

Jan 1, 1972