Search Documents

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

By Thomas M. Barczak, Dennis R. Dolinar, Gabriel S. Esterhuizen

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this “uncontrollable convergence” be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffness of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

By Ch. D. Taylor

Past studies with blowing face ventilation systems have shown that using a machine-mounted scrubber and water sprays can reduced methane levels at the face. The current research was conducted to determine how the sprays and scrubber interact to reduce methane levels, and what spray configurations provide the best face ventilation when used with a scrubber. Testing was conducted in a ventilation test gallery designed to simulate a full-scale mine entry. In the entry, a model mining machine, equipped with a simulated dust scrubber and water spray systems, was located at the face of a 6.1 m (20 ft) box cut. Face ventilation was provided by a blowing curtain located 12.2 m (40 ft) from the face. Methane released from a manifold at the face was measured at six locations near the face to compare the ventilation effectiveness of the spray systems while operating with and without the scrubber. Airflow movement across the face was affected by the spray configuration and scrubber operation. Average face concentrations were lowest when directed sprays were used with the scrubber. Varying the direction of the scrubber exhaust affected face methane levels.

By Miyuki Morioka, Michael J. Griffin

Discomfort, annoyance, or interference with activities due to exposure to vibration is only expected if the vibration exceeds the threshold for the perception of vibration. When there is more than one vibration input to the body (e.g. at the hands, seat and feet), the sensation is first experienced at the location with greatest sensitivity. Knowledge of differences in the thresholds of perception for vibration at the hand, seat, and feet should assist the identification of sources of discomfort caused by vibration. Perception thresholds for vibration have been determined in several studies, but only a few studies have investigated perception thresholds in the horizontal direction for hand-transmitted vibration 1, 6 or whole-body vibration 4-5, and there has been little consideration of perception thresholds for the foot resting on a vibrating surface. This study determines absolute thresholds for the perception of sinusoidal lateral vibration, examining the effect of vibration frequency (8 to 315 Hz for the hand and foot; 2 to 315 Hz for the seat) and the effect of input location (the hand, the seat and the foot). Methods Three groups of twelve males aged between 20 and 29 years participated in the experiment. Subjects in each group attended an experiment to determine perception thresholds for lateral vibration via either a rigid handlebar (30 mm diameter) at the left hand (left hand), or a rigid contoured seat (250 mm x 150 mm), or a footrest at the left foot (30.5 mm x 10.5 mm with 10-degree inclination). For the non-exposed hand (right hand) or foot (right foot), a stationary handle and footrest with the same dimensions as the vibrating handle and footrest were provided so that the same body posture was adopted among the three groups of subjects. An up-down (staircase) algorithm was employed to determine thresholds in conjunction with a three-down one-up rule. A single test stimulus (2.0 seconds) was presented with a cue light illuminated during this period. The task of the subjects was to indicate whether they perceived the vibration stimulus or not. The threshold was calculated from the mean of the last two peaks and the last two troughs, omitting the first two reversals. Results The median absolute thresholds of the 12 subjects determined at each frequency for the hand, seat and foot are shown in Figure 1. A frequency dependence of the threshold contours within the investigated frequency range is evident, with similar shape to the threshold contours

Jan 6, 2006

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By William L. Rice

This Bureau of Mines Open File Report on nickel is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign nickel properties and deposits has been abstracted for use in this report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 1984

By N. A. Pace

This is one of a series of papers being published by the Federal Bureau of Mines for the dissemination of information on methods and practices used in the mining and preparation of crushed stone for market requirements. Performance in terms of units of work or tons produced per machine and per operator man-hour are given whenever that information is available. Direct operating costs are useful for comparing different methods, and are, therefore, included if possible. In addition to the factual description of equipment and methods used, it is desirable to discuss the engineering reasons for the choices that have been made. This paper is particularly concerned with the opertions at the Columbia plant of Palmetto Quarries Co. of Columbia, S.C. The plant is about one-half mile east of the Congaree River and adjacent to the southwest corner of the city of Columbia. Rail access is by the Atlantic Coast Line Railroad, and by a spur strack of the Seaboard Airline Railroad.

Jan 1, 1962

By Jr. Sayre

Results of studies of reservoir and wax-precipitation temperatures relating to wax deposition in the reservoir of the Bradford oil field are presented in this report. During 1949 and 1950 Bureau of Mines engineers made temperature measurements in 42 wells, which indicate that the Bradford Third-sand temperatures range from 59.7° F., at 1,150 feet, to 71.9° F., at 2,040 feet. Reservoir temperatures measured at the same depths in newly drilled wells and oil-producing wells differed as much as 4.5u F. Injection-well temperatures measured during water injection showed that the temperature of the water entering the sand was 11.5° F. lower than reservoir temperatures before injection. The cooling in the formation resulting froth the injection of low-temperature water was 11.5° F. in the vicinity of the injection-well bore, and a maximum of 2.1° F. 200 feet from the injection well. Sand temperature, after 5 months of water injection, was reduced 1.5° F. 90 feet from water-injection wells. The temperature at which wax begins to precipitate from solution in crude oil was determined at atmospheric pressure for 26 samples and ranged from 51° to 67° F. Oil samples from wells producing no water had wax-precipitation temperatures ranging from 51° to 58° F. and wax contents from 2.20 to 2.97 weight percent, whereas the samples from wells producing water and oil had wax precipitation temperatures ranging from 580 to 67° F. and wax contents from 2.57 to 3.42 weight percent .

Jan 1, 1952

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air-blast levels and measurement methods are equivalent in terms of structure response, and anyone could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must he used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to preclude damage to residential structures and any possible human injury over the long term.

Jan 1, 1980

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993

By K. L. Paciorek

The aim of the present study is to determine on a gram per gram basis the toxic products of the thermal oxidative degradations of selected compositions. Four families of materials were investigated under the subject contract namely polyvinyl chloride and neoprene compositions, rigid urethane foams I and woods. Three methods were employed to conduct the thermal oxidative degradations: a sealed system (quiescent environment) I a stagnation burner arrangement (dynamic environment) I and a flow-through apparatus (dynamic I but less severe than stagnation burner conditions). The majority of tests were conducted using the first two systems; only limited experiments were carried out employing the third decomposition procedure. All decomposition was done at temperatures of 370 -4000C I the higher temperature being used in the stagnation burner. It has to be stressed that the nature of the products and the relative product concentration are temperature dependent. Thermogravimetric and differential thermal analyses were performed to supplement and extend the above delineated studies and to explore the feasibility of using these analyses as a method for material differentiation.

Jan 1, 1973

By Ivette E. Torres

Aruba, formerly a. part of the Netherlands Antilles, separated on January I, 1986, and became an autonomous part of the Netherlands. Full independence of the island from the Netherlands is scheduled for 1996. In this chapter, however, Aruba's statistics are included with those of the Netherlands Antilles. Tourism continued to be the main industry of the island, which continued to depend heavily on imports, mostly from the United States. During the year, the Government was preparing legislation to regulate the exploration of oil deposits in the relatively shallow sea around Aruba.

Jan 1, 1989

By Donna L. Anderson

This information circular documents the status of a laser-based guidance system to track and control the tramming maneuvers of a continuous mining machine. The work is part of a multiple project effort at the U.S. Bureau of Mines to develop technology for computer-assisted mining systems. The system includes stationary offboard laser-scanning sensors that report the angular coordinates of retroreflective targets on the mining machine. A microcomputer system processes the angular coordinates, determines position and heading, handles requests for data, and controls tram maneuvers of a continuous mining machine. This report describes the hardware for the sensor and computer systems and the software algorithms for continuous miner position and heading determination, closed-loop tramming, and data request handling. Improvements made to the system since previous documentation include the rewriting of the software on a stand-alone real-time microcomputer system, the implementation of real-time programming techniques, the use of a new version of the laser sensor, and the design and development of explosion-proof enclosures for the lasers and corresponding power supply.

Jan 1, 1991

By Warren M. Mahan

A rotary kiln process was developed by the Federal Bureau of Mines to produce consistently an iron product containing 3 to 7 percent nickel. Cuban laterite and serpentine ores were smelted in a gas-fired batch-rotary kiln) 5 feet in diameter and 9 feet long. The metal contained 2 to 4 percent carbon, with little or no silicon, and could be produced on a large scale with modest capital investment. A total of 121 tests was run using this procedure. The tests were conducted with a maximum temperature of 2,625° F., using linings of firebrick containing 40 to 70 percent alumina. Slags in the kiln were acid to neutral. The material in each batch passed through three stages: (1) Sponge metal, (2) carburization, and (3) balling and meltdown. Half the tests were made while firing the kiln with atmospheric-temperature air; the remainder were fired with preheated air. Tests showed that preheated air decreased fuel requirements, dust losses, and reducing agent, and increased the capacity of the kiln.

Jan 1, 1960

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

By J. J. Forbes

Investigations by the Bureau of Mines and by mining-research departments of European countries have established definitely the value of rock-dusting to prevent or limit the propagation of coal-mine explosions. Its effectiveness in this connection has been demonstrated not only by research but by actual coal-mine explosions in which hundreds of lives have been saved because of its presence. In a general way this paper gives pertinent facts concerning rock-dusting practices in the United States. Information has been obtained from many reliable sources, and various coal-mining companies have furnished data on cost and other details.

Jan 1, 1939

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

In 2001, 14,623 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). This was an increase of 210 mining operations compared to 2000. Almost half (49%) were sand and gravel mines, followed by stone (29%), coal (15%), nonmetal mines (5%), and metal mines (2%).

May 1, 2003