Search Documents

By Eric Grigoryan, Wade Hutchison

An engineering study of 2,250 blasting damage claims from 1999 to 2008 in Tennessee, Kentucky, Virginia, Nevada, California, Georgia, South Carolina, North Carolina, Alabama, Arizona and Utah were investigated over the last decade and these investigations determine that blasting ground vibrations damage claims are valid less than 1.3 percent of the time. This study determined that valid blasting damage occurred as a result of impact damage associated with fly rock, air concussion stressing, instantaneous reverse stressing associated with ground vibration and crater zone soil shifting related stressing.

Jan 1, 2009

By Curtis Garner

Griesemer Stone located in Springfield, Missouri has supplied aggregate in Southwest Missouri since 1946. In 1954 the decision was made to mine the formation and utilize the mined out area for warehouse space. As advancement proceeded, entrances and small diameter air shafts for ventilation were needed and had to be added. It was decided in 1989 to sink an 8' diameter air shaft designed to move 200,000 cubic feet of air per minute with the help of (4) four 50,000 CFM Loren Cook Fans.

Jan 1, 1991

By Michael Weaver, Dale L. Ramsey

The Pinkerton Tunnel open cut project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 21 feet of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between mid-Atlantic states and their ports to midwest markets in the U.S. This project involved drilling and blasting of 1.2 million bank cubic yards of rock over a 14 month period while maintaining rail traffic of two passenger and 38 freight trains daily. See story and photos, page 6.

Jan 1, 2015

By Michael S. Wieland

This report discusses the U.S. Bureau of Mines research regarding the desensitization and malfunction of cap-sensitive explosives deployed in underground coal mines. Delay blasting in underground coal generates severe shock waves and rifting forces that fracture and heave coal. These dynamic interactions can damage other charges still remaining in the delay pattern. The debilitating impacts precipitate degrees of reduced charge performance ranging from misfires to weak detonations or out-of-sequence firings. Damaged charges react poorly, perform less useful work, and/or generate atypical fumes with higher toxicity.

Jan 1, 1993

By Mark S. Stagg, Stephen A. Rholl

The U.S. Bureau of Mines has developed computer software which uses fast Fourier transform (FFT) techniques to evaluate blasting data. The software is useful because it allows blasters to evaluate 1) the frequency content of ground vibration time history data; 2) the effects of initiator scatter on the frequency spectra of ground vibrations; and 3) the fragmentation distribution of rock muckpiles from photographs. A one-dimensional version of the software was used in the first two cases. Monte Carlo techniques were used to simulate the scatter of initiators.

Jan 1, 1995

By Gregg R. Gitschlag

There are more than 4,000 oil and gas structures present in the U. S. Gulf of Mexico. Approximately 100 structure removals occur each year and 66% of these are removed with explosives. From 1993-1995 an intensive study was conducted on the fish kill resulting from the explosive removal of 6 platforms off the Louisiana coast in water depths from 14-28 m (45-92 ft). After explosives were detonated, all floating fish and a sample of the dead fish which sank to the sea floor were collected.

Jan 1, 1997

By Stafan Rose, Art Madsen

Four years ago, Peabody’s North Antelope Rochelle Mine (NARM) site started experimenting withANFO and Liners in its Cast Blasting operations. The motivation to use ANFO was based on the following:1. ANFO generates more gas thereby resulting in greater heave/movement. 2. ANFO is a more consistent product because there are less components/ingredients. 3. ANFO when protected from water contamination does not produce NOx smoke.

Jan 1, 2007

By R Malo, A Yetter

The use of large diameter blastholes for underground mining began approximately twelve years ago and are now routinely employed in a variety of ore types and stope designs. These large boreholes, ranging in size from 4 1/2 inch to 8 inch diameter, were first utilized in the same fashion as in open pit bench drilling. However, a variety of changes quickly followed in order to accommodate the unique conditions encountered while using a blasthole sloping method.

Jan 1, 1984

By Ulrich Leiste

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Norman S. Smith, Richard L. Ash

Many factors affect rock fragmentation from blasting. One variable seldom considered when designing blasts, however, is the borehole length. An example is described of how the length was adjusted to give better breakage when using 4-inch diameter blastholes at a quarry. To explain the basic principles involved test results from experiments conducted by the authors where borehole lengths were altered are presented and evaluated.

Jan 1, 1976

By James Stuart

A man died when the primed charge he was holding against his chest exploded. He was doing legitimate explosive work, and he was following all the safety procedures he had been taught. He and his colleagues had done this, thousands of times previously, with no ill effects.

Jan 1, 2007

By Kevin Dunfield

The Deltadet System is composed of: The Deltadet II electronic Detonator. A Field Terminal to create, modify or simply execute an existing blasting sequence. The radio remote controlled option is composed of a Base Station to program, calibrate and initiate the EDDs plus a Blasting Box to send commands to the Base Station. Blasting lines to connect the EDDs to the Base Station (100m) and Visual Blast software to create or modify a blasting sequence.

Jan 1, 2004

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By Ayman Tawadrous, Hendrik Botha, Simon St J Tose

The early miners and their mules always had the challenge of transporting unstable dynamite underground. The modern pumpable explosives, whilst far safer, still present a major logistics challenge for the mobile charging units (MCU). The challenge today is the efficient explosive delivery into declines, ramps, and vertical shafts, often requiring the MCUs to travel excess distances up and down to surface to re-load. Alternatively, the management of cassettes or ISO containers is utilized to deliver the pumpable base emulsion to the MCUs at the working face. Additionally, local laws and regulations regarding shaft clearance further compound the task and result in pausing other operations in the shaft or decline or ramp until the completion of the explosive transport. This paper examines the research & development challenges of dropping base emulsion down a vertical pipe to depths in excess of 1000 m (3280 ft.), either to an underground storage or directly into the MCU, depending on the depth. The boreholes (with pipes) are drilled in close proximity to the underground work areas. The paper also discusses the rheology of the emulsion within these vertical pipes as well as the economic benefits of such an innovative system. The learnings gained from this work, along with examples demonstrating the significant reduction in MCU travel and the safety benefits, are presented for the industry to consider moving forward.

Jan 21, 2025

By Cameron McKenzie, John Heilig, Patrick Andrieux, Andree Drolet

It is widely accepted that both underground and surface blasting operations can de-stabilise excavations to the point where it can threaten the feasibility of mining through personnel safety or OK dilution. Research has been undertaken to outline a practical method in which the impact of blasting will be accounted for during the early excavation design stage by modelling, and during the following production stages by monitoring rock response to blasting operations.

Jan 1, 1994

By Yonghun Jong, Chungin Lee

The main purpose of this study was to apply the artificial neural network (ANN) models to determine optimal powder factors and predict peak particle velocities, based on a series of observations and input parameters. The used blasthole pattern was V-cut. The locations of blastholes and ignition patterns remained almost constant. The input parameters were 14 geological conditions (i.e., dip, dip direction, spacing, separation, and persistence of 2 discontinuity sets, tunnel orientation, rock strength, RQD, and RMR) and 4 blasting conditions (i.e., distance between blasting points and measuring points, charge weight per delay, drilling length, and blasting efficiency). Data for the ANN application in this study were recently collected in a highway tunnel under construction in Korea. The main rock type in the site was biotitic granite. An optimum ANN model was determined by training models with collected data. The trained model was used to evaluate the prediction capability of the optimum model. It was shown that the ANN model could predict the powder factor and the peak particle velocity depended upon the selected input parameters. Particularly, the ANN model predicted more accurate peak particle velocities than those obtained by the blasting vibration equation. Moreover, the more dominant factors among the input parameters could be determined by analysis of the relative strength effect.

Jan 1, 2002

By Daniel Haines, Benjamin Konshak, Michelle Crull

American Technologies Incorporated Group (ATI) is the prime contractor with U.S. Army Corps of Engineers, Huntsville Center (CEHNC) in the Honolulu District for the removal of munitions and explosives of concern (MEC) at the Former Waikoloa Maneuver Area. The site is approximately 123,000 acres on the Big Island of Hawaii, which was used as an artillery firing range with live ammunition and other explosives deployed. ATI utilizes state of the art metal detection equipment to find and excavate metallic anomalies that have hazard potential. Both the investigation and disposal procedures present challenges due to residential communities and archeological sites that are located in and around the site. In order to excavate metallic anomalies safely and without adverse impact, ATI utilizes CEHNC-designed, open front barricades constructed of sandwiched sheets of aluminum with a support structure. When munitions or explosives are located, ATI is responsible for safe disposal using shape charge perforators to detonate the item where found. Sandbags are used for mitigating the effects of all detonations.

Jan 1, 2008

By Ian A. Niell, Alastair C. Torrance

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation velocities of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation measurement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 1509. However, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1990

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018

By Rakesh Raghavaraju, Bibhu Mohanty

Prediction of fracture and fragmentation characteristics of a rock mass subjected to dynamic loads, such as in blasting remains a major technical challenge. The present study is aimed at characterizing the shock transmission properties in controlled experiments in small scale in a well-characterized granitic rock, under varying borehole coupling conditions. Single blast-hole tests were conducted in a granitic rock sample of 145 mm (5.7 inches) diameter and height. The boreholes (in two diameters: 6.4 mm (1/4 inch) or 9.5 mm (3/8 inch)) were loaded with detonating cord of varying charge weight (5.3 g/m or 25 grains/ft to 31.8 g/m or 150 grains/ft of PETN). The effect of explosion gas penetration into the target rock was eliminated by inserting a thin-walled copper liner along the borehole wall. Embedded carbon composite resisters were employed at varying distances from the borehole to measure transmitted shock pressure for two coupling conditions (i.e. air and water) at distances of 1x to 9x the borehole diameter. The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.