Search Documents

By D. R. Flinn

A newly developed chemical conditioning technique, which greatly simplifies the preparation of plating baths for the electrodeposition of titanium diboride (TiB2) coatings, is described in this report. The new plating technique was used to prepare samples of titanium diboride (TiB2) coatings on three types of substrate materials. These samples were then evaluated in both low- and high-speed wear-test programs to determine the wear resistance, microhardness, and adhesion of the coatings. In general, it was found that the wear resistance of the coatings is independent of substrate. Scanning electron micrographs have shown that the coating wear surfaces are very smooth, suggesting slow and continuous removal of the coating during the wear test (that is, adhesive wear). Adhesion between the coating and all substrates was excellent. Microhardness results show that the TiB2 coating is harder than alumina, with a hardness value exceeding 5,000 kg/mm2 measured in one test. The results of the wear tests show that TiB2 coatings have relatively poor wear resistance compared with alumina in low-speed unlubricated sliding environments, but exhibit wear properties comparable with alumina in high-speed unlubricated sliding environments.

Jan 1, 1981

By W. L. Cornell

The Missouri lead ores are the only domestic sources of cobalt presently being mined and processed for other materials. They represent the best short-term solution for meeting up to 13 pct of the Nation's strategic and critical cobalt needs from domestic sources. Presently, the cobalt is lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minium impact on present production does not exist. This paper presents results of research, built upon earlier Bureau of Mines laboratory research, to enumerate the problems encountered in cobalt recovery from the copper concentrate under actual mill conditions; to present alternative solutions to these problems; and finally, to describe the best available technology for cobalt recovery within the imposed constraints. Mineralogical analyses showed the cobalt present as a distinct mineral phase, predominately siegenite, amenable to a physical separation method such as froth flotation. Flotation was chosen for recovery because of easy adaptation by the mills. Unit processes of grinding, conditioning, and flotation were studied individually and in concert, and a series of continuous tests were run based on the parameters developed to obtain engineering data for subsequent economic analysis. Overall cobalt grades of 3.00 wt pct at a recovery of 64.0 pct were achieved.

Jan 1, 1987

By John R. McWilliams

This is one of a series of reports being published by the Bureau of Mines on mining methods and costs at various mines throughout the United States. Including the Holden mine in this series is particularly appropriate at this time. The mine was operated on a low-cost, large-scale production basis to compensate for low-grade ore. Even with the best conditions and the most efficient methods, the margin of profit was small. Under the present situation of rising costs and lowering metal prices, the profit margin vanished. On June 28, 1957, the mine operations ceased; therefore, this report can review the entire life span of the mine.

Jan 1, 1958

By Richard S. Fowkes

Advanced technology, including automation and computerized information systems, is being adopted in mining at an ever-increasing rate to improve safety and productivity and to decrease overall costs. This U.S. Bureau of Mines report focuses on the human factors issues related to advanced technology. Among the significant facts discovered were the following: Experts studying tile design adoption, and implementation of new technology have stated repeatedly that human factors specialists should be involved from the early planning stages, through design and fabrication, and up to and during production, since human factors has been consistently identified as the biggest obstacle to the efficient utilization of new technology. Also, middle management is generally the greatest obstacle to the adoption of advanced technology, this technology can give rise to worker alienation, boredom, stress, job insecurity, and a sense of isolation; training most of the present work force is more cost effective than hiring new workers; workers are willing to accept new technology if they are given a voice in its implementation; the social and the technical systems should be jointly optimized; and with the intro¬duction of advanced technology, the cognitive or mental, rather than the physical, aspects of human-machine interaction must be emphasized.

Jan 1, 1994

By Frank B. Fulkerson

This is the second of two interrelated studies of waterborne transportation. The first study discussed transportation of mineral commodities on the inland waterways of the South-Central States.2 Together, the two surveys describe and analyze the flow of foreign and inland waterborne commerce of the gulf coast. All the principal mineral-industry imports and exports of the gulf coast are mentioned in the report, including metals, nonmetals, and mineral fuel products, The gulf coast foreign trade in mineral industry products was determined to be composed of a small number of commodities.

Jan 1, 1971

By N. Kumar Kittusamy

A field study was conducted to evaluate seat designs on shuttle cars. Eight operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers also measured the levels of vehicle jarring/jolting. Four basic seat designs were compared on low and mid-coal seam shuttle cars during production operations at two underground coal mines. Two seats were currently used on the shuttle cars and another two were NIOSH designs. Objective data were collected using accelerometers with pre-amplifiers and filters connected to a data recorder; whereas subjective data were gathered with a visual analog scale (VAS) and a questionnaire. Results from measured levels of jarring/jolting showed that the NIOSH Seat L2A smoothed out bumps better than any other seats. Using the VAS, mid-seam and low-seam shuttle car operators rated the levels of jarring/jolting and discomfort lower with the NIOSH seat than the other seats. Questionnaire responses indicated that operators rated NIOSH seat designs as more comfortable. This research will provide the industry with better seat designs for isolating jarring/jolting in vehicles. Furthermore, researchers plan to improve the NIOSH seats using information gathered in this study.

Jan 1, 2003

By E. D. Gardner

Open-cut mining of copper ores in the western United States is a relatively new industry. At first the mining methods were mainly adapted from those used at open-cut iron mines and at quarries, but now efficient practices that are more suitable for the copper deposits have been developed. The pioneer in this field is the Utah Copper Co., of Bingham, Utah, which deserves great credit for working out much of the early procedure. Stripping began at that mine in 1906, and the large Garfield concentrator was put in commission in 1908. Next in order of development were the Nevada Consolidated Copper Co., at Ely, Nev. ; the Chino mine of the Ray Consolidated Copper Co., at Santa Rita, N. Mex. ; the New Cornelia Copper Co., at Ajo, Ariz. ; the Sacramento Hill mine of the Copper Queen Branch, Phelps Dodge Corporation, at Bisbee, Ariz.; and the open cut of the United Verde Copper Co., at Jerome, Ariz. The Sacramento Hill mine began to produce in 1923, and the United Verde open-cut mine has produced ore mainly in connection with stripping. The writer visited the Utah Copper mine in September, 1923; the Nevada Consolidated in August, 1923; the Chino in July, 1924; and the New Cornelia, the Sacramento Hill, and the United Verde open cut at various times during 1922, 1923, 1924, and 1925, mostly in connection with other work.

Jan 1, 1927

By M. R. Geer

Information on the performance of coal-cleaning equipment is necessary to provide a basis for evaluating the performance of existing plants and projecting that of new plants. Performance data can contribute greatly to the wise selection and effective use of coal-washing equipment. The Bureau of Mines has published information on the performance of several commercial plants, as well as of some laboratory-scale equipment, 5 (2-9, 11, 12, 17-12, 21-25) from time to time for a number of years. A more intensive program to provide such information for all the principal types of cleaning equipment is underway. The present evaluation of table performance is part of this program.

Jan 1, 1962

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 313, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and. January and March, 1932, as published in Reports of Investigations 3l40, 3147, 3l50, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active permissible list: [Austin Red Diamond No. 1, L. F. Gel-Coalite W. L. F. Austin Red-Diamond No. 5, L., F. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No. 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.]

Jan 1, 1932

By L. B. Berger

The Haldane gas-analysis apparatus used by the Bureau of Mines is patterned after the device developed by Haldane 4/ and differs from it only in structural modifications that have been added to facilitate operation and simplify construction. The apparatus was developed to permit determination of carbon dioxide, combustible gases, and oxygen with a degree of accuracy not attainable with apparatus of the types ordinarily used for the analysis of fuel gases, flue gases, and similar mixtures. The Haldane apparatus is used by the Bureau of Mines chiefly in the analysis of air samples collected in coal and metal mines and other underground workings and is applied also in the analysis of many other types of gas mixtures when accurate determination of certain constituents is desired.

Jan 1, 1938

By E. P. Ferrero

Crude oils from fields throughout the world are analyzed by the Bureau of Mines to determine the characteristics of the oils and their contribution to the petroleum resources of the world. Analyses are reported for 169 foreign crude oil samples from 122 oilfields in Africa, Asia, Australia, the Caribbean, Europe, North America, and South America. Tables show the geographic and geo- logic origin of the samples, names of companies that supplied the samples, annual production for the fields, general characteristics and analytical and computed data, hydrocarbon-type data, cumulative production of the larger fields, and references to sources of geological and field development information. The analyses were made by the Bureau of Mines routine method and comparisons may be made with more than 8,000 other such analyses.

Jan 1, 1972

By Mary Cocklan-Vendl

Regulatory processes associated with development of a world class lead-zinc mine, Red Dog Mine, in northwestern Alaska were reviewed and evaluated. Informal interviews with key project personnel, consultants, and agency field and permitting specialists provided perspective on the regulatory successes and failures of the project. Due to potential impacts to air quality, water quality, wetlands, and National Park lands, an Environmental Impact Statement was required. By developing a comprehensive baseline of information on the existing environment to aid in minimizing impacts during project siting/design and through regular coordination of evolving project plans with regulatory agencies, the mine developers were able to acquire necessary permits in a timely and cost effective manner. The only major exceptions occurred when inadequate information was collected on dispersal of airborne particulates, rates of surface water run-off, and groundwater quality. These deficiencies resulted in the need for design changes, unscheduled construction, additional environmental monitoring costs, and delays in issuance of the NPDES permit.

Jan 1, 1992

By S. J. Page, R. A. Jankowski, J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 1992

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By Martyn F. Roetter

The objectives of the work described in this report are to determine the communications requirements and need for communications, both for voice and control, on longwalls, and to make recommendations for longwall communications equipment and systems. These recommendations are designed to guide the future development of longwall communications. Information necessary for the accomplishment of this work has been gathered by a series of visits to longwall mines and discussions with longwall mine operators, as well as with suppliers of longwall communications and mining equipment and with Bureau of Mines personnel. In addition, it has proven possible, through personal interviews and literature evaluation, to gain an understanding of the experience and attitudes towards longwall communications in countries where longwall mining is far more widespread than in the U.S., namely the Federal Republic of Germany, the United Kingdom, France and Belgium.

Jan 1, 1976

By J. R. Nettle

The purpose of these studies by the Federal Bureau of Mines was to determine the feasibility of refining low-grade hafnium by an inert-gas-shielded molten-salt electrorefining technique to produce a hafnium metal meeting reactor specifications. The techniques were adapted from those used success-fully for titanium electrorefining. Three electrolytes containing hafnium chlorides were developed from which deposits having a Brinell hardness of 170 or below were recovered. A KC1 + NaC1 + HfC14 electrolyte produced deposits in the hardness range of 140 to 165 Brinell. Deposits with a hardness range of from 132 to 152 Brinell were pro-duced from an electrolyte composed of KC1 + LiC1 + HfC14. A third electrolyte composed of NaC1 + K3HfC17 produced deposits with a hardness as low as 139 Brinell. In a fourth electrolyte, composed of NaC1 + K2HfF6, a measure of refining was accomplished, but under the test conditions no metal meeting specifications was recovered; none was softer than 174 Brinell. A number of metallic impurities were reduced in quantity by the electro-refining process, notably iron, which normally was reduced from 250 p.p.m. to less than 50 p.p.m. Magnesium generally was reduced from 680 p.p.m. to less than 80 p.p.m. Manganese content was also reduced by the electrorefining process. Sponge containing 90 p.p.m. Mn yielded deposits containing a maximum of 50 p.p.m.; some deposits contained only 10 p.p.m.

Jan 1, 1961

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By C. B. Kenahan

The Bureau of Mines is developing methods for reclaiming the metal and mineral values contained in municipal incinerator residues. This report describes the first phase of the research, in which reliable methods for sampling and analyzing municipal residues were established and the composition and characteristics of the residues were determined. Samples were obtained from a variety of grate-type furnaces and also from a rotary kiln furnace. The samples were processed on a batch basis and separated into their natural categories by a variety of methods including screening, magnetic separation, air separation techniques, and handpicking. The main components of the residues were determined to be metal and metal oxides, glass, and ash.

Jan 1, 1968

By Noel N. Moebs

Valley Camp No. 3 mine was the scene of an experimental shortwall introduced in 1973 in an attempt to improve the recovery from the Pittsburgh coalbed in the Ohio Valley area where adverse ground conditions have imposed partial extraction methods with only 40 to 55 percent recovery of the valuable resource. The Bureau of Mines, under a cooperative agreement with Valley Camp Coal Co., monitored ground pressures and caving in the shortwall section in an effort to determine whether the roof strata, notably the limestone main roof, will cave to the extent that roof pressures at the face are relieved and whether the powered roof supports can sustain the roof load. The Bureau's efforts included mapping of clay veins, instrumentation of chain pillars and shortwall panels with encapsulated pressure cells, recording hydraulic pressures in the legs of the shortwall chocks, and core drilling underground and from the :surface. The experimental shortwall was a qualified success. Recovery increased 5.4 percent compared with partial extraction. Pressures in chain pillars and the abutment zone were not excessive. Hydraulic pressures in the chock legs did not approach the yielding pressure. Apparently, the limestone strata caved and the roof pressure at the face was relieved.

Jan 1, 1976