Search Documents

By Klaus Pöllath

This paper describes mitigating measures and the design of compensation grouting which will be executed from deep shafts of the Amsterdam North/South Metro line project. Due to the specific conditions for TBM-tunnelling in Amsterdam (historical buildings on pile foundations near the tunnel and soft soils with high groundwater levels) tunnel construction necessitates mitigating measures, such as compensation grouting or soil freezing. Züblin developed a special shaft construction method for critical distances to buildings. For the compensation grouting Züblin developed a new software tool, called SOFIA, which controls and visualizes and thus optimizes the entire injection process. This tool significantly increases the efficiency of the injection works while reducing the geotechnical risks.

Jan 1, 2006

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for optimization of existing foundations and subsequent re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2011

By Matthew Janes

Quality control procedures are increasingly important with today's higher capacity foundations and complex loading conditions. The need for a mobile, repeatable, nondestructive and economical load test method led to the development of an entirely new approach. The system described involves using solid propellant fuels to accelerate a reaction mass off the test pile. The force required to accelerate the reaction mass upward acts equally downward on the pile. Very high forces may be applied to the pile in a controlled, linearly increasing manner. The duration of the applied load is approximately 100 milliseconds. This rate of loading is slow enough to allow the pile and soil to react together as a composite rigid body. Pile/soil accelerations and velocities are low, typically 1 g and 1 m/s respectively. The effects combine to produce pile and soil response no longer dominated by the transfer of force via stress pulse (as with impact). Instead the pile force increases throughout the length of the pile, with pile top and toe stresses building in unison with time. This emulates the stress condition during static pile loading. Finally, state of the art instrumentation systems are used to obtain test data. Displacement is monitored directly using a laser datum and integrated receiver located at the centre axis of the pile. Force is also monitored directly using a calibrated load cell. Data is acquired and digitized using a 386 PC with user friendly software capable of producing load deflection curves and time histories in the field seconds after testing.

Jan 1, 1990

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By Huw Williams

It is becoming increasingly common practice to re-use existing foundations for new projects, especially on urban sites where geotechnical conditions are congested. A knowledge of the foundation dimensions and capacity is essential for this to take place, however, as-built records are often non-existent. Non-Destructive evaluation (NDE) is now becoming an important tool in assessing old foundation properties and their potential for re-use. Pile dimensions are also critical in the power industry, when they are supporting transmission towers which need to be upgraded, and may carry additional wind loading. This paper describes the application of various NDE techniques that are available and how they can be used to determine pile length, shape and capacity in difficult site conditions, including foundations under structures.

Jan 1, 2006

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Lawrence P. Goldfarb

This paper presents the results of the geotechnical investigation for the repair of the Fashion Island Boulevard Bridge, Bridge No. 350160, in San Mateo, California. The concrete, precast girder bridge suffered considerable damage during the Loma Prieta earthquake. The existing 36-inch, precast, prestressed concrete piles cracked and spalled at their tops. Based on analyses performed by Biggs Cardosa Associates, structural engineers, the piles did not have sufficient strength and ductility to resist the dead plus seismic loads specified in the Caltrans "Bridge Design Specifications". Additional support for the bridge was needed and the repair strategy consisted of installing large diameter pipe piles at the existing bent and abutment locations. This paper describes the geotechnical engineering analysis and design decisions for the large diameter pile design.

Jan 1, 1993

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By Jiwei Duan

The deformation and load transfer behavior of a single soil-cement column are studied with the finite element method. The results show that there is an effective length for a soil-cement column. Beyond this length, the settlement of the column is approximately equal to a constant. The effective pile length is introduced to the concentric cylinder approach (Randolph and Wroth 1978), and an analytical formula for estimating the settlement of a single flexible pile is presented. A second analytical formula for determining the effective pile length of a soil-cement column is obtained and an example shows that the calculated and measured results are in quite good agreement.

Jan 1, 2002

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By Fredrik Sarvell, Leo-Ville Miettinen, Veli-Matti Uotinen

"Abstract The continued concentration of building activities in cramped areas of city centres means more underground construction and facilities. Demand to minimize execution time and any kind of disturbance to business, general traffic, people and nearby technical structures is increasing. To answer these challenges foundation business has to develop schedule-wise and technically reliable deep excavation and foundation solutions in vulnerable surroundings and challenging soil conditions.Drilled pipe pile wall – RD-pile wall – is a combination of Ruukki drilled steel pipe piles and interlocking sections. Individual RD piles, typical diameters between 219 mm to 610 mm, are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole hammer (DTH) using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings.RD-pile walls have been used as permanent and temporary retaining walls for different kinds of demanding excavations and structures, such as bridge foundation, as quay wall and as sealing structure in rehabilitation of an existing dam. Rigidity and watertightness of the lower end of the RDpile wall is being researched as well as fire design issues examined. One of the most fascinating RDpile wall solution is to utilize the wall as a permanent underground basement wall. Reliable and rigid connection to bedrock decreases the bending moment and deflection of the wall and good fire resistance in addition to large variety of pile dimensions and steel grades gives possibilities to design and execute a cost-efficient basement wall and foundations without temporary retaining wall works. 1. IntroductionIn northern Scandinavian soil conditions, installation of sheet pile walls, or even secant pile walls, is often problematic due to the existence of hard and large boulders in the overburden, and especially when the retaining wall structure should penetrate to or into the hard bedrock. On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid-1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers)."

Jan 1, 2014

By K. Rambha Devi

The paper is an attempt to co-relate the findings of pile capacity using a number of formula suggested by various authors with the actual field load test results. Five locations consisting of wholly sandy or clayey soils were selected for this purpose. The clayey soils are on a hilly area having clays of medium to stiff consistency upto a depth of 20 m The sandy soils are near the bank of a river having angle of internal friction 'Ø' value ranging from 30 to 35 Degree. The details of the soil properties are given in Table-1 Bored cast-in-situ piles of 30 cm diameter and a length varies from 6.5 m to 13 m were designed and cast for load test to be carried out. The load applied was twice the design load. The load vs settlement curves were obtained. The theoritical values obtained by formula suggested by various authors were superimposed on the curves. From the careful study of these curves it is seen that De Ruiter and Berigen values are close to the actual results for clayey soil. For sandy soil it is found that both the BIS method and Meyerhof method found to give conservative resuslts. A multiplication factor is suggested to theoritical values for obtaining satisfactory results.

Jan 1, 1996

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002