Search Documents

By L. S. Gertsch

The production of minerals for human use at locations other than the Earth is expected to ?advance ? human prosperity in ? ways that [do] not compromise the potential prosperity and quality of life of future generations? (Brundtland, 1987); in other words, sustainably. This paper examines the interaction of extra-terrestrial mineral production (ETMP) with the following sustainability imperatives: ? The sustainability of human activities on Earth; ? The sustainability of human activities elsewhere; ? Human survival in general, the ultimate sustainability goal. Some of the consequences of mineral production on Earth are widely considered to decrease the future prosperity and quality of human life. Examples include noxious by-products or wastes and unsettling economic up- and downswings. Moving mineral production activities to extra-terrestrial locations, where appropriate, will decrease many of its deleterious effects. Terrestrial mineral production presently is decreasing in some countries and increasing in others, moving from the cheaper and easier ores to more expensive, difficult materials. When the full costs of maintaining the terrestrial environment in a sustainable manner are included, total mineral pro-duction costs must increase. The cost of extracting mineral products from extra-terrestrial sources will be substantially higher, especially in the initial phases, but as the full costs of terrestrial production increase, at some point in the future (different points for different minerals), the curves will cross (Fig.1). This will occur at different points for different materials, a process whose prediction will be complicated by substitution of cheaper materials for some uses as prices of the original material rise. In summary, mineral products from extra-terrestrial sources will tend to increase the sustainability of human civilization, once steady state has been reached.

Jan 1, 2014

By Xinyang Xu, Chen Zhang, Lixia Li, Zhitao Yuan

"Density functional theory was employed to clarify the mechanisms of the activation of a quartz surface and its collection by the flotation method at the molecular level. The calculation results indicated that hydrogen bonds on the quartz surface (1 0 1) existed in pairs while in contact with water. The simulation was carried out to investigate the different effects of Ca2+ and Ca(OH)+ on a quartz surface with hydrogen bonds, and the results suggested that Ca(OH)+ most likely adsorbed onto and activated the quartz surface. Mulliken population analysis of the external oxygen atom of the quartz surface, calcium atom of Ca(OH)+, and the oxygen atom of oleate showed that there were electron transfer and the formation of a chemical bond between Ca1-O1 and Ca1-O3, which were indicative of strong interactions between the three atoms. In addition, the –OH of the Ca(OH)+ contributed to the activation, which suggested that the Ca(OH)+ group acted as a bridge between the surfaces of oleate and quartz.INTRODUCTIONFlotation is an effective separation method in mineral processing that takes advantage of the physicochemical differences between minerals and gangue, and the properties of the mineral surfaces play a key role in this process (Liu et al. 2016, Qin et al. 2017). In the reverse flotation process of iron ore, gangues are captured by cationic or anionic collectors and floated with air-bubbles as tailings, and the pre-depressed iron oxide minerals are left at the bottom as concentrates (Lima et al. 2013, Yianatos et al. 2015, Zhu et al. 2015). Quartz (SiO2) is one of the major gangues of hematite ores and cannot be easily removed. It is a naturally hydrophilic mineral, in which silicon is the cation in its crystal structure and has very limited solubility. Therefore, quartz must be activated, usually by metal ions, for its effective rejection as a float-product by reverse flotation (AIME. et al. 1976)."

Jan 1, 2018

By P. Somasundaran, G. Anastassakis, Z. Pan, D. R. Nagaraj

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By R. D. Alorro

Melting has become a popular pre-treatment method for municipal solid waste (MSW) incineration residues in Japan. Although the method is effective in stabilizing the hazardous organic sub-stances such as dioxin, it concentrates the heavy metals such as Zn, Pb, Cu, and Cd in a newly formed fly ash (melting fly ash). Melting fly ash is classified as a hazardous waste because of the leaching potential of these heavy metals in landfill environment. Extraction and recovery of these metals seem to be more environmentally and economically attractive than disposing the material to landfill after immobilization process. This study proposes a Carrier-in-Pulp (CIP) method as a new hydrometallurgical route to reject and recover heavy metals from fly ash. In this method, a carrier material which recovers the extracted metals is added simultaneously with fly ash to leaching solutions and is harvested from the pulp by physical separation method like magnetic separation or sieving. To demonstrate the effect of CIP method, shaking flask experiments were conducted under various conditions using NaCl solution as lixiviant and iron powder or granular activated carbon as carrier materials. In the CIP method using iron powder, more than 97 wt% of Pb and Zn were extracted from the ash to the solution phase. However, the iron powder which was harvested from the pulp by magnetic separation, recovered only Pb (more than 94%) through cementation, leaving behind Zn ions in the solution phase. Due to this problem, granular activated carbon (GAC) was considered as an alternative carrier material. Single- and multi-metal adsorption experiments using granular activated carbon were conducted as a preliminary study. Around 85% Pb and 88% Zn were recovered by GAC in the single-metal adsorption experiment, while 60% Pb and 70% Zn in the multi-metal experiment. These results showed that activated carbon was superior to the iron powder since it was able to recover both Pb and Zn through adsorption. The leaching test conducted on the residue after the CIP-Fe treatment revealed that the solubilisation of Pb was successfully suppressed to meet landfilling guidelines.

Jan 1, 2014

Optimising flotation designs and innovations is a complex process involving many parameters, one of which is ensuring sufficient testwork is carried out at plant level before these innovations are launched in the marketplace. This paper will describe how modern design tools are utilized, what are testwork phases at various plants and how results and observations have helped to validate and optimise flotation design innovations. Scale-up of equipment has long been the prevalent trend, but how long can it continue? Are there other means for pushing the boundaries of present technology? Some present challenges and future directions are given in the light of theoretical criteria for scale-up and how it has been applied in practice. Very large flotation cells of 300 m3 size have been installed in New Zealand, and relevant results from the metallurgical and mechanical aspects are presented and discussed. Utilization of the cell volume is also important. New innovations in the hydrodynamic domain are presented and discussed. Means to enhance flotation of coarse and fine particles are shown with results from plant testwork. Accurate control of large flotation cells is vital to optimize yields and grades. Froth image analysis and intelligent level control are presented ? again - with relevant plant results.

Jan 1, 2014

By Aidan Giblett, Karen McCaffery, Robert Dunne

"A worldwide decline in competency levels of practicing metallurgists over recent decades has become clearly evident and is a common topic of discussion among senior practitioners and professional associations. The associated impacts on the industry are material and include operational inefficiencies, missed optimisation opportunities and suboptimal new plant designs. There are many contributing factors to this condition. Decrease in competency is particularly evident both in regions where imbalance between supply and demand has led to a general reduction in experience levels for comparable roles over time and in emerging regions where a rapid rise in demand for practitioners has occurred in conjunction with rapid economic development and industrialization. The context, depth and breadth of education curricula and levels vary with location such that solutions to the technical competency dilemma may need to be developed specifically for each region with these influences in mind. Delivering, demonstrating and maintaining competencies are a critical requirement of undergraduate training and ongoing professional development. Other factors such as generational and cultural characteristics and expectations, political influences, role requirements and employment reward and recognition systems all play a critical role in determining if core competencies can be effectively developed, applied and subsequently maintained. This paper reviews factors impacting and some common approaches to competency development. The authors’ experiences in the management of professional development efforts within the global industry are reviewed and a blueprint proposed to address industry requirements in this area."

Jan 1, 2014

By Y. F. Guo

Laboratory scale experiments were conducted to produce titanium-rich material from Panzhihua ilmenite. The results showed preoxidation with sodium salt additive especially for Na2B4O7 signif- icantly advance the reduction of iron in Panzhihua ilmenite. Acceleration mechanism of preoxidation with Na2B4O7 has been studied here. The maximum metallization of iron 92% can be obtained under conditions of preoxidation at 850? for 30 min and subsequent reduction at 1100? for 150 min. The rusting separation technique to reduced ilmenite has been further studied, obtaining titanium-rich product with TiO2 over 82% and the recovery of TiO2 above 97%.

Jan 1, 2014

By P. T. Nguyen

The analysis of particle capture by an air bubble by two separate phenomena of collision and attachment has been difficult due to the uncertainty in determining when and where the two phenomena begin and terminate at the bubble surface, respectively. Therefore, a unified analysis was developed by solving the motion equation for the particle capture as one process. No distinction be-tween collision and attachment was made. Both the liquid film described by the micro-hydrodynamic resistance functions and the surface forces were included in the new model. The model predictions with the DLVO (Derjaguin-Landau-Verwey-Overbeek) surface forces did not agree with the experimental trajectories of latex and silica spheres. The model predictions with the inclusion of the non-DLVO attractive surface force agreed with the experimental data. The non-DLVO force reduced the repulsion between the non-attaching particle and the bubble, and significantly increased the attraction between the attaching particle and the bubble. The unified analysis is capable of predicting particle capture without the use of the induction time. The unified analysis also shows significant influence of the short-range hydrodynamic interactions on the collision which has been previously ignored.

Jan 1, 2014

By Erico Tabosa

The turbulence characteristics and measurement techniques for agitated tanks are well established for liquid and liquid-gas systems. However, the literature shows that the overall energy dissipation rate (related to turbulence) is affected not only by air addition, but also by the concentration of solids. Unfortunately, there are no reliable measurement techniques for characterizing turbulence in a three phase (liquid-solids-gas) environmental system, which is the case in a flotation cell. Therefore, the effect of turbulence on flotation kinetics is very much one of conjecture. The aim of this work was to develop a sensor to characterize the degree of velocity fluctuation, which is related to turbulence, in a flotation cell operating with slurry and air. This sensor comprises a piezoelectric film transducer that converts mechanical to electrical energy. Hence, when the sensor deflects backwards and forwards an AC voltage is created. Flotation studies carried out using this sensor in a 3m3 Metso RCS cell processing a copper sulphide ore showed a highly turbulent impeller zone with transition to a significantly less turbulent zone in the upper portion of the cell. The transition region moves as the cell operating variables are changed, for instance the impeller speed, impeller size, air rate and feed solids concentration. Keywords: mechanical flotation cell hydrodynamics, turbulence characterization

Sep 1, 2012

Under the AMIRA P9 project the three-product cyclone-an off-shoot of the conventional hydro-cyclone-that produces three distinct products has been developed. The three-product cyclone shows great promise as a classifier in mineral processing. Industrial and pilot plant trials performed to assess its performance in the classification of the UG2 platinum ore, indicate that the presence of an extra overflow product stream that captures the mid-sized particles, provides improved classification efficiency. To assess the split on component density, samples from the feed and product streams were screened and assays by size for chromite (? = 4.8) and silica (? = 2.65) were obtained. Results from tests performed using this type of hydrocyclone in a number of applications indicates that it can be applied successfully in circuit configurations where the conventional hydrocyc-lone is not suitable. Utilising the three-product cyclone to classify the UG2 platinum ore resulted in an intermediate overflow product stream containing the mid-sized low density silicates and relatively fine high density chromite particles while the finer overflow contained mostly fine silicates and chromite particles. The coarse chromite and silicates reported to the underflow. Due to the increased number of products, the method of using efficiency curves was extended to cater for the increased number of products in the three-product cyclone. Although significant differences in the classification performance of the three-product cyclone were noticed with variations in machine variables a consistent method of assessing the performance was applied. The efficiency curve was adopted and applied and separate efficiency curve properties were obtained for each product stream. The methodology was applied to the component data, and efficiency curve proper-ties for each key component were obtained and compared. This paper discusses the application of the efficiency curve to cyclones producing more than two products and extending the methodology to the different components in the feed.

Jan 1, 2014

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

By Irena Grigorova

"Vermiculite is a naturally occurring mineral compound composed of shiny flakes, resembling mica. Worldwide, vermiculite has been used in various industries since 1920. When heated to a high temperature, flakes of vermiculite expand several times their original size. The expanded vermiculite is a lightweight, fire-resistant, absorbent, and odorless material. These properties allow vermiculite to be used to make numerous products, as an additive, for example to potting soil, in agricultural, construction, horticultural and industrial applications, including pesticides, insulation, potting mixes, brake pads, sound deadening materials, fire protection, paints, sealants, insulating concrete and etc. Over recent years researchers have been looking for effective economic and environmental methods and solutions for fine technological waste utilization. As a result of vermiculite ore processing large quantities of fine waste dust are formed. Until now there has been no application for this waste product. Currently this waste product is stockpiled using valuable land space, and is a potential contaminant. The paper presents the results of a study on the possibility to obtain briquettes from fine vermiculite by-product. The particle size distributions, chemical and mineralogical compositions of vermiculite were determined. It was established that consolidation of vermiculite dust by methods of briquetting and its consequent application in agriculture as meliorants for physico-chemical treatment, improves soils aeration structure and properties."

Jan 1, 2014

By M. Evertsson, M. Johansson

"In minerals processing control is vital to increasing performance and output of a plant. Model predictive control (MPC) is one of the most effective control strategies used in process industry. Sbárbaro (Sbárbaro and Del Villar, 2010), Asbjörnsson (Asbjörnsson, 2015), and Légaré (Légaré et al., 2016) have for example highlighted the possibility to simulate, develop and tune control systems using plant simulators within minerals processing. In more recent years the use of model predictive controllers have increased, and many process industries now utilize more advanced control methods to regulate their processes, raising the question regarding how to, build, test and verify a proposed control solution successfully. In this research, a linear model predictive controller is formulated and applied to a simulator of an existing tertiary crushing circuit. The circuit has in previous work by Johansson (Johansson, 2017) been modeled in MATLAB Simulink and calibrated relative plant data to an average error of less than 10% over 8 hours of production. The work demonstrates how to formulate the controller model structure to describe conveyor belts, storage components, screens, crushers, and control objectives for a minerals processing circuit. The work illustrates how to apply and successfully evaluate possible upsides in a circuit. The advantage of a crushing circuit simulator is that it can be configured, tuned and modified in any possible way, which is of great benefit to developers and engineers. Additionally, examples of how to use estimated measures to improve the performance of the plant are demonstrated. The control performance is finally evaluated for three different controller configurations."

Jan 1, 2018

By Chao Li, Kym Runge, Saeed Farrokhpay, Dee Bradshaw

"It is well known that froth phase has a controlling influence on the overall flotation performance. Froth recovery is expected to be affected by froth transportation behaviour. The latter has been represented by different volume balance and energy balance based models. In froth transportation models based on a volume balance, the froth phase is divided into different zones. The total froth residence time is the sum of the time spent in each zone and is dependent on the cell geometry, bubble burst rate and the position that bubbles enter into the froth phase. Alternatively, the froth transportation model based on an energy balance treats the froth phase as a block. In this model, froth height above the concentrate lip is being predicted by minimising the energy of the system which is dependent on the froth geometry, froth stability and froth rheology. The froth height can be used to calculate the froth efficiency of delivering mineralized bubbles from the pulp to the concentrate lip. This paper critically analyses the current models of froth transportation in flotation, and examines the limitations of these models. The importance of froth rheology, which is the resistance to the froth flow towards the discharging weir, in determining froth transportation, is also highlighted."

Jan 1, 2014

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By E. A. Bekchurina, Yu. P. Morozov

"This paper presents the results of a study of the concentration of flotation froths in tapered chutes. The tests were conducted on lab and full-scale plants, and the results obtained were mathematically processed. The kinetics of monophase recovery from a stationary flotation froth, hydrodynamics of froth flows traveling in a tapered chute were investigated. The effect was studied of the mass fraction of the valuable component in the chute feed, yield of the chute’s overflow, and chute design on the concentration performance. Processing of the collected data revealed the general laws of the process and allowed to develop a technique for modeling concentration of the flotation froths of sulphide copper ore in a tapered chute to predict the performance without testing. It was found that concentration in tapered chutes allows to obtain products that are comparable in quality with froths after one or several cleaner flotation stages.INTRODUCTIONThe present production expansion rates require continuous improvement in the grade of flotation concentrates, while the grade of the mineral feed is constantly deteriorating. This leads to a significant complication of flotation flowcharts. Flowcharts become multi-staged with multiple cleaner flotations, negatively affecting the production costs.In recent years, researchers are paying close attention to the processes occurring in the froth layer in the flotation cells. Improving the concentrate grade is facilitated by secondary concentration of minerals in the froth layer, which consists in fixing the hydrophobic particles released as a result of the coalescence of the bubbles of the upper layer when moving downward at the liquid-gas interface of the froth layer. In this case, the released hydrophilic particles, trapped in the froth layer as a result of mechanical removal, migrate from the froth together with the liquid phase."

Jan 1, 2018

By Jihoe Kwon, Daeyang Lee, Mario Fujimura-Kashiwagui, Heechan Cho

"Calcium carbonate is one of the most widely used mineral in today&apos;s industries such as plastic, paper and pigment. There are many essential physicochemical properties required by each industry field but the most common requisite is size. One way to achieve appropriate size is grinding. Grinding is typically an energy intensive process, consuming about 40% of total energy cost in mineral process. Due to that reason, optimization of grinding process is a critical element to achieve price competitiveness. Two different type of grinding apparatus were hired to find out optimum condition in terms of energy efficiency. Utilizing samples containing 10, 20, 30 and 40% solids concentrations, a 1l batch type attrition mill was operated as the first grinding step at various operating speed with 1? to 5? grinding media in order to study the optimum operating conditions to reach submicron particles. Next, a 0.15l vertical beads mill was tested as next step with 100? to 500? grinding media to study the optimum conditions in the submicron range. Net energy and the specific energy input was measured to reach stated size ranges. Also, using a back-calculation based on the population balance model further operating conditions were studied. There were several competitive combinations which showed significant energy efficiency improvement when compared with the single step grinding."

Jan 1, 2014