Search Documents

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By Luo Yang

A one-dimensional wave equation based algorithm for estimation of shaft and toe resistance of driven piles using High Strain Testing (HST) data is presented. The pile is represented by a uniform elastic bar, while the soil around the pile is assumed as a homogenized isotropic medium, and Smith model is adopted to represent soil-pile interaction in the wave equation analysis. In most cases, the displacement of pile particles along pile shaft is greater than recoverable soil deformation (i.e., soil quake in Smith model). Therefore, static shaft resistance could be reasonably assumed to be totally mobilized during pile driving. Smith damping factor is used to account for combined dynamic and rate effect. Force and velocity time histories measured at the pile head are used as input boundary conditions in an analytical solution of the one-dimensional wave equation. As a result, two unknown parameters, static shaft resistance and Smith damping factor, can be incorporated into the one-dimensional wave equation and determined analytically for the time duration prior to the first downward wave reaching the pile toe. Then, soil resistance and Smith damping factor at pile toe can be further determined. The advantage of the proposed analysis technique is that the Smith damping factor and the static soil resistance can be directly determined based on the closed-form solution of the one-dimensional wave equation, which is computationally efficient. Numerical examples are given to illustrate the use of the proposed method to determine the pertinent Smith model constants and the static resistances.

Jan 1, 2006

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By D. R. Dance

The Resonant, or as it has more commonly come to be known the 'Sonic' Pile Driver, dates back to the early 1960's, when prototypes were produced by Charlie Guild, of Providence, Rhode Island, and A1 Bodine of Los Angeles, California, these were later to be developed into the unit known as the BRD 1000. Based on this initial work, the Shell Oil Companies of Sonico and The Resonant Pile Corporation, produced and operated 30 of these BRD 1000 machines, which were used throughout the U.S.A. and Canada on a wide range of foundation projects. Subsequent to this, Raymond International and G K N, of England, operated units on programs; the G K N units being of slightly modified configuration. In 1973 Hawker Siddeley Canada Ltd., acquired the license for the Pile Driver and related systems with the intent of promoting the use of the machines to install support pilings on the Alyaska Pipeline Project, but this did not materialize due to problems with the oscillator. After radical redesign and field testing of the oscillator system the unit was employed on a number of test projects principally in Northern Canada and Alaska.

Jan 1, 1987

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

By Marie-Pierre Bourdouxhe-Barnich

Since 1997, in partnership with the Laboratoire Central des Ponts et Chaussées in Strasbourg, ProfilARBED has been carrying out a vast study to qualify the improvements jetting can make to vibratory driving of steel sheet piles, and to understand its effect on the surrounding ground and on the sheet piles themselves. The process basically involves discharging a fluid (mostly water, sometimes in association with air) at controlled pressure and/or flow rate near the toe of the sheet pile being driven. The steel jetting pipes are attached to the sheet pile and are connected to the pumps by hoses. The jet of fluid loosens the soil, thus reducing the resistance at the toe of the sheet pile. Depending on ground conditions, the fluid that flows along the pile can reduce skin friction. Four soil types were involved in our experiments. Each site was instrumented: the driving parameters and the geotechnical characteristics of the soil before and after vibratory driving and jetting-assisted driving were recorded. Each test provided its own particular information which contributes to overall thinking on the matter and is of help to project managers who are often confronted with rapid driving to the final depth.

Jan 1, 2002

By Padmavathi V. Sagi

In this paper, effect of cyclic loading on the behavior of a long, flexible, unrestrained vertical pile loaded laterally in soft clay is examined. For cyclic loading, the analysis is carried out using a new method for the construction of p-y curves and for static loading conditions, p-y curves proposed by Dewaikar and Poonam (2005) are used. An iterative analysis is employed with secant modulus approach using a matrix method known as moment area method developed by Sawant et al. (1994). For pile top deflection of 20% of pile diameter, the load values are computed for both static and cyclic conditions. The comparison of results with the field test results reported by Matlock (1970) shows a good agreement. A parametric study is further carried out to examine the effect of load eccentricity, pile embedment length, diameter and the number of cycles on the pile response. The results of this study are discussed in the paper.

Jan 1, 2006

By Osamu Taki

This paper presents the system, the strength of column, the design concept, and the applications with four case histories from the past project as the general aspect of Geo-Column (trade mark of single soil-cement column by SCC Technology, Inc.). In the system, it shows the installation process and drilling/mixing tool with the mixing process. In the design concept, it shows how to design Geo-Column against the vertical and horizontal load. Finally, it shows the applications with four case histories, (1) building mat foundation, (2) isolated foundation on the pedestrian bridge, (3) bridge spread footing and slope erosion control wall in the channel, and (4) cut-off wall and shoring wall in the underpass roadway to the railroad.

Jan 1, 2000

By Li Tiemin

It is one of important tasks in research of vibratory pile driving to increase speed of pile driving and depth of pile driving -- this means to increase capability of penetrating hard layer. In general, vibratory pile driving hammer make pile be situated in vibratory situation to drive pile by means of weight of hammer and pile, but the depth of pile driving and capability of penetrating layer are limited by dead weight of hammer. This paper introduces a new kind of vibratory pile driving hammer which differs from general ham­mer. A set of pressing system is attached to hammer and pile driving frame. The pull of winch installed on frame passing guide pulleys bring downwards press to pile through absorbing system of hammer. The practice and comparison test have showed that the new hammer is faster in pile driving and bigger in capability of penetrating layer than general one. Now, the vibratory pile driving hammer with pressing device has been applied widely in China. RESUME: The vibratory pile driving hammer based on vibratory principle to design have applied wide­ly in foundation engineering in many countries over the world. In order to suit the needs of deep foundation, at present, how can quicken speed of pile driving and increase depth of pile driving have become even more value to many countries in the world. This paper introduces a kind of rapid vibratory pile driving hammer which can drive pile deeper and more faster comparing with common vibratory pile driving hammer. Therefore, a kind of simple and reliable method has been offered for rapid vibratory pile driving in deep foundation.

Jan 1, 1991

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

By Tianfei Liao

Extensive site investigations revealed that abandoned shallow mine workings exist under a site planned for construction of a major new facility. Since the mine voids were susceptible to collapse, they were stabilized by grouting. After completion of the mine remediation, three types of deep foundations (micro-piles, auger-cast piles, and drilled piers) were considered for this site. Micro-piles spread the load via the bond between the pile and the bedrock. Without significant length socketed in rock, the axial load of auger-cast piles and drilled piers has to be concentrated on end bearing. Although spreading the load is preferable in this environment, economic consideration dictated the choice of drilled piers for construction.

Jan 1, 2009

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By Xu Ronglie

This paper looks back on the developments and achievements of deep foundations, on the basis of the complex geological conditions and environments in China. It sums up advances in theoretical and applied researches, engineering constructions, practical experiences, case histories, and problems and developing prospects of piles and deep foundations in recent years in China.

Jan 1, 1991

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011