Search Documents

By O. L. Kachor, A. V. Bogdanov

"In 2015 in the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» Federal State Budget Educational Institution of Higher Education ""Irkutsk National Research Technical University” (further–INRTU) performed works aimed at disposal of accumulated arsenical residues at industrial site of the former Angarsk arsenical plant (AAP) processing arsenious ores from Svirsk town in Irkutsk region. The plant in 1934-1949 produced arsenic trioxide for the defence industry. Prior to starting the works on disposal of industrial pollution focus the total amount of cinders stored on 13 ha of industrial site of AAP was 156 900 tons with 1% average arsenic content. Close to the cinders there were also remains of industrial buildings and process equipment in the amount of 6 600 m3 that contained 150 tons of arsenic. Additional source of pollution at the industrial site of AAP is contaminated soil amounted to 48 000 tons. Proven reserves of gold and silver in the cinders were 6.1 and 47 g/t respectively. In 2015 the source of arsenious pollution was detoxificated according to mineral matrix technology and stored in a special landfill with separate stocking of gold-containing cinder and other arsenious residues. This technology of waste disposal specifies extraction of valuable metals from cinder in future. The similar case is with Vershino-Darasunsky settlement in Trans-Baikal Territory where the abandoned industrial site of the former arsenic plant is located in the central part of the settlement. The concentration of arsenic and valuable components can be compared to the concentration at AAP. Since 2016 the demand for removal of such industrial pollution sources is legislated due to amendments in Federal Law No. 7-FZ on environmental protection. It results in a real possibility to remove such dangerous industrial residues deposits as the one located in Vershino-Darasunsky settlement. INTRODUCTION In the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» as well as the Irkutsk region program “Environment protection in Irkutsk region"" for 2006-2015, INRTU performed the works aiming at disposal of accumulated environmental deprivation–arsenical residues from the former Angarsk arsenic plant (further - AAP) (Figure 1) on processing of arsenopyrite ores of Svirsk town in Irkutsk regionThe plant produced arsenic trioxidein 1934-1949."

Jan 1, 2018

Cenospheres is a sandlike hollow sphere component of the fly ash that is collected in coal-burning electric power generating plants. Metal coated particles have been widely used in industries. Magnetron sputtering method which was used to coat copper film on the surface of the cenospheres is a widely used coating technique in large surface metal coating. A newly designed equipment is used to make the fine particle coating can be carried out because the fine particle is hard to disperse and it must make the particle keep moving to let every direction of the particle be coated. The copper film coated is compact, smooth, even and without uncoated spots under the optical microscopy and SEM. The film has good affinity to the cenosphere surface. The film does not separate with cenoshpere surface even when the cenosphere is crushed. The XRD, SEM, XPS, SPM was used to study the copper film characteristic. It is shown that using this newly designed magnetic sputtering equipment can coat high quality copper nanofilm on the cenoshpere surface.

Jan 1, 2014

By E. Ashirbaeva

"Ores of ferrous metals traditionally make up the bulk of recoverable reserves of solid minerals, and iron ore concentrates - in the processing and consumption. To obtain concentrates, three main methods are used: dry and wet magnetic separation, gravity and flotation. But even their integration into complex developed schemes with finishing operations often do not solve the problem of obtaining high-quality concentrates, which are necessary for powder metallurgy and electric steelmaking. Increasing the iron content in the concentrate by removing harmful impurities is the goal of this work. The possibility of reducing the operations of wet magnetic separation twice and completely eliminating concentrating operations in ball mills from the scheme of operations has been established. Selective leaching agents for each type of iron ores have been created, allowing to obtain concentrates with an iron content of not less than 68-69% and negligible concentrations of harmful impurities. Methodical recommendations for long-term storage of bioreagents in the active state, their immobilization and preparation in industrial conditions at the enterprise Nedropolzovatelja are developed. The proposed biotechnology, which allows to obtain high quality iron and conditional concentrates for harmful impurities, is protected by patents (RU 2537684 ""Method for fine-tuning of high-sulfur magnetite concentrate"" for magnetite ores and Pat. RU 2599068. For the industrial implementation of the new technology, organizational and technological measures have been developed in the system with Road maps for types of ores. The developed technology makes it possible to condition noble metal, tin, tungsten, nickel and other concentrates in harmful impurities such as arsenic, antimony, mercury, sulfur, copper, zinc, iron, phosphorus, manganese, in total 30 components that pass into solution under the influence of bioreagents.INTRODUCTION Consumption of various metals is steadily increasing every year, the volume of mining is constantly increasing. Ores of ferrous metals traditionally make up the bulk of the recoverable reserves of solid minerals. Enrichment technologies for iron-containing ores are reduced to the combination of three main methods: wet and dry magnetic separation, gravity and flotation. But even the use of complex advanced technological schemes often does not lead to the production of high-quality concentrates suitable for metallurgical processing. In this case, either lapping operations or effective technical and technological solutions are used in the main enrichment cycle. Widely used in practice methods for improving the quality of iron ore concentrates include the use of finishing operations (fine screening, reverse cation flotation), staging of concentrates, the use of more sophisticated equipment (separators with running magnetic field, magnetic gravity classifiers, column flotation machines)."

Jan 1, 2018

By Douglas Fuerstenau

"Comminution not only is the major energy cost in mineral processing but it also can limit the grade of ores that can economically be processed. Rittinger first postulated that the energy for comminution is proportional to the new surface produced. Because most of the strain energy needed to initiate and propagate cracks in particles cannot be recovered, researchers reported woefully low comminution efficiencies. Recognizing this, Schoenert proposed that the baseline for assessing comminution efficiency should be the mechanical energy needed to break single particles. After extensive single-particle studies, Schoenert turned to comminuting beds of particle in piston dies. Finding particle-bed comminution to be energy efficient, he had the brilliant conception of making the process continuous, namely his invention of the choke-fed high-pressure roll mill (HPGR). Practical comminution involves masses of particles, which can lead to energy efficiencies far less than that of single-particle breakage. A three-way classification of grinding modes in terms of the mobility of the particle mass provides the necessary insight into the low efficiency of different comminution machines: namely, single-particle breakage, confined particle-bed grinding (HPGR), and loose-bed grinding (ball mill). Examples are given for determining and comparing comminution efficiencies. The size distribution of comminuted products become self-similar, and a single parameter, the median size, can be used to quantify the extent of comminution. The reduction ratio, expressed in terms of the mean size of the feed and product, varies linearly with expended energy and the slope of such plots is a measure of the grindability of the mineral. This approach clearly gives the order of energy efficiency as single-particle > particle-bed > loose-bed comminution. HPGRs are more efficient at low reduction ratios but lose that advantage at higher reduction ratios. Extensive hybrid grinding experiments carried out with our instrumented ball mill and HPGR showed significant energy savings by first comminuting the material in the HPGR and followed by the ball mill. At Cerro Verde an industrial-scale hybrid HPGR/ball mill system is reported to have a 13 percent energy savings over a SAG mill/ball mill system."

Jan 1, 2014

By Scott C. Brown, Brij M. Moudgil, Ivan U. Vakarelski

The manipulation of the apparent hydrophobicity of particlute surfaces is necessary to achieve optimal selectivity in flotation processes. Previously a number of works have investigated the role of microscale surface and particulate morphologies on chemically modified substrates. These works have suggested that microscale surface asperities lead to an increase in flotation efficiency by assisting in the rupture of wetting films. Yet, in mineral processing the presence of surface asperities may lead to a reduction in flotation. The reason for this may-in part-be due to the presence of nanoscale irregularities at the interface. In this work, it is proposed that the presence of roughness at the nanoscale may have a dominant impact on the apparent hydrophobicity of mineral surfaces during flotation. It is suggested that as inter-asperity seperation distances are reduced capillary effects are enhanced for high energy mineral surfaces leading to the formation of liquid domains, which adversely impact hydrophobicity. In addition, as these distances approach the surfactant headgroup size obstruction of surfactant self-assembly process may occur, thereby further limiting flotation.

Jan 1, 2003

By Özcan Y. Gülsoy

Coal beneficiation with optical sorting has not yet been studied in detail. Optical separation of coal from gangue particles as a dry method can be used as an alternative to the other enrichment methods. Developments in optical and pneumatic technology put the optical sorting one step forward by means of applicability of the mechanical sorting to the mineral industry. Because of the inefficient separation performance, dry separation of coal is very limited in industrial applications. Therefore, optical sorting depending on color differences between two minerals can be introduced to coal beneficiation systems. In this study, coal samples obtained from Konya-Ilgin region (Central Anatolia-Turkey) were separated by optical sorter and the results were evaluated. The conventional floatability tests for Ilgin coal are conducted by collecting most of the feed material at 1.3-1.4 g/cm3 density range. Separation of Ilgin coals with heavy medium methods will not be possible because of poor density difference between coal and its impurities. There are important color differences among the floated particles at 1.3-1.4 g/cm3 density range. Therefore, Ilgin coal is subjected to optical sorting in a pilot scale optical sorter. Different size fractions were fed to the optical sorter and then rejected and accepted particles by equipment were analyzed. Ash content of the accepted particles was reduced to 25-35 % and ash in tail increases up to 55-60 % after sorting. Although most of the material floated at low densities, optical sorter separated the feed into two different quality products. This study has the potential to clarify applicability of optical sorting even to non-floatable coals and to provide an important contribution to both industrial applications and literature.

Sep 1, 2012

By V. V. Lodeischikov

This paper covers some problems of treatment of complex gold ores and concentrates containing copper, lead, zinc, antimony and uranium. All these metals may present in ores both as major and associated components. The paper suggests recommendations for early determination of relative value of the metals in ores, which largely contribute to the selection of concentration and metallurgical flow sheets. The focus of this work is on treatment of complex ores in gold plants. The metal extraction technologies used by such gold plants are typically aimed at maximum gold recovery. Therefore, production of base metals as by-products requires significant updating of the existing process flow sheets based on economic, environmental and other considerations. At the same time, cooperation between gold plants and base-metal plants is of great importance. This paper provides an overview of worldwide existing and innovative processes of base metals extraction from complex and refractory gold ores.

Jan 1, 2014

By F. Waanders, Campbell. Q.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite where the specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials like silica, base metals and their oxides, usually associated with gravitation-gold-recovery-processes. The ore body investigated in this project originated from a gold reef containing a large portion of gold locked inside the gold pyrite complexes, which was mined and treated in a conventional way. After gold extraction, the material was pumped to a tailings dump and the gold extraction of this dump was investigated. In order to assemble a concentration plant setup, the head grade and size distribution of the dump and bulk sample were determined accurately. Chemical analysis and mineralogical examination were done on a representative sample of the bulk sample, to determine the chemical composition of the material. The results obtained thereof were evaluated and a pilot plant was configured. A bulk sample was processed in the pilot plant and the results were evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes.

Jan 1, 2014

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duvalm

Polyethylene glycol monoalkyl ethers (CnEm) render quartz hydrophobic while feldspar remains hydrophilic. As a result quartz can be separated from feldspar in small frothless flotation devices such as the Hallimond tube. The separation can be accomplished at room temperature at pH < 7 and C16E33 concentrations between 10-5 and 10-4 M for quartz particles smaller than 0.4 mm. No separation is observed when feldspar ore containing about 60 % of feldspar and 40% of quartz is subjected to flotation in a laboratory flotation machine. The reason for the lack of separation is a low hydrophobicity of quartz in the presence of polyethylene glycol monoalkyl ethers and high intensity of mixing in the flotation machine. The flotometric tests showed that the contact angle of quartz in monoalkyl ethers of polyethylene glycol solutions is less than about 18 degrees and depends on the structure and concentration of the ether and the pH of the system.

Jan 1, 2003

By Arkady Senchenko

The application of centrifugal separation methods with the use of gravity concentrators has been assigned high priority while gold-containing minerals processing. The separation proceeds under centrifugal force resulted from the rotor spinning and wash water flow in the concentrators. The high specific gravity particles are retained at the trapping surface of the cone, and the low specific gravity particles are brought in the tailings. The centrifugal field in such concentrators (Knelson, Falcon) is generated by the rotating cone provoking the swirling of the free fed slurry flow. The author investigated the regularities of the separation process in the centrifugal gravity concentrator where a two-phase flow of the separated mineral media is under the pulsed pressure of the fluidization water and air. As a result of the study the possibility of the deeper penetration of the fine heavy fraction into the cone rings, providing the fluctuation of the fluidization water or air flow, was theoretically argued and experimentally proved. This allows the increase of the separation performance at low pulsation costs. The developed mathematical models are in close conformity with the actual process of interest and they enable the prediction of the heavy phase behavior at the isolated process stages in the concentrator. Keywords: gold, centrifugal gravity concentrator, containing, specific gravity, cone ring, pulsation, cost, fluidization water, Knelson centrifugal separator

Sep 1, 2012

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By B. Gorain, O. A. Bascur

"The advent of digital revolution has now enabled us with numerous tools that could be leveraged to transform our operational data into actionable insights. Key opportunities with digitization include better visualization, transparency, integrated planning and execution for value-chain optimization, that results in smarter production, intelligent response to changes in ore, process and equipment conditions, reduce energy and waste along with prevention of asset breakdown, safety and environmental issues. It is important to realize that these digital tools have limited value, from a metallurgical operational context, if we cannot bring-in the appropriate domain expertise along with getting the basics right. The focus within Barrick is to ensure that there is adequate depth of different disciplines built into our platforms along with breadth to integrate other disciplines such as geology and mining for an effective Mine-to-Mill integration. A gold recovery improvement strategy based on optimal Gaudin size distribution, leaching performance monitoring and guidance via feed grade maps is discussed. Simultaneous identification of process and equipment constraints enable finding the best overall conditions for Gold recovery. This paper discusses the methodology, findings, and challenges in the ongoing journey of implementing a Metallurgy Analytics platform that evolves from being retrospectively descriptive to anticipatively prescriptive.INTRODUCTION The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stakeholders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance."

Jan 1, 2018

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.Simultaneously, the paper explores the mechanism of the flotation of Rare Earth minerals from intergrowth minerals. The infrared spectra for Dh and Rare Earth cation by analysis in theory shows that Dh formed chelate complex with Rare Earth cation and were adsorbed on the surfaces of Rare Earth minerals. The mechanism of the intergrowth minerals depressed by acid silica gel can be explained as gummy colloid hydrolyzed from acid silica gel which are selectively absorbed on the gangue minerals, making them hydrophilic and depressed, with pulp pH value of alkalescent."

Jan 1, 2003

By de Vaux. D.

Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis. The results obtained have demonstrated that water quality does play a significant role in flotation recovery at the experimental conditions used.

Jan 1, 2003

By William Skinner, Ishmael Quaicoe, Jonas Addai-Mensah, Ataollah Nosrati

To date, intractable ore specific operational challenges such as poor heap geotechnical stability, permeability and high acid consumption rates associated with low grade (~1 wt%) nickel (Ni) laterites still makes the adoption of heap leaching processing unattractive. This paper presents some highlights of drum agglomeration, column leaching and characterization studies undertaken to foster the understanding and knowledge of some of the desirable product attributes of -2 mm and -15 mm, low grade saprolitic (SAP) and goethitic (G) Ni laterite feed ores and their blends (SAP/G). For column leaching, 5-40 mm agglomerate beds were continuously irrigated with 200 g/dm3 H2SO4 solution at 8.5 dm3/m2/h rate over 100 days. Ni, Co, Fe, Al and Mn extraction rates, free acid concentration, agglomerate bed slump and structural changes were determined as a function of time. The results show that at equivalent feed masses, except -15 mm G which displayed slower, pseudo-layering based behaviour, all the feeds (single and blends) displayed coalescence controlled agglomeration behaviour at varying binder dosages. Whilst the agglomerate compressive strength of the G ore was markedly higher than that of SAP ore, those of the blends were substantially similar. At fixed column leaching conditions, the Ni/Co extractions and acid consumption were higher for SAP ore whilst the agglomerate bed slump was lower than those for G ore. The bed of agglomerates produced from -2 mm G/-15 mm SAP blend was more stable than that for the -2 mm G/-2 mm SAP blend agglomerate, the latter experiencing blockage within 24 h of acid irrigation due to agglomerates breakdown. The Ni/Co extractions and acid consumption rates obtained for agglomerates of -15 mm G/-2 mm SAP blend were lower than expected based on the ratios of the SAP and G ores within the blend composition. The findings suggest that judicious saprolitic and limonitic ores’ blending could reduce acid consumption rate, improve the agglomerate bed robustness and enhance bed percolation behaviour under prolonged acid irrigation periods during heap leaching of lateritic ores of variable mineralogy.

Jan 1, 2014

By J. W. Ahn

Calcined calcium oxide from limestone is hydrated to manufacture calcium hydroxide, and then precipitated calcium carbonate is synthesized from calcium hydroxide. Precipitated calcium carbonate of various morphologies is obtained by controlled conditions of each step and characteristics of limestone, calcium oxide and calcium hydroxide. Especially characteristics of calcium hydroxide have the most influence on morphology of precipitated calcium carbonate character. In this study, therefore, it is investigated the specific surface area of calcium hydroxide and morphology of precipitated calcium carbonate according to hydration temperature. Calcium hydroxide hydrated at high initial temperature has larger particle size than that hydrated at low initial temperature. And formation yield of aragonite precipitated calcium carbonate has improved by using calcium hydroxide had larger particle size (hydrated at high initial temperature).

Jan 1, 2014

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By I. Yu. Rasskazov, A. V. Rasskazova, N. M. Litvinova, N. A. Lavrik, V. G. Kryukov

The possibility of the intensification of the gravity processing of complex iron-manganese ore, which contains the finely dispersed inclusions of gold and platinum is shown. Clear mineral fractions of precious metals were sorted out of the different types of ores (quartz-braunite and carbonate- magnetite ore, ferruginous quartzite, carbon-containing shale, breccia-limestone and dolomite breccia). Composition and structures of precious-metals particles was detailed. The industrial content of platinum and gold was found. Precious-metals mineralization is character for all types of ores. High content of platinum is indicated in the carbonate-magnetite (up to 11.3 mg/kg) and quartz –braunite (up to 10 mg/kg) types of ore. Gold is presented in the ferruginous quartzite (up to 1.29 mg/kg) according to the data of the reduced mineralogical analysis. The composition of native platinum depends on the type of the ores: 1) quartz-braunite type contains isoferroplatinum (Pt3Fe) with Cu, Rh, Ir, Ru; 2) carbonate-magnetite type contains isoferroplatinum with Cu, Sn, Ni, Rh, Ir, Os; 3) pyritic-carbon ore contains isoferroplatinum with Sn, Ni; 4) ferruginous quartzite contains isoferroplatinum without admixtures. The ultrasonic treatment of mineral aggregates (P = 41.5 Watt, I = 15 W/cm2) made possible the liberation of fine particles of precious metals. Smooth-shaped or crystalline mineral aggregates are effectively liberated after acoustic treatment. Their surface is freed from impurities. The aggregates with the complex form and structure, which consist of the numerous plates and the grains, are not effectively liberated from impurities. It is shown that the ultrasonic treatment of aggregates with the fine inclusions of precious metals contributes to the liberation of the particles of platinum and gold and intensification of the gravity processing of refractory ore. This approach contributes the increase of the raw-material base of precious metals.

Jan 1, 2018

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003