Search Documents

By A. A. Lavrinenko

There are discussed the possibilities of using of flotation tailings of platinum-copper-nickel sulfide ores of the Norilsk region for the preparation of backfill mixture instead of a specially produced rock and binder materials to reduce the cost of stowing operations and impact on the environment. It is shown that due to the presence in the tailings of flotation up to 10% of sulfide sulphur, which reduces the strength of the fill materials, and more than 1 g/t PGM it is necessary the preliminary extraction of the sulfides in the product for further processing that give an opportunity to reduce the losses of valuable components. It is shown that by the flotation of the current tailings it is possible to extract 91% of sulfide sulphur, 60% of palladium and 30% platinum in 17% sulfide concentrate containing 2.1 g/t palladium, and to reduce the sulphur content in the tailings up to 0.7%. Due to the easy oxidation of pyrrhotite, there is recommended fractional delivery of the collector with a total consumption 200 g/t. There are discussed results of the flotation study with an additional collector of PGM (sodium diizobutyditiophosfinate), which one show the possibility to increase extraction of platinum on 45%, as well as extraction of sulphur and palladium. For the flotation of sulfides and PGM from the current tailings there is recommended a combination of collectors for primary flotation and only butyl xanthate using in control operations. The possibility of using sludge fraction of the current tailings as a component for the preparation of the combined cementing materials after exposure of sulfides is analyzed. It is shown that the efficiency of the flotation of sulfides from this fraction can be enhanced using selective flocculants. There are discussed the advantages of implementation of completely hydrophobic butadiene-styrene copolymer in comparison with partially hydrophobic polymers. There is discussed an efficiency of the mechanochemical treatment of old tailings in turbo mill and sulphuric acid to remove oxide films from the surface of pyrrhotite before its flotation. Due to the pretreatment operation there is achieved increasing of sulphur extraction and after the introduction to the flotation circuit three control operations there is produced the fill material with sulphur content 2.5%. Keywords: tailings, copper-nickel ore, pyrrhotite, butyl xanthate, sodium diisobutyl dithiophosphinate, selective flocculation, butadiene-styrene copolymer, mechanochemical treatment

Sep 1, 2012

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

By Ataollah Nosrati

Agglomeration of fine mineral particles is an important step in heap leaching processes employed for a cost-effective hydrometallurgical extraction of value metals from low-grade ores. In this study, the effect of acidic binder composition and feed ore particle size on binder dosage requirement and isothermal, batch agglomeration behavior of siliceous goethite nickel laterite has been investigated. Agglomeration tests performed with tap water and 30, 44 and 98% w/w H2SO4 solutions as binders revealed the key role of binder formulation in controlling ore particle wettability, nucleation and granule growth behavior. Both lower binder acid content and higher dosage led to greater wetting, nucleation and granule growth rates. Variation of feed ore fine/coarse particles? mass ratio dramatically impacted on binder dosage requirement for effective particle wetting, nucleation, and growth agglomeration behavior. Increasing fine (-150 µm) fraction mass content in a -2 mm feed ore, led to higher binder dosage requirement and enhanced nucleation, however the overall agglomeration rate/granule size growth decreased. In contrast, the presence of coarse (5 ? 15 mm) particles in feed ore led to (i) lower binder dosage requirement, (ii) enhanced initial agglomerate size growth rate, and (iii) reduced coalescence. For dry agglomerates of similar sizes, competent coarser feed particles led to remarkably higher compressive strength than did finer feed particles. Microstructure analyses indicated that the granules containing coarser particles exhibited a distinctive, competent core/shell (fines) structure which led to their structural reinforcement. The appropriation of the findings for optimizing agglomeration behavior for enhanced heap leaching of complex, low grade laterite ores are discussed in this context.

Sep 1, 2012

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-the-art, custom designed xray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. Utilization of this custom designed cone-beam x-ray microtomography system is discussed. Applications described include: coal washability analysis for the design and operation of coal preparation plants, liberation analysis for evaluation of grinding practice and separation efficiency, mineral exposure analysis for prediction of the ultimate recovery from heap leaching operations, and analysis of the pore structure network of packed particle beds for simulation of flow through such porous structures as encountered in filtration and heap leaching.

Jan 1, 2003

By Hong Zhong, Shuai Wang, Xin Ma

"In this paper, we report a simple and effective process for producing a surfactant mixture of O-isopropyl-N-ethyl thionocarbamate (IPETC) and 4-(tert-butyl)benzyl mercaptan (BBSH). The composite collector was synthesized via one-pot reaction of sodium isopropyl xanthate, 4-tert-butylbenzylchloride and ethylamine using tert-butyl alcohol as solvent. The whole process for the synthesis of composite collector involves neither foul smelling reagents or intermediates, nor any by-products requires special treatment for disposal, and thus can be scaled up to an industrial level. The flotation response of chalcopyrite and pyrite independently with IPETC and BBSH collectors and with their mixture (the mole ratio of IPETC and BBSH is 1:1) was assessed. The microflotation results showed that the collecting ability of BBSH was slightly stronger than that of IPETC and that IPETC was more selective collector than BBSH against pyrite, and that the composite collector displayed a stronger collecting ability toward chalcopyrite than IPETC, and superior selectivity for chalcopyrite against pyrite than BBSH. The batch flotation results showed that composite collector exhibited better performance than IPETC and BBSH. It was demonstrated that the mixing of IPETC and BBSH would give rise to a synergistic effect significantly enhancing overall flotation performance. In addition, the adsorption mechanism of BBSH on the surface of chalcopyrite was conducted by adsorption test and infrared spectrum measurement, and the results showed that the interaction of BBSH on the chalcopyrite surface was dominated by the chemical adsorption, and the formation of a strong S-M bond plays a key role in the adsorption of mercaptans on minerals surfaces. The developed flotation reagents with special preparation method is the author’s original design, patented (patent of the People’s Republic of China) and have no analogues in the world of mineral processing. (Application number 201810100107.1, ""Alkyl thioether alcohol compounds, methods for their preparation and applications thereof "", China).1. INTRODUCTION Froth flotation is an essential method widely used in the mineral processing industry to selectively separate valuable minerals from gangues[1]. Worldwide, more than 109 tons of materials are treated annually by this method with the majority being metal sulfides and oxides[2]. Nowadays, the judicious utilization of complex sulfides to meet the ever-growing demand of mineral resources gains more attention, due to the gradual depletion of deposits with high grade, making imperative the development of new high-efficiency collectors and mixtures of collectors to process complex minerals. In comparison to individual collectors, the use of mixtures has several notable benefits including lower dosage requirements, improved selectivity, rates and recovery and an increase in the recovery of coarse particles[3-9]. Moreover, in terms of cost and environmental issues, using collector mixtures can reduce the total amount of agents used, thus reducing the overall effect on the environment and economic costs without affecting the flotation performance. Therefore, the search for high-efficiency mixtures of collectors is still interesting and relevant."

Jan 1, 2018

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By G. C. Li

Gold extraction using iodide leaching from refractory carbonaceous gold ores was studied. Thermodynamic analysis of iodide leaching chemistry had been carried out. Eh-pH diagram of Au-I2-I--H2O leaching system showed that the coordinating active forms from iodides were I3- and I-, while the major coordinate compound formed during iodide leaching was AuI-. For leaching parameters optimization, technological parameters such as I2 concentration, I2 :I- ratio, oxidation assisting agents, liquid/solid ratio, and leaching duration were studied. The leaching results showed that the average Au leaching rate reached 91% and 92% for oxidized ore and roasted primary ore respectively. Leaching process proceeded in weekly acidic or neutral slurry at ambient temperature; the leaching duration was 4 hours. After that gold was extracted from the pregnant liquor by activated carbon adsorption ? desorption ? electrowinning process. Gold recovery was over 93% in the adsorption process, while the gold recovery in electrowinning process was about 95%, provided that the initial gold concentration is 40mg/L or larger. For iodine regeneration it is enough to add hydrogen peroxide in excess into the filtrate after gold electrowinning, all the iodides existing in the solution in any forms would be precipitated in the form of elemental iodine.

Jan 1, 2014

By A. Chattopadhyay

Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex, ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.

Sep 1, 2012

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018

By S. A. Kubyshkin, A. A. Agafonov, A. L. Shakhnin, S. M. Sukharzhevsky, A. A. Komlev, N. V. Vorob’ev-Desyatovskii, A. Pichugina

Cyanidation of gold ore results in formation not only of Na[Au(CN)2], but also cyanometallate complexes of some transition metals. During subsequent gold extraction from such solutions and pulps, using activated carbons (??), a number of problems arise. An effective solution of the problem is not possible without detailed knowledge of the interaction mechanism of transition metals cyanide complexes with AC particles. The chemical properties of AC particles and graphene, saturated with [?u(CN)n](n-1)- (n=2, 3), were studied by XPS, ESR, SQUID, and DFT. The obtained results were compared with the data on AC adsorption of anionic form of Ag(I), Au(I), Cd(II), Hg(II), Cr(III), Fe(II), Fe(III), Co(III), Rh(III), Ni(II), Pd(II), Pt(II) and Pt(IV) cyanide complexes. The adsorption of [?u(CN)n](n-1)- (n=2, 3) on AC from aqueous solutions in air is accompanied with oxidation of ?u(I) atoms. Besides, Cu(II) and Cu(III) compounds were found on AC surface. Quantum-chemical calculations confirmed the possibility of formation of Cu(I) complex with carbene-like sites of AC. The reactions of [?u(CN)n](n-1)- (n=2, 3) complexes and aromatic carbenes and their cation-radical were theoretically studied at DFT PBE level to obtain the information on adsorption of cyanometallate complexes on AC. Carbenes with different fragments were regarded as a model of activated carbons, which have free edge sites with paired o and n electrons. It was shown that [Cu(CN)2]- bounds firmly with triplet carbene, if one Cu-CN bond breaks. The dissociation process occurs through a multi-step spin-crossing mechanism to reduce total spin multiplicity of the metal-carbene complex. The behavior of transition element complexes in contact with AC in aqueous solutions is determined by the following characteristics: geometrical structure of ionic complexes; nature of ligands bonded to the central atom; concentration of reactive oxygen species in solution and its pH; nature of binding sites of AC.

Jan 1, 2018

By M. L. Cao

In this study, a montmorillonite organo-intercalation compound (MOIC) was synthesized by using a Na-modified bentonite (NaB) as a matrix and hexadecyltrimethylammonium (HDTMA) bromide as an intercalating reagent under microwave irradiation. The synthesized products were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), organic carbon content measurement, and adsorption density determination. The results show that, at 10% suspension concentration and 10 minutes irradiation in a 130-W microwave oven, the basal spacing d(001) of the synthesized MOIC increases to 2.209 nm from the original 1.218 nm of NaB. The MOIC has much higher adsorptive densities to nitrobenzene and aniline from aqueous solution than the NaB. The adsorption isotherm of nitrobenzene on the MOIC is linear, and the adsorption is mainly the result of nitrobenzene?s preferred partition in MOIC over aqueous solution due to MOIC?s hydrophobicity. The adsorption isotherm of aniline on MOIC follows the Freundlich equation and the increased adsorption is not only the result of aniline?s preferred partition in MOIC over aqueous solution but also that of the MOIC?s surface adsorptions.

Jan 1, 2014

By Reinol Compañero, Ivy Gonzales, Herman Mendoza, Brian Buenaventura

"The extraction of gold in the Philippines has been a significant challenge for the past decades. Around 70-75% of gold mined in the country can be accounted from the small-scale mining industry which primarily use the traditional cyanidation and amalgamation; processes which have been advocated due to its adverse affects to health and environment. To address this challenge, an alternative clean and sustainable technology was developed for the small-scale miners to recover gold and other metal/mineral values efficiently from Philippine ores. An initial survey was conducted and followed through with extensive mineralogical investigations ascertain the best method applicable. It was determined that Philippine gold occur in ore as (1) very fine particles in the microns range, (2) free-milling, which is in abundance, and (3) locked particles with sulfides --- it was concluded that enhanced gravity concentration and flotation are viable alternatives. A comprehensive test regime was followed to check the response of the ores obtained from different small-scale mining districts across the country. It was shown conclusively that the gold ores respond positively, with recoveries using gravity concentration and flotation of at least 95% and 88%, respectively; exceeding the nominal recoveries using cyanidation or amalgamation. A specific process flow was designed for each type of ore with customized parameters. It was determined that while capital expenditure of implementing these alternative processes is higher than what is currently being used, the operational aspects show that it is much more economical to apply enhanced gravity and flotation. It should be noted that the process developed addresses the critical issue of environmental costs which should be more than enough to justify the shift from the current to the novel and sustainable technologies."

Jan 1, 2014

Low-grade ore bodies, increase in rock competency, finely disseminated valuable minerals in the ore bodies, ore variability and water scarcity are among the technical challenges faced by the mining industry. These challenges have increased the business risk, capital investment and operating cost of the mining projects. Since the last 20 years, many large-scale concentrators have been built to cope with the above-mentioned challenges. Comminution, especially the fine grinding is an energy-intensive process. For example, the ball mill has a limitation in the fine grinding regime where the energy consumption increases exponentially when the product size is below 45 µm. The industry has been seeking for solutions that have a minimum risk and total cost of ownership. The stirred milling technology such as the TowerMill is well accepted by the industry as it has demonstrated the attributes required for fine grinding. TowerMill is a matured technology that has been adopted since the 80s for regrinding duty. Recently, this technology was installed in secondary and tertiary grinding duty to prepare a finer feed to rougher flotation. Four units of TowerMills were installed in a magnetite concentrator in Western Australia in tertiary grinding duty. Recently, Nippon Eirich has conducted process performance evaluation on the TowerMill circuit. The outcome of the exercise had indicated that the circuit is consuming 3.4 kWh/t to reduce from 55 µm to 35 µm with a narrow product size distribution. The effect of operating variables such as the specific energy, grinding media size, mill content % solids and mill feed configuration on the grinding efficiency were evaluated at the plant scale. Furthermore, the scale-up methodology was validated. The scope of this paper includes the performances of TowerMill and the validation of scale-up methodology.

Jan 1, 2018

By K. Kiangi

On installing the Metso Superior MK 54x75? primary gyratory crusher in Nkomati mine the crusher experienced severe power spikes greater than 1000kW which subsequently led to the crusher tripping under load while processing some of Nkomati?s MMZ ores. Likewise significant losses in throughput were also experienced while processing some of Nkomati?s MMZ ore types. Interestingly the crusher was capable of processing the PCMZ ores without experiencing any power spikes or losses in throughput. Investigations into the challenges faced by the crusher while processing Nkomati?s MMZ ores were conducted using the DEM model in conjunction with the fast breakage model present in Metso?s High Fidelity Simulator. The intentions of the study were to establish the most suitable operating conditions or cavity design that would potentially enhance the performance of the crusher. Likewise an understanding of the effects the feed conditions (size distribution and hardness) had on the crusher?s performance was established. Ore characterization tests were conducted on Nkomati?sPyroxenite, Diabase, Calc silicate and quartzite ores which were from Nkomati?s MMZ ore body. The ore characterization tests conducted were drop weight tests, slow compression tests and elastic modulus tests. Four simulations were conducted used the existing cavity design with various open side settings (OSS) and throws. This established the effects of changing the crusher?s operating conditions on its performance. Four additional simulations were conducted on two cavity designs with reduced volumes. This established the effects of changing the crusher?s cavity design on the crusher?s performance. Thus through the simulations a better understandings of the impact of the crusher design, operating conditions and feed conditions on the crushers performance. Furthermore an analysis of the crusher?s performance was made which was used as a basis for comparisons with the base case simulation. Keywords: crusher, discrete element method, simulation, ore characterization

Sep 1, 2012

By Kwan Ho Kim

The beneficiation study of low quality pyrophyllite is conducted to enhance the value of it by selective grinding. In mining stage, the main gangue mineral is quartz, and the content of quartz in ore has an adverse effect on the quality of pyrophyllite. Using the huge difference in hardness between quartz and pyrophyllite, the selective grinding is accomplished using stirred ball mill. As a result, a finer pyrophyllite particle can be easily separated from coarser quartz particle by simple size classification, and the content of Al2O3 of fine particle smaller than 45um increased largely. It means that the pyrophyllite particle is ground selectively compared to the quartz particle, and the quality of pyrophyllite is enhanced.

Sep 1, 2012

By Leming Ou, Qiming Feng, Yiping Lu, Pengyu Zhang, Qing Shi, Kun Liu, Guofan Zhang

"This paper introduces the mineralogical analysis of certain polymetallic copper-zinc ore in China with the aim of improving the flotation process. The main valuable elements, mineral phases and compositions of run-of-mine ore were inspected by the X-ray Fluorescence (XRF) and chemical analysis. For a deep known of the old process defects, Mineral Liberation Analysis system (MLAs) was employed to investigate the minerals liberation degree of selected key slurry points. Analysis results show that the run-of-mine ore belongs to the original copper-zinc polymetallic symbiotic ore at low oxidative level, which mainly contains 0.16% Cu, 4.43% Zn and 0.88% Sn. Gangue minerals are mainly silicate minerals, and zinc mineral is sphalerite. MLAs test illustrates that about 86% sphalerite has been dissociated in zinc flotation feed. In the current flotation process, over grinding of sphalerite monomer and insufficient liberation of intergrowths are the key problems need to be solved imminently. Up to this point, a new process consisted of two steps roughing unit is submitted in this research. It contributes two positive effects on zinc flotation performance: (i) separating sphalerite monomer timely to decrease overgrinding; (ii) improving zinc minerals intergrowths liberation efficiency. Flotation results indicate that the zinc concentrate grade increased 0.90% and the recovery improved 0.96% in the new flotation processINTRODUCTION Mineralogical analysis mainly focusses on solving mineralogy problems in minerals processing, assisting in minerals behaviors prediction and control for separation engineering (Falkovich, et al., 2001; Hillier, et al., 2003; Schouwstra and Smit, 2011). Process defects searching becomes its ordinary work, and flotation optimization appears to be its targets gradually. For example, Lucky Friday mine company (Idaho America) fails to obtain qualified lead concentrate as the change of ore properties (Nadoll, et al., 2011). Mineralogical analysis ascertains that there are too many dissociated sphalerite, pyrite and gangue particles exist in lead concentrate. According to this, more cleaning units are added to solve problems effectively. Kanowna Belle mine (Australia) takes a flash circuit in operation successfully with the aim of optimize flotation process, under the helps of mineralogical analysis and industrial test (Newcombe, et al., 2013). Lotter N.O. (2011) gives a deep description on how mineralogical data assisting mineral processing engineers to design and optimize flowsheet. For decades, quantitative and automated mineralogy techniques (Andersen, et al., 2009; Gu, et al., 2012; Oghazi, et al., 2009; Yu, et al., 2007) get well developed and hugely improve the veracity and repeatability of minerals properties measurement. Among these, MLAs (Gu, 2003) provided by JKMRC (Julius Kruttschnitt Mineral Research Center) is critically acclaimed all over the world. This analysis system can measure mineral phases composition and content, particles size, minerals occurrence and liberation degree directly."

Jan 1, 2018