Search Documents

By W. Krieglstein

Due to the natural variability of ores, it is necessary to carefully test flotation behavior of flotation cells before designing flotation circuits. For performing quick and versatile tests in the laboratory, Siemens developed a laboratory-size Hybrid Flotation Cell, which has been down-scaled from the 300 m³/h production cell to a 0.6 m³/h flotation cell. This small cell is being used as a test bed for technical and chemical concepts, the improvement of decisive components and the characterization of customer ores. In this study the evaluation results for Andean porphyry copper ores are shown. Total recovery rates of the order of 45 to 50 % have routinely been achieved in a single flotation cycle over a wide range of feed grades. In addition, the Hybrid Flotation Cell has proven to be particularly well suited for the flotation of fine particles below 20 µm down to below 1 µm, at high recovery rates and concentrate grades.

Sep 1, 2012

By H. B. Zhou

The process of bioleaching marmatite using moderately thermophilic bacteria has been studied in this research by comparing marmatite leaching performance of mesophilic bacteria and moderately thermophilic bacteria and valuating the effect of venting capacity on marmatite leaching performance of moderately thermophilic bacteria and the effect of pulp densities on marmatite leaching performance of moderately thermophilic bacteria. The results show that moderately thermophilic bacteria have more advantages over mesophilic bacteria in bioleaching marmatite. Aeration agitation can improve the transfer of O2 and CO2 in solution and promote the growth of bacteria and therefore, enhance the leaching efficiency. With the increase of pulp density, the total leaching amount of valuable metals increased, however, the extraction efficiency decreased due to many rea-sons, like increasing shear force that results in poorly growth condition for bacteria, etc.

Jan 1, 2014

"The most common comminution testing methods and the associated analytical procedures provide average values and do not capture the variability in breakage behaviour of ore particles. Therefore, plant designs and process performance predictions use only average values; hence, the inherent variability that exists within an ore domain translates into variation in process performance. This paper discusses the drawbacks of using the average approach to impact comminution testing and plant design. It considers breakage intensity from a single-particle testing perspective. To clearly delineate breakage behaviour of each broken particle, an experimental technique using the JK Drop Weight Tester (JKDWT) has been developed by which actual comminution energy per particle and breakage intensities were measured directly. Four different ore types in ranges of -45+37.5mm and -22.4+19mm were tested at three energy levels of 0.1, 0.25, 0.5 kWh/t and six energy levels of 0.5, 1.0, 2.0, 2.5, 3.0 and 4.0 kWh/t, respectively. Sieved results of individual particles, notionally, t5, t10 and t50 showed the presence of large variability in their breakage behaviour, which was not captured by the standard JK impact breakage testing approach. In addition, the original JKMRC model is modified by introducing a third parameter, ‘Emint10’ which describes the minimum energy required to produce the minimum percent t10 for a given ore type and its significance is tested statistically. These results suggest that the analysis of breakage variability may lead to more robust plant designs. Perhaps, the most useful insight from this work is to extend single particle breakage model developed by JKMRC to a comminution percentile envelope which may provide a more detailed picture of ore breakage variability. INTRODUCTION Rock consists of mineral grains, pores, voids and cracks that may differ markedly in size/density which make rock a heterogeneous material by nature. The degree of heterogeneity in rock affects its breakage characteristics where these variations increase local differential strain and stress within a stressed rock (Scholz, 1968) and it depends on many factors such as rock genesis, alterations, etc. One important aspect of this heterogeneous feature is presence of a large amount of experimental scatter in rock breakage results when considered from a quantitative perspective (Bieniawski, 1967; Liu, Roquete, Kou, & Lindqvist, 2004)."

Jan 1, 2018

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

The challenges of nature for the recovery of metals for a sustainable future continue to present in diverse ways. Base metal deposits are becoming lower grade and more complex. Rare earth metal demand is soaring and must certainly be met from new sources outside of China. Precious metals have soared in value due to increased industrial usage and the importance of these metals as financial instruments. Many of the future sources of precious metals are complex and difficult to process. The field of hydrometallurgy plays an important role in providing technology for extraction of these metals for a sustainable future. Selected examples from the base, rare and precious metals fields will be used to illustrate how current developments are providing metals for our future. The recovery of rare earths by beneficiation, leaching, purification, precipitation will be described from a multi-mineral deposit in Canada. The recovery of metals from complex base and precious metal ores may be accomplished using chloride ? assisted high temperature pressure leaching. Finally, by way of example, the enhanced Galvanox? process for treatment of chalcopyrite concentrates using silver-activated pyrite as a catalyst will be illustrated. This process offers a viable alternative to the conventional smelting of chalcopyrite copper concentrates.

Sep 1, 2012

By F. C. Araújo, T. Tavares, J. Leite

"This work presents the small-scale mining cluster of kaolin in Rio Grande do Norte (RN) and Paraiba (PB), both Brazilian states, including the following information: number of companies, process flowcharts, production numbers, mineralogical (XRD) and chemical (XRF) composition, granulometric distribution (screen and laser granulometer) and image analysis (SEM). Some social indicators in the region of the RN and PB States are presented in association with these data. The number of companies and their flowsheet were obtained through in situ visits and sample collection for technological characterization. The comparative study of the different flowsheets for kaolin production in the world was done using the databases and presenting the state of the art of kaolin processing. The results indicated that the mean feed typically contains 35-39% kaolin with quartz, muscovite and kaolinite as main mineralogical components and SiO2 (65.83%), Al2O3 (21.19%), K2O (3.9%), and Fe2O3 (0,63%) as main chemical constituents. The products of mineral processing are twofold, one between 74 µm and 37 µm, and the other smaller than 37 µm. The wastes of operation had major quantities of kaolin. The average Human Development Index (HDI) of the cluster region is approximately of 0.61, which shows an association between mineral processing plant and social indicators. The kaolin recovery, however, is between 30-55% for the three most common types of flowsheets that are currently used in the small kaolin mining cluster, indicating a need for technological improvement to achieve regional development. These data could be used incrementally to adapt the process plant currently used in the small-scale mining cluster of kaolin."

Jan 1, 2014

By Roberto Galery, Priscila Esteves, Braz Cardoso, Marcelo Stopa

"It was developed in this work a computational tool to aid in anomaly detection present in the operation of ball mills. The tool uses a torque estimator that is based on measurements taken exclusively in the drive motor. The ball mill equipment widely used in the mining industry has, inherent to its principle of operation, high energy consumption and low efficiency. These characteristics are accentuated when the mill operates outside the ideal conditions of velocity and loading. Direct measurement of these variables is extremely difficult because it requires the installation of sensors in moving parts of the mill. Thus, systems that can help monitoring the operating conditions and predict anomalies are useful because they contribute to improving the performance of the process, help to reduce the energetic consumption, wear on the mill surface and frequency of maintenance shutdowns. The detection strategy implemented in this work is based on the fact that operational anomalies such as an inadequate percentage of balls and incorrect angular velocity manifest itself as a change in spectral components of the torque signal in the mill driven by an electric motor. The mill torque was estimated by processing motor variables measured by sensors commonly used for control purpose and installed exclusively in the motor. The mill was operated at various fault operating conditions and signals from electric motor and vibration on the mill shaft were measured. The spectral components present in the estimated torque signal were then compared with signals from a vibration sensor in order to establishing a correlation with anomalous operation condition of the mill. The experimental results showed that the signals obtained has an excellent correlation with other variables obtained by direct measurement and have potential to be used to construct a system for automatic fault detection in the operation of ball mills."

Jan 1, 2014

By S. Banisi, A. Haji-Zadeh, H. Asadi, M. Maleki-Moghaddam

One area in AG/SAG milling field which has received a great attention is the optimization of liner design for any application to increase the availability of mills. The Gol-E-Gohar iron ore concentration plant uses three 9m × 2.05m autogenous mills (AG) in parallel in a dry operation. The AG mill shell is lined with three series (57 cm each) of 36-row liners. Due to large variations in feed characteristics and inadequate blending, the performance of AG mills has been lower than the target value. Therefore, to improve the comminution efficiency, the optimization of the design of AG mill shell liners was applied in this plant. By simulation it was found that increasing the liner lifter face angle from 7 to 30° while maintaining the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. Measurement of the wear profiles of shell liners indicated that the wear along the liner length was not uniform and the highest wear occurred between 0.5 m and 1.2 m of the mill length. A new liner design was proposed by redistributing the metal from parts with a lower wear rate to the parts with a higher wear rate to arrive at a uniform wear profile along the liner length at the liner removal time. The non-uniform shell liner was constructed and installed in one of the three parallel dry AG mills. It was found that the first and second liner designs increased the mill throughput by 2.6 and 7.5%, respectively. After conversion to SAG milling on the account of liner change, 18% (from 413 to 489 t/h) increase in throughput was realized. It was predicted that the non-uniform liner designs will increase the liner life time by 10% and will reduce the scrap metal from the current value of 59% to 50%.

Jan 1, 2014

By A. Pandey

Over the years, Coal Beneficiation at Tata Steel - West Bokaro has seen varied changes. With increasing R.O.M throughputs & lowering of the concentrate ash, Fine Coal Beneficiation process has thrown up myriad challenges. Development of Synthetic Collector was initiated couple of years back with Technical assistance from NLC Nalco India Ltd. Coal from West Bokaro unit was sent to Nalco?s Naperville (US) research lab for developing Tailor made synthetic collector . After comprehensive lab flotation studies, synthetic collector was developed & recommended for plant evaluation. The lab scale results were very promising in terms of improved separation efficiency & yield at similar ash level. The collector sample received from Nalco research laboratory were revalidated at Nalco Kolkata lab and finally at Tata Steel West Bokaro lab, confirming the promising results. (S.E 25-30 % better than HS Diesel) The key factors playing out for this improvement initiative are a) Scope for improvement in Clean Coal Yield at same or lower ash level coupled with improved Selectivity and Separation Efficiency b) Introduction of a Synthetic Collector with a Green Chemistry and subsequent replacement of H S Diesel, which is highly inflammable with a less inflammable & safer product Trial was conducted at plant scale in two phases and comparative performance of the Collector vis-à-vis Diesel was evaluated across the following Coal Seams of Q- SE (Seam VII, VIII, VI, IX and X). The results generated are very promising and the improvements observed are summarized below. ? Separation efficiency improvement by more than 20% observed. ? Flotation Fines yield increase varied from 0.6- 1.5 % on raw coal basis across different seams. ? Consumption pattern is 20-25 % lower than Diesel. Keywords: synthetic collector, west bokaro, coal beneficiation, HSD

Sep 1, 2012

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By A. V. Faiberg

Currently, the interest to conditioning of cyanide-bearing recycled solutions with high-grade of base metals, in particular, copper has significantly grown. This can be explained by two major factors. Firstly, there are strict regulations on cyanides amount in tails and higher cost of detoxification processes. This problem can be easily solved during the ore treatment using the conditioning of solutions and water recycling. Secondly, the presence of other metals minerals which react with cyanide during gold leaching resulting in high cyanide consumption. The presence of copper is a major problem. Many copper minerals react with cyanide with the formation of cyanide complexes-Cu(CN)2-, Cu(CN)32- and Cu(CN)43-. One mole of copper consumes 2-4 moles of free cyanide. Availability of cyanide-soluble copper minerals has deleterious effect on gold leaching (gold recovery, cyanide consumption, tails detoxification, efficiency of gold elution and electrowinning). The precipitation of copper from the solutions improves gold recovery by CIL. The removal and recycling of cyanide allowed the reduction of cyanide addition to the process. The recycling of spent cyanide-bearing solutions based on the removal of copper and the return of cyanide bound in complex compounds for leaching process is an optimal way of solving the problem of gold-bearing copper ores treatment. By using the technology, an adverse impact onto gold recovery process is eliminated and at the same time reducing the cyanide consumption. Today, processes and methods of high-grade copper leaching solutions conditioning before and after gold recovery have been developed, which combine two ways of copper recovery: as a saleable product and cyanide to recover gold and reduce total operating costs. They are Cutech, MNR, SART, Cyanomet, AuGment, Vitrokele, Hannah and Cyanisorb. At the same time, these technologies have not been studied enough and described in literature. Data on parameters and operating conditions as well as introduction is not available. The conditioning technology of recycled solutions developed by IRGIREDMET JSC allows copper to be recovered as high quality concentrate and at the same time free cyanide regeneration in the recycled solution which is amenable to gold leaching. This technology was commercialized at a mine in Kazakhstan in 2008. The removal and recycling of cyanide does not require additional cyanide and is cost-effective. More cost-efficiency is achievable through selling copper concentrates, closed water cycle without the detoxification of effluents and enhanced gold recovery by CIL and cathode quality.

Sep 1, 2012

By H. C. E. Regidor, M. G. Mena, H. D. Mendoza

Cyanidation leaching has always been the most widely used method of extraction of gold in the world. Its low cost and high selectivity has made it the prevalent choice for mining companies, and even for the small scale miners. The use of cyanidation in small scale mining has been an issue for the longest time, mainly due to the operation’s lack of safety measures, health care or environmental protection regulations. In pursuit of more environmentally friendly methods of extraction of gold, several alternative extraction processes have been explored, one of which is chlorination. The chlorination process is advantageous when recovering refractory gold locked in sulfides, as it simultaneously oxidizes the surrounding sulfides as well as dissolve any gold exposed to the lixiviant. This research was conducted to study and develop a safer alternative way of extraction of gold from small scale mining operations, without compromising the recovery of gold. In this study, a variation of the chlorination process has been employed for a refractory flotation concentrate wherein the majority of the gold is locked in sulfides. Hypochlorite-bearing reagents were used as the leaching reagents, and the method developed was a 2-stage leaching process in differing pH conditions. The solution pH and Eh was monitored all throughout the runs, and aliquot samples were taken at time intervals for analysis. SEM-EDS imaging was used to determine the mode of oxidation of the chlorination process, and the image obtained showed that the oxidized layer followed the shape of the particle, suggesting a diffusion controlled process. XRD analysis of the sample before and halfway through leaching further confirmed the oxidation of the sulfides. The amount of gold dissolved in the aqueous solution and in the solid residue were used as the basis for the determination of the recovery of gold. An average gold recovery of up to 84.38% was obtained using the developed method in just 7 hours of leaching. This method was then employed for a pilot-plant scale test and a gold recovery of 79.2% was obtained.

Jan 1, 2018

By Lawrence Bbosa, Aubrey Mainza, Indresan Govender

"Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to develop a probability based model for the power draw of a tumbling mill. Experiments are conducted using dry spherical glass bead charge in a laboratory scale tumbling mill, which is mounted with a torque transducer and tachometer to measure mill power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For both sets of data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. The information from both techniques is then used to develop a model for the power draw as a function of particle size, mill speed and volumetric filling. Predictions of the model match well with measured and calculated values. The model is found to predict mill power within close agreement with measurement and follows trends consistent with existing work on tumbling mill modelling."

Jan 1, 2014

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei and these ores require mineral processing to remove the substrate/nuclei rock before smelting. This paper reviews the results of jig separation and air table treatment for the coarse fraction and flotation and hybrid jigging for the fine fraction. Using these techniques substrate/nuclei rock was removed from the cobalt-rich ferromanganese oxide components. The mineralogical properties and metallurgical treatment methods including hydrometallurgical treatment of low grade ore is also reviewed.

Sep 1, 2012

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By T. Badrujaman

In September 2005, after 30 years experiencing in operating an ESF using a falling water film shell cooling system, Antam entered the new era in operating an ESF, after completely modernized its ESF No. 2 from a falling water film shell cooling system to a copper cooling system. Further, in the beginning of 2007, Ferronickel plant No. 3, where its ESF also uses copper coolers, was successfully commissioned. By operating an ESF using a copper cooling technology, Antam has to face some challenges to establish the operation stability. Besides that, the chances to maximize the furnace efficiency are greatly opened. The shielded-arc mode of electrode tip is selected to operate an ESF under relatively high furnace power to produce metal having tap temperature below 1500? and slag having tap temperature below 1600?. It leads to electric current unbalance. Further, operating an ESF using a copper cooler system under high voltage as consequence of the furnace power raise increases metal and slag tap temperature. This condition damages furnace integrity fast. Besides that, relatively high metal temperature increases its pressure during metal tapping. It leads to failure in closing the metal tap hole. The main different ways in operating an ESF using a falling water film shell cooling system and a copper cooling system lie in the electrode tip mode, the water specification used for cooler, metal tap block maintenance and allowed metal & slag level in furnace. Since a copper cooler system allows an ESF to be operated by consuming nickel ore having ratio Fe / Ni up to eight and producing slag having relatively high Fe content in slag, an undesirable silicon reversion phenomenon becomes an obstacle in reaching the operation stability. A copper cooler technology lets Antam to take a chance to increase its capacity. Modernizing the ESF No.2 had increased its furnace power from 17 MWh to 25 MWh. Meanwhile the ESF No. 3 can be operated up to 42 MWh. This technology allows an ESF to be operated under relatively high furnace power above 25 MWh safely as well as prolong the campaign life of ESF brick. Further, lowering ESF power consumption, extending the limitation of ratio S/M in nickel ore consumed and adjusting Ni grade in ferronickel product can be gained by applying this technology.

Jan 1, 2014

By H. J. Schulze

From a colloidal science point of view (Schulze 1984, Nguyen & Schulze, 2004) five micro-processes are responsible for successful particle-bubble formation: the approaching of the particle to the liquid-air interface, the thinning and rupture of the intervening liquid film, the expansion of the three phase contact perimeter, the generation of sufficient large capillary force to stabilise the aggregates and the transport process of particles into and within the froth layer. Flotation reagents influence mainly the thinning and rupture of the intervening liquid film between particles and air bubbles, the expansion of the three phase contact after the rupture of the liquid film and the stability of the aggregates against external destruction forces in the flow field. But it exist also a non-negligible influence on the approaching of particles to the bubble surface during the encounter process and on their passing over into the froth layer and the froth stability.

Jan 1, 2003

By G. Venkateswara Rao

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of Iron ore fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of Iron ore fines. The results obtained from this study revealed that among the parameters studied, drum rotation, amount of wash water and angle of inclination play dominating roles in controlling the yield and grade of the Iron ore. The majority of the newly developed Multi gravity concentrators have tremendous potentials for various applications. Therefore, the performance evaluation of these concentrators treating various minerals, coals, heavy metal recovery from tailing dams, etc., have become an active research topic. Several attempts have also been made to develop appropriate mathematical models of individual concentrators. Despite all these efforts, these concentrators have yet to find the widespread applications they deserve. The ?as received? sample assayed 40.80% Fe, 40.90% SiO2,0.24% Al2O3and 0.20 % LOI and all other trace elements within the specified range. The current paper deals with the Mineralogical studies, characterization and process amenability studies of Sub grade Iron ore from Deposit No. 5, Bacheli complex of Bailadila using Multi Gravity Separator (MGS).

Sep 1, 2012

By Janusz S. Laskowski

The flotation-related properties of hexanol derivatives and mono-alkyl ethers of propylene oxide, which include many important flotation frothers (e.g. MIBC, DF-200, DF-250, DF-1012, etc.) have been studied. The obtained results show that the DFI (Dynamic Foamability Index) - CCC (Critical Coalescence Concentration) plot can be used to classify flotation frothers. The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers.

Jan 1, 2003

By Kamalendu Bhunia

With the progressive depletion of known resources of good quality coal and minerals as well as the increasing demand of these minerals by different user industries, the emphasis has been shifted all over the world from selective mining to bulk mining followed by up- gradation to obtain the required quality of concentrate. The column flotation cell is one of the alternatives to reduce the gangue content of fines because of its inherent characteristics viz. easier to operate, low space required, no moving parts etc. A laboratory flotation column is used to conduct experiment. Present work has been undertaken to observe the effect of process variables (gas flow rate, feed/slurry flow rate, and frother concentration) on gas dispersion parameters (gas holdup, bubble surface area flux) in collection zone and to explore the effect of feed (slurry) inlet orientations and gas flow rate on column?s metallurgical performance. The effects of solid particle concentration, size and type (hydrophobic and hydrophilic) of solid on gas dispersion parameters have also been investigated. Test work has been performed in a continuously operating Perspex column (10 cm in diameter and 168 cm in height) using coal, sphalerite and dolomite as solid. Gas hold-up has been measured by phase separation method and mean bubble sizes are estimated from a drift flux analysis. The influence of operating parameters on bubble surface area flux has been discussed. It is observed that gas holdup in collection zone is affected by air as well as feed flow rates and also solid?s type. It is also found that addition of solid decreases the gas holdup and rate of decrease in gas holdup increases when solid concentration increases and particle size increases. Increase in gas flow rate increases recovery in collection zone due to increase in number of bubbles per unit volume of the column. From the experimental results it is evident that cross-current orientation of feed inlet shows slightly better metallurgical performance compared to other orientations. Keywords: column flotation, gas holdup, drifts flux, bubble size, bubble surface area flux, hydrophobicity, and recovery

Sep 1, 2012