Search Documents

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

By R. S. Dean

In addition to the normal work and that pertaining to strategic minerals, the Metallurgical Division has been made responsible for carrying on major investigations in the development of processes' for the treatment of low-grade domestic manganese ores that heretofore have failed to yield products suitable for the preparation of ferromanganese, an alloy essential to every ton of steel produced. These investigations are particularly important at this time because of their part in tucking this country self-sufficient with regard to manganese when the stock-piled ore becomes e exhausted and as foreign shipments of ferro-grade ore are cut off. The results indicate that there is a good probability of accomplishing this objective, while at the same time conservation may be promoted through the use of normally useless material from the large, low-grade ore deposits.

Jan 1, 1941

By Wilton Johnson

Native asphalt was produced by three companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm, R. L. White Co., Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Colorado and Utah, was mined by two firms, American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), and Ziegler Chemical and Mineral Corp. Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) closed its mining operation during the year.

Jan 1, 1988

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959

By CHARLES L. WRIGHT

Coals may be divided into six classes-anthracite, semi anthracite, semibituminous, bituminous, subbituminous, and lignite. The first three cla~ can be distinguished by dHferences of composition, particularly the proportions of fixed carbon and the ratios of the fixed carbon to the volatile matter in the cools. The last three classes can be distinguished by di:fferences in physical character, chiefly in color and in manner of weathering. Lignite is brown, not black, and has generally a woody look, but it weathers in much the same way as subbituminous coals. On exposure to the air lignite slacks or crumbles. The lumps check and fall into small irregular pieces that exhibit a decided tendency to separate into extremely thin plates. Hence lignite deteriorates greatly during storage or long transportation. The most characteristic feature of the composition of lignite is a large percentage of moisture. '!his high moisture content reduces the fuel value of freshly mined lignite, and the partial evaporation of moisture, on expooure, causes th6 fuel to check and fall to pieces. Consequently, attempts to increase the efficiency of lignite as a fuel involve reducing its percentage of moisture and increasing its ability to endure storage and transportation. Both these results are accomplished by briquetting.

Jan 1, 1911

By Melford H. Salsbury

The maximum net return from the sale of ores and concentrates of gold, silver, copper, lead, and zinc accrues to the producer when these mine products are marketed to the best advantage. Data are presented that the producer, especially the small mine operator, can use to survey available markets and make a preliminary estimate of the net return to be expected from an ore, on the basis of typical mill, smelter, and freight schedules. A review of the industry is presented by States in which recent production statistics are given, marketing facilities are discussed, and locations of principal mining districts, custom mills, and smelters are shown. Explanations of treatment processes, ore types, treatment charges, payments for metals, and deductions are given. Published rail and truck freight rates for mine products, based on marketing patterns developed over many years, are listed and explained.

Jan 1, 1964

By L. C. Brichta

The Canyon Diggings zinc-lead deposit is in an area of structural deformation of sedimentary rooks in Newton County, Mo., 14 miles southeast of Joplin, within the southern limits of the Tri-State district. Mining and milling on the several tracts covering the area had been carried on sporadically since 1900, and incomplete records show a production of 1,341 tonsof zinc and lead concentrates. On the northern part of the deposit the predominant metal is which occurs as galena, cerrusite, and pyromorphite in broken chert near the surface. On the southern part, lead is subordinate to zinc, which occurs mainly as carbonate and silicate minerals in brecciated chert to a maximum depth of about 150 feet. Analyses of samples from Bureau of Mines drilling indicate that approximately 77 percent of the zinc and 50 percent of trio lead i8 in nonsulfide minerals resulting from the oxidation of sphalerite and galena. Between August 12, 1948, and October 5, 1949, the Bureau of Mines investigated the deposit by churn drilling and sampling 85 holes aggregating 10,571 feet of bore and sampling two mill-tailings dumps and three mine dumps. Factual data on the investigation and the logs of Bureau of Mines drill holes are presented in this report.

Jan 1, 1950

By H. R. Beard

The Federal Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environ¬mental conflicts, impacts, and occupational hazards Associated with mining and mineral processing operations. Tailings and soil samples from Wyoming and Utah were contacted with tailings liquors to determine the degree of absorp¬tion. Absorption ranged from 0 to 99 percent for radium and from 0 to 31 per¬cent for thorium. Some samples, which readily absorbed radium, were contacted with various salt solutions that could be present in tailings solutions to determine their effectiveness as desorbents. The desorption of radium ranged from 0.06 to 100 percent. An alpha-spectrometric method was used to determine the radium and thorium, concentrations in the solutions and the solids.

Jan 1, 1979

Presented in this volume are the basic mining techniques and production operations associated with underground bituminous coal mining. Chapter 2, "Multiflow Process Charts", presents, in sketch form, a description of the various operations characteristic of conventional and continuous mining. In order to focus attention upon the major components and operations in each work cycle, certain items are not shown in the sketches, e. g., machine electrical cables, brattice, and rib posts. The elapsed time shown for each sketch is considered representative for the various work elements summarized by the sketch. More detailed work element times can be found in Chapter 3, "Typical Work Cycle Times", and Chapter 4. "Standard Time Data".

Jan 1, 1971

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the CaF2-Y203 system for which solidus and liquidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. All specimen compositions were blended from high-purity materials and encapsulated in Mo or Pt20Rh prior toheat treatment. Liquidus temperatures were determined by ceramographic examination of heat-treated and quenched specimens. Solidus temperatures were determined by differential thermal analysis and by electron microprobe analysis of quenched specimens. Terminal solid solubilities were derived by parametric methods. The peritectic system was found to be pseudobinary due to the formation of yttrium oxyfluoride at temperatures near the liquidus. The peritectic point occurs at 7 mole pct Y203 and 1,438° ± 5°C. The terminal solid solubility of Y203 in CaF2 decreases from 7 mole pct at 1,438° C to 1 mole pct at 1,100° C, and the solubility of CaF2 in Y203 decreases from 9.5 to 7 mole pct over the same temperature interval.

Jan 1, 1970

By John D. Sullivan, Alfred P. Towne

"In copper percolation-leaching plants the ore is usually crushed to a maximum size of about three-eighths inch. Ordinarily an ore is crushed as finely as feasible since the rate of extraction of copper is increased with decreasing size of particles owing to the greater surface exposed and. the shorter path required for solutions to come into contact with the minerals to be dissolved. However, greater degree of crushing also increases the amount of fines. When ores are charged into leaching vats the coarse and fine material tend to segregate, resulting in channeling of solutions and leaving the areas where fines predominate only partly leached. An improvement in the method of charging the ore into vats that would minimize the deleterious effects of the segregations of fines would increase the percentage extraction of copper.The Inspiration Consolidated Copper Co.4 recently installed classifiers to remove the primary slimes from the ore, before charging it into the leaching vats. This necessitates a separate agitation treatment for the slimes.Recent publications5 of the bureau have shown the advantages of agglomeration followed by trickle leaching to extract copper from concentrator tailings. It was shown that when equal parts of ore crushed to about 1/4-inch size and concentrator tailings were agglomerated with approximately 10 per cent of moisture, either in the form of water or leaching solution, and the mass was charred into a leaching vat the ore could be treated successfully by open-drainage trickle leaching. Even with 30 or 35 per cent of minus 200-mesh material present the ore could be leached, if it was not flooded with solution.The results obtained in agglomerating ores and slimes suggested the possible advantages to be gained by wetting the crushed ore for standard percolation-leaching plants before charging it into the vats. Wetting the ore whould make the fine material and slime cohere to the larger pieces of ore thus tend to prevent segregation when the ore is charged into the vats. The bureau, at its southwest Experiment Station and in cooperation with the Department of Mining and University of Arizona, Tucson Ariz., therefore made a study to work: out A way in which slimes could be handled in percolation leaching. The study showed that the method of charging ore into the leaching vats governed the distribution the fines and consequently the rate extraction of copper. The results of the study reported in this paper."

Feb 1, 1931

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr2O3. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 16 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, stope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider stopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor's response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor's head prevented catalyst poisoning efficiently.

Jan 1, 1981

By R. F. Droullard

The Bureau of Mines has used gross alpha and gross beta detectors to continuously measure radiation working levels for a number of years. During this time, improvements have been made in the design and performance of continuous working-level (CWL) detectors. This report discusses the improved designs and some of the operating principles and applications of CWL detectors in the measurement of radon daughter products in mines and dwellings.

Jan 1, 1985

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By Verne E. Hooker

Stress-relief techniques and instrumentation have been developed through many years of research in the Federal Bureau of Mines and successfully used to determine the in situ state of stress in rock. This paper describes the drilling equipment and accessories for use with the Federal Bureau of Mines three-component deformation borehole gage. Operation and calibration procedures for the deformation gage are discussed in detail. Site selection and overcoring procedures are included to provide a complete working knowledge for surface or underground applications.

Jan 1, 1974

By Alice Turcot

Knowledge of risks from exposure to hand-arm vibrations is usually presented by clinicians and researchers from a medical and engineering point of view. There is a strong need to develop innovative health promotion programs for exposed workers. Risk perceptions by vibration exposed workers and HAVS (hand-arm vibration syndrome) affected workers are less well known. In 1983, Brubaker demonstrated that 75% of studied fellers thought that whitening of the fingers was part of the job and/or an unrelated nuisance, while only 25% believed it was a disease. 1Grounds also showed that even though there were a very high number of forestry workers with white fingers, none considered quitting because of their condition. 2 It seems that many workers hesitate to declare the illness or believe they are less affected than they really are, perhaps from fear of losing their jobs and livelihood. 3 Risk awareness, on the part of exposed workers and their employers, as well as knowledge and acceptance of available preventive solutions are necessary steps before installing adequate preventive measures, whether organizational, behavioral or environmental. Workers need to understand fully the hazards and risks in order to be able to make informed decisions under uncertain conditions.4 Prerequisites include the following: workers knowledge about the risk, their attitude towards it, which in turn, can be influenced by values, needs and interests. Also, knowledge and attitudes towards safety behaviour, organizational or environmental barriers must be taken into account. Our research focuses on these key elements, which help bridge the gap between health promotion research and practice. Methods A descriptive exploratory study is in progress with workers exposed to hand-arm vibrations. It uses qualitative methods that include focus group discussions with workers exposed to hand-arm vibrations, as well as individual interviews with other key informants (employers, health care professionals). An open-ended questionnaire was developed to collect qualitative data on perceived risks and solutions to prevent or reduce HAVS. Based on an integrated theoretical framework related to known determinants of behavior change, the analysis will focus on the following5: 1) knowledge of health effects, safety, well-being and/or quality of life 2) related beliefs about individual susceptibility and severity of consequences 3) attitude and values related to hand-arm vibration exposure 4) knowledge and attitudes towards exposure reduction, as well as perceptions of barriers and facilitating factors for these measures, in the workplace environment or otherwise.

Jan 6, 2006

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.